Etiquette, expectations, entitlement...@autoexec_bin | #magiclantern | Discord | Reddit | Server issues
Started by a1ex, October 11, 2012, 01:55:31 PM
0 Members and 1 Guest are viewing this topic.
Quote from: Sorin on July 21, 2014, 02:28:43 PMGreetings!It's my fist time posting on this forum, and I'm using ML on an EOS M.Generally, I can say I'm quite pleased with the features it provides but I'm here to report a bug, since i don't know where else to do so.So I've tried the following settings: - manual mode with exposure bracketing of 1 stop - continuous shooting - ML screen When I'm doing this, the camera freezes and it won't respond not even to the shut down button. Sometimes the screen makes some gray and red lines and it stays like that. After removing the battery all is good, but the pictures aren't saved on the memory card.This only happens with the ML screen. If I try using any other canon screen (by pressing the info button) then nothing like this happens.
Quote from: brockbrick1 on July 21, 2014, 11:37:54 PMIs my camera ruined
Quote from: jpaana on July 21, 2014, 10:43:49 PMI tried reproducing this but couldn't, took quite many brackets without problems (apart from a cosmetic problem of zebras filling the screen after the first frame). I use my own compiled binary, but it should be roughly the same as nightly from yesterday. Which info options you have enabled? I have disabled spot meter, only use focus peaking and zebras, otherwise default options.
Quote from: Sorin on July 22, 2014, 03:04:49 PMI was using the version labeled 2014Jul18 and previous. On the latest one, labeled 2014Jul22 it seems to be working.It was the same with some older versions in these past 2 months. So I guess this issue was fixed now. EDIT: now sometimes works, sometimes it doesn't.What specific settings should I tell you?The difference now is that it works when you do exposure bracketing but if you do just continuous shooting, at some point it freezes.
Quote from: jpaana on July 22, 2014, 04:16:59 PMAh ok, I tried this as well, took 30 frame "burst" without problems. By info options I meant the options in Overlay tab (spot meter, zebras, focus peaking, histogram, etc.). Also any other settings that might be relevant like whether you shoot raw or jpeg (I used raw) and so on?
Quote from: Sorin on July 22, 2014, 08:13:41 PMI've tried as you said, and I've firstly unchecked all of the Overlay tab options, then checked them one by one. It happens when I enable the Magic Zoom (F+HS, Med). I've tried it with all the other options checked and unchecked, and it seems that this is what's causing the problem.Also when I've changed the picture size from either largest L or RAW to S3 I've got the error message Error 70.On the previously mentioned picture size, the camera just freezes without giving any error message.
Quote from: Robbe on July 07, 2014, 11:37:14 PMInstalled latest nighly build, 2014Jul02, (tried also with earlier versions), loaded raw_rec module and reboot.The Menu/Modules shows raw_rec OK, but Menu/Movies are all dimmed and no green dot. In Menu/Modules/RAW video shows N/A, but I can set resolution and record. Just after recording, the green dot lights and showing resolution. But when reboot there is no resolution showing and no green dots. Have to start over again every time.
Quote from: 1anl on July 25, 2014, 04:22:14 PMBut when I do enter LV I can record raw but, the dual ISO option remains greyed out on the Expo menu although I can select a recover ISO value by selection the Q button.
Quote from: jpaana on July 22, 2014, 09:29:18 PMThanks, didn't get this reproduced with Magic Zoom + raw (though I did get an error message about "Raw error, falling back to YUV" or similar, probably from raw histogram I had enabled), but got it to hang with Magic Zoom + S3, without error message though. I'll enable some debug options in my build and see if I get any meaningful info out of it.
Page created in 0.247 seconds with 15 queries.