Author Topic: [UNBRICKED] Bricked 60D Err 70  (Read 115939 times)

fryedr1c3

  • Just arrived
  • *
  • Posts: 1
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #100 on: July 18, 2015, 12:16:34 AM »
Hello,

Also having a similar problem as others. Using a Canon 7D, camera will boot in "C" modes, but will automatically display Err 70 if changed to other modes. Problem came about when trying to change the file format to save in .crw when it was connected to my computer in one of the other modes. Thank you for any advice or help with this issue.


Here are the Crash and Log Files
Crash:

ASSERT: FALSE
at DevelopCombination.c:52, task RscMgr
lv:0 mode:0




Magic Lantern version : Nightly.2015Jul02.7D203
Mercurial changeset   : bcd2d84120a5 (unified) tip
Built on 2015-07-01 22:30:47 UTC by jenkins@magiclantern.fm.
Free Memory  : 258K + 2961K




Log:
http://pastebin.com/k7npUFUf

JFG

  • New to the forum
  • *
  • Posts: 5
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #101 on: August 18, 2015, 03:23:04 PM »
Hi everybody,

I have been having the same issue with my 60d. I have seen on this forum that similar situations were successfully resolved. This gives me hope. My problem is almost exactly the same than the one documented by other users:

1) The camera got wet and since that, I kept having Err 70.

2) Most of the time (this is not consistent), I am able to open it in C mode after having removed the battery. This works with only one of my lens (EF-S 55-250 IS). When it does, everything is functional: each control beside de “mode wheel” is responding, autofocus works, it can take a picture and menu can be accessed flawlessly. This was tried using different lens, card and battery. From my point of view, this suggests that this is not a hardware issue although I can’t be 100% sure (camera was ON what it got wet).

3) Iwas able to upgrade the firmware to 1.1.1 however after the incident. However; I have not been able to open the camera with a SD card mounted for a few days. This fact given, I was unable to install Magic Lantern in order to get a crash log (yet) but I’ll continue trying it since I am aware that this log could help diagnose the problem.
I tried resetting the picture parameters using gphoto2 by following the previously shared instructions. The software was successfully installed but the procedure did not give any results.

Of course, any help in resolving this situation would be appreciated. From what I understand, the camera can be rebooted by using a modified autoexec and this would allow me the clear camera settings. If this is the way to go, I am wondering if someone could please share with me the modified autoexec and some basics instructions.

Please let me know if more information is required.

Thanks in advance,

JFG
m.jeanfrancoisgagnon@gmail.com

Dahoward

  • Just arrived
  • *
  • Posts: 1
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #102 on: September 22, 2015, 06:56:40 PM »
Hey yall I have similar issues except I cannot get to the menu screen.  Changed batteries, sd card, and even used different batteries/cards.  Camera got a lil wet, still turns on n off easy n gives me the good ole error 70.  I read the forum but I'll make it simple, I'm not to tech savvy with still cameras. 

IvanC14

  • Just arrived
  • *
  • Posts: 1
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #103 on: January 15, 2016, 05:35:09 PM »
I have the same problem with my canon, err 70, I try everything, remove sd card, format it, remove battery, install new firmware, reset to factory settings.
Using it on C mode, if anyone can send me the exe file I would be very thank full, this is my email:  ivan.700@hotmail.com

Gusto

  • New to the forum
  • *
  • Posts: 2
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #104 on: March 08, 2016, 04:47:11 AM »
Please help.. i have same err 70 too and i already installed magic lantern.

ASSERT: 0

at Evf/EvfState.c :1190

mic32

  • Just arrived
  • *
  • Posts: 1
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #105 on: August 28, 2016, 04:38:20 AM »
Hello Alex,

for me now is near the same issue with 60D +  Err 70
Get error when camera was become slightly wet in backpack after longer rain.

Today on the beginn the camera was able to boot in C-mode WITHOUT ML-SD-Card.
I updated canon-firmware from 1.1.1 to 1.1.1 again without errors and "err 70" was still showing me after fir-update ith ability to load in C-mode,
then i downloaded the nightly build of ML for 60D and after i tryed to update to ML-firware, camera show me just only "Err 70"-message in all modes (C-mode too) and only with ML-SD-Card.

I need autoexec.bin with disabled assert handler to reset the settings.

Thank you in advance.

So here is LOG000.LOG for more details:
     86:   140.552 [JOB] PROP_CFN_TAB2 3 0
     87:   140.834 [STARTUP] ERROR ASSERT : DevelopCombination.c, Task = RscMgr
     88:   140.914 [STARTUP] ERROR ASSERT : Line 108
     89:   140.964 [STARTUP] ERROR ASSERT : FALSE
     90:   141.046 [STARTUP] ASSERT Time 1899/12/31 0:0:0 

Code: [Select]
Sun Aug 28 00:11:48 2016
      0:    11.807 [STARTUP]
K287 ICU Firmware Version 1.1.1 ( 3.3.7 )
      1:    11.875 [STARTUP]
ICU Release DateTime 2012.05.14 13:18:25
      2:    12.221 [SEQ] CreateSequencer (Startup, Num = 6)
      3:    12.491 [SEQ] NotifyComplete (Cur = 0, 0x10000, Flag = 0x10000)
      4:    14.241 [SEQ] seqEventDispatch (Startup, 0)
      5:    14.274 [STARTUP] startupEntry
      6:    52.343 [PROPST] Initialize Adjective & Situation
      7:    52.724 [HPD] # 1 0 1
      8:    56.299 [PROPST] Clear Adjective & Situation (StartupCondition)
      9:    56.712 [PROPST] AEMode New:2 Last:0
     10:    56.810 [PROPST] Active Adjective & Situation
     11:    56.931 [PROPST] ReqChangeCBR : Adjective 0, 0
     12:    56.971 [PROPST] Not ExecMultiConvert Already None : Adjective 0, 0
     13:    57.054 [PROPST] Not ExecMultiConvert : Situation 0
     14:    57.117 [PROPST]  CurrentAdjective 0 0
     15:    58.697 [SEQ] NotifyComplete (Cur = 1, 0x20000002, Flag = 0x2)
     16:    59.789 [PROPST] AEMode New:2 Last:2
     17:    60.649 [PRP] Deliv WaitID = 0x80000001, 0xFF1B8BF8(1)
     18:    62.279 [PRP] Complete WaitID = 0x80000001, 0xFF1B8BF8(0)
     19:    62.505 [PRP] SpecialComplete ID = 0x80000001, 0x80000001 1034
     20:    64.021 [PRP] MovieParamData
     21:    64.268 [PRP] mode 0 size 0x22 , framerate 0x0 , type 0x0 zoom 0x0
     22:    67.016 [PROPST] AEMode New:7 Last:2
     23:    67.078 [PROPST] FromSaveTimming = 2(489)
     24:    71.795 [HPD] CreateTask Master End
     25:    73.356 [EM] emSlaveChangeCBR : AUTO_POWEROFF (1)
     26:    73.517 [EM] emSlaveChangeCBR : UILOCK (0x0)
     27:    74.035 [HPD] ERASE SW OFF
     28:   112.424 [PRP] MovieParamData
     29:   112.749 [PRP] mode 0 size 0x0 , framerate 0x19 , type 0xc zoom 0x0
     30:   118.605 [STARTUP] startupPropAdminMain : End
     31:   118.693 [SEQ] NotifyComplete (Cur = 1, 0x20000000, Flag = 0x20000000)
     32:   118.791 [SEQ] seqEventDispatch (Startup, 1)
     33:   118.824 [STARTUP] startupPrepareProperty
     34:   119.251 [FM] FM_Initialize (0, 1, 0)
     35:   119.676 [FM] fmResultCBR (0x80e408)
     36:   120.648 [FM] PROP_HDD_DCIM_PATH (/)
     37:   120.872 [FC] FC_Initialize [drive:3][ClassID:39]
     38:   121.120 [FM] PROP_CARD1_STATUS = 0x1
     39:   121.256 [FM] PROP_CARD1_FOLDER_NUMBER = 142
     40:   121.368 [FM] PROP_CARD1_FILE_NUMBER = 0
     41:   121.526 [FM] PROP_CARD2_STATUS = 0x0
     42:   121.637 [FM] PROP_CARD2_FOLDER_NUMBER = 100
     43:   121.750 [FM] PROP_CARD2_FILE_NUMBER = 8524
     44:   121.873 [FM] PROP_CARD3_EXIST = 0
     45:   121.936 [FM] PROP_CARD3_STATUS = 0x1
     46:   122.002 [FM] PROP_CARD3_RECORD = 0 => 1
     47:   122.062 [FM] PROP_CARD3_FOLDER_NUMBER = 100
     48:   122.155 [FM] PROP_CARD3_FILE_NUMBER = 0
     49:   122.290 [FM] PROP_FILE_NUMBERING_MODE = 1, 0
     50:   122.357 [FM] PROP_CARD_EXTENSION = 0
     51:   122.421 [FM] PROP_CURRENT_MEDIA = 2
     52:   122.481 [FM] PROP_USBDEVICE_CONNECT = -1
     53:   122.552 [FM] PROP_NUMBER_OF_CONTINUOUS_MODE = 8524
     54:   122.591 [SEQ] NotifyComplete (Cur = 2, 0x10, Flag = 0x10)
     55:   122.721 [FM] PROP_DSDEFINE ModelId 80000287
     56:   122.807 [SEQ] seqEventDispatch (Startup, 2)
     57:   122.833 [STARTUP] startupPrepareCapture
     58:   123.467 [RSC] hMemoryQueue (0x620010) hStorageQueue (0x640012)
     59:   125.147 [RSC] AllocateMemoryUnit For ExMem1
     60:   125.175 [RSC] AllocateMemoryUnit For ExMem1_2
     61:   125.195 [RSC] AllocateMemoryUnit For OnlyMem1
     62:   126.460 [RSC] MemMgr(IMAGE) 0 2
     63:   126.490 [RSC] MemMgr(IMAGE) 0 0
     64:   126.516 [RSC] MemMgr(IMAGE) 0 7
     65:   126.539 [RSC] MemMgr(IMAGE) 0 0
     66:   126.605 [RSC] PROP_MEMORY_STATUS(SELF) (0->)3 (OTHER) 3
     67:   126.623 [RSC] Deliver PROP_MEMORY_STATUS 3
     68:   128.011 [RSC] SRMExMem1_1State Event 0 Result State 0->6
     69:   128.063 [RSC] hExMem1_2StateObject Through Event 0 State 0
     70:   128.793 [RSC] SRMExMem1_1State Event 4 Result State 6->6
     71:   128.828 [RSC] hExMem1_2StateObject Through Event 4 State 0
     72:   129.615 [RSC] this->dwCardStatus[0] = 0x1(552)
     73:   130.362 [RSC] this->dwCardStatus[1] = 0x0(552)
     74:   131.092 [RSC] this->dwCardStatus[2] = 0x1(552)
     75:   131.804 [RSC] PROP_PC_HDD_STATUS = 0x1
     76:   132.722 [RSC] NO IMAGEFORMAT EstimatedSize.c 0
     77:   132.754 [RSC] NO IMAGEFORMAT EstimatedSize.c 0
     78:   132.791 [RSC] ERROR SetDevelopImageCondition DevelopCombination.c 107
     79:   133.916 [RTC] !! RTC CHECK ERROR !!

     80:   138.045 [PRP] Deliv WaitID = 0x8000003F, 0xFF02BE84(1)
     81:   138.278 [EM] emRegisterMulticastCallback : EventID = 14, ClassID = 128
     82:   138.494 [EM] emRegisterMulticastCallback : EventID = 15, ClassID = 128
     83:   138.699 [EM] emRegisterMulticastCallback : EventID = 4, ClassID = 128
     84:   140.000 [JOB] InitializeJobClass (ID = 9699, Num = 17)
     85:   140.283 [JOB] [BIND] dcsResultCBR (0x931ba4)
     86:   140.552 [JOB] PROP_CFN_TAB2 3 0
     87:   140.834 [STARTUP] ERROR ASSERT : DevelopCombination.c, Task = RscMgr
     88:   140.914 [STARTUP] ERROR ASSERT : Line 108
     89:   140.964 [STARTUP] ERROR ASSERT : FALSE
     90:   141.046 [STARTUP] ASSERT Time 1899/12/31 0:0:0
     91:   141.547 [PRP] propRegisterSlave 0x8000003F

     92:   144.120 [STARTUP] startupErrorRequestChangeCBR (0x1d)
     93:   144.244 [STARTUP] startupErrorRequestChangeCBR : ErrorSend (101, ABORT)
     94:   144.520 [PRP] Complete WaitID = 0x8000003F, 0xFF02A10C(1)
     95:   144.846 [CERES]  RegisterGPSInfoCallback
     96:   145.555 [EM] emLockControl (TYPE_JOBSTATE = 0x0)
     97:   146.825 [JOB] InitializeInnerDevelopJobClass (ID = 9699, Num = 16)
     98:   146.868 [JOB] InitializeMultipleExposureSaveAndEndJobClass ( Num = 10 )
     99:   148.315 [SND] Seq LPC 5-0
    100:   148.362 [SND]  HARB_ARBMODE  Before:0x00000000 Current:0x00000000
    101:   148.402 [SND]  HARB_HARBCTRL Before:0x002AEAA8 Current:0x002AEAA8
    102:   148.415 [SND] Seq LPC 5-1
    103:   148.520 [SND] Seq LPC 5-2
    104:   148.592 [SND] Seq LPC 5-3
    105:   148.619 [SND] Seq LPC 5-4
    106:   148.633 [SND] Seq LPC 5-5
    107:   148.673 [SND] Seq LPC 5-6
    108:   149.075 [SND] Seq LPC 5-7
    109:   149.093 [SND] Seq LPC fin
    110:   151.546 [SEQ] NotifyComplete (Cur = 3, 0xe0110, Flag = 0x40000)
    111:   151.764 [EM] emRegisterMulticastCallback : EventID = 14, ClassID = 147
    112:   152.011 [EM] emRegisterMulticastCallback : EventID = 2, ClassID = 147
    113:   152.221 [EM] emRegisterMulticastCallback : EventID = 3, ClassID = 147
    114:   152.432 [EM] emRegisterMulticastCallback : EventID = 15, ClassID = 147
    115:   152.634 [EM] emRegisterMulticastCallback : EventID = 5, ClassID = 147
    116:   152.835 [EM] emRegisterMulticastCallback : EventID = 6, ClassID = 147
    117:   153.043 [EM] emRegisterMulticastCallback : EventID = 1, ClassID = 147
    118:   153.244 [EM] emRegisterMulticastCallback : EventID = 4, ClassID = 147
    119:   153.449 [EM] emRegisterMulticastCallback : EventID = 8, ClassID = 147
    120:   153.656 [EM] emRegisterMulticastCallback : EventID = 9, ClassID = 147
    121:   153.862 [EM] emRegisterMulticastCallback : EventID = 10, ClassID = 147
    122:   154.080 [EM] emRegisterMulticastCallback : EventID = 17, ClassID = 147
    123:   154.321 [SHTC] scsInit
    124:   155.430 [ENG] [ENGIO](Addr:0x5c880000, Data:0x   30000)
    125:   162.008 [SEQ] NotifyComplete (Cur = 3, 0xa0110, Flag = 0x80000)
    126:   162.232 [SHTB] sbsInit
    127:   162.482 [SHTB] VShadingAddress:0x5c8c9960, Size:901120
    128:   163.294 [SHTP] spsInit
    129:   163.401 [FM] FM_RegisterSpaceNotifyCallback
    130:   163.575 [MRK] RegisterSpaceNotifyCallback : DriveNo = 2
    131:   163.615 [FM] voiRegisterSpaceNotifyCallback : DriveNo = 2
    132:   163.674 [FM] RegisterSpaceNotifyCallback : DriveNo = 2
    133:   163.712 [FC] FcmcRegisterSpaceNotifyCallback : DriveNo = 2
    134:   163.768 [FM] FM_RegisterSpaceNotifyCallback
    135:   164.035 [SEQ] NotifyComplete (Cur = 3, 0x20110, Flag = 0x100)
    136:   164.192 [WFT]  TOM_Initialize
    137:   165.015 [EM] emRegisterMulticastCallback : EventID = 0, ClassID = 158
    138:   165.257 [EM] emRegisterMulticastCallback : EventID = 1, ClassID = 158
    139:   165.475 [EM] emRegisterMulticastCallback : EventID = 4, ClassID = 158
    140:   166.243 [EM] emRegisterMulticastCallback : EventID = 0, ClassID = 167
    141:   166.474 [EM] emRegisterMulticastCallback : EventID = 11, ClassID = 167
    142:   166.519 [EM] Already SW1OFF
    143:   166.664 [MC] cam event metering timer start
    144:   166.869 [EM] emRegisterMulticastCallback : EventID = 7, ClassID = 167
    145:   167.076 [EM] emRegisterMulticastCallback : EventID = 1, ClassID = 167
    146:   167.283 [EM] emRegisterMulticastCallback : EventID = 4, ClassID = 167
    147:   167.496 [EM] emRegisterMulticastCallback : EventID = 3, ClassID = 167
    148:   167.718 [EM] emRegisterMulticastCallback : EventID = 2, ClassID = 167
    149:   167.934 [EM] emRegisterMulticastCallback : EventID = 18, ClassID = 131
    150:   168.150 [EM] emRegisterMulticastCallback : EventID = 19, ClassID = 131
    151:   168.905 [EM] emRegisterMulticastCallback : EventID = 13, ClassID = 167
    152:   169.039 [TA10] TA10_Initialize : Start
    153:   169.640 [TA10] TA10S_Initialize : Start
    154:   169.678 [TA10] TA10S_Initialize : CreateStageClass
    155:   169.991 [TA10] TA10S_Initialize : End
    156:   170.168 [TA10] TA10_Initialize : End
    157:   170.315 [FM] fmInitialized
    158:   170.424 [FC] _FC_SetDirSuffix (CANON)
    159:   170.602 [FC] _FC_SetConsecutiveMode (mode = 1, DCF = 8524)
    160:   170.765 [FM] fmPrepare
    161:   172.826 [FM] ALV_Initialize (36, 25)
    162:   173.207 [FM] fmAllocDcfNo(0x80e1c4)(0x0)
    163:   176.831 [TERM] terminateChangeCBR : SHUTDOWN (255)
    164:   176.864 [TERMINATE] SHUTDOWN init comp
    165:   177.027 [TERM] terminateChangeCBR : AUTO_POWEROFF (1)
    166:   177.073 [TERMINATE] Abort init comp
    167:   177.480 [WFT]  PROP_WFT_IMAGE_TRANS (1)
    168:   179.365 [MC] PROP_DISPLAY_OFF_SENSOR : 1
    169:   179.643 [MC] DisplaySensor : 1(0)
    170:   180.410 [MC] PROP_GUI_STATE 0
    171:   180.657 [MC] PROP_LV_ACTION : LV_STOP
    172:   180.807 [MC] PROP_LV_DISPBUSY : not Busy
    173:   181.013 [MC] PROP_LV_LOCK : LVLOCK_PERMIT
    174:   181.171 [MC] PROP_DISABLE_PLAY_IMAGE : Enable Play
    175:   181.626 [MC] JobState 0
    176:   182.693 [MC] QRTime : 2
    177:   183.261 [MC] PROP_VARIANGLE_GUICTRL : Enable
    178:   183.683 [MC] regist master CardCover
    179:   184.770 [PRP] propRegisterSlave 0x8000003F

    180:   185.008 [TA10] ta10_ChangePropCBR ShotsPlan 2 / TotalSheets 2
    181:   186.213 [MC] GuiGroundState : 0
    182:   186.687 [MC] PROP_LV_ACTION : LV_STOP
    183:   187.433 [PRP] Complete WaitID = 0x8000003F, 0xFF080794(1)
    184:   187.708 [MC] Disp Error : 70

syifaa diding

  • Just arrived
  • *
  • Posts: 1
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #106 on: December 05, 2016, 09:38:54 PM »
Dear ALEX, I need help with my Canon 60D camera. The screen shows an error 70, told to turn off and turn on the camera and reinsert the battery. The only way this works is in C, and even then I had to wear full auto mode used to initiate the turn on the camera, half Shuter Biltz open up new switch to the c in order to light up. after burning in the on mode can only be used in that fashion, I try switching to another mode will reappear on the mode c error 70. I have successfully installed the ML, but to turn on the camera is still the same. there are reports of "Crash" in the memory card containing: assert: FALSE
at DevelopCombination.c: 108, task RscMgr
lv: 0 mode: 0


Magic Lantern version: Nightly.2016Nov17.60D111
Mercurial changeset: d5e2cc0b6743 (unified) tip
Built on 2016-11-16 23:14:18 UTC by Jenkins @ nightly.
Free Memory: 390K + 1872K

my email : syifaaphotography@yahoo.co.id

denejka

  • Just arrived
  • *
  • Posts: 1
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #107 on: December 13, 2016, 07:39:54 PM »
Have my bricked 500D (water damaged but it worked fine). Seeing ERROR70 on boot.
I can't have the log files, 'cus I didn't had ML installed (JUST DELETED IT BEFORE THE "DEATH" sadly)
Can I please get some heeeelp?
Using firmware (1.1.1) / Don't have ML (deleted it before death, fu...)
Tried:
1) Booting up in all modes - no effect
2) Changed battery - brighter sd light :)
3) Changed lenses - no effect
4) Formated SD card - no effect

Can I somehow forceinstall ML without going into menu and have autoexec with disabled assert handler?

It's sad that I can't even see logs or get into menu → settings → reset to factory settings
What should I do? Please somebody help me! :C

email: denejka1337@gmail.com

shoegirl

  • Just arrived
  • *
  • Posts: 1
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #108 on: March 20, 2017, 06:59:30 AM »
I have error code 70 as well, nothing helps :(... please send me exe file too.
ktrepchina@gmail.com

aiminli

  • Just arrived
  • *
  • Posts: 1
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #109 on: August 10, 2017, 10:00:15 PM »
Hello,

My Canon 60D has a similar problem like others. The camera worked fine until it was stored in a wet camera bag after which the error 70 prevented using it. It displays error 70 on all shooting modes except the "C"/"CA" trick. First I have to turn the shooting mode to "CA" , power on then power off, change shooting mode to "C" and power on. I was wondering if someone could give me a modified autoexec.bin with disabled assert handler to unbrick the camera. The crash log file is as follows:

ASSERT: FALSE
at DevelopCombination.c:108, task RscMgr
lv:0 mode:0

RscMgr stack: 115e68 [115f90-114f90]
0xUNKNOWN  @ ff07b8cc:115f88
0xUNKNOWN  @ ff1dcb80:115f60
0xFF1DC5DC @ ff02c3fc:115f28
0xUNKNOWN  @ ff1dc60c:115f18
0xUNKNOWN  @ ff1dc694:115ef8
0xFF0CAE58 @ ff0c992c:115ec0
0xFF013EC0 @ ff0caf18:115ea0
0x1FE00368 @ 1fe006d0:115e68

Magic Lantern version : Nightly.2017Aug07.60D111
Mercurial changeset   : ff6f36e11acb (unified) tip
Built on 2017-08-06 22:14:23 UTC by jenkins@nightly.
Free Memory  : 390K + 1920K

My Canon firmware version is 1.1.1.
Email: aimin.mn@gmail.com
Thanks.

The log002.log is as follows:

Code: [Select]
Wed Aug  9 18:07:49 2017
      0:    11.809 [STARTUP]
K287 ICU Firmware Version 1.1.1 ( 3.3.7 )
      1:    11.875 [STARTUP]
ICU Release DateTime 2012.05.14 13:18:25
      2:    12.221 [SEQ] CreateSequencer (Startup, Num = 6)
      3:    12.488 [SEQ] NotifyComplete (Cur = 0, 0x10000, Flag = 0x10000)
      4:    14.252 [SEQ] seqEventDispatch (Startup, 0)
      5:    14.279 [STARTUP] startupEntry
      6:    52.611 [PROPST] Initialize Adjective & Situation
      7:    53.010 [HPD] # 1 0 1
      8:    56.499 [PROPST] Clear Adjective & Situation (StartupCondition)
      9:    56.903 [PROPST] AEMode New:0 Last:0
     10:    57.000 [PROPST] Active Adjective & Situation
     11:    57.118 [PROPST] ReqChangeCBR : Adjective 0, 0
     12:    57.156 [PROPST] Not ExecMultiConvert Already None : Adjective 0, 0
     13:    57.246 [PROPST] Not ExecMultiConvert : Situation 0
     14:    57.316 [PROPST]  CurrentAdjective 0 0
     15:    58.849 [HPD] CreateTask Master End
     16:    60.513 [EM] emSlaveChangeCBR : AUTO_POWEROFF (1)
     17:    60.673 [EM] emSlaveChangeCBR : UILOCK (0x0)
     18:    61.160 [HPD] ERASE SW OFF
     19:   111.029 [STARTUP] startupPropAdminMain : End
     20:   111.107 [SEQ] NotifyComplete (Cur = 1, 0x20000002, Flag = 0x20000000)
     21:   155.773 [SEQ] NotifyComplete (Cur = 1, 0x2, Flag = 0x2)
     22:   156.353 [PROPST] AEMode New:0 Last:0
     23:   156.779 [PRP] Deliv WaitID = 0x80000001, 0xFF1B8BF8(1)
     24:   157.551 [PRP] Complete WaitID = 0x80000001, 0xFF1B8BF8(0)
     25:   157.628 [PRP] SpecialComplete ID = 0x80000001, 0x80000001 1034
     26:   158.173 [SEQ] seqEventDispatch (Startup, 1)
     27:   158.211 [STARTUP] startupPrepareProperty
     28:   158.374 [PRP] MovieParamData
     29:   158.513 [PRP] mode 0 size 0x0 , framerate 0x1e , type 0xf zoom 0x0
     30:   161.355 [FM] FM_Initialize (0, 1, 0)
     31:   161.906 [FM] fmResultCBR (0x80e4a4)
     32:   163.177 [FM] PROP_HDD_DCIM_PATH (/)
     33:   163.789 [PROPST] AEMode New:2 Last:0
     34:   164.170 [PRP] Complete WaitID = 0x8000003F, 0x00000000(0)
     35:   164.427 [FC] FC_Initialize [drive:3][ClassID:39]
     36:   164.783 [FM] PROP_CARD1_STATUS = 0x1
     37:   164.923 [FM] PROP_CARD1_FOLDER_NUMBER = 142
     38:   165.025 [FM] PROP_CARD1_FILE_NUMBER = 0
     39:   165.179 [FM] PROP_CARD2_STATUS = 0x1
     40:   165.280 [FM] PROP_CARD2_FOLDER_NUMBER = 100
     41:   165.391 [FM] PROP_CARD2_FILE_NUMBER = 3268
     42:   165.513 [FM] PROP_CARD3_EXIST = 0
     43:   165.571 [FM] PROP_CARD3_STATUS = 0x1
     44:   165.637 [FM] PROP_CARD3_RECORD = 0 => 0
     45:   165.700 [FM] PROP_CARD3_FOLDER_NUMBER = 100
     46:   165.789 [FM] PROP_CARD3_FILE_NUMBER = 0
     47:   165.904 [FM] PROP_FILE_NUMBERING_MODE = 1, 0
     48:   165.976 [FM] PROP_CARD_EXTENSION = 132
     49:   166.043 [FM] PROP_CURRENT_MEDIA = 2
     50:   166.111 [FM] PROP_USBDEVICE_CONNECT = -1
     51:   166.183 [FM] PROP_NUMBER_OF_CONTINUOUS_MODE = 3268
     52:   166.223 [SEQ] NotifyComplete (Cur = 2, 0x10, Flag = 0x10)
     53:   166.356 [FM] PROP_DSDEFINE ModelId 80000287
     54:   166.445 [SEQ] seqEventDispatch (Startup, 2)
     55:   166.469 [STARTUP] startupPrepareCapture
     56:   167.135 [RSC] hMemoryQueue (0x620010) hStorageQueue (0x640012)
     57:   168.880 [RSC] AllocateMemoryUnit For ExMem1
     58:   168.905 [RSC] AllocateMemoryUnit For ExMem1_2
     59:   168.924 [RSC] AllocateMemoryUnit For OnlyMem1
     60:   170.211 [RSC] MemMgr(IMAGE) 0 2
     61:   170.252 [RSC] MemMgr(IMAGE) 0 0
     62:   170.279 [RSC] MemMgr(IMAGE) 0 7
     63:   170.303 [RSC] MemMgr(IMAGE) 0 0
     64:   170.370 [RSC] PROP_MEMORY_STATUS(SELF) (0->)3 (OTHER) 3
     65:   170.391 [RSC] Deliver PROP_MEMORY_STATUS 3
     66:   170.932 [RSC] SRMExMem1_1State Event 0 Result State 0->6
     67:   170.970 [RSC] hExMem1_2StateObject Through Event 0 State 0
     68:   171.587 [RSC] SRMExMem1_1State Event 4 Result State 6->6
     69:   171.617 [RSC] hExMem1_2StateObject Through Event 4 State 0
     70:   172.365 [RSC] this->dwCardStatus[0] = 0x1(552)
     71:   173.096 [RSC] this->dwCardStatus[1] = 0x1(552)
     72:   173.806 [RSC] this->dwCardStatus[2] = 0x1(552)
     73:   174.522 [RSC] PROP_PC_HDD_STATUS = 0x1
     74:   175.485 [RSC] NO IMAGEFORMAT EstimatedSize.c 10
     75:   175.519 [RSC] NO IMAGEFORMAT EstimatedSize.c 10
     76:   175.555 [RSC] ERROR SetDevelopImageCondition DevelopCombination.c 107
     77:   176.744 [RTC] !! RTC CHECK ERROR !!

     78:   179.916 [EM] emRegisterMulticastCallback : EventID = 14, ClassID = 128
     79:   180.150 [EM] emRegisterMulticastCallback : EventID = 15, ClassID = 128
     80:   180.357 [EM] emRegisterMulticastCallback : EventID = 4, ClassID = 128
     81:   181.563 [JOB] InitializeJobClass (ID = 25253, Num = 17)
     82:   181.888 [JOB] [BIND] dcsResultCBR (0x931b20)
     83:   182.155 [JOB] PROP_CFN_TAB2 10 10
     84:   183.694 [STARTUP] ERROR ASSERT : DevelopCombination.c, Task = RscMgr
     85:   183.780 [STARTUP] ERROR ASSERT : Line 108
     86:   183.828 [STARTUP] ERROR ASSERT : FALSE
     87:   183.917 [STARTUP] ASSERT Time 1899/12/31 0:0:0
     88:   185.346 [STARTUP] startupErrorRequestChangeCBR (0x1d)
     89:   185.476 [STARTUP] startupErrorRequestChangeCBR : ErrorSend (101, ABORT)
     90:   185.928 [CERES]  RegisterGPSInfoCallback
     91:   186.653 [EM] emLockControl (TYPE_JOBSTATE = 0x0)
     92:   187.924 [JOB] InitializeInnerDevelopJobClass (ID = 25253, Num = 16)
     93:   187.996 [JOB] InitializeMultipleExposureSaveAndEndJobClass ( Num = 10 )
     94:   189.526 [SND] Seq LPC 5-0
     95:   189.571 [SND]  HARB_ARBMODE  Before:0x00000000 Current:0x00000000
     96:   189.609 [SND]  HARB_HARBCTRL Before:0x002AEAA8 Current:0x002AEAA8
     97:   189.621 [SND] Seq LPC 5-1
     98:   189.677 [SND] Seq LPC 5-2
     99:   189.720 [SND] Seq LPC 5-3
    100:   189.773 [SND] Seq LPC 5-4
    101:   189.786 [SND] Seq LPC 5-5
    102:   189.798 [SND] Seq LPC 5-6
    103:   190.206 [SND] Seq LPC 5-7
    104:   190.220 [SND] Seq LPC fin
    105:   192.219 [SEQ] NotifyComplete (Cur = 3, 0xe0110, Flag = 0x40000)
    106:   192.400 [EM] emRegisterMulticastCallback : EventID = 14, ClassID = 147
    107:   192.659 [EM] emRegisterMulticastCallback : EventID = 2, ClassID = 147

topandrajat

  • Just arrived
  • *
  • Posts: 1
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #110 on: December 28, 2017, 12:56:34 PM »
Hi a1ex ....
I apologize for my bad language.

Dear a1ex, I have the same problem, but with a 600D canon that is error 70: and now can not be used to take a picture when the button is on tap.
Can you share the modified autoexec from "a1ex" and full instructions how to use it?
My email add irfaklahumu@gmail.com

here is my last Log:

Code: [Select]
Thu Dec 28 17:41:38 2017
      0:     9.225 [STARTUP]
K286 ICU Firmware Version 1.0.2 ( 3.8.3 )
      1:     9.290 [STARTUP]
ICU Release DateTime 2011.11.25 11:00:17
      2:    11.209 [SEQ] seqEventDispatch (Startup, 0)
      3:    11.240 [STARTUP] startupEntry
      4:   112.868 [STARTUP] startupPropAdminMain : End
      5:   112.986 [SEQ] seqEventDispatch (Startup, 1)
      6:   113.017 [STARTUP] startupPrepareProperty
      7:   116.036 [SEQ] seqEventDispatch (Startup, 2)
      8:   116.660 [RSC] hMemoryQueue (0x620010) hStorageQueue (0x640012)
      9:   135.638 [JOB] InitializeJobClass (ID = 39461, Num = 16)
     10:   137.418 [CERES]  RegisterGPSInfoCallback
     11:   138.038 [EM] emLockControl (TYPE_JOBSTATE = 0x0)
     12:   140.487 [JOB] InitializeInnerDevelopJobClass (ID = 39461, Num = 16)
     13:   140.521 [JOB] InitializeMultipleExposureSaveAndEndJobClass ( Num = 10 )
     14:   142.236 [SND] Seq LPC fin
     15:   146.038 [ENG] [ENGIO](Addr:0x4fb40000, Data:0x   30000)
     16:   153.226 [FM] FM_RegisterSpaceNotifyCallback
     17:   153.424 [FM] FM_RegisterSpaceNotifyCallback
     18:   155.698 [TERMINATE] SHUTDOWN init comp
     19:   155.784 [TERMINATE] Abort init comp
     20:   156.018 [WFT]  PROP_WFT_IMAGE_TRANS (1)
     21:   161.910 [MC] PROP_GUI_STATE 0
     22:   162.252 [MC] JobState 0
     23:   163.343 [MC] PROP_LCD_OFFON_BUTTON : 0
     24:   163.644 [MC] PROP_VARIANGLE_GUICTRL : Enable
     25:   165.091 [MC] regist master CardCover
     26:   166.014 [WFT]  tomSetRawJpgMode (Type = 0x4)
     27:   166.148 [SHTP] spsInit
     28:   169.591 [FM] fmPrepare : Completed
     29:   169.862 [SEQ] seqEventDispatch (Startup, 3)
     30:   172.693 [PRP] M:50 F:0 L:0 P:1B T:1
     31:   173.017 [STARTUP] internal version 03:08:03:00:50:00:00:1b
     32:   174.165 [STARTUP] startupPrepareDevelop
     33:   174.535 [SHTFD] sdsInit
     34:   174.861 [SHTRD] sdsInit
     35:   174.998 [SHTFD] sdsActivate
     36:   180.124 [SHTRD] sdsActivate
     37:   183.303 [SHTP] spsActivate
     38:   198.414 [SHTP] Regist RPC Handler Master ALO
     39:   256.276 [MR] mvrChangeAckCBR : Video - Mode=0, Type=0, Rate=25, GOP=12
     40:   256.396 [MR] mvrChangeAckCBR : Sound Auto(C=2,R=48000,B=16)
     41:   256.436 [MR] mvrChangeAckCBR : AE_MODE_MOVIE(0)
     42:   256.459 [MR] mvrChangeAckCBR : ISO(0)
     43:   256.567 [MR] mvrChangeAckCBR : MOVIE_REC_VOLUME(L:47 R:47)
     44:   256.638 [MR] mvrChangeAckCBR : WindCut Off
     45:   267.469 [LV] [GMT] PROP_TEMP_STATUS : STATUS_NORMAL
     46:   274.926 [HPC] ReserveHPCopySingleChannel (2, 117)
     47:   275.227 [LV] InitializeLiveViewDefectDetection
     48:   308.953 [MD] Init RCh1=0, RCh2=0
     49:   309.657 [MD] Set RCh1=d, RCh2=18
     50:   310.160 [STARTUP] startupPrepareRemote
     51:   320.360 [PTP] Not Setting CFn MirrorUpState
     52:   320.758 [PTP] PhotoStudioMode:0
     53:   322.782 [PTP] PROP_OPTICAL_CORRECT_PARAM Size:1aeb0 f3c
     54:   334.373 [RMT] PROP_CONNECT_TARGET (0x0 <= 0x0)
     55:   334.737 [MAC] MAC_Initialize
     56:   335.200 [MAC] K_BOARDID4
     57:   335.271 [MAC] K_BOARDID3
     58:   335.333 [MAC] K_BOARDID2
     59:   335.396 [MAC] K_BOARDID1
     60:   335.722 [MAC] Key=0x6 Board=0x651a1a87 Body=0x89945146
     61:   336.173 [PTP] PSI DisconnectViewFinder
     62:   336.509 [PTP] PROP_CONNECT_TARGET (0x0 <= 0x0)
     63:   336.664 [PTP] PROP_CONNECT_TARGET_WFT (0x0 <= 0x0)
     64:   337.636 [MAGIC] SetPtpTransportResources:0,3218
     65:   837.493 [SD] CARD CAPACITY is 30346Mbyte( 62148608Sec )
     66:   860.793 [SD] SD_GetAccessMode=3
     67:   875.442 [FM] FileNo (DriveNo = 2, 0 <-> 7692)
     68:   875.553 [FM] FreeCluster (DriveNo = 2, 969443 <-> 969444)
     69:   876.386 [FC] _FC_OpenCatalog : wNumOfDir 1
     70:   886.052 [SEQ] seqEventDispatch (Startup, 4)
     71:   886.386 [DP] DP_Initialize()
     72:   887.712 [DP] Std T_PrintPage[0] T_PrintNo[0] R_PrintNo[0]
     73:   887.776 [DP] Std C_PrintNo[0] C_PrintPage[0], C_Copies[0]
     74:   887.910 [DP] Dp_SetPD_RegistApi Prev:0 New:0
     75:   888.390 [DP] PROP_CONNECT_TARGET [0x00000000]
     76:   888.603 [DP] RD_Cancel No Issue
     77:   889.018 [DP] [GYO]DpFunctionList[0x10117fff]
     78:   889.176 [DP] X FreeMem Address[0x00000000]
     79:   889.683 [INDEV] INDEV_Initialize
     80:   926.616 [IMPP] H264E InitializeH264EncodeFor1080pDZoom
     81:   926.739 [IMPP] H264E InitializeH264EncodeFor1080p25fpsDZoom
     82:   949.194 [MR_MOV] (Empty Func) MVW_RegisterXmpDataCallback
     83:   950.595 [HDMI] HPD OFF
     84:   950.695 [HDMI] [EDID] dwVideoCode = 0
     85:   950.754 [HDMI] [EDID] dwHsize = 0
     86:   950.805 [HDMI] [EDID] dwVsize = 0
     87:   950.851 [HDMI] [EDID] ScaningMode = EDID_NON_INTERLACE(p)
     88:   950.897 [HDMI] [EDID] VerticalFreq = EDID_FREQ_60Hz
     89:   950.940 [HDMI] [EDID] AspectRatio = EDID_ASPECT_4x3
     90:   950.989 [HDMI] [EDID] AudioMode = 0
     91:   951.029 [HDMI] [EDID] ColorMode = EDID_COLOR_RGB
     92:   951.268 [HDMI] DisconnectHDMI : Not Connected
     93:   953.960 [STARTUP] TotalSizeOfMemory : 0x8b0000 (8896KB)
     94:   954.074 [STARTUP] GetFreeSizeOfMemory : 0x172c14 (1483KB)
     95:   954.274 [STARTUP] GetSizeOfMaxRegion : 0x16d980 (1462KB)
     96:   975.331 WARN [LVDS] First Get DTS_GetAllRandomData
     97:   978.149 [DP] DP_RegisterCBR() Id=1 Count:12
     98:   978.213 [DP] DP_RegisterCBR() Id=2 Count:12
     99:   978.252 [DP] DP_RegisterCBR() Id=4 Count:12
    100:   989.884 [GUI] MainEventHandler PROP_QR_DIDNOT_EXECUTE(0)(0)
    101:   991.748 [GUI] MainEventHandler PROP_ERROR_FOR_DISPLAY(0)
    102:   992.994 [DISP] UpdateReverseTFT(off) Current=0 Target=1
    103:  1006.022 [SEQ] seqEventDispatch (Startup, 5)
    104:  1006.058 [STARTUP] startupInitializeComplete
    105:  1006.202 [MC] cam event guimode comp. 0
    106:  1009.681 [FA] ChangeCBR(ID=0x8003000a)
    107:  1012.611 [FA] RequestFromCheckData
    108:  1013.036 [FA] MpuMonSpecificFromPartner : COM_FA_CHECK_FROM 0
    109:  1019.898 [DISP] UpdateReverseTFT(off) Current=1 Target=1
    110:  1030.758 [DISP] UpdateReverseTFT(off) Current=1 Target=1
    111:  1054.755 [MR] mvrChangeAckCBR : Video - Mode=0, Type=0, Rate=25, GOP=12
    112:  1056.011 [GUI] MainEventHandler PROP_LV_OUTPUT_DEVICE(0)
    113:  1057.602 [MC] cam event guimode comp. 0
    114:  1061.638 [MR] mvrChangeAckCBR : Video - Mode=0, Type=0, Rate=25, GOP=12
    115:  1067.833 [SEQ] seqEventDispatch (Startup) : End
    116:  1114.358 [DISP] UpdateReverseTFT(off) Current=1 Target=1
    117:  1138.039 [WINSYS] Zlib maxsize update 884
    118:  1138.120 [WINSYS] Zlib maxsize update 1396
    119:  1293.216 [DISP] UpdateReverseTFT(off) Current=1 Target=1
    120:  1331.282 [DISP] Enable Pb 1 (2149)
    121:  1457.097 [DISP] TurnOnDisplay finish Type=0
    122:  1945.048 [PTP] ptpDpsCtginfoCheckCompleteCBR[42][0][2]
    123:  2550.971 [DISP] UpdateReverse Current=1 Target=1
    124:  4485.129 WARN [LVDS] First Get DTS_GetAllRandomData
    125:  4486.006 [LV] [PATH] GetPathDriveInfo[0]
    126:  4486.414 WARN [LVDS] First Get DTS_GetAllRandomData
    127:  4486.956 WARN [LVDS] First Get DTS_GetAllRandomData
    128:  4489.267 [CAPD] ImagePowerOn
    129:  4490.017 WARN [LVDS] First Get DTS_GetAllRandomData
    130:  4490.137 WARN [LVDS] First Get DTS_GetAllRandomData
    131:  4497.005 WARN [LVDS] First Get DTS_GetAllRandomData
    132:  4504.689 [CAPD] ERROR [LV] Image Power Failure
    133:  4505.056 [STARTUP] startupErrorRequestChangeCBR (0x82218001)
    134:  4505.140 [STARTUP] startupErrorRequestChangeCBR : ErrorSend (120, SHUTDOWN)
    135:  4508.423 WARN [LVDS] First Get DTS_GetAllRandomData
    136:  4508.510 [LV] [EVF] ShootingMode(2), FrameRate(5)
    137:  4508.542 [LV] [EVF] Flicker Detect!!!
    138:  4547.171 [DISP] Disable Pb 0 (2078)
    139:  4547.249 [DISP] TurnOffDisplay finish Type=0
    140:  4550.899 [LV] [EVF] evfComAct(1) is not Complete
    141:  4551.310 [LVP] ERROR [VRAM] ####RamClear Clear####
    142:  4552.147 [CAPD] ImagePowerOff
    143:  4563.449 [DISP] UpdateReverseTFT(off) Current=1 Target=1
    144:  4601.746 [GUI] MainEventHandler PROP_LV_OUTPUT_DEVICE(1)
    145:  4749.437 [STARTUP] DispError 70 ERROR Time 2017/12/28 17:41:38
    146:  4749.612 [MC] Disp Error : 70
    147:  4769.526 [DISP] UpdateReverseTFT(off) Current=1 Target=1
    148:  4797.041 [DISP] Enable Pb 1 (2149)
    149:  4802.212 [PTP] PSI DisconnectViewFinder
    150:  4927.023 [DISP] TurnOnDisplay finish Type=0
    151:  5027.082 [DISP] Disable Pb 0 (2078)
    152:  5027.193 [DISP] TurnOffDisplay finish Type=0
    153:  5027.471 [DISP] UpdateReverseTFT(off) Current=1 Target=1
    154:  5064.336 [GUI] MainEventHandler PROP_ERROR_FOR_DISPLAY(70)
    155:  5067.075 [GUI] MainEventHandler PROP_LV_OUTPUT_DEVICE(0)
    156:  5067.809 [GUI] ERROR ***** handleDispsensorCtrl TFTOLC_CTRL_STATE_SYSTEM_ERROR
    157:  5068.429 [GUI] IDLEHandler START_WARNING_CAMERA_ERR
    158:  5097.921 [DISP] UpdateReverseTFT(off) Current=1 Target=1
 

i really hope your help a1ex....
thanks a1ex ;)

tobiasBora

  • New to the forum
  • *
  • Posts: 8
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #111 on: July 30, 2021, 09:54:42 AM »
My turn to try to solve the Error 70 on Canon 60D! My case seems to be a bit different (sorry if this is not appropriate for this thread): basically, for no apparent reason, my Canon 60D started to have this error 70 a few seconds after a boot (I see during 2 seconds the number of left images etc... on the small top LCD screen, then I've this error), and at the same time the backlight of my main LCD screen stopped working completely (using a lamp I can manage to see some stuff written on the screen and navigate into the menu, even if it's quite hard to read). However, I can still manage to take some pictures: I need to half-press during a few seconds the button which takes pictures, and the error usually disappears during a few seconds, giving me some time to focus & take the actual picture. However, it's highly not practical, and since I don't have any backlight, I can't checked the final photo I took.

I tried to reset (thanks my lamp!) the camera settings via the menu, but it does not change anything. I tried to use another SD card, and tried to format this other card using gparted. Same error.

ML does not gives me much error (most of the time, it does not even mention the error 70). On this log (coming from a file logXXX.log, I don't have any crash file), I just turned on the camera, observed the error 70 during maybe 2 seconds, and then I half-pressed the button to take a picture: the error was gone for about 1 second and appeared again (note that "nano" displays also an invisible char ^@ at the beginning of each line):

Code: [Select]
Fri Jul 30 09:21:23 2021
     0:    11.811 [STARTUP]
K287 ICU Firmware Version 1.1.1 ( 3.3.7 )
     1:    11.884 [STARTUP]
ICU Release DateTime 2012.05.14 13:18:25
     2:    12.231 [SEQ] CreateSequencer (Startup, Num = 6)
     3:    12.497 [SEQ] NotifyComplete (Cur = 0, 0x10000, Flag = 0x10000)
     4:    14.355 [SEQ] seqEventDispatch (Startup, 0)
     5:    14.387 [STARTUP] startupEntry
     6:    51.536 [PROPST] Initialize Adjective & Situation
     7:    51.874 [HPD] # 1 1 0
     8:    54.808 [PROPST] Clear Adjective & Situation (StartupCondition)
     9:    55.270 [PROPST] AEMode New:2 Last:0
    10:    55.356 [PROPST] Active Adjective & Situation
    11:    55.462 [PROPST] ReqChangeCBR : Adjective 0, 0
    12:    55.498 [PROPST] Not ExecMultiConvert Already None : Adjective 0, 0
    13:    55.565 [PROPST] Not ExecMultiConvert : Situation 0
    14:    55.623 [PROPST]  CurrentAdjective 0 0
    15:    56.430 [HPD] Variangle State 2
    16:    56.984 [HPD] CreateTask Master End
    17:    57.883 [SEQ] NotifyComplete (Cur = 1, 0x20000002, Flag = 0x2)
    18:    58.799 [PROPST] AEMode New:2 Last:2
    19:    59.532 [PRP] Deliv WaitID = 0x80000001, 0xFF1B8BF8(1)
    20:    60.390 [PRP] Complete WaitID = 0x80000001, 0xFF1B8BF8(0)
    21:    60.550 [PRP] SpecialComplete ID = 0x80000001, 0x80000001 1034
    22:    61.486 [PRP] MovieParamData
    23:    61.674 [PRP] mode 0 size 0x0 , framerate 0x1e , type 0xf zoom 0x0
    24:    65.093 [EM] emSlaveChangeCBR : AUTO_POWEROFF (1)
    25:    65.283 [EM] emSlaveChangeCBR : UILOCK (0x0)
    26:    65.772 [HPD] ERASE SW OFF
    27:    77.777 [PRP] Complete WaitID = 0x8000003F, 0x00000000(0)
    28:   112.534 [STARTUP] startupPropAdminMain : End
    29:   112.606 [SEQ] NotifyComplete (Cur = 1, 0x20000000, Flag = 0x20000000)
    30:   112.684 [SEQ] seqEventDispatch (Startup, 1)
    31:   112.711 [STARTUP] startupPrepareProperty
    32:   113.065 [FM] FM_Initialize (0, 1, 0)
    33:   113.426 [FM] fmResultCBR (0x80e2a8)
    34:   113.914 [FM] PROP_HDD_DCIM_PATH (/)
    35:   114.095 [FC] FC_Initialize [drive:3][ClassID:39]
    36:   114.297 [FM] PROP_CARD1_STATUS = 0x1
    37:   114.383 [FM] PROP_CARD1_FOLDER_NUMBER = 142
    38:   114.444 [FM] PROP_CARD1_FILE_NUMBER = 0
    39:   114.531 [FM] PROP_CARD2_STATUS = 0x0
    40:   114.596 [FM] PROP_CARD2_FOLDER_NUMBER = 100
    41:   114.655 [FM] PROP_CARD2_FILE_NUMBER = 5226
    42:   114.722 [FM] PROP_CARD3_EXIST = 0
    43:   114.759 [FM] PROP_CARD3_STATUS = 0x1
    44:   114.799 [FM] PROP_CARD3_RECORD = 0 => 1
    45:   114.839 [FM] PROP_CARD3_FOLDER_NUMBER = 100
    46:   114.884 [FM] PROP_CARD3_FILE_NUMBER = 0
    47:   114.940 [FM] PROP_FILE_NUMBERING_MODE = 1, 0
    48:   114.975 [FM] PROP_CARD_EXTENSION = 0
    49:   115.008 [FM] PROP_CURRENT_MEDIA = 2
    50:   115.038 [FM] PROP_USBDEVICE_CONNECT = -1
    51:   115.076 [FM] PROP_NUMBER_OF_CONTINUOUS_MODE = 5226
    52:   115.110 [SEQ] NotifyComplete (Cur = 2, 0x10, Flag = 0x10)
    53:   115.202 [FM] PROP_DSDEFINE ModelId 80000287
    54:   115.265 [SEQ] seqEventDispatch (Startup, 2)
    55:   115.287 [STARTUP] startupPrepareCapture
    56:   115.872 [RSC] hMemoryQueue (0x620010) hStorageQueue (0x640012)
    57:   117.186 [RSC] AllocateMemoryUnit For ExMem1
    58:   117.208 [RSC] AllocateMemoryUnit For ExMem1_2
    59:   117.226 [RSC] AllocateMemoryUnit For OnlyMem1
    60:   118.005 [RSC] MemMgr(IMAGE) 0 2
    61:   118.033 [RSC] MemMgr(IMAGE) 0 0
    62:   118.052 [RSC] MemMgr(IMAGE) 0 7
    63:   118.068 [RSC] MemMgr(IMAGE) 0 0
    64:   118.125 [RSC] PROP_MEMORY_STATUS(SELF) (0->)3 (OTHER) 3
    65:   118.141 [RSC] Deliver PROP_MEMORY_STATUS 3
    66:   118.627 [RSC] SRMExMem1_1State Event 0 Result State 0->6
    67:   118.659 [RSC] hExMem1_2StateObject Through Event 0 State 0
    68:   119.166 [RSC] SRMExMem1_1State Event 4 Result State 6->6
    69:   119.197 [RSC] hExMem1_2StateObject Through Event 4 State 0
    70:   119.918 [RSC] this->dwCardStatus[0] = 0x1(552)
    71:   120.567 [RSC] this->dwCardStatus[1] = 0x0(552)
    72:   121.204 [RSC] this->dwCardStatus[2] = 0x1(552)
    73:   121.833 [RSC] PROP_PC_HDD_STATUS = 0x1
    74:   122.700 [RSC] SRMExMem1_1State Event 4 Result State 6->6
    75:   122.734 [RSC] hExMem1_2StateObject Through Event 4 State 0
    76:   123.467 [RSC] SRMExMem1_1State Event 4 Result State 6->6
    77:   123.496 [RSC] hExMem1_2StateObject Through Event 4 State 0
    78:   124.229 [RSC] SRMExMem1_1State Event 4 Result State 6->6
    79:   124.264 [RSC] hExMem1_2StateObject Through Event 4 State 0
    80:   125.373 [RSC] SRMExMem1_1State Event 4 Result State 6->6
    81:   125.408 [RSC] hExMem1_2StateObject Through Event 4 State 0
    82:   126.049 [RSC] PC_STORAGE_SLOT STORAGE_NOT_EXIST
    83:   126.082 [RSC] PROP_SAVE_MODE = 0x1
    84:   126.306 [RSC] PROP_CARD0_FOLDER_NUMBER
    85:   126.493 [RSC] PROP_CARD1_FOLDER_NUMBER
    86:   126.664 [RSC] PROP_CARD2_FOLDER_NUMBER
    87:   127.196 [RSC] PROP_NUMBER_OF_CONTINUOUS_MODE BaseDcfNo 5226
    88:   128.311 [RSC] RearrangeMemMgr 0 1
    89:   129.400 [RSC] PROP_CARD_EXTENSION 0
    90:   130.726 [RSC] PC_CLUSTER_SIZE = 0x1000
    91:   131.143 [RSC] PROP_CFN_TAB2 ST_MEM_MAP_NORMAL->ST_MEM_MAP_NORMAL
    92:   131.207 [RSC] ClearBusy(0x1000) 0x40->0x40,0x0(0x40)[0,0]
    93:   131.549 [RSC] SetAutoIsoCode 0x70
    94:   131.587 [RSC] ChangeAutoIsoCode Factor:1 AutoIsoCode:112 -> 112
    95:   131.803 [RSC] SetAutoIsoCode 0x70
    96:   131.836 [RSC] ChangeAutoIsoCode Factor:2 AutoIsoCode:112 -> 112
    97:   132.213 [RSC] ClearBusy(0x40000) 0x40->0x40,0x0(0x40)[0,0]
    98:   132.452 [RSC] ClearBusy(0x40000) 0x40->0x40,0x0(0x40)[0,0]
    99:   132.668 [RSC] ClearBusy(0x40000) 0x40->0x40,0x0(0x40)[0,0]
   100:   132.855 [RSC] ClearBusy(0x40000) 0x40->0x40,0x0(0x40)[0,0]
   101:   133.014 [RSC] SetAutoIsoCode 0x70
   102:   133.039 [RSC] ChangeAutoIsoCode Factor:0 AutoIsoCode:112 -> 112
   103:   133.419 [EM] emRegisterMulticastCallback : EventID = 14, ClassID = 128
   104:   133.552 [EM] emRegisterMulticastCallback : EventID = 15, ClassID = 128
   105:   133.666 [EM] emRegisterMulticastCallback : EventID = 4, ClassID = 128
   106:   134.147 [RSC] SetBusy(0x10) 0x40->0x50,0x0(0x50)[0,0]
   107:   134.178 [RSC] RealSetBusy(0x10) 0x40->0x50,0x0(0x50)
   108:   134.448 [JOB] InitializeJobClass (ID = 16196, Num = 17)
   109:   134.635 [JOB] [BIND] dcsResultCBR (0x930ea8)
   110:   134.778 [JOB] PROP_CFN_TAB2 0 0
   111:   135.788 [CERES]  RegisterGPSInfoCallback
   112:   136.258 [EM] emLockControl (TYPE_JOBSTATE = 0x0)
   113:   136.518 [RSC] SRMExMem1_1State Event 6 Result State 6->6
   114:   136.554 [RSC] hExMem1_2StateObject Through Event 6 State 0
   115:   137.166 [Burst0] 589823 4 44 44 16772618
   116:   137.597 [RSC] PROP_SAVE_MODE = 0x1
   117:   137.735 [Burst0] 589823 4 44 44 16772618
   118:   138.853 [JOB] InitializeInnerDevelopJobClass (ID = 16196, Num = 16)
   119:   138.884 [JOB] InitializeMultipleExposureSaveAndEndJobClass ( Num = 10 )
   120:   140.068 [SND] Seq LPC 5-0
   121:   140.110 [SND]  HARB_ARBMODE  Before:0x00000000 Current:0x00000000
   122:   140.144 [SND]  HARB_HARBCTRL Before:0x002AEAA8 Current:0x002AEAA8
   123:   140.153 [SND] Seq LPC 5-1
   124:   140.208 [SND] Seq LPC 5-2
   125:   140.248 [SND] Seq LPC 5-3
   126:   140.294 [SND] Seq LPC 5-4
   127:   140.305 [SND] Seq LPC 5-5
   128:   140.316 [SND] Seq LPC 5-6
   129:   140.704 [SND] Seq LPC 5-7
   130:   140.719 [SND] Seq LPC fin
   131:   141.867 [SEQ] NotifyComplete (Cur = 3, 0xe0110, Flag = 0x40000)
   132:   142.076 [EM] emRegisterMulticastCallback : EventID = 14, ClassID = 147
   133:   142.257 [EM] emRegisterMulticastCallback : EventID = 2, ClassID = 147
   134:   142.421 [EM] emRegisterMulticastCallback : EventID = 3, ClassID = 147
   135:   142.575 [EM] emRegisterMulticastCallback : EventID = 15, ClassID = 147
   136:   142.715 [EM] emRegisterMulticastCallback : EventID = 5, ClassID = 147
   137:   142.879 [EM] emRegisterMulticastCallback : EventID = 6, ClassID = 147
   138:   143.006 [EM] emRegisterMulticastCallback : EventID = 1, ClassID = 147
   139:   143.144 [EM] emRegisterMulticastCallback : EventID = 4, ClassID = 147
   140:   143.278 [EM] emRegisterMulticastCallback : EventID = 8, ClassID = 147
   141:   143.424 [EM] emRegisterMulticastCallback : EventID = 9, ClassID = 147
   142:   143.566 [EM] emRegisterMulticastCallback : EventID = 10, ClassID = 147
   143:   143.703 [EM] emRegisterMulticastCallback : EventID = 17, ClassID = 147
   144:   143.887 [SHTC] scsInit
   145:   144.860 [ENG] [ENGIO](Addr:0x5c880000, Data:0x   30000)
   146:   150.948 [SEQ] NotifyComplete (Cur = 3, 0xa0110, Flag = 0x80000)
   147:   151.132 [SHTB] sbsInit
   148:   151.350 [SHTB] VShadingAddress:0x5c8c9960, Size:901120
   149:   152.068 [SHTP] spsInit
   150:   152.154 [FM] FM_RegisterSpaceNotifyCallback
   151:   152.278 [MRK] RegisterSpaceNotifyCallback : DriveNo = 2
   152:   152.310 [FM] voiRegisterSpaceNotifyCallback : DriveNo = 2
   153:   152.365 [FM] RegisterSpaceNotifyCallback : DriveNo = 2
   154:   152.398 [FC] FcmcRegisterSpaceNotifyCallback : DriveNo = 2
   155:   152.420 [FM] FM_RegisterSpaceNotifyCallback
   156:   152.668 [SEQ] NotifyComplete (Cur = 3, 0x20110, Flag = 0x100)
   157:   152.779 [WFT]  TOM_Initialize
   158:   154.063 [TERM] terminateChangeCBR : SHUTDOWN (255)
   159:   154.088 [TERMINATE] SHUTDOWN init comp
   160:   154.155 [TERM] terminateChangeCBR : AUTO_POWEROFF (1)
   161:   154.176 [TERMINATE] Abort init comp
   162:   154.343 [WFT]  PROP_WFT_IMAGE_TRANS (1)
   163:   155.651 [SHTC] Mem1Component Size=0x37a54
   164:   156.347 [SHTC] DarkcurAddress:0x5c9a5960, Size:131072
   165:   156.446 [SHTC] scsProperty ID=0x0(0x80)
   166:   156.500 [SHTC] scsProperty ID=0x80040004(0x0)
   167:   156.612 [RSC] ClearBusy(0x40) 0x50->0x10,0x0(0x10)[0,0]
   168:   157.143 [EM] emRegisterMulticastCallback : EventID = 0, ClassID = 158
   169:   157.302 [EM] emRegisterMulticastCallback : EventID = 1, ClassID = 158
   170:   157.427 [EM] emRegisterMulticastCallback : EventID = 4, ClassID = 158
   171:   158.741 [EM] emRegisterMulticastCallback : EventID = 0, ClassID = 167
   172:   158.890 [EM] emRegisterMulticastCallback : EventID = 11, ClassID = 167
   173:   158.920 [EM] Already SW1OFF
   174:   159.018 [MC] cam event metering timer start
   175:   159.130 [EM] emRegisterMulticastCallback : EventID = 7, ClassID = 167
   176:   159.239 [EM] emRegisterMulticastCallback : EventID = 1, ClassID = 167
   177:   159.344 [EM] emRegisterMulticastCallback : EventID = 4, ClassID = 167
   178:   159.491 [EM] emRegisterMulticastCallback : EventID = 3, ClassID = 167
   179:   159.625 [EM] emRegisterMulticastCallback : EventID = 2, ClassID = 167
   180:   159.729 [EM] emRegisterMulticastCallback : EventID = 18, ClassID = 131
   181:   159.832 [EM] emRegisterMulticastCallback : EventID = 19, ClassID = 131
   182:   160.252 [MC] PROP_DISPLAY_OFF_SENSOR : 1
   183:   160.389 [MC] DisplaySensor : 1(0)
   184:   160.842 [MC] PROP_GUI_STATE 0
   185:   160.989 [MC] PROP_LV_ACTION : LV_STOP
   186:   161.068 [MC] PROP_LV_DISPBUSY : not Busy
   187:   161.146 [MC] PROP_LV_LOCK : LVLOCK_PERMIT
   188:   161.229 [MC] PROP_DISABLE_PLAY_IMAGE : Enable Play
   189:   161.315 [MC] JobState 0
   190:   161.499 [RSC] ClearBusy(0x20000) 0x10->0x10,0x0(0x10)[0,0]
   191:   162.054 [MC] QRTime : 2
   192:   162.310 [DISP] WARN ForceBackLightOff before initialize !!
   193:   162.473 [MC] PROP_VARIANGLE_GUICTRL : Enable
   194:   162.682 [MC] GuiGroundState : 0
   195:   162.930 [MC] PROP_LV_ACTION : LV_STOP
   196:   163.188 [MC] PROP_VARIANGLE_GUICTRL : Disable
   197:   164.035 [MC] regist master CardCover
   198:   164.212 [EM] emRegisterMulticastCallback : EventID = 13, ClassID = 167
   199:   164.296 [TA10] TA10_Initialize : Start
   200:   165.722 [TA10] ta10_ChangePropCBR ShotsPlan 2 / TotalSheets 2
   201:   167.259 [TA10] TA10S_Initialize : Start
   202:   167.298 [TA10] TA10S_Initialize : CreateStageClass
   203:   167.530 [TA10] TA10S_Initialize : End
   204:   167.631 [TA10] TA10_Initialize : End
   205:   167.734 [FM] fmInitialized
   206:   167.801 [FC] _FC_SetDirSuffix (CANON)
   207:   167.856 [FC] _FC_SetConsecutiveMode (mode = 1, DCF = 5226)
   208:   167.937 [FM] fmPrepare
   209:   168.459 [WFT]  tomSetRawJpgMode (Type = 0x4)
   210:   169.468 [FM] ALV_Initialize (36, 25)
   211:   169.735 [FM] fmAllocDcfNo(0x80e064)(0x0)
   212:   169.927 [RSC] srmAllocDcfNoTable
   213:   169.974 [FM] fmAllocateDcfNoCompleteCallback(0x5c710000,0x4000)
   214:   170.263 [FM] fmAllocDcfNo : DcfNoTable(0x5c710000)
   215:   170.462 [SD] ---- SDEventHandler(ID=1:Event=8) ----
   216:   375.006 [SD] sdTrySendCommand1: Timeout
   217:   562.914 [SD] sdSendOCR: Hi-Capacity Card
   218:   564.130 [SD] sdSendOCR: Hi-Capacity Card
   219:   565.330 [SD] sdSendOCR: Hi-Capacity Card
   220:   566.508 [SD] sdSendOCR: Hi-Capacity Card
   221:   569.260 [SD] CsdStructVersion = 1
   222:   569.285 [SD] MMCSpecVersion = 0
   223:   569.319 [SD] C_SIZE=0x0001dbd3 READ_BL_LEN=0x0009
   224:   569.335 [SD] *** EraseBlks = 128 ***
   225:   569.367 [SD] CARD CAPACITY is 60906Mbyte( 124735488Sec )
   226:   570.475 [SD] sdSendCID: MID = 0x03, PDN = 0x5352
   227:   577.896 [SD] sdSendStatus: SD_CARD_TYPE_H  = 0x0000
   228:   577.917 [SD] sdSendStatus: SD_CARD_TYPE_L  = 0x0000
   229:   581.413 [SD] sdSendSCR: SCR=0x87844502, SpecVersion=2
   230:   587.375 [SD] sdSwitchFunction( 0 ) Status=0x80000003, AccessMode=3
   231:   588.013 [SD] Support Hi Speed Mode
   232:   593.928 [SD] sdSwitchFunction( 1 ) Status=0x80000003, AccessMode=3
   233:   594.634 [SD] nBlocks=124735488, blksPerTrack=0, nHeads=0
   234:   594.654 [SD] ERASE_TIMEOUT:1
   235:   594.664 [SD] ERASE_OFFSET:1
   236:   594.676 [SD] ERASE_SIZE:f
   237:   594.685 [SD] AU_SIZE:9
   238:   594.702 [SD] dwEraseSectorSize:128
   239:   594.719 [SD] dwEraseBlks:2000 CSD:1
   240:   594.743 [SD] SD_GetAccessMode=3
   241:   594.754 [SD] Set Hi-Speed Mode( 48MHz )
   242:   628.109 [FM] EV_INSERTION_COMPLETE : ID = 2, stat = 0
   243:   628.265 [FM] fmNormalMountCard (ID = 2, Ret = 0)
   244:   628.288 [FM] fmPrepareShooting (Drive = 2)
   245:   628.360 [FC] _FC_PrepareCatalog (2, B:)
   246:   629.700 [SD] ---- SDEventHandler(ID=1:< B: >) Mounted ----
   247:   652.225 [FM] DirNo = 100, FileNo = 5218
   248:   661.054 [FM] Cluster = 131072, Total = 486992, Free = 84374
   249:   661.121 [FC] _FC_GetNewDirDcfNo (2, 0, 0, 0)
   250:   661.164 [FM] fmSetInitialCardInfo (Drive = 2, 0)
   251:   662.319 [RSC] PROP_CARD1_FOLDER_NUMBER
   252:   662.811 [RSC] this->dwCardStatus[1] = 0x1(552)
   253:   664.121 [RSC] Storage Space 84374
   254:   664.558 [FM] pfNotifyDcfNoCBR(2:100_5218)
   255:   664.733 [RSC] srmNotifyDcfNo 0x2 100 5218 0 1
   256:   664.770 [RSC] srmSetDcfNoTableOrDiff 1 100 5218 1
   257:   664.787 [RSC] Diff Dcf List
   258:   664.804 [RSC] Create Diff Dcf ListItem 100
   259:   664.839 [RSC] fTemporary 1 pMaxDcfNoInFolder->fTemporary 1
   260:   664.856 [RSC] Diff Dcf Over Write 100
   261:   664.907 [RSC] ####### [1]DCF No 5226
   262:   665.272 [RSC] BURST 48 Enable 1353 Reserve 8159232
   263:   665.340 [RSC] Burst 48 ENABLE 1353 Reserve 8159232
   264:   665.385 [RSC] ClearBusy(0x2100) 0x10->0x10,0x0(0x10)[0,0]
   265:   665.430 [SEQ] NotifyComplete (Cur = 3, 0x20010, Flag = 0x20000)
   266:   666.239 [SEQ] NotifyComplete (Cur = 3, 0x10, Flag = 0x10)
   267:   666.415 [FM] PROP_CARD2_FOLDER_NUMBER = 100
   268:   666.471 [FM] PROP_CARD2_STATUS = 0x1
   269:   666.563 [FM] PROP_CARD2_FILE_NUMBER = 5226
   270:   666.718 [SEQ] seqEventDispatch (Startup, 3)
   271:   666.877 [RSC] RealClearBusy(0x10) 0x10->0x0,0x0(0x0)
   272:   667.296 [PROPST] PROP_PERMIT_ICU_EVENT 0x0
   273:   668.015 [RSC] SRMExMem1_1State Event 4 Result State 6->6
   274:   668.137 [RSC] hExMem1_2StateObject Through Event 4 State 0
   275:   669.124 [RSC] RealClearBusy(0x2100) 0x0->0x0,0x0(0x0)
   276:   669.605 [PRP] M:6C F:0 L:0 P:2F
   277:   669.903 [STARTUP] internal version 03:03:07:00:6c:00:00:2f
   278:   670.501 [STARTUP] startupPrepareDevelop
   279:   670.889 [SHTFD] sdsInit
   280:   671.545 [SHTRD] sdsInit
   281:   671.666 [SHTP] spsActivate
   282:   686.876 [SHTP] Regist RPC Handler Master ALO
   283:   687.062 [SHTFD] sdsActivate
   284:   690.589 [SHTRD] sdsActivate
   285:   691.793 < GUI Lock > InitializeGUILock (PUB)
   286:   692.246 [GUI] MasterResultCBR
   287:   692.435 [AUDIO] InitializeAudioIC
   288:   692.542 [AUDIO] micResultCBR
   289:   692.603 [AUDIO] micDetectAckCBR�F0
   290:   692.805 [AUDIO] EnableAudioIC
   291:   692.834 [AUDIO] Reg(0x05) Data(0x0023)
   292:   692.959 [AUDIO] Reg(0x00) Data(0x0040)
   293:   693.033 [AUDIO] Reg(0x01) Data(0x0003)
   294:   693.094 [AUDIO] Reg(0x02) Data(0x0000)
   295:   693.147 [AUDIO] Reg(0x04) Data(0x006a)
   296:   693.235 [AUDIO] Reg(0x0E) Data(0x0091)
   297:   693.304 [AUDIO] Reg(0x0F) Data(0x0008)
   298:   693.364 [AUDIO] Reg(0x07) Data(0x0007)
   299:   693.417 [AUDIO] Reg(0x06) Data(0x0064)
   300:   693.469 [AUDIO] Reg(0x08) Data(0x00d2)
   301:   693.519 [AUDIO] Reg(0x09) Data(0x00d2)
   302:   693.569 [AUDIO] Reg(0x0C) Data(0x00d2)
   303:   693.619 [AUDIO] Reg(0x0A) Data(0x0090)
   304:   693.668 [AUDIO] Reg(0x25) Data(0x0090)
   305:   693.718 [AUDIO] Reg(0x0B) Data(0x0080)
   306:   693.767 [AUDIO] Reg(0x11) Data(0x0000)
   307:   694.025 [AUDIO] InitializeASIF�FPriority(23)
   308:   694.058 [AUDIO] EnableASIF
   309:   694.072 [AUDIO] WaitPllLockComplete
   310:   694.172 [FM] PROP_CURRENT_MEDIA = 2
   311:   733.254 [AUDIO] _PllLockTimeout
   312:   733.510 [AUDIO] InitializeSoundDevice
   313:   733.837 [SND] NRbuffer:0x009A1A6C
   314:   733.877 [MR_MOV] MOVW_Initialize
   315:   734.197 [MR] MVR_Initialize
   316:   734.541 [MR] mvrResultCBR : 0x9b6fe0
   317:   734.635 [MR] mvrChangeAckCBR : PROP_USBDEVICE_CONNECT(-1)
   318:   734.693 [MR] mvrChangeAckCBR : Video - Mode=0, Type=0, Rate=30, GOP=15
   319:   734.783 [MR] mvrChangeAckCBR : Sound Auto(C=2,R=48000,B=16)
   320:   734.813 [MR] mvrChangeAckCBR : AE_MODE_MOVIE(0)
   321:   734.832 [MR] mvrChangeAckCBR : ISO(0)
   322:   734.910 [MR] mvrChangeAckCBR : MOVIE_REC_VOLUME(L:47 R:47)
   323:   734.954 [MR] mvrChangeAckCBR : WindCut Off
   324:   735.496 [MP] MVP_Initialize (44, 22)
   325:   736.015 [MP_MOV] MOVR_InitializeMovReader (45, 23)
   326:   737.970 [EM] emRegisterMulticastCallback : EventID = 1, ClassID = 152
   327:   738.124 [EM] emRegisterMulticastCallback : EventID = 4, ClassID = 152
   328:   738.238 [EM] emRegisterMulticastCallback : EventID = 18, ClassID = 152
   329:   738.351 [EM] emRegisterMulticastCallback : EventID = 19, ClassID = 152
   330:   741.775 [LV] [GMT] PROP_AE_MODE:2
   331:   741.882 [LV] [GMT][WAKU] gmtChangeLensMFFace (state:0)
   332:   742.691 [LV] [GMT] PROP_TEMP_STATUS : STATUS_NORMAL
   333:   742.997 [LV] [GMT] gmtIgnore (state:0)
   334:   743.021 [LV] [GMT] PROP_SHOOTING_TYPE 0
   335:   743.348 [LV] [GMT] PROP_VIDEO_PHYSICAL_CONNECT:0x00000000
   336:   743.432 [LV] [GMT] PROP_HDMI_PHYSICAL_CONNECT:0x00000000
   337:   743.773 [LV] [GMT] PROP_LIVE_VIEW_FACE_AF
   338:   744.058 [LV] [GMT][WAKU] gmtSelAFModeLiveFromFace (state:7)
   339:   744.113 [LV] [GMT][WAKU] gmtUpdateFrameWithModeChange (state:7 mani:21)
   340:   744.238 [LV] [GMT] gmtSaveModeEvent state:0
   341:   744.394 [LV] [GMT] PROP_MOVIE_PARAM Mode:0, R(2->2), SC(0->0) SZ(0->0)
   342:   744.413 [LV] [GMT] PROP_MOVIE_PARAM DZ(0->0)
   343:   744.543 [LV] [GMT] PROP_LIVE_VIEW_VIEWTYPE_SELECT:1
   344:   745.052 [LV] [GMT][WAKU] gmtDispSize (state:7)
   345:   745.256 [LV] [GMT] PROP_AE_MODE_MOVIE:0
   346:   745.305 [LV] [GMT] PROP_AUTO_ISO_RANGE:Max(70)Min(48)
   347:   745.345 [LV] [GMT] PROP_MOVIE_REC_AF:(0)
   348:   745.386 [LV] [GMT] SPECIAL_OPTION_LVAE_GERO_MODE:0x00000000
   349:   745.503 [LV] PROP_LV_CONTINUOUS_RESULT
   350:   745.545 [LV] [GMT] PROP_IMAGE_ASPECT_RATIO: 0
   351:   745.573 [LV] [GMT][WAKU] gmtUpdateFrame (state:7) fModeChange:0
   352:   745.679 [LV] [GMT] gmtChangeAvailableArea state:0
   353:   745.826 [LV] PROP_LV_IMAGE_HANDLE_FOR_MULTIPLE_EXPOSURE:00000000
   354:   745.903 [LV] PROP_MULTIPLE_EXPOSURE_CURRENT_SHOTS 0
   355:   745.946 [LV] PROP_MULTIPLE_EXPOSURE_SETTING AUTOGAIN:1
   356:   745.961 [LV] PROP_MULTIPLE_EXPOSURE_SETTING:0
   357:   746.035 [LV] [GMT] gmtInit
   358:   746.117 [LV] [GMT] gmtStart:0x2
   359:   746.684 [LV] [GMT][WAKU] GMT_WAKU_Initialize
   360:   746.762 [LV] [GMT] gmtChangeAvailableArea state:1
   361:   747.314 [LV] [EVF] evfInit
   362:   748.147 [LV] [PATH] ClearRam::0x409bd200
   363:   748.164 [LV] [PATH] ResLock CreateLock[20] OK
   364:   748.318 [HPC] ReserveHPCopySingleChannel (2, 117)
   365:   748.485 [LV] [PATH] Flicker_GetPathParameter(1148)
   366:   748.607 [LV] InitializeLiveViewDefectDetection
   367:   749.280 [ENG] LockEng   [0x97645c][Evf]
   368:   749.412 [ENGP] [DEFM] WrAddr(CH=3)=0x1f788780
   369:   749.501 [ENGP] [DEFM] RdAddr(CH=10)=0x7d2f5c
   370:   749.544 [ENGP] [DEFM] RdAddr(CH=11)=0x5440e4
   371:   749.691 [ENGP] [DEFM] MergeCompleteCBR
   372:   749.746 [ENGP] [DEFM] MergeDefectsCount = 1536
   373:   749.787 [ENGP] [DEFM] Read1AbortCBR
   374:   749.804 [ENGP] [DEFM] Read2AbortCBR
   375:   749.837 [ENGP] [DEFM] Write1PopCBR
   376:   749.980 [ENG] UnLockEng [0x97645c][Evf]
   377:   750.364 [ENG] LockEng   [0x97645c][Evf]
   378:   750.478 [ENGP] [DEFM] WrAddr(CH=3)=0x1f798780
   379:   750.529 [ENGP] [DEFM] RdAddr(CH=10)=0x7d335c
   380:   750.564 [ENGP] [DEFM] RdAddr(CH=11)=0x552b4c
   381:   750.736 [ENGP] [DEFM] MergeCompleteCBR
   382:   750.792 [ENGP] [DEFM] MergeDefectsCount = 9394
   383:   750.839 [ENGP] [DEFM] Read1AbortCBR
   384:   750.858 [ENGP] [DEFM] Read2AbortCBR
   385:   750.889 [ENGP] [DEFM] Write1PopCBR
   386:   751.035 [ENG] UnLockEng [0x97645c][Evf]
   387:   751.438 [ENG] LockEng   [0x97645c][Evf]
   388:   751.550 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7b87b0
   389:   751.603 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3b9c
   390:   751.643 [ENGP] [DEFM] RdAddr(CH=11)=0x5615e4
   391:   751.698 [ENGP] [DEFM] MergeCompleteCBR
   392:   751.748 [ENGP] [DEFM] MergeDefectsCount = 161
   393:   751.779 [ENGP] [DEFM] Read1AbortCBR
   394:   751.798 [ENGP] [DEFM] Read2AbortCBR
   395:   751.831 [ENGP] [DEFM] Write1PopCBR
   396:   751.961 [ENG] UnLockEng [0x97645c][Evf]
   397:   752.273 [ENG] LockEng   [0x97645c][Evf]
   398:   752.379 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7b8a34
   399:   752.434 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3bc4
   400:   752.475 [ENGP] [DEFM] RdAddr(CH=11)=0x561868
   401:   752.528 [ENGP] [DEFM] MergeCompleteCBR
   402:   752.567 [ENGP] [DEFM] MergeDefectsCount = 159
   403:   752.597 [ENGP] [DEFM] Read1AbortCBR
   404:   752.614 [ENGP] [DEFM] Read2AbortCBR
   405:   752.641 [ENGP] [DEFM] Write1PopCBR
   406:   752.766 [ENG] UnLockEng [0x97645c][Evf]
   407:   753.068 [ENG] LockEng   [0x97645c][Evf]
   408:   753.170 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7b8cb0
   409:   753.216 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3bec
   410:   753.259 [ENGP] [DEFM] RdAddr(CH=11)=0x561ae4
   411:   753.309 [ENGP] [DEFM] MergeCompleteCBR
   412:   753.348 [ENGP] [DEFM] MergeDefectsCount = 156
   413:   753.381 [ENGP] [DEFM] Read1AbortCBR
   414:   753.399 [ENGP] [DEFM] Read2AbortCBR
   415:   753.429 [ENGP] [DEFM] Write1PopCBR
   416:   753.546 [ENG] UnLockEng [0x97645c][Evf]
   417:   753.834 [ENG] LockEng   [0x97645c][Evf]
   418:   753.935 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7b8f20
   419:   753.982 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3c14
   420:   754.021 [ENGP] [DEFM] RdAddr(CH=11)=0x561d54
   421:   754.072 [ENGP] [DEFM] MergeCompleteCBR
   422:   754.110 [ENGP] [DEFM] MergeDefectsCount = 200
   423:   754.143 [ENGP] [DEFM] Read1AbortCBR
   424:   754.160 [ENGP] [DEFM] Read2AbortCBR
   425:   754.195 [ENGP] [DEFM] Write1PopCBR
   426:   754.310 [ENG] UnLockEng [0x97645c][Evf]
   427:   754.586 [ENG] LockEng   [0x97645c][Evf]
   428:   754.694 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7b9240
   429:   754.741 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3c3c
   430:   754.784 [ENGP] [DEFM] RdAddr(CH=11)=0x562074
   431:   754.839 [ENGP] [DEFM] MergeCompleteCBR
   432:   754.875 [ENGP] [DEFM] MergeDefectsCount = 145
   433:   754.907 [ENGP] [DEFM] Read1AbortCBR
   434:   754.924 [ENGP] [DEFM] Read2AbortCBR
   435:   754.951 [ENGP] [DEFM] Write1PopCBR
   436:   755.071 [ENG] UnLockEng [0x97645c][Evf]
   437:   755.359 [ENG] LockEng   [0x97645c][Evf]
   438:   755.458 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7b9484
   439:   755.505 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3c64
   440:   755.545 [ENGP] [DEFM] RdAddr(CH=11)=0x5622b8
   441:   755.601 [ENGP] [DEFM] MergeCompleteCBR
   442:   755.641 [ENGP] [DEFM] MergeDefectsCount = 165
   443:   755.670 [ENGP] [DEFM] Read1AbortCBR
   444:   755.689 [ENGP] [DEFM] Read2AbortCBR
   445:   755.718 [ENGP] [DEFM] Write1PopCBR
   446:   755.838 [ENG] UnLockEng [0x97645c][Evf]
   447:   756.124 [ENG] LockEng   [0x97645c][Evf]
   448:   756.233 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7b9718
   449:   756.285 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3c8c
   450:   756.325 [ENGP] [DEFM] RdAddr(CH=11)=0x56254c
   451:   756.376 [ENGP] [DEFM] MergeCompleteCBR
   452:   756.409 [ENGP] [DEFM] MergeDefectsCount = 154
   453:   756.438 [ENGP] [DEFM] Read1AbortCBR
   454:   756.455 [ENGP] [DEFM] Read2AbortCBR
   455:   756.482 [ENGP] [DEFM] Write1PopCBR
   456:   756.605 [ENG] UnLockEng [0x97645c][Evf]
   457:   756.892 [ENG] LockEng   [0x97645c][Evf]
   458:   756.992 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7b9980
   459:   757.044 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3cb4
   460:   757.081 [ENGP] [DEFM] RdAddr(CH=11)=0x5627b4
   461:   757.127 [ENGP] [DEFM] MergeCompleteCBR
   462:   757.163 [ENGP] [DEFM] MergeDefectsCount = 157
   463:   757.195 [ENGP] [DEFM] Read1AbortCBR
   464:   757.211 [ENGP] [DEFM] Read2AbortCBR
   465:   757.240 [ENGP] [DEFM] Write1PopCBR
   466:   757.369 [ENG] UnLockEng [0x97645c][Evf]
   467:   757.656 [ENG] LockEng   [0x97645c][Evf]
   468:   757.756 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7b9bf4
   469:   757.805 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3cdc
   470:   757.846 [ENGP] [DEFM] RdAddr(CH=11)=0x562a28
   471:   757.897 [ENGP] [DEFM] MergeCompleteCBR
   472:   757.933 [ENGP] [DEFM] MergeDefectsCount = 152
   473:   757.964 [ENGP] [DEFM] Read1AbortCBR
   474:   757.980 [ENGP] [DEFM] Read2AbortCBR
   475:   758.011 [ENGP] [DEFM] Write1PopCBR
   476:   758.131 [ENG] UnLockEng [0x97645c][Evf]
   477:   758.423 [ENG] LockEng   [0x97645c][Evf]
   478:   758.526 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7b9e54
   479:   758.573 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3d04
   480:   758.610 [ENGP] [DEFM] RdAddr(CH=11)=0x562c88
   481:   758.664 [ENGP] [DEFM] MergeCompleteCBR
   482:   758.702 [ENGP] [DEFM] MergeDefectsCount = 154
   483:   758.737 [ENGP] [DEFM] Read1AbortCBR
   484:   758.754 [ENGP] [DEFM] Read2AbortCBR
   485:   758.779 [ENGP] [DEFM] Write1PopCBR
   486:   758.898 [ENG] UnLockEng [0x97645c][Evf]
   487:   759.184 [ENG] LockEng   [0x97645c][Evf]
   488:   759.290 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7ba0bc
   489:   759.339 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3d2c
   490:   759.375 [ENGP] [DEFM] RdAddr(CH=11)=0x562ef0
   491:   759.424 [ENGP] [DEFM] MergeCompleteCBR
   492:   759.521 [ENGP] [DEFM] MergeDefectsCount = 157
   493:   759.560 [ENGP] [DEFM] Read1AbortCBR
   494:   759.577 [ENGP] [DEFM] Read2AbortCBR
   495:   759.607 [ENGP] [DEFM] Write1PopCBR
   496:   759.730 [ENG] UnLockEng [0x97645c][Evf]
   497:   760.031 [ENG] LockEng   [0x97645c][Evf]
   498:   760.141 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7ba330
   499:   760.193 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3d54
   500:   760.231 [ENGP] [DEFM] RdAddr(CH=11)=0x563164
   501:   760.292 [ENGP] [DEFM] MergeCompleteCBR
   502:   760.322 [ENGP] [DEFM] MergeDefectsCount = 586
   503:   760.358 [ENGP] [DEFM] Read1AbortCBR
   504:   760.373 [ENGP] [DEFM] Read2AbortCBR
   505:   760.405 [ENGP] [DEFM] Write1PopCBR
   506:   760.534 [ENG] UnLockEng [0x97645c][Evf]
   507:   760.833 [ENG] LockEng   [0x97645c][Evf]
   508:   760.941 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7bbe90
   509:   760.991 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3fcc
   510:   761.031 [ENGP] [DEFM] RdAddr(CH=11)=0x564cc4
   511:   761.083 [ENGP] [DEFM] MergeCompleteCBR
   512:   761.126 [ENGP] [DEFM] MergeDefectsCount = 151
   513:   761.157 [ENGP] [DEFM] Read1AbortCBR
   514:   761.174 [ENGP] [DEFM] Read2AbortCBR
   515:   761.202 [ENGP] [DEFM] Write1PopCBR
   516:   761.324 [ENG] UnLockEng [0x97645c][Evf]
   517:   761.619 [ENG] LockEng   [0x97645c][Evf]
   518:   761.718 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7bc0ec
   519:   761.770 [ENGP] [DEFM] RdAddr(CH=10)=0x7d3ff4
   520:   761.815 [ENGP] [DEFM] RdAddr(CH=11)=0x564f20
   521:   761.865 [ENGP] [DEFM] MergeCompleteCBR
   522:   761.902 [ENGP] [DEFM] MergeDefectsCount = 170
   523:   761.937 [ENGP] [DEFM] Read1AbortCBR
   524:   761.958 [ENGP] [DEFM] Read2AbortCBR
   525:   761.982 [ENGP] [DEFM] Write1PopCBR
   526:   762.100 [ENG] UnLockEng [0x97645c][Evf]
   527:   762.384 [ENG] LockEng   [0x97645c][Evf]
   528:   762.490 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7bc394
   529:   762.544 [ENGP] [DEFM] RdAddr(CH=10)=0x7d401c
   530:   762.586 [ENGP] [DEFM] RdAddr(CH=11)=0x5651c8
   531:   762.636 [ENGP] [DEFM] MergeCompleteCBR
   532:   762.675 [ENGP] [DEFM] MergeDefectsCount = 152
   533:   762.707 [ENGP] [DEFM] Read1AbortCBR
   534:   762.725 [ENGP] [DEFM] Read2AbortCBR
   535:   762.756 [ENGP] [DEFM] Write1PopCBR
   536:   762.871 [ENG] UnLockEng [0x97645c][Evf]
   537:   763.162 [ENG] LockEng   [0x97645c][Evf]
   538:   763.274 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7bc5f4
   539:   763.331 [ENGP] [DEFM] RdAddr(CH=10)=0x7d4044
   540:   763.369 [ENGP] [DEFM] RdAddr(CH=11)=0x565428
   541:   763.420 [ENGP] [DEFM] MergeCompleteCBR
   542:   763.458 [ENGP] [DEFM] MergeDefectsCount = 169
   543:   763.489 [ENGP] [DEFM] Read1AbortCBR
   544:   763.507 [ENGP] [DEFM] Read2AbortCBR
   545:   763.538 [ENGP] [DEFM] Write1PopCBR
   546:   763.663 [ENG] UnLockEng [0x97645c][Evf]
   547:   763.949 [ENG] LockEng   [0x97645c][Evf]
   548:   764.056 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7bc898
   549:   764.105 [ENGP] [DEFM] RdAddr(CH=10)=0x7d406c
   550:   764.144 [ENGP] [DEFM] RdAddr(CH=11)=0x5656cc
   551:   764.192 [ENGP] [DEFM] MergeCompleteCBR
   552:   764.229 [ENGP] [DEFM] MergeDefectsCount = 148
   553:   764.263 [ENGP] [DEFM] Read1AbortCBR
   554:   764.280 [ENGP] [DEFM] Read2AbortCBR
   555:   764.307 [ENGP] [DEFM] Write1PopCBR
   556:   764.432 [ENG] UnLockEng [0x97645c][Evf]
   557:   764.728 [ENG] LockEng   [0x97645c][Evf]
   558:   764.829 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7bcae8
   559:   764.877 [ENGP] [DEFM] RdAddr(CH=10)=0x7d4094
   560:   764.916 [ENGP] [DEFM] RdAddr(CH=11)=0x56591c
   561:   764.967 [ENGP] [DEFM] MergeCompleteCBR
   562:   765.005 [ENGP] [DEFM] MergeDefectsCount = 165
   563:   765.041 [ENGP] [DEFM] Read1AbortCBR
   564:   765.061 [ENGP] [DEFM] Read2AbortCBR
   565:   765.090 [ENGP] [DEFM] Write1PopCBR
   566:   765.213 [ENG] UnLockEng [0x97645c][Evf]
   567:   765.497 [ENG] LockEng   [0x97645c][Evf]
   568:   765.595 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7bcd7c
   569:   765.647 [ENGP] [DEFM] RdAddr(CH=10)=0x7d40bc
   570:   765.681 [ENGP] [DEFM] RdAddr(CH=11)=0x565bb0
   571:   765.733 [ENGP] [DEFM] MergeCompleteCBR
   572:   765.765 [ENGP] [DEFM] MergeDefectsCount = 164
   573:   765.795 [ENGP] [DEFM] Read1AbortCBR
   574:   765.810 [ENGP] [DEFM] Read2AbortCBR
   575:   765.834 [ENGP] [DEFM] Write1PopCBR
   576:   765.966 [ENG] UnLockEng [0x97645c][Evf]
   577:   766.245 [ENG] LockEng   [0x97645c][Evf]
   578:   766.350 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7bd00c
   579:   766.407 [ENGP] [DEFM] RdAddr(CH=10)=0x7d40e4
   580:   766.451 [ENGP] [DEFM] RdAddr(CH=11)=0x565e40
   581:   766.504 [ENGP] [DEFM] MergeCompleteCBR
   582:   766.539 [ENGP] [DEFM] MergeDefectsCount = 157
   583:   766.570 [ENGP] [DEFM] Read1AbortCBR
   584:   766.587 [ENGP] [DEFM] Read2AbortCBR
   585:   766.612 [ENGP] [DEFM] Write1PopCBR
   586:   766.727 [ENG] UnLockEng [0x97645c][Evf]
   587:   767.010 [ENG] LockEng   [0x97645c][Evf]
   588:   767.116 [ENGP] [DEFM] WrAddr(CH=3)=0x1f7bd280

On this one, I played a bit more (I think to remember I took a picture with it), and it displays a bit more errors, like:
Code: [Select]
  1586:  1209.705 [DL ERROR] CommC STATUS1 Irregal!! : 15
  1587:  1209.974 [STARTUP] startupErrorRequestChangeCBR : OverWrite (0x82208101 => 0x8220820`
  [...]
  1596:  1245.150 [STARTUP] DispError 70 ERROR Time 2021/7/30 9:21:14

Full log: https://pastebin.com/ZrcCcHSr

Any idea what I can try? Do you think the screen issue is linked with this error 70?

-- EDIT --
I also tried to install the "Hello world" thing https://www.magiclantern.fm/forum/index.php?topic=14732.0 and it semi-works: the backlight is still broken, but the text is displayed when I use a lamp to read.

names_are_hard

  • Developer
  • Senior
  • *****
  • Posts: 407
  • 200D idiot
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #112 on: July 31, 2021, 03:06:06 PM »
Err 70 is a Canon error code for a wide range of problems, often caused by hardware failure.  You don't say, but I assume you have these problems with or without ML.  If you are using third party hardware (lens, flash etc), try without those attached.

I don't have much experience troubleshooting Canon HW problems, but you seem to have multiple problems at once.  Possibly a loose cable inside?

tobiasBora

  • New to the forum
  • *
  • Posts: 8
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #113 on: July 31, 2021, 04:16:05 PM »
@names_are_hard: Yes I know that Err 70 can be produced by a wide range of problems. I was hopping that the log could help experienced user to determine which ^^' I first got this error with ML, but I then tried to insert an empty SD card in it (without ML), I tried to start with "Set" key enabled, but I never tried to completely uninstall ML (I was thinking that ML could be useful to debug at some point). Do you think it makes sense to uninstall ML completely?

It may be a loose cable, I've no idea... Should I try to open the main LCD screen case following something like that

names_are_hard

  • Developer
  • Senior
  • *****
  • Posts: 407
  • 200D idiot
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #114 on: July 31, 2021, 04:51:59 PM »
I would keep the cam able to run ML, that allows running diagnostic tests.  I read the logs but didn't see anything obvious to me (I don't have experience using these logs to diagnose HW errors, only software).

If you are confident about removing the case to check for loose or disconnected cables, it might help.  If you don't feel comfortable doing this, then don't.

kitor

  • Developer
  • Senior
  • *****
  • Posts: 281
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #115 on: August 02, 2021, 08:53:54 AM »
Quote
I tried to start with "Set" key enabled, but I never tried to completely uninstall ML (I was thinking that ML could be useful to debug at some point).

You don't need to uninstall anything - just put in any freshly formatted (on PC) card instead. "Installation" just flips a software switch that tells the camera OS "pssst, if you see memory card with that special name, try to execute autoexec.bin from there". This is stock firmware functionality that we enable.
No special card = nothing will start which is equivalent to not having ML in the first place.

Quote
I also tried to install the "Hello world" thing https://www.magiclantern.fm/forum/index.php?topic=14732.0 and it semi-works: the backlight is still broken, but the text is displayed when I use a lamp to read.
Check LCD connectors. However my observations on R, 200D and 50D tells me that it wouldn't ERR70 but just run on the first boot (after battery is plugged in), then after shutdown will never power "on" again until battery is disconnected.

If you have your ROM dumps saved you can try running those in QEMU, as well as make a set of new dumps (just backup first and then remove dumps from memory card - next time ML will create a new set) and try them. If they crash in QEMU it is a good indication software issue (props? rom chip dying?).
EOS R, 200D, 750D, 50D...

tobiasBora

  • New to the forum
  • *
  • Posts: 8
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #116 on: August 16, 2021, 10:12:24 AM »
@kitor: ok thanks for the precision! So I tried to get the ROM dumps, and they run fine in qemu (thanks names_are_hard!). So I guess it's a hardware issue...

I tried to open the LCD case+the pivot axis case, but I can't find any obvious broken wire... So I'm not sure yet if I should buy a new LCD screen (~30€ I think): I heard that LCD backlight can be broken due to a fuse on the mother board (and therefore changing the LCD screen would not solve the problem). But this is maybe out of the scope of this thread, so I created a new one there https://www.magiclantern.fm/forum/index.php?topic=26204.0 .

deemon84

  • Just arrived
  • *
  • Posts: 1
Re: [UNBRICKED] Bricked 60D Err 70
« Reply #117 on: September 16, 2021, 10:11:24 AM »
Same problem.
Dear a1ex, please send to me autoexec.bin for repair this problem

CRASH00.LOG

ASSERT: FALSE
at DevelopCombination.c:108, task RscMgr
lv:0 mode:0

RscMgr stack: 115e68 [115f90-114f90]
0xUNKNOWN  @ ff07b8cc:115f88
0xUNKNOWN  @ ff1dcb80:115f60
0xFF1DC5DC @ ff02c3fc:115f28
0xUNKNOWN  @ ff1dc60c:115f18
0xUNKNOWN  @ ff1dc694:115ef8
0xFF0CAE58 @ ff0c9858:115ec0
0xFF013EC0 @ ff0caf18:115ea0
0x1FE00378 @ 1fe006d8:115e68

Magic Lantern version : Nightly.2018Jul03.60D111
Mercurial changeset   : 7a3b5fa3f4c6 (unified) tip
Built on 2018-07-02 22:19:47 UTC by jenkins@nightly.
Free Memory  : 392K + 1920K

LOG000.LOG

     86:   173.626 [STARTUP] ERROR ASSERT : DevelopCombination.c, Task = RscMgr
     87:   173.716 [STARTUP] ERROR ASSERT : Line 108
     88:   173.770 [STARTUP] ERROR ASSERT : FALSE
     89:   173.854 [STARTUP] ASSERT Time 1899/12/31 0:0:0
     90:   176.033 [STARTUP] startupErrorRequestChangeCBR (0x1d)
     91:   176.167 [STARTUP] startupErrorRequestChangeCBR : ErrorSend (101, ABORT)