Messages

Hello!!!

Is there an version for the 1300D???
Or solution for it to work!!!

Please...

TRY THIS LINK: https://www.magiclantern.fm/forum/index.php?topic=27033.msg245340#msg245340

The solution in the link LWL-Photographie posted doesnt worked in my T6. Maybe you will have same problem. But the solution in my post worked.

https://wiki.magiclantern.fm/faq#can_ml_suppress_black_columns_left_and_right_in_hdmi_streaming

Sorry I'm new in this world. Cant understand the post.

I am trying to solve this problem. I'm back with a new build:

https://bitbucket.org/ccritix/magic-lantern-git/downloads/magiclantern-Nightly.2023Sep30.1300D110.zip

It worked 100%, I went to Modify section, clear Overlay, so I got the Clean HDMI, but still have the black bars in video, like it is not stretched 1920x1080. Can you help?

I am trying to solve this problem. I'm back with a new build:

https://bitbucket.org/ccritix/magic-lantern-git/downloads/magiclantern-Nightly.2023Sep30.1300D110.zip

It Worked!! I'm gonna test right now and come back here latter.

If it fails again:
Insert card to cardreader and rename autoexec.bin to autoexec.org
Copy diagnostic autoexec.bin to card
http://a1ex.magiclantern.fm/debug/portable-hello-world/autoexec.bin

I have to maintain "Card boot flag" up?

The card will be like this: (?)

ML (The folder comes with the ML T6)
autoexec.org (Exec file from ML T6 renamed)
autoexec.bin (Exec file you sent in the link)

[Card bootflags in MLinstall.]

Forget that.
Cam is prepared. Done.

I did it all again in the card: Card bootflags in MLinstall.
With the camera connected via USB: The procedure in MLinstall with the camera "Get device info, Enable boot disk"

Still receiving the same message: "Your camera doesnt look like a 1300D 1.1.0"

https://www.magiclantern.fm/forum/index.php?topic=17969.msg245116#msg245116
If you are lucky you get it on first try. Most likely you have to deal with it several times before getting it right. Been there, done that.

Having 2 spare cards will be beneficial. A lot.

Done! 1.1.0 Again! Thx!

Now I need some help in this: In the mlinstall README, it says: "Note to Windows users: run the install-filter-win.exe in the install-libusb.exe folder to install LibUSB. Zadig usage is discouraged from now on." I'm not sure what to do with this information.

right

["Older firmware. Version 1.1.1. It's on the memory card. Delete old file and update using the latest version."]

Scroll down on linked site and get firmware file for 1300D. Version 1.1.0!

I receive this message:

"Older firmware. Version 1.1.1. It's on the memory card. Delete old file and update using the latest version."

Note: I've formated the memory card, downloaded version 1.1.0 and sent to memory card.

Magic Lantern says: Model detection error.
Your camera does not look like a 1300D 1.1.0

On my camera I have the firmware version 1.1.0. and it is a canon eos 1300D.
Did anyone know what I should do?

I have same problem after folowing these steps. Created a topic here in the fórum, come https://www.magiclantern.fm/forum/index.php?topic=27033.0

Now ML build for firmware 1.1.0 has valid reason to deny working ...
Use linked firmware file to downgrade to proper version.
https://pel.hu/eoscard

Ok, I download EOSCard. Now should I format my card and downgrade to 1.1.0 again? All I need to do is copy/paste the firmware from my computer to card?

Version detection mishaps can happen because Canon has a history delivering different sub-version named identically.
Nikfreak had the "pleasure" dealing with 4 different 70D firmwares reporting the same version.

Try this:
Install Canon firmware once again. Best using a different card.
Then try to restart with ML card.

If it fails again:
Insert card to cardreader and rename autoexec.bin to autoexec.org
Copy diagnostic autoexec.bin to card
http://a1ex.magiclantern.fm/debug/portable-hello-world/autoexec.bin

Remove battery. Insert card. Insert battery. Close compartment door.
Display will come up with additional info. Share this screen.

Next step: Contacting programmer and ask for compatible firmware file.

Hi, thank you for your answer and your help!

But... I made a mistake, I was trying to do what you said, downloaded firmware 1.1 from the Canon USA website, but I ended up downloading and installing 1.1.1 instead. Now my camera has this firmware. Should I still try to install Magic Lantern? 

What I did by Walter Schulz:

Downloads:
https://bitbucket.org/ccritix/magic-lantern-git/downloads/magiclantern-Nightly.2023Sep04.1300D110.zip
https://github.com/petabyt/mlinstall/releases
Pick your MLinstall package according to your OS. Windows (if not ancient) should run with win64 version.

- Run MLinstall
-- Windows: Extract zip to a proper location. Startup MLinstall as Admin. Most likely a messade "Windows protected your PC" will pop up. Select "More info" then "Run anyway".
-- Linux: Lookup how to enable AppImages on Linux PCs.

Installation steps for camera:
Connect cam and PC using USB cable.
Startup cam (if not already up and running). Check battery level!

Select USB tab in MLinstall.
Press "Get Device Info". You should get status info below telling you Manufacturer, Model, DeviceVersion and a cryptic SerialNumber. If you don't get this info on first try you may change USB port and/or check if other ptgrams like EOS Utility are running and hijacked/blocked cam. Terminate/stop such programs.
Redo until you get a proper connection! This is mandatory!

If (and only if) your cam is detected in MLinstall: Press "Enable Boot Disk".
Done. You can remove USB connection.

Installation steps for card:

Connect cardreader to PC.
Insert card.
Check if card is connected/mounted properly to your PC's OS.
If so: Press "Write card boot flags".
After this step you may close MLinstall.

Copy extracted build content to card.

Check card content:
- DCIM
- MISC
- ML
- autoexec.bin

If it looks like this: unmount  and card.
Done.

Hello, I installed Magic Lantern (ML) on my Canon T6 to enable clean HDMI livestreaming. However, after following the step-by-step instructions provided here on the forum, I received the following warning when I insert the memory card with ML already on it: (I don't even need to turn on the camera, and the warning appears.)

https://drive.google.com/file/d/1QPN8bP-Z0_kRQR__2YuWZB7vR_MbzPUj/view?usp=drive_link

https://drive.google.com/file/d/1QZ7iu5QB2a1FCAvNlzyY_s9ACXZXp7Dk/view?usp=drive_link


To try again, I would like to know if I should now perform the reverse step, open mlinstall again with the camera connected to my PC, and click on "Disable Boot Disk." This is to perform the reverse procedure that was requested of me earlier in "Get device info" and "Enable boot disk."

I followed the instructions correctly, but as a beginner, I might have done something wrong. In the mlinstall README, it says: "Note to Windows users: run the install-filter-win.exe in the install-libusb.exe folder to install LibUSB. Zadig usage is discouraged from now on." I'm not sure what to do with this information, and I didn't perform this procedure because I didn't read it the first time I attempted the installation.

Details: My Canon T6 firmware is version 1.1.0, and I updated it following the step-by-step instructions I learned here on the forum as well.

Probably not to be honest. That's just my opinion though.

But if the shutter has been replaced then it may live longer. Depends on if you're spending a lot of money on it or not. You can buy a 5D mark 2 for under $290 on ebay.

I'm Brazillian, he is selling by 200$ dollars more or less. Without lens. I need for 1080p livestreams, do you know if t5i work on it?

Anyways, better thinking, too much risk... 250k clicks are crazy for a camera that Canon says lasts 100k clicks right?

Hi, I have an oportunity to buy a Canon t5i that have 250.000 clicks. Worth it? She will live longer? He said that he sent it to revision and he replace the camera shutter to a new one.

I need for Livestream 1080p and saw that have ML support for it. I'm new in this world, so I would appreciate the help!

Print of the camera:

https://drive.google.com/file/d/1QPN8bP-Z0_kRQR__2YuWZB7vR_MbzPUj/view?usp=drive_link


I made again steps by the first, same error.

[Canon Oficial Firmware 1.1.0. In the camera shows 1.1.0 too.]

Please clear up information:
"I installed firmware 1.1 like learned ...". Did you install *Canon Firmware 1.1.0" or are you talkimg about ML build (which is not firmware)?
Startup cam without card inserted and check firmware information in Canon menu.

Canon Oficial Firmware 1.1.0. In the camera shows 1.1.0 too.

In this video he shows a new program I did not used: "Zadig" Should I do like in this video or ignore this cause its not necessary anymore?

Thank you for your help! Can you help me a little more?

I did everything you said, but when I turn on the camera, says more or less this: "Looks like this is not a 1300D, with firmware 1.1.0" etc.

My camera is a T6, I installed the 1.1 firmware like learned in this ML forum, the instalation was completed 100%. Anything I could did wrong for this error message? Any fix for this?

My reason to install ML is the "Clean HDMI" and maybe the "30 minutes shutdown timer" for use in my Podcast Studio.