Author Topic: Canon 70D (Read 1851850 times)

Walter Schulz · « **Reply #300 on:** February 08, 2015, 03:27:02 PM »

Run benchmark in photo mode and use CrystalDiskMark/ATTO to verify results. If results are within expection (write rate in cam about 40 MByte/s) retry and make sure to turn Global Draw off.

PanzerMamba · « **Reply #301 on:** February 08, 2015, 04:11:02 PM »

I can't run benchmark...

Camera won't start with SD card with ml alpha2. Few hours earlier everything was good, i turned off the camera, and put SD in the card reader for copy ml raw dng files. When I back SD to camera it won't- not only ML, but the whole camera. Something was crashed with ML or bootflag?

Walter Schulz · « **Reply #302 on:** February 08, 2015, 04:21:50 PM »

Copy AUTOEXEC.BIN + ML directory to card and try again.

PanzerMamba · « **Reply #303 on:** February 08, 2015, 05:36:56 PM »

Ok, after substitution ml + autoexec, camera has started. SD card seems to be ok (saving now lower than 41MB/s)

But after 90 seconds of recording raw dng I try to stop and save it, but it caused recording crashed again, with information "saving error, nothing saved" or something like that.

In 1600x900 achieved only 10 sec of material.

Walter Schulz · « **Reply #304 on:** February 08, 2015, 05:45:36 PM »

Which data rate was calculated by ML for this particular 90 seconds recording session? Where there any files written and how big are those? Any space left on card?

PanzerMamba · « **Reply #305 on:** February 08, 2015, 11:41:14 PM »

Files "stuck" in the sd- I couldn't move, remove, copy any of ml raw files. Second attempt after formating SD, and reinstaling ml alpha2...

larismanis · « **Reply #306 on:** February 09, 2015, 08:19:41 PM »

Hi guys,
sorry i am new with ML.
why i don't have RAW shooting menu and FPS setting menu in ML.. can somebody help me?

kubodhi · « **Reply #307 on:** February 10, 2015, 12:56:28 AM »

Quote from: larismanis on February 09, 2015, 08:19:41 PM

Hi guys,
sorry i am new with ML.
why i don't have RAW shooting menu and FPS setting menu in ML.. can somebody help me?

You'll need to enable the raw_rec module to get RAW recording, and FPS override isn't yet available in the current alpha.

ahmadkhmeesali · « **Reply #308 on:** February 10, 2015, 09:30:28 AM »

guy i need your help, i tried everything i could find any website, could help me please if someone had the same problem, HELP ME, i did everything i also bought a SanDisk class 10 94MB/s for the ML, nothing came out, my firmware is 1.1.1, and still could not install

HELP.

bsauce42 · « **Reply #309 on:** February 10, 2015, 09:32:36 AM »

Read the first post

DeafEyeJedi · « **Reply #310 on:** February 10, 2015, 09:33:22 AM »

Quote from: ahmadkhmeesali on February 10, 2015, 09:30:28 AM

guy i need your help, i tried everything i could find any website, could help me please if someone had the same problem, HELP ME, i did everything i also bought a SanDisk class 10 94MB/s for the ML, nothing came out, my firmware is 1.1.1, and still could not install

HELP.

you may have gotten an early version of 70D like some of us do including myself...

All we can do is patiently wait for them to sort out the bug for us.

That's the least we can do atm.

Which is nice, actually!

Thanks @nikfreak & everyone else on board...

ahmadkhmeesali · « **Reply #311 on:** February 10, 2015, 09:40:13 AM »

There was some info, apparently the main developer of the port did not have time to develop, but in December will be accepted for active work.

https://pp.vk.me/c625516/v625516897/2013/7WZOvrseiww.jpg

So we have to wait till December

ahmadkhmeesali · « **Reply #312 on:** February 10, 2015, 09:44:35 AM »

bsauce42 · « **Reply #313 on:** February 10, 2015, 09:44:53 AM »

Old post

ahmadkhmeesali · « **Reply #314 on:** February 10, 2015, 09:56:17 AM »

ohh, what a relieve, thank u

cant wait........

zahrten · « **Reply #315 on:** February 11, 2015, 12:22:57 AM »

1   Overlays
   -Zebras: __NOT OK (1/4 the screen not showing the zebras)
   -Focus Peak: _OK___
   -MagicZoom: __OK__
   -Cropmarks: __OK__
   -Ghost Image: __NOT OK (ghost image flicker)__
   -Spotmeter: __OK__
   -False Color: __NOT OK (Screen flicker, but otherwise work)__
   -Histogram: __OK__
   -Waveform: __OK__
   -Vectorscope: _OK___
2 Movie
   -BitRate: __OK__
   -REC Key: __OK__
   -Gradual Exposure: ____
   -FPS Override: Not availbale with Alpha0
   -HDR Video: ____
   -Vignetting: __OK (but very poor quality)__
   -Image Finetuning: ____
   -Movie Tweaks: __OK__
3   Shoot
   -Intervalometer: __OK__
   -Motion Detect: __NOT OK (could not get any of the modes working)__
   -Shoot Preferences: ____
4   Included Modules
   - Raw_rec: __OK (raw stable at 720p on sandisk extreme 45MB)__
   - ettr: ____
   - autoexpo: __OK (hard to say but it looked great)__
5   Other issues:
   The camera gets very hot very fast. 75C within 15 min
Focal lenth not showing correct

nikfreak · « **Reply #316 on:** February 11, 2015, 12:52:17 AM »

FYI: I am going to release a new Alpha today for testing. Again only for those cams which were already been able to run the previous builds.

saeed2vfx · « **Reply #317 on:** February 11, 2015, 09:37:57 AM »

Quote from: nikfreak on February 11, 2015, 12:52:17 AM

FYI: I am going to release a new Alpha today for testing. Again only for those cams which were already been able to run the previous builds.

X-STATE · « **Reply #318 on:** February 11, 2015, 10:54:21 AM »

hey there
video recording RAW begins with 5 second delay after pressing the record button.
It is normal?
on the other models the same situation?

Abe · « **Reply #319 on:** February 11, 2015, 11:07:17 AM »

Quote from: X-STATE on February 11, 2015, 10:54:21 AM

hey there
video recording RAW begins with 5 second delay after pressing the record button.
It is normal?
on the other models the same situation?

Yes, same situation, but not a big deal.

nikfreak · « **Reply #320 on:** February 11, 2015, 01:13:56 PM »

I updated the first post and also added Alpha3 download link.
Alpha3 still has property request changes set to disabled. Be sure to check the changelog.

Filip · « **Reply #321 on:** February 11, 2015, 01:50:36 PM »

Hey everyone!

First of all I wanted to thank nikfreak for the great job he is and has been doing on the ML version for 70D - much appreciated!!!

I have an issue with the intervalometer - it does not seem to work on Manual mode for some reason. It counts down to 0 but does not take any pictures. I works perfectly fine in Av/Auto/Tv but not in M.

Is this a known issue and/or has anyone else experienced the same problem?

I will do my best to post a list of all the tested features as soon as I have some time to spare.

Thanks in advance!

PanzerMamba · « **Reply #322 on:** February 11, 2015, 04:52:33 PM »

How to update correctly foram Aplha2 to Alpha3?

Do I have to update firmware again? Or only replace files form A2 by Aplha3?

walter_schulz · « **Reply #323 on:** February 11, 2015, 04:55:24 PM »

Delete AUTOEXEC.BIN and ML directory and copy Alpha 2 contents to card.

Installing ML doesn't replace/update firmware. Read FAQ.

zahrten · « **Reply #324 on:** February 11, 2015, 06:15:59 PM »

alpha 3
1   Overlays
-Zebras: __OK__
-Focus Peak: __OK__
-MagicZoom: __OK ___

2   Movie
-BitRate: __OK__
-FPS Override: __OK__

3   Shoot
-Intervalometer: __OK__
-Motion Detect: __NOT OK__ (Expo change did work, frame diff did not, steady hands would freeze the camera if no motion is detected,(had to turn off/on). Is repeatable.

4   Included Modules
- Raw_rec: __OK__stable at 1344X756_with SanDisk extreme 45 MB/s
- autoexpo: __OK__ (think it works but not sure ☺)

5   Other issues:
_Randomly gets kicked out of ML menu still present
_Still gets very hot. Hit 79C during test

News:

Author Topic: Canon 70D (Read 1851850 times)