Messages

1

Camera-specific Development / Re: Canon 650D 1.0.4 [Status: Alpha]

« on: August 04, 2013, 02:54:23 AM »

Installed & Working. Thank you for all your hard work nanomad & Satriani!

Sorry about being so impatient to try it out, guess I couldn't wait to get my hands on ML

2

Archived porting threads / Re: Canon 650D [Status: Alpha]

« on: August 03, 2013, 04:41:50 PM »

#5) The (step above) is why it isn't running. I believe You need to insert the card you copied the files to, and run the update, and leave that card in the camera to use to capture your media.

I think your right about the format.

I copied the files and ran the update (nothing ML related showed up doesn't run), but then for step 6 i'm not sure if I need to take out the card from the camera again, then place it back in the reader. Then for step 7 put it back into the camera?

Edit:

Just tried what I suggested above, didn't work either. :/

3

Archived porting threads / Re: Canon 650D [Status: Alpha]

« on: August 03, 2013, 04:23:28 PM »

Okay, sorry if I seem a bit confused here, but I think i'm misunderstanding some of the steps in the instructions which is giving me problems running ML. I've downloaded all the files needed...my steps followed in blue.

2. low level format your SD card. Done in-camera using the camera 'low level format card' option.

3.  Copy 650D-safe-dumper.fir on SD card. I took out my SD card and placed it into the card reader for this because the camera wouldn't allow me to transfer the file directly into the card (while it was in the camera) using the wire connection.

4. Copy the stuff from latest build on SD card (ML folder and autoexec.bin). Done

5. Start camera in M photo mode and run firmware update. It says I had to put a memory card in to do a firmware update? I don't know what to do with this step (take out the SD card from the reader and put it back into camera? If so, then do I put it back into the reader for step 6?) so I just left my card in the reader and skipped this step.

6. Run EOSCard, check EOS_Develop and BOOTDISK Checked both, hit 'save' at the top right to write the files in, status said, 'Write Successful'.

7. Put SD card in camera just press the trashcan button to run ML Done, but ML doesn't run.

@acme

I'm guessing that too. The official instructions on installing ML says "Format the card in the camera (low-level format)." and our 650D's have the option to tick "Low level format" when attempting to format our cards in-camera.

4

Archived porting threads / Re: Canon 650D [Status: Alpha]

« on: August 03, 2013, 01:42:49 AM »

WARNING - THE CODE ON THE REPOSITORY HAS SWITCHED TO THE 1.0.4 FIRMWARE FOR THE 650D

Don't use any newer builds for now until I open a new thread

BTW, 104 is working as good as 101

HALLELUJAH!!

My tears of joy are spilling over. :'D

WARNING - THE CODE ON THE REPOSITORY HAS SWITCHED TO THE 1.0.4 FIRMWARE FOR THE 650D

I don't really get what this means, but i'm guessing we wait for a new thread for fw 1.0.4? or...are the downloads on the first page good to go for 1.0.4?

5

Archived porting threads / Re: Canon 650D [Status: Alpha]

« on: July 27, 2013, 04:15:17 PM »

I'm working on the 1.0.4 port, more news in a couple of days

REJOICE!

That's some really great news, can't wait to hear what's going on!

6

Archived porting threads / Re: Canon 650D [Status: Alpha]

« on: July 04, 2013, 05:37:22 PM »

2. Does it matter that I'm using Canon firmware 1.0.1?

Thanks again to everyone who helped make ML on T4i possible.

Yes, as of now the Alpha Stage ML only works on 650D's running Canon firmware 1.0.1.

Some of us made the mistake of upgrading to the latest Canon firmware (1.0.4) which doesn't work with the current ML.

7

Archived porting threads / Re: Canon 650D [Status: Alpha]

« on: July 04, 2013, 01:44:02 PM »

Just an idea: Contact a Canon Support Partner and ask if they can downgrade.
Canon never made 1.0.1 downloadable for public.

Ciao, Walter

I contacted my Canon Support in Singapore where I live but they said there wasn't any way to downgrade my 1.0.4 even if I brought it into the shop (and mine's still under warranty).

Time to camp for that 1.0.4 build. 

P.S. Could we have a nice big red notice on the first post to say not to update to firmware 1.0.4 (till 1.0.4 ML is released)? Just in case another blind guy like me doesn't know and messes up while reading the instructions.