Author Topic: Canon EF lens mount - Communication protocol  (Read 21927 times)

jplxpto

  • Developer
  • Hero Member
  • *****
  • Posts: 506
Canon EF lens mount - Communication protocol
« on: December 08, 2012, 02:42:44 AM »

"
The communication protocol between the camera is 8-data-bit, 1-stop-bit SPI (mode 3). The pins, from right to left on the lens, are:

Canon EF mount pins[2][17]
Name   Function   Notes
VBat   +6 volts to power internal lens focus motors   
Present on all EOS bodies and lenses

P-Gnd   Power ground
P-Gnd
VDD   +5.5 volts Digital logic power
DCL   Data from camera to the lens (MOSI)
DLC   Data from the lens to the camera (MISO)
LCLK   Camera body generated clock signal (SCLK, CPOL=1)
D-GND   Digital logic ground
COM1   Teleconverter common[18][19][20]   
Only on most L-series and some macro lenses

EXT0   Short to COM1 for 'Life Size Converter' and x1.4 teleconverter
EXT1   Short to COM1 for x2 and x1.4 teleconverter
"

http://en.wikipedia.org/wiki/Canon_EF_lens_mount#Stepping_motor


SDX

  • Moderators
  • Senior
  • *****
  • Posts: 288
  • Medialogist
Re: Canon EF lens mount - Communication protocol
« Reply #2 on: December 08, 2012, 11:27:47 AM »
Some thoughts about this. You'll have to read a bit though.
http://www.magiclantern.fm/forum/index.php?topic=1749.25
600D, EOS M - Flickr

jplxpto

  • Developer
  • Hero Member
  • *****
  • Posts: 506

eos-dacious

  • New to the forum
  • *
  • Posts: 5
Re: Canon EF lens mount - Communication protocol
« Reply #4 on: February 28, 2016, 06:28:43 PM »
Is there a way to intercept the raw data that is sent or received over the electrical connection pins in the EF-Mount from within ML ?
Are there any adressess that are constantly changing while there is communication going on with lens?

Btw.: the probably currently best compilation of the Canon EOS EF-mount protocol can be found in this post: www.dslr-forum.de/showpost.php?p=12221153&postcount=554

a1ex

  • Administrator
  • Hero Member
  • *****
  • Posts: 12353
  • Emergencies only
Re: Canon EF lens mount - Communication protocol
« Reply #5 on: February 28, 2016, 07:34:02 PM »
This happens on another processor, which we don't really understand yet.

To get the code running on that processor, see https://bitbucket.org/hudson/magic-lantern/branch/mpu

If you have about 1-2 years of spare time, and some low-level programming knowledge, you could try to modify a Tx19A emulator (such as NikonHacker's) and have fun understanding that code.

Looking inside an EOS M3 might be interesting: from strings, it appears to have 3 secondary CPUs: MechaCpuA, MechaCpuB, SubCPU. I have no idea what's there yet, but at least the implementation seems different than on current DSLRs.

In other words, I think it's much easier to intercept it at hardware level.

nikfreak

  • Developer
  • Hero Member
  • *****
  • Posts: 1143
Re: Canon EF lens mount - Communication protocol
« Reply #6 on: February 29, 2016, 04:28:51 PM »
You could modify the following setup and treat it as PoC for debugging the cam hardware if you extend it:

http://web.media.mit.edu/~bandy/invariant/move_lens.pdf

What I was planning to do is:
  • Get my hands onto a small body (pref. EOS-M)
  • Add JTAG hardware / software to my equipment (UART is known to provide access to DryShell) but JTAG with OpenOCD would be preferrable.
  • Dismantle the body to gain access to the pins (RX / TX / GND ...)
  • Start debugging. I assume this would also help in terms of Digic6/7 development if a newer cam is used - not only extend private knowledge by a steady learning curve. Got only experience with flashing OpenWRT routers so far via serial console and cheapo FTDI cables / adapters
70D.112 & 100D.101