Thank you, good to know that the highest temperature is in the EXIF data ...
Etiquette, expectations, entitlement...
@autoexec_bin | #magiclantern | Discord | Reddit | Server issues
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Show posts MenuQuote from: coon on December 15, 2020, 03:21:58 PM
I am using RAW Therapee which cannot read EXIF data from CR3 RAW files, used on newer canon models. Therefore I cannot answer that right now. If someone knows another free tool which can do that, please let me know!
exiftool -h IMG_1234.CR3 >t.txt
Quote from: coon on December 14, 2020, 08:22:55 PM
Displays the values of several temperature sensors. TEMP(A) seems to be the sensor of the main CPU.
Quote from: srsa on September 03, 2020, 01:11:27 AM
So far confirmed to exist on:
PowerShot SX740
EOS M50
EOS R, RP, R5, R6
EOS 250D
Quote from: Walter Schulz on November 24, 2020, 09:15:40 AMNo the Script runs only on M3, M10 and M100.(I wrote the M with CHDK).
Joerg, have you been able to run that script on EOS M?
Quote from: ChristianEOS on November 24, 2020, 05:50:59 AM
I would just shoot with my mobile with Lightroom you also can you get RAW pictures.
Quote from: nicotom on March 02, 2020, 02:29:28 AM
Hi everyone.
I am a fan of Timelapses and for now i have used qDslrDashboard with my 5D3.
Everything is going well but if, for exemple, a car passes by, ETTR will adjust the shutter speed and will make it shorter for the next picture.
I would like to avoid that.
Quote from: Walter Schulz on July 15, 2020, 09:00:41 PM
Because there it is clearly pointed out that you can not use EOS Utility to downgrade 1.3.6 I strongly suggest to re-read said instructions and begin following them.
Quote from: yourboylloyd on November 24, 2020, 07:06:14 AM
Does it really?
Quote from: coon on September 18, 2020, 07:21:02 PMLooks like this...
Interesting. Shutter count also broken here or has some encoding scheme.
Quote from: coon on September 18, 2020, 07:21:02 PMYes, would be intresting...
It meight be interesting getting a dump of a fresh RP with 0 shots taken to find out the origin value.
Quote from: coon on September 18, 2020, 03:18:33 PMIntresting...
Counter increased by one but is still invalid.
Quote from: kitor on September 18, 2020, 02:00:11 PMThen try it again with original LP-E6N,
ERR70 was a result of my broken Basic script.
Quote from: kitor on September 18, 2020, 01:53:40 PMDu you use original Batterie?
There are some interesting logs here
Quote from: coon on September 18, 2020, 11:07:39 AMHave you tried to make one shoot and a second dump?
TotalShutter value seems to be invalid here. Could someone else with an RP run that script too and post the results here?
Quote from: coon on September 18, 2020, 10:38:08 AM
RP:
Shutter count seems to be invalid.
Quote from: yourboylloyd on September 18, 2020, 08:22:01 AM
It's probably because there is a mechanical shutter and electronic shutter.
private sub Initialize()
System.Create()
CamInfo_Debug(1)
end sub
Quote from: yourboylloyd on September 04, 2020, 03:20:42 AM
Edit: I just counted and found that there is a total of 26 buttons (including dials and joystick directions) on the R6. Assuming that there are 2 input combinations to start the script, there are a possible 26x26 = 676 combinations that are possible to be the solution XD
Quotehttps://chdk.fandom.com/wiki/Canon_Basic/Card_Setup
Some touchscreen cameras run the script when the focus lever is turned to the left.
Page created in 0.107 seconds with 13 queries.