Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - JCBEos

Pages: [1] 2 3
Share Your Videos / [7D Raw Video] Myocastor coypus
« on: May 26, 2014, 05:45:16 PM »
A short river rat clip; enjoyin a good pond bathing

1920*818, EOS 7D


Tragic Lantern / Re: 7D Raw Thread
« on: October 03, 2013, 07:29:54 PM »
Hopefully I can get the master to boot off the other repo with less updates. Then I can see what is happening to the registers/memory.

 :D :D :D :D

uhm when directly converting to raw, you get the message about "in the middle" and when
writing to mlv, it just doesnt output any image?

that's it :/

This is just very smart... and awesome!

My brain hurts a little after trying to understand those mathematics...

but what if we could apply this to a high-end lens, would this make a better super sharp lens???

yeah this file is corrupted - it stops somewhere in the middle of data.
seems some part of it is missing.

run the same command, just without -r to dump its content into the output file in MLV mode (name it blah.mlv)
then you can process it using mlv2dng

Ok so it seems to work, but it output a 1ko raw file :/

General Help Q&A / Re: Newbie: scripting for astrophoto, o
« on: September 29, 2013, 11:16:26 PM »
Indeed, it's like a HDR. ;)
But in astro-photography, regular photographic bracketing is not relevant because we need a very high S/N ratio (many shoots of the same bracket).

I know that  ;D

( with my RC and NEQ6

Just thought that it was possible to combine intervallometer and bracketting, by this I mean take -1/0/+1 shots at "T" time, then the same at "T+1" etc


Ok so I turned my brain "ON" and did some search....

I acheived to decode one of the two files with mlv_dump

but for the other one...

Modules Development / Re: Magic Lantern (RAW) Video format v2.0
« on: September 29, 2013, 10:22:37 PM »
Keep your personal stuff off this board!

If you read this thread you will find this on reply 218:

and a bit lower you will find this:

So try it and see.  If it is not compatible with current build then wait until dev makes it available.

Thanks for this post Renato, it helped me a lot

Tragic Lantern / Re: 7D Raw Thread
« on: September 29, 2013, 10:09:45 PM »
Sticky something is on? Maybe some ML assert is tripped? I compiled last night and get no blinking.

Ok now it's gone... I maybee need to stop playin with menus... or stop drinking. Or both  ::)

General Help Q&A / Re: Newbie: scripting for astrophoto, o
« on: September 29, 2013, 04:32:17 PM »
what you wanna do (composite different exposure to get the galaxy core not burn for ex.) is quite similar to HDR... have you simply tried with advanced bracketing?

Tragic Lantern / Re: 7D Raw Thread
« on: September 29, 2013, 01:43:24 PM »
Just noticed that with the last 2 builds, the back red led ("access lamp") is constantly blinking... excepted when I pop up the ML menu.

Strange :/

i quote myself again regarding corrupted mlv files.

 - what happens?  - some error message?

the program crash, i posted the windows error message here

 - what does mlv_dump say?

where can I download the mlv_dump.exe file? haven't found a good link here

 - can you convert it to legacy raw?

sorry but what do you mean? (  :-[ )

 - what does the mlv player say?

the one on the camera? or your "MLV Viewer"?
MLV viewer is crashing trying to open the file.

 - where can i download the corrupted files?

do you got a place where I can upload two 3gigs files?
Or maybe i can directly upload them to you using a .torrent or something else (got a 100mb/s symetric bandwith)

Thanks in advance, and sorry for the lack of provided infos  :-\

Tragic Lantern / Re: 7D Raw Thread
« on: September 29, 2013, 12:40:57 PM »
Thanks for your answers :)

(and btw your work & time  :-* )

Tragic Lantern / Re: 7D Raw Thread
« on: September 28, 2013, 09:04:41 PM »
Press the zoom button to get 5x and then press trash button to go to ML menu... there go to your raw setting and chose your desired resolution.

@1%: Is there a way to modify ML in order to be able to set crop mode settings without being in x5 mode?

I got FPS working from slave (since master isn't even booting for me now).. not for H264 yet. With the new edmacs I get 1920x1038 cont at 79.x mb/s in zoom mode.

but is "since master isn't even booting for me now" a big problem?

Once again, got 2 files I can't decode :/

I'll upload them if I can't get the job done.

I tried to see if there's something wrong in the file structure with a hex editor, but nothing seems weird.

TIP: I achieved to decode a "corrupted" file using the Windows XP 3 compatibility mode. (Windows 8 x64)

Tragic Lantern / Re: 7D Raw Thread
« on: September 24, 2013, 11:34:09 AM »
got that. I'm getting varying results at that resolution first got 700+ frames then 300+ then after awhile the LV when crazy,
I heard the mirror come down,
the LV image was frozen and the menu/screen info flashing erratically.

On the top screen of the cam an ERR message flashing . no number just ERR,

This is exactly the bug that I had.

And can someone try to compile the last 1% version ("Bump edmac on 7D up to 0x06... Now I can record fullHD LV continuously.")?
Thanks :)

Tragic Lantern / Re: 7D Raw Thread
« on: September 24, 2013, 01:49:09 AM »
With fir + fps override?

yes I forgot to write it, but that's with FPS override enabled

Tragic Lantern / Re: 7D Raw Thread
« on: September 23, 2013, 05:10:41 PM »
Done some shoots yesterday and I had several crashes in crop mode using 1% last build.

The screen started to flicker and then the camera crashed, I had to remove the battery each time to reboot the camera.

I'll check if I'll find some debug logs.

maybe we need a fixer for mlv raw files :/

Tragic Lantern / Re: 7D Raw Thread
« on: September 16, 2013, 01:25:31 PM »
Just received a 32Gb 1000x Lexar CF

is there some tests that I can do to help you, 1%?

Tragic Lantern / Re: 7D Raw Thread
« on: September 16, 2013, 12:06:36 AM »
1% so i got a 32 Komputer bay 1000X CF so its possible to format in exfat. instead of fat32? and if it supports in how do i format? yes i have window7 and reformatted in exfat then when into eoscard and installed aplha2  ( all the normal things to have a working ) but my 7d cant find it says card not supported. thanks again

exfat only (probably) supported (right now) for 128gb+ cards

Tragic Lantern / Re: 7D Raw Thread
« on: September 15, 2013, 03:09:04 PM »
You can use ligthroom or any viewer

I use Adobe Bridge.

There's also an Adobe "codec" to view DNGs in the explorer.

Tragic Lantern / Re: 7D Raw Thread
« on: September 15, 2013, 11:31:31 AM »
question does 7d support exfat?

Possibly, I don't have one to test but I see the exfat strings... maybe there is a way to fake out the camera and make it think the card is 128gb... also dunno if fir will run from 128gb cards.

Pages: [1] 2 3