External Monitor Recommendations with MLV Raw Recording

Started by swinxx, March 03, 2015, 01:29:16 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

extremelypoorfilmaker

Hi guys, here's the video i was telling you about of the Aputure VS-2 i hope it will be usefull:


CineRAW

@extremelypoorfilmaker where is the video? Can you share it again or the workflow you get with Aputure VS-2.

thanks in advance

extremelypoorfilmaker

Uh! I think I deleted that video.

anyway, was a pretty useless video I must say. Nothing that can be done in writing.

so, canon 5D3 + Magic Lantern + Aputre VS2:

The monitor works fine with the 5D3 with Magic Lantern running alongside Canon FRIMWARE 1.2.3 Note you can't have external monitoring with firmware 1.1.3 firmware 1.3.3 has not been ported (yet).

Just connect camera and monitor via HDMI (best resolution) turn monitor on and then camera. If you have the mirroring option selected in your Menu, you will have a clean feed from the camera with no overlays. All the overlays will remain in your camera monitor. With No-Mirroring, the monitor will became de facto your primary monitor with no image being displayed onto the cam display.

In order to review your RAW footage with the monitor you will need to run it in no-mirroring mode. If you do so, it will work fine, but the background of your monitor will display all sort of craziness instead of being BLACK like it normally is through the camera display.
Worry not. I do not know why it will do that, but it brings no harm to either the cam or the monitor.

The monitor has focus peaking (ML focus peaking is better) False color, Zebras, cropmarks. All works fine. But still, Magic Lantern own cropmarks, zebra etc. are far better than the monitor ones.

In essence: Don't buy it.
The battery slot at the back will be a bit funny with certain batteries: If bent with the battery facing the ground there is the risk that the battery will disconnect and you will need to tape it to the monitor so that it will not go off as you are shooting.

The deal breaker: UNUSABLE outside even with the shader. The screen is so glossy, that you will end up looking at yourself instead of what's going on inside your frame. Perfectly fine in darkness or interiors.

My advice: Spend an extra £/$/€100-200 and get a better brand.

CineRAW

Thanks for quick reply @extremelypoorfilmaker

Did you upgrade? Which one did you upgrade to?

I'll take your advice on not buying this monitor. @deafeyejedi recommends the Atomos Shogun. Its a bit pricey but a great backup for recording ProResHQ.

I'm looking for a monitor that will let me see the ML overlays but does not have to record to an external hard drive like the Shogun.

I want to record MLV Raw with Sound. I am using Firm 1.1.3 Build Mar.02.15.

Thanks ML community

extremelypoorfilmaker

Quote from: CineRAW on March 05, 2016, 10:54:51 PM
Thanks for quick reply @extremelypoorfilmaker

Did you upgrade? Which one did you upgrade to?

I'll take your advice on not buying this monitor. @deafeyejedi recommends the Atomos Shogun. Its a bit pricey but a great backup for recording ProResHQ.

I'm looking for a monitor that will let me see the ML overlays but does not have to record to an external hard drive like the Shogun.

I want to record MLV Raw with Sound. I am using Firm 1.1.3 Build Mar.02.15.

Thanks ML community

If you want to be able to monitor externally, you should be upgrading to firmware 1.2.3 (Assuming you have a 5D3) There is no external monitoring supported for the firmware you are currently using.

I haven't upgraded yet because at the moment I am not in ned to. I will at some point, but If i will, I will probably sink my money in an Odyssey 7Q:

https://www.convergent-design.com/products/odyssey7q.html

This and the ninjas are quite pricey, but they serves as external recorders as well, so in case in the future you will pass from a DSLR to a "Big Boys" camera (Arri, Sony FS7 F5, C500, Aja cion, Kinefinity Blackmagic ursa etc.)

If you just need a simple external monitor, Lilliput does interesting stuff not too pricey.

But if you got money to splash, go for a ninja or odyssey :)

CineRAW


CineRAW

One last question.

How do you record your sound with 5dmk3 ML Raw Firm 1.1.3?

Is this list correct? There is no way to record sound into the camera?
https://builds.magiclantern.fm/#/features

Thanks in advance

extremelypoorfilmaker

Magic Lantern -> Modules -> turn on mlv_snd -> Restar your camera.

You can record sound with the module mlv_rec activated. (RAW Recording 2.0) Note, the sound will be regulated by audio options in canon menu.

After you have activated the modules you need: mlv_rec and mlv_snd go into Magic Lantern -> Audio -> turn ON MLV Sound

Simple!

CineRAW

Hey @exteremlypoorfilmaker I made a mistake. I already had the Sound option on.

I was trying to ask if there is anything that can be done to the Auto Gain Control. I used to have this control on my 5d mk2.

Do you know of anything? How do you record your sound? Just str8 from the internal mic? Do you have issues with noise? etc.

thanks

Walter Schulz


CineRAW

Hey @walterschulz

I am on 5d mk3 ML now and got used to using the sweet audio features found on 5d mk2 ML and 60d ML.

I only see a few options in MLV_Sound for MK3. Do you know what Trace output will do?

I'm am trying to record directly into the camera via a 3.5mm input jack from a wireless lav. I want to have more control over Gain/Volume. Is there a way to control that in 5d Mk3 ML? I already did a test with the lav and I can hear the internal mic through the headphones. Will ML separate those tracks like it does in 5d MK2 ML?

thanks again

DeafEyeJedi

Quote from: CineRAW on March 05, 2016, 09:01:18 PM
Hey @DeafEyeJedi thanks for the quick reply.

Can you please send details on 5d mk3.

For example,
1. Do you get MLV RAW with sound and you find that better than the ProRes422HQ with sound on the Shogun?
2. Do you know the color bit info on the MLV RAW and ProRes422HQ? Do you do post color corrections in Resolve, AE, both, etc?
3. Which firmware are you using to get both MLV RAW and ProRes422HQ? 1.1.3? Build?
4. Do you get ML Overlays while mirroring both? On both monitors?
5. Do you use RAW (1.0 Version)?
6. Do you use ML Viewer and export your MLV RAW or export DNG?


Thanks again for the help. Thanks to all the ML community for the support and progress.


@CineRAW-

1) Watch Video below.
2) MLV is 14-bit as per usual when ProRes422HQ from Shogun is only 8-bit (YCbCr 4:2:2) since that's the best for 5D3's HDMI output according to Canon.
3) 113 will give you ML or Canon layers (no clean HDMI out) versus 123 which has clean HDMI out however this test was done on 7D just because I like their audio features that ML provides. [emoji1]
4) Watch Video below.
5) Yes I do, in fact, I have been using MLV Lite lately which is just as good if not better.

MLV files were processed with MLP (with default settings and nothing else) just for this test purpose.

https://vimeo.com/158783572
5D3.113 | 5D3.123 | EOSM.203 | 7D.203 | 70D.112 | 100D.101 | EOSM2.* | 50D.109

CineRAW

Great sound test @DeafEyeJedi

I noticed you have ETTR option on the bottom of your ML Overlay. Do you know if I can get the same option on the 5dmk3 Fir113? Or do I have to use the histogram?

thanks again ML community

axelcine

Excellent sound. And if my eyes and ears don't deceive me - you have both a shotgun mike and a label mike attached to the Shogun. Excellent, and a good enough quality for broadcast interviews. A lot of hard working and experimenting ML-users, who excel in good raw footage should see your demo video and try experimenting with "raw sound" as well instead of just putting a piece of music  in their movie. When you master the shooting, playing with natural sound makes the experience complete and very satisfying.

Gotta go get me a Shogun one of these days - I've found a good teacher, DeafEyeJedi!!!

Latest: I can understand why you used the venerable 7D, since it has a full Audio/ML menu. How does your setup work with 5D3 (both versions)?
EOS RP, 5dIII.113/Batt.grip, 5dIII.123, 700d/Batt.Grip/VF4 viewfinder + a truckload of new and older Canon L, Sigma and Tamron glass

DeafEyeJedi

@axelcine -- I'll do another test comparisons in between 113 & 123 re: audio wise on 5D3 as soon as I can. Meanwhile, here's this screenshot that helped my decision making in purchasing the Shogun.

5D3.113 | 5D3.123 | EOSM.203 | 7D.203 | 70D.112 | 100D.101 | EOSM2.* | 50D.109

adrjork

Hi everybody,
I've read all this topic and I admit that I'm a bit confuse:
I'm simply looking for a 7" external monitor for my 5D3 fw 1.2.3 + ML. My needs are:
1. using the external HDMI monitor while recording MLV_raw+audio without loosing frames (consider that the gimbal I would buy - the Moza Lite2 - is connected to the 5D3 via USB);
2. recording at 1920*1080 @ 24fps, and seeing it on the external monitor without latency at the same frame-rate of 24fps (but better if at a lower resolution, like 720p);
3. possibly having the ML overlays on the external monitor;
4. if not, having at least a good internal focus peaking;
5. possibly a good internal zebra;
6. a lightweight monitor model (possibly not over 450gr).

I'd like the Lilliput 664/O/P but on their chart of supported models it seems that 664 doesn't support 720p/24Hz (http://lilliputdirect.com/index.php?_route_=supported-hdmi-modes)

So I'm in doubt (I'm a newbie here), and I decided to wait for someone that could suggest any tested monitor model that possibly fits my six points.

Thanks really really much for your help.

P.S. Please, could you suggest also a 5" version monitor that matches my six needs? (Thanks again.)

PaulHarwood856

I'm a bit late to this forum posting, but I use a MustHD 7 inch monitor. Very accurate colors, has HDMI lock, HDMI in and out, and works flawlessly with my 7D. There are HDMI options in the 7D ML Menu, I believe I use 16:10 HDMI.

- Paul Harwood

alex_THC

I just purchased the Atomos Ninja Blade to monitor while shooting RAW on my 7D. 

Unfortunately, I can't record raw internally without getting a glitchy image in the lower portion of the image.  I've gone into Display settings and turned on the 'Force HDMI-VGA' setting, which I read will bypass that problem, but now the Ninja Blade reads 'No Input.' 

Any suggestions?  I guess the Blade doesn't read an input lower than 1080?  If it can't monitor while filming in RAW, it's kind of useless.


*I'm referring to screen tearing when I say 'glitch.'
Thunder Hill Cinematics

Andrew Losurdo

Maybe you can try Feelworld 7'' monitor.I buy it from Alibaba,and I think it is very nice.
It is IPS panel,1280*800 resolution(support 4K UHD 3840*2160p is optional),HDMI AV in,and functions like Exposure,Histogram,False Colors,Peaking Focus Assist ,etc.
HDMI support:
480i / 576i / 480p/576p   
1080i (60/59.94/50)   
720p (60/59.94/50/30/29/25/24/23.98)   
1080p(60/59.94/50/30/29.97/25/24/24sF/23.98/23.98sF)
And it is light weight 0.4KG,super slim 17mm thick.

alex_THC

Does anyone know what the specific frame-rate and size for the 7D setting 'Force HDMI-VGA.'  Is it 720p23.98? 

According to the Atomos website, the Ninja Blade accepts 720p60, 720p59.94, 720p50, & SD 480i.  I'm still hoping to get the monitor to work while shooting RAW on the 7D.  Any help is appreciated!

*Monitoring on the Blade works when I have the Canon settings at 1280x720p60 - with ML 'FPS Override' set to 23.98.  When I import the footage, the image is squeezed vertically (1728x584 for 16:9), which requires extra scaling in the computer.  Does anyone know if I lose information filming this way?  Thanks.
Thunder Hill Cinematics

ibrahim

Quote from: QuickHitRecord on March 03, 2015, 08:04:33 PM
I use a SmallHD AC7 when recording raw. No problems so far, though I am still using 1.13. I wouldn't mind if it were a little smaller (I think that 5" would be perfect for this camera), but sometimes the extra real estate is nice -- especially when dealing with the super shallow DOF of the 5D. It also has a useful anamorphic scale mode if you ever shoot with those lenses.

Interesting. Since you used 1.1.3 you could only see the monitor while the camera screen was black right? i.e. not being able to use both cameras and external monitor at once.
Are you able to see verything on the monitor from overlays, zebras, LUT, etc.
However, I am trying to find SmallHD AC7 but it seems that it no longer sold and discontinued. What is the new upgrade version of AC7? A 5 inch would be sufficient.
Canon 5D Mark IIIs | Ronin-M | Zeiss 50mm 1.4 planar | Zeiss 35mm 1.4 distagon  | Zeiss 24mm f2 distagon | Zeiss 85mm f1.4 planar
Dual sound system: Tascam DR-60d MKII | Audio Technica AT899 | Sennheiser MKE 600

Kanakori

I have pretty much the same question but with a lower budget. I need a monitor for my 5dmk3 with a ronin-m. I need it to work with 1.1.3. I just need it to assist me in framing and focus while I move with little to no latency.

pgrandaw

I use the Bestview s7II monitor with ML 1.1.3 on my 5diii and it's been working well. (I'm still using ML's 5d 113 because I'm shooting lots of widescreen slo-mo footage using crop_rec)

The reason I like this monitor (1920x1200) is a nice build, bright enough for the money, ($190 on Amazon) and 7 programmable buttons. It has built-in zebras, false color, histogram, peak, audio levels, etc., and can also run off the included DC power! It accepts 4k input.

The Main Issues I've seen so far are these, which are still workable to use as a non-recording field monitor for the 5diii :

1) SOUND - If using the 5diii, TURN OFF the Bestview monitor's audio meters function that's built into the monitor* and use ML's meters display to monitor because the sound doesn't carry through the HDMI output from the 5d to the monitor via the cable - at least not in ML 113. Since I record sound externally, I pump it back into the line input on the 5d. You can easily set input levels on the 5d manually to match external recorder levels (I use Zoom h5 with shotgun or lavalier mics). This way you're recording a great reference/backup track to sync your external audio later.
*also you'll want to mute the monitor's sound if it is going through to the monitor from the camera to eliminate feedback

2) HISTOGRAM/ZEBRAS - My main struggle I'm trying to figure out is the difference in EXPOSURE histogram/zebra levels between ML and the monitor's built-in histogram when exposing via ETTR. The test footage I've recorded show ML as being correctly exposed to the right, whereas when I've set exposure using the monitor's built-in histogram/zebras for exposure, it records somewhere between 1-1/3 to 1-2/3 underexposed. I'm sure this is somehow due to the 5d's limited output from the HDMI that the monitor is reading to determine levels. Unfortunately I don't see anywhere to compensate to be able to use the monitor's built-in histogram or zebras.

3) FALSE COLOR - I prefer ML's false color over the built-in one. Bestview's whites and blacks come through both as different shades of magenta and I don't see anywhere to change the color scheme in the menu. ML shows a nice difference throughout the exposure spectrum, easier to read.

My preference is to skip the monitor's fun functions and to use all ML's display options which show through on the monitor because exposure all appears accurate after processing. (I use MLV app https://ilia3101.github.io/MLV-App/ and edit in Resolve).

Does anyone know if the "clean HDMI" output in ML's 5D v123 somehow addresses the inconsistency of exposure levels between ML and external monitors? Or could this possibly just be an issue with this particular monitor or setup?

Thanks, and I enjoy the reading!
Patrick

ps. here's a quick peek at my 5d setup

Canon 5D3,1.1.3 CF-SanDisk Extreme PRO,160MB/s, 256GB, SD-SanDisk Extreme, 90MB/s, 32GB.

DeafEyeJedi

Quote from: pgrandaw on July 22, 2018, 06:47:14 PM
Does anyone know if the "clean HDMI" output in ML's 5D v123 somehow addresses the inconsistency of exposure levels between ML and external monitors? Or could this possibly just be an issue with this particular monitor or setup?

Maybe this will give you an idea re: 5D3.123...

5D3.113 | 5D3.123 | EOSM.203 | 7D.203 | 70D.112 | 100D.101 | EOSM2.* | 50D.109