Canon EOS M

Started by jordancolburn, December 30, 2013, 10:21:20 PM

Previous topic - Next topic

0 Members and 6 Guests are viewing this topic.

alias

how i can downloaded this????

Walter Schulz

Reading first post of this thread might help. Use "Show older builds" to get last successful build.

dfort

Quote from: alias on December 12, 2015, 10:39:01 PM
how i can downloaded this????

If you are referring to my experimental build with the white balance hack, you can find it here:

https://bitbucket.org/daniel_fort/magic-lantern/downloads

This is where I share my working version and it contains stuff that hasn't been merged yet so caveat emptor!

Licaon_Kter

 8) :o

Latest Build
magiclantern-Nightly.2015Dec21.EOSM202.zip
Built on: 2015-12-21 01:07:56 +0200
Changeset: c897f3f

GOGOGO: http://builds.magiclantern.fm/


Thx @a1ex, @dfort, @dpjpandone and everyone else.

dfort

Yay!

Thanks @Licaon_Kter for running through all those batteries in order to create the data needed to make this happen.

tupp

Keep up the great work!!!

Thanks!

DeafEyeJedi

Merry Christmas to @Licaon_Kter for your excellent work as always as well as to everyone else on board for bringing magic back to the M.

Feels good to finally take out the little M from my kit bag and will definitely do a test run with the latest ML on it once again!

[emoji319]
5D3.113 | 5D3.123 | EOSM.203 | 7D.203 | 70D.112 | 100D.101 | EOSM2.* | 50D.109

a1ex

I'm looking for feedback about FPS override changes.

In particular, set FPS override to max (65 fps) and try all available modes. You should get the following figures:

Quote
* 45.02 fps in 3x crop standby (available for raw recording; limited to 45 as suggested by LK)
* 34.37 fps in 3x crop H.264 (without video hacks)
* 31.24 in 1080p 1x (can be pushed to 33fps in H.264 if desired)
* 62.16 fps in 720p (can probably be pushed further)
* 31.24 fps in photo mode (no big deal here)
* 35.96 fps in 5x zoom (available for raw recording; can be pushed further if desired)

And, of course, you should not get garbled images in any video mode.

josepvm

Many thanks to A1ex, Licaon_Kter, dfort, and dpjpandone for your efforts to improve ML for the EOS M, and making possible this new nightly build !

I do not shoot video, but I'm glad to see that an old issue with A-ETTR present in previous builds for EOS-M seems fixed now.

ETTR worked in previous versions, but the "ETTR ..." on-screen message during exposure adjust locked and did not dissapear until I pressed the shutter button.  So I needed to look at ETTR hint in RAW histobar to know if A-ETTR had already fiinished calculation or not. With the new build, this issue is gone, A-ETTR works fine.


Thanks again !


Licaon_Kter

 
Quote from: josepvm on December 22, 2015, 11:27:01 AM
I do not shoot video, but I'm glad to see that an old issue with A-ETTR present in previous builds for EOS-M seems fixed now.
Not sure I saw that before, but I'm glad it's fixed. :)

Spooke

Is anyone here using a Wi-Fi SD card with their EOS M? Please could someone recommend me one, I'd really like to be able to transfer RAW to my phone and edit in Snapseed (supports RAW). Thanks!!


Walter Schulz

Eye-Fi X2 won't work but according to a1ex Transcend card may have not that problem.
http://www.magiclantern.fm/forum/index.php?topic=16249.msg157683#msg157683

Licaon_Kter

Yeah, but the speed is meh.

maxEmpty

OMFG a1ex, Licaon_Kter, dfort, and dpjandone for making this update possible, it took 9 months but it was the best christmas present i could have gotten from a bunch of people i have never met. you are all angels to me now and i hope you have the happiest holiday season ever!!!!!!!!!!
if at first you cant get L glass... Sell everything you own and get L glass.

Steve_FR

magiclantern-Nightly.2015Dec21.EOSM202

Ran the following FPS tests. Max user selectable FPS topped at 70. Tests run at both 65 and 70, no change between them.
Resulting displayed fps results:

1920x1080@30 (no crop mode)
Actual fps: 31.237
Lowest shutter I can select is 1/34.85. The next step after that results in flashing video with horizontal pink bands, and a shutter speed of 0" -6 degrees.
Highest selectable shutter speed: 1/8791, 1 degree.

1920x1080@24 (no crop mode)
Actual fps: 31.237
Lowest clean shutter: 1/34.85. Next step also results in flashing video with horizontal pink bands, and a shutter speed of 0" -6 degrees.
Highest selectable shutter speed: 1/8791, 1 degree.

1280x720@60 (no crop mode)
Actual fps: 31.237
At this setting, I was unable to reduce my shutter below 1/68.91 @ 163 degrees. Shutter speed idled between 1/68.83 and 1/68.91.

1920x1080@30 fps (Movie Crop Mode)
Actual fps: 45.022
Lowest clean shutter: 1/52.81. idles to 1/52.86. Next step, shutter 0" -162 degrees. Flashing video with horizontal pink lines.

1920x1080@24 fps (Movie Crop Mode)
Actual fps: 45.022
Lowest clean shutter:1/92.54 idles to 1/92.68. Next step, 0" -293 degrees. Flashing video with horizontal pink lines.

a1ex

Ouch - that doesn't sound good.

Do the artifacts go away if you increase Timer B?

If yes, can you find the safe limit for this timer in each video mode? (that is, the lowest value for Timer B where all shutter speeds work)

Steve_FR

Yes, artifacts begin to disappear as the Timer B is increased.  Below are the lowest safe limits I could find that keep the maximum shutter speed below 1/4000. At the high shutter speeds, there is still an alternating variance that occurs, causing the video to rapidly flutter between  exposure levels. It is not noticable at low shutter speeds, as the variance is 0.02. At shutter speeds in excess of 1/3000, the variance is over 1/200.

1920x1080 @ 30 fps (Canon Menu)
Desired FPS: 65 (from 30)
Actual fps: 30.389

FPS Timer A 520 -8 (no user change was made)
Fps Timer B 2025 (FT+55)

Shutter min 1/33.79
Shutter max 1/3619.80 and 3846.20 (idle variance)



1920x1080 @ 24 fps (Canon Menu)
Desired FPS: 65 (from 30)
Actual fps: 30.389
Fps Timer A 520 -8 (no user change was made)
Fps TImer B 2025 (FT+55)

Shutter min: 1/33.79
Shutter max: 1/3619.80 and 3846.20 (idle variance)


1280x720 @ 60 fps (Canon Menu)
Desired FPS: 65 (from 30)
Actual fps: 30.389
Fps Timer A 520 -8 (no user change was made)
Fps Timer B 2025 (FT+55)

shutter min: 1/64.84
Shutter max: 1/3619.80 and 3846.20 (idle variance)

ML FPS Override menu still displays "From 30" even when resolution is set to 1280x720 @ 60 fps in the canon menu, maximum actual FPS idles at 30.389.

Licaon_Kter


Quote from: Steve_FR on December 30, 2015, 08:48:10 PM
ML FPS Override menu still displays "From 30" even when resolution is set to 1280x720 @ 60 fps in the canon menu, maximum actual FPS idles at 30.389.
IIRC, the fps will change once RECording starts, the menu is at 30 always.


Steve_FR

Follow up for ML Movie Crop Mode timer values:

1920x1080 @ 30 fps (ML Movie Crop Mode)

Desired FPS: 65
Actual fps: 30.720

FPS Timer A: 532 (FT-8)
FPS Timer B: 1958 (FT+622)

Shutter min: 1/34.18
Shutter max: 1/3538.20 and 1/3759.40 (idle variance)


1920x1080 @ 24 FPS (ML Movie Crop Mode)

Desired FPS: 65
Actual fps: 24.581

FPS Timer A: 532 FT-8
FPS Timer B: 2447 (FT+1111)

Shutter min: 1/34.16
Shutter max: 1/3538.20 and 1/3759.40 (idle variance)

Side note: While testing FPS Timer B values above FT+1120, ML interface froze and I was unable to shut the camera off. I ejected the battery, and the problem occurred again. After quickly accessing ML menu and lowering Timer B, the problem did not happen again. I attempted to reproduce, but was unable to get it to happen a third time.

@Licaon_Kter You were right about the FPS, thank you!

musicmanx

hi,
but the max resolution for record in raw 25p whit the m1 ??

Thanks

Alessio

Licaon_Kter

At 24 fps I get 1280x720 infinite runtime.

musicmanx


yt2

Hi guys!
I'm having problems when I'm recording H264 video. The video turns to black after few minutes although the time indicator is still counting. This happens randomly (sometimes 3mins sometimes 15min) . I've tried with both ML and Canon interface, with different sd cards,another lens, different batteries but the problem still exists. I 've noticed weird colors (pink mostly) on lcd. I was using magiclantern-Nightly.2015Dec21.EOSM202 with 2.0.2 firmware. I've also re-updated 2.0.2 firmware with EOS Utility. It didn't worked. I have recorded a short session with another camera, you can download two small video files (around 5mb) from here : http://we.tl/pIBOem6yDS

Any ideas?

Licaon_Kter