« previous next »
Pages: 1 ... 33 34 [35] 36 37 ... 75

Author Topic: Canon EOS M  (Read 1717598 times)

alias

  • New to the forum
  • *
  • Posts: 6
Re: Canon EOS M
« Reply #850 on: December 12, 2015, 10:39:01 PM »
how i can downloaded this????
Logged

Walter Schulz

  • Contributor
  • Hero Member
  • *****
  • Posts: 8817
Re: Canon EOS M
« Reply #851 on: December 12, 2015, 10:45:17 PM »
Reading first post of this thread might help. Use "Show older builds" to get last successful build.
Logged

dfort

  • Guest
Re: Canon EOS M
« Reply #852 on: December 12, 2015, 10:50:14 PM »
Quote from: alias on December 12, 2015, 10:39:01 PM
how i can downloaded this????

If you are referring to my experimental build with the white balance hack, you can find it here:

https://bitbucket.org/daniel_fort/magic-lantern/downloads

This is where I share my working version and it contains stuff that hasn't been merged yet so caveat emptor!
Logged

Licaon_Kter

  • Hero Member
  • *****
  • Posts: 519
  • M
Re: Canon EOS M
« Reply #853 on: December 21, 2015, 12:50:17 AM »
 8) :o

Latest Build
magiclantern-Nightly.2015Dec21.EOSM202.zip
Built on: 2015-12-21 01:07:56 +0200
Changeset: c897f3f

GOGOGO: http://builds.magiclantern.fm/


Thx @a1ex, @dfort, @dpjpandone and everyone else.
Logged

dfort

  • Guest
Re: Canon EOS M
« Reply #854 on: December 21, 2015, 01:44:19 AM »
Yay!

Thanks @Licaon_Kter for running through all those batteries in order to create the data needed to make this happen.
Logged

tupp

  • Member
  • ***
  • Posts: 130
Re: Canon EOS M
« Reply #855 on: December 21, 2015, 07:26:43 AM »
Keep up the great work!!!

Thanks!
Logged

DeafEyeJedi

  • Hero Member
  • *****
  • Posts: 3413
  • 5D3 | M1 | 7D | 70D | SL1 | M2 | 50D
Canon EOS M
« Reply #856 on: December 21, 2015, 07:27:01 AM »
Merry Christmas to @Licaon_Kter for your excellent work as always as well as to everyone else on board for bringing magic back to the M.

Feels good to finally take out the little M from my kit bag and will definitely do a test run with the latest ML on it once again!

[emoji319]
Logged
5D3.113 | 5D3.123 | EOSM.203 | 7D.203 | 70D.112 | 100D.101 | EOSM2.* | 50D.109

a1ex

  • Administrator
  • Hero Member
  • *****
  • Posts: 12564
Re: Canon EOS M
« Reply #857 on: December 21, 2015, 08:14:24 AM »
I'm looking for feedback about FPS override changes.

In particular, set FPS override to max (65 fps) and try all available modes. You should get the following figures:

Quote
* 45.02 fps in 3x crop standby (available for raw recording; limited to 45 as suggested by LK)
* 34.37 fps in 3x crop H.264 (without video hacks)
* 31.24 in 1080p 1x (can be pushed to 33fps in H.264 if desired)
* 62.16 fps in 720p (can probably be pushed further)
* 31.24 fps in photo mode (no big deal here)
* 35.96 fps in 5x zoom (available for raw recording; can be pushed further if desired)

And, of course, you should not get garbled images in any video mode.
Logged

josepvm

  • Member
  • ***
  • Posts: 212
Re: Canon EOS M
« Reply #858 on: December 22, 2015, 11:27:01 AM »
Many thanks to A1ex, Licaon_Kter, dfort, and dpjpandone for your efforts to improve ML for the EOS M, and making possible this new nightly build !

I do not shoot video, but I'm glad to see that an old issue with A-ETTR present in previous builds for EOS-M seems fixed now.

ETTR worked in previous versions, but the "ETTR ..." on-screen message during exposure adjust locked and did not dissapear until I pressed the shutter button.  So I needed to look at ETTR hint in RAW histobar to know if A-ETTR had already fiinished calculation or not. With the new build, this issue is gone, A-ETTR works fine.


Thanks again !

Logged

Licaon_Kter

  • Hero Member
  • *****
  • Posts: 519
  • M
Re: Canon EOS M
« Reply #859 on: December 22, 2015, 03:00:43 PM »
 
Quote from: josepvm on December 22, 2015, 11:27:01 AM
I do not shoot video, but I'm glad to see that an old issue with A-ETTR present in previous builds for EOS-M seems fixed now.
Not sure I saw that before, but I'm glad it's fixed. :)
Logged

Spooke

  • New to the forum
  • *
  • Posts: 32
Re: Canon EOS M
« Reply #860 on: December 26, 2015, 12:53:46 PM »
Is anyone here using a Wi-Fi SD card with their EOS M? Please could someone recommend me one, I'd really like to be able to transfer RAW to my phone and edit in Snapseed (supports RAW). Thanks!!
Logged

Licaon_Kter

  • Hero Member
  • *****
  • Posts: 519
  • M
Re: Canon EOS M
« Reply #861 on: December 26, 2015, 03:01:00 PM »
Logged

Walter Schulz

  • Contributor
  • Hero Member
  • *****
  • Posts: 8817
Re: Canon EOS M
« Reply #862 on: December 26, 2015, 03:04:06 PM »
Eye-Fi X2 won't work but according to a1ex Transcend card may have not that problem.
http://www.magiclantern.fm/forum/index.php?topic=16249.msg157683#msg157683
Logged

Licaon_Kter

  • Hero Member
  • *****
  • Posts: 519
  • M
Re: Canon EOS M
« Reply #863 on: December 26, 2015, 03:50:16 PM »
Yeah, but the speed is meh.
Logged

maxEmpty

  • New to the forum
  • *
  • Posts: 6
Re: Canon EOS M
« Reply #864 on: December 28, 2015, 08:14:11 AM »
OMFG a1ex, Licaon_Kter, dfort, and dpjandone for making this update possible, it took 9 months but it was the best christmas present i could have gotten from a bunch of people i have never met. you are all angels to me now and i hope you have the happiest holiday season ever!!!!!!!!!!
Logged
if at first you cant get L glass... Sell everything you own and get L glass.

Steve_FR

  • New to the forum
  • *
  • Posts: 13
  • 550D / EOSM
Re: Canon EOS M
« Reply #865 on: December 29, 2015, 01:45:49 AM »
magiclantern-Nightly.2015Dec21.EOSM202

Ran the following FPS tests. Max user selectable FPS topped at 70. Tests run at both 65 and 70, no change between them.
Resulting displayed fps results:

1920x1080@30 (no crop mode)
Actual fps: 31.237
Lowest shutter I can select is 1/34.85. The next step after that results in flashing video with horizontal pink bands, and a shutter speed of 0" -6 degrees.
Highest selectable shutter speed: 1/8791, 1 degree.

1920x1080@24 (no crop mode)
Actual fps: 31.237
Lowest clean shutter: 1/34.85. Next step also results in flashing video with horizontal pink bands, and a shutter speed of 0" -6 degrees.
Highest selectable shutter speed: 1/8791, 1 degree.

1280x720@60 (no crop mode)
Actual fps: 31.237
At this setting, I was unable to reduce my shutter below 1/68.91 @ 163 degrees. Shutter speed idled between 1/68.83 and 1/68.91.

1920x1080@30 fps (Movie Crop Mode)
Actual fps: 45.022
Lowest clean shutter: 1/52.81. idles to 1/52.86. Next step, shutter 0" -162 degrees. Flashing video with horizontal pink lines.

1920x1080@24 fps (Movie Crop Mode)
Actual fps: 45.022
Lowest clean shutter:1/92.54 idles to 1/92.68. Next step, 0" -293 degrees. Flashing video with horizontal pink lines.
Logged

a1ex

  • Administrator
  • Hero Member
  • *****
  • Posts: 12564
Re: Canon EOS M
« Reply #866 on: December 29, 2015, 08:46:43 AM »
Ouch - that doesn't sound good.

Do the artifacts go away if you increase Timer B?

If yes, can you find the safe limit for this timer in each video mode? (that is, the lowest value for Timer B where all shutter speeds work)
Logged

Steve_FR

  • New to the forum
  • *
  • Posts: 13
  • 550D / EOSM
Re: Canon EOS M
« Reply #867 on: December 30, 2015, 08:48:10 PM »
Yes, artifacts begin to disappear as the Timer B is increased.  Below are the lowest safe limits I could find that keep the maximum shutter speed below 1/4000. At the high shutter speeds, there is still an alternating variance that occurs, causing the video to rapidly flutter between  exposure levels. It is not noticable at low shutter speeds, as the variance is 0.02. At shutter speeds in excess of 1/3000, the variance is over 1/200.

1920x1080 @ 30 fps (Canon Menu)
Desired FPS: 65 (from 30)
Actual fps: 30.389

FPS Timer A 520 -8 (no user change was made)
Fps Timer B 2025 (FT+55)

Shutter min 1/33.79
Shutter max 1/3619.80 and 3846.20 (idle variance)



1920x1080 @ 24 fps (Canon Menu)
Desired FPS: 65 (from 30)
Actual fps: 30.389
Fps Timer A 520 -8 (no user change was made)
Fps TImer B 2025 (FT+55)

Shutter min: 1/33.79
Shutter max: 1/3619.80 and 3846.20 (idle variance)


1280x720 @ 60 fps (Canon Menu)
Desired FPS: 65 (from 30)
Actual fps: 30.389
Fps Timer A 520 -8 (no user change was made)
Fps Timer B 2025 (FT+55)

shutter min: 1/64.84
Shutter max: 1/3619.80 and 3846.20 (idle variance)

ML FPS Override menu still displays "From 30" even when resolution is set to 1280x720 @ 60 fps in the canon menu, maximum actual FPS idles at 30.389.
Logged

Licaon_Kter

  • Hero Member
  • *****
  • Posts: 519
  • M
Re: Canon EOS M
« Reply #868 on: December 30, 2015, 09:43:32 PM »

Quote from: Steve_FR on December 30, 2015, 08:48:10 PM
ML FPS Override menu still displays "From 30" even when resolution is set to 1280x720 @ 60 fps in the canon menu, maximum actual FPS idles at 30.389.
IIRC, the fps will change once RECording starts, the menu is at 30 always.

Logged

Steve_FR

  • New to the forum
  • *
  • Posts: 13
  • 550D / EOSM
Re: Canon EOS M
« Reply #869 on: December 31, 2015, 03:49:24 AM »
Follow up for ML Movie Crop Mode timer values:

1920x1080 @ 30 fps (ML Movie Crop Mode)

Desired FPS: 65
Actual fps: 30.720

FPS Timer A: 532 (FT-8)
FPS Timer B: 1958 (FT+622)

Shutter min: 1/34.18
Shutter max: 1/3538.20 and 1/3759.40 (idle variance)


1920x1080 @ 24 FPS (ML Movie Crop Mode)

Desired FPS: 65
Actual fps: 24.581

FPS Timer A: 532 FT-8
FPS Timer B: 2447 (FT+1111)

Shutter min: 1/34.16
Shutter max: 1/3538.20 and 1/3759.40 (idle variance)

Side note: While testing FPS Timer B values above FT+1120, ML interface froze and I was unable to shut the camera off. I ejected the battery, and the problem occurred again. After quickly accessing ML menu and lowering Timer B, the problem did not happen again. I attempted to reproduce, but was unable to get it to happen a third time.

@Licaon_Kter You were right about the FPS, thank you!
Logged

musicmanx

  • New to the forum
  • *
  • Posts: 9
Re: Canon EOS M
« Reply #870 on: January 04, 2016, 01:12:23 PM »
hi,
but the max resolution for record in raw 25p whit the m1 ??

Thanks

Alessio
Logged

Licaon_Kter

  • Hero Member
  • *****
  • Posts: 519
  • M
Re: Canon EOS M
« Reply #871 on: January 04, 2016, 03:46:11 PM »
At 24 fps I get 1280x720 infinite runtime.
Logged

musicmanx

  • New to the forum
  • *
  • Posts: 9
Re: Canon EOS M
« Reply #872 on: January 05, 2016, 08:12:28 AM »
thanks
Logged

yt2

  • New to the forum
  • *
  • Posts: 3
Re: Canon EOS M
« Reply #873 on: January 07, 2016, 01:59:18 PM »
Hi guys!
I'm having problems when I'm recording H264 video. The video turns to black after few minutes although the time indicator is still counting. This happens randomly (sometimes 3mins sometimes 15min) . I've tried with both ML and Canon interface, with different sd cards,another lens, different batteries but the problem still exists. I 've noticed weird colors (pink mostly) on lcd. I was using magiclantern-Nightly.2015Dec21.EOSM202 with 2.0.2 firmware. I've also re-updated 2.0.2 firmware with EOS Utility. It didn't worked. I have recorded a short session with another camera, you can download two small video files (around 5mb) from here : http://we.tl/pIBOem6yDS

Any ideas?
Logged

Licaon_Kter

  • Hero Member
  • *****
  • Posts: 519
  • M
Re: Canon EOS M
« Reply #874 on: January 07, 2016, 04:03:59 PM »


Quote from: yt2 on January 07, 2016, 01:59:18 PM
I'm having problems when I'm recording H264 video.
Maybe report it here: https://bitbucket.org/hudson/magic-lantern/issues
Logged
Pages: 1 ... 33 34 [35] 36 37 ... 75
« previous next »