Canon 650D [OLD]

[Ivarss]

WARNING: This will make both your card and your camera bootable. It should also be the only "permanent" change to your camera this build does, but I cannot guarantee you that

Reading that makes me wonder what that even means!

Not home right now so cant access my camera right now and get started!

[loplo]

After 1st boot up I go to upgrade firmware and let it update, next it goes to the main menu.  Hello World comes up, signature=0x12aeb7b3, enableBootDisk, oops!  In the top left corner in real small print "font addr bad"

What am I doing wrong?  If I try using the camera it seems fine but once it powers down on it's own I find the drive light came back on or right after the sensor clean if I shut it down on my own. 

I've reformat and tried about 5 times.

Where am I dropping the ball?

I assume you did not follow this:
Run EOSCard, select your card, make it bootable (check all the flags, don't touch the ML or CHDK buttons)

[Jseeker]

Correct, lens focusing requires props

About bracketing, are you sure it's not in the shoot menu under the name of Adv. bracketing? (no camera here, so I can't check, sorry)

About movie restart, can you check if the "clear overlays when recording" feature works?

MOVIE RESTART - Yes Overlay does clear when I hit record (after turning on this setting)

[baga]

I assume you did not follow this:
Run EOSCard, select your card, make it bootable (check all the flags, don't touch the ML or CHDK buttons)

I thought I followed it.  I use a Mac and used MacBook.

[blade]

About bracketing, are you sure it's not in the shoot menu under the name of Adv. bracketing? (no camera here, so I can't check, sorry)

under advance bracketing i have:
-bracket type
-frames
-ev increment
-sequence
-2 sec delay
-iso shifting
-post scripts

With all the options there it may be the HDR you mean, but noting called HDR

[loplo]

Same here. Could be something different on some cameras?

[baga]

I couldn't get the screen shot to upload so I just re-did everything again and then got stupid and tried moving files around (4g card) when that didn't work.  I still get the error message including the oops. 

I figure this part is normal.  Every time I turn the camera on/off/install batteries the firmware upgrade screen comes up and loads.  If I install my none ML 32g card no bootup and looks for upgrade file.
I'm not sure what steps to take.

[nanomad]

under advance bracketing i have:
-bracket type
-frames
-ev increment
-sequence
-2 sec delay
-iso shifting
-post scripts

With all the options there it may be the HDR you mean, but noting called HDR

What I meant is that it's called advanced bracketing now, but don't bother testing as it's not working in this build

[baga]

If I ignore the message and just start using the camera it works fine except for only 15 second movie of record time and then it turns the recording off. 

[Dr_Bigdiq]

Lets gets this going! I'm ready to get audio monitoring, I'm not sure if anything else matters!  Though it would be a bonus to have more manual features in video mode.

[blade]

What I meant is that it's called advanced bracketing now, but don't bother testing as it's not working in this build

Thats clear then wont test it....  testing video >4GB now...

[nanomad]

If I ignore the message and just start using the camera it works fine except for only 15 second movie of record time and then it turns the recording off.

Does this happen with of without the autoexec bin on the card?

edit: I'm in the chat (http://www.magiclantern.fm/forum/chat/index.php) if you want faster help

[blade]

If i film above the 4GB the counter gets stuck at 0:03... however the file is split and just continues to record

[baga]

Same here. Could be something different on some cameras?

That's the screen.

[nanomad]

I know that, but did you continue with the install procedure? Or did you stop right there?

[1ricca]

Up and running! Everything's great so far!

[nanomad]

To whoever is having issues, what OS do you have?

[1ricca]

Magic zoom is having issues on mine. Works when not recording. When recording, only Focus+Zrec works.

[Walter Schulz]

Is "Trap Focus" not working in this pre-alpha?

Ciao, Walter

[Jseeker]

Windows 8 (issue with MOVIE RESTART)

[nanomad]

To whoever is having issues, what OS do you have?

Issues with the installation, that's what I meant

[1ricca]

What happened with the chat? Keeps failing on me...

[a1ex]

There were more than 5 users logged in, so it threw a stack overflow

[breaker]

First of all, Thanks a lot for your work nanomad! 

I had the signature/oops issue during installation, but continued without any problem. ML autoloads during every startup. I don't have any issues with short video clips.
Issues i have seen : Canon graphics sometimes overwrites the ML menu (follow focus square). Magic zoom does not draw green lines when in focus, and splitscreen does not adjust.

I am using Win8.

[nanomad]

- Canon graphics sometimes overwrites the ML menu: Confirmed
- Magic zoom does not draw green lines when in focus: Confirmed, looks like the focus confirmation structure has changed (the address should be correct)