Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - domasa

Pages: 1 2 [3] 4 5
51
Reverse Engineering / Re: UHS-I / SD cards investigation
« on: April 08, 2018, 10:14:25 PM »
Will it be possible to overclock the "CF" interface...?
I had same question ☺
Quote
...what about brute force search registers for CompactFlash?  ;)

52
Reverse Engineering / Re: UHS-I / SD cards investigation
« on: April 07, 2018, 07:34:12 PM »
SanDisk Ultra 64GB (white/gray)
Code: [Select]
Before the hack: r:22MB/s w:14MB/s  W:10MB/s R:22MB/s  8)  [best 14MB/s]
SDR50 @ 96MHz  : sd_check_function =>
00C8 8001 8001 800F 800F 8001 801F 0000
8001 800F 800F 8001 801F 0000 0100 0000
800F 8001 801F 0000 0100 0000 0000 0000
801F 0000 0100 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 200 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,F)
Function group 1 (Access Mode)     1 (supported 0,1,2,3,4,F)
sd_set_function =>
0190 8001 8001 800F 800F 8001 801F 0000
8001 800F 800F 8001 801F 0000 0200 0000
800F 8001 801F 0000 0200 0000 0000 0000
801F 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 400 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,3,4,F)
r:43MB/s w:18MB/s  W:18MB/s R:43MB/s  8)  [best 18MB/s]
SDR50 @ 96MHz  : sd_set_function =>
0190 8001 8001 800F 800F 8001 801F 0000
8001 800F 800F 8001 801F 0000 0200 0000
800F 8001 801F 0000 0200 0000 0000 0000
801F 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 400 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,3,4,F)
r:43MB/s w:18MB/s  W:18MB/s R:43MB/s  :)  [best 18MB/s]
Best: sd_set_function =>
0190 8001 8001 800F 800F 8001 801F 0000
8001 800F 800F 8001 801F 0000 0200 0000
800F 8001 801F 0000 0200 0000 0000 0000
801F 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 400 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,3,4,F)
r:43MB/s w:18MB/s  W:17MB/s R:43MB/s  :)  [best 18MB/s]
Best: sd_set_function =>
0190 8001 8001 800F 800F 8001 801F 0000
8001 800F 800F 8001 801F 0000 0200 0000
800F 8001 801F 0000 0200 0000 0000 0000
801F 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 400 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,3,4,F)
r:43MB/s w:17MB/s  W:17MB/s R:43MB/s  ::) [best 18MB/s]

Done.
Please run THOROUGH tests before using!!!

SanDisk Ultra 64GB (red/gray)
Code: [Select]
Before the hack: r:22MB/s w:19MB/s  W:12MB/s R:22MB/s  8)  [best 19MB/s]
SDR50 @ 96MHz  : sd_check_function =>
00C8 8001 8001 800F 800F C001 801F 0000
8001 800F 800F C001 801F 0000 0100 0000
800F C001 801F 0000 0100 0000 0000 0000
801F 0000 0100 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 200 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,E,F)
Function group 1 (Access Mode)     1 (supported 0,1,2,3,4,F)
sd_set_function =>
00C8 8001 8001 800F 800F C001 801F 0000
8001 800F 800F C001 801F 0000 0200 0000
800F C001 801F 0000 0200 0000 0000 0000
801F 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 200 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,E,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,3,4,F)
r:43MB/s w:22MB/s  W:32MB/s R:43MB/s  8)  [best 22MB/s]
SDR50 @ 96MHz  : sd_set_function =>
00C8 8001 8001 800F 800F C001 801F 0000
8001 800F 800F C001 801F 0000 0200 0000
800F C001 801F 0000 0200 0000 0000 0000
801F 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 200 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,E,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,3,4,F)
r:43MB/s w:33MB/s  W:24MB/s R:43MB/s  8)  [best 33MB/s]
Best: sd_set_function =>
00C8 8001 8001 800F 800F C001 801F 0000
8001 800F 800F C001 801F 0000 0200 0000
800F C001 801F 0000 0200 0000 0000 0000
801F 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 200 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,E,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,3,4,F)
r:43MB/s w:21MB/s  W:25MB/s R:43MB/s  meh [best 33MB/s]
Best: sd_set_function =>
00C8 8001 8001 800F 800F C001 801F 0000
8001 800F 800F C001 801F 0000 0200 0000
800F C001 801F 0000 0200 0000 0000 0000
801F 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 200 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,E,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,3,4,F)
r:43MB/s w:24MB/s  W:25MB/s R:43MB/s  meh [best 33MB/s]

Done.
Please run THOROUGH tests before using!!!

Kingston 64GB
Code: [Select]
Before the hack: r:22MB/s w:6.4MB/s  W:6.9MB/s R:22MB/s  8)  [best 6.4MB/s]
SDR50 @ 96MHz  : sd_check_function =>
0064 8001 8001 800F 800F 8001 8017 0000
8001 800F 800F 8001 8017 0000 0100 0000
800F 8001 8017 0000 0100 0000 0000 0000
8017 0000 0100 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 100 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,F)
Function group 1 (Access Mode)     1 (supported 0,1,2,4,F)
sd_set_function =>
0064 8001 8001 800F 800F 8001 8017 0000
8001 800F 800F 8001 8017 0000 0200 0000
800F 8001 8017 0000 0200 0000 0000 0000
8017 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 100 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,4,F)
r:39MB/s w:7.2MB/s  W:8.2MB/s R:43MB/s  8)  [best 7.2MB/s]
SDR50 @ 96MHz  : sd_set_function =>
0064 8001 8001 800F 800F 8001 8017 0000
8001 800F 800F 8001 8017 0000 0200 0000
800F 8001 8017 0000 0200 0000 0000 0000
8017 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 100 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,4,F)
r:39MB/s w:7.2MB/s  W:5.7MB/s R:43MB/s  :)  [best 7.2MB/s]
Best: sd_set_function =>
0064 8001 8001 800F 800F 8001 8017 0000
8001 800F 800F 8001 8017 0000 0200 0000
800F 8001 8017 0000 0200 0000 0000 0000
8017 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 100 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,4,F)
r:39MB/s w:7.2MB/s  W:13MB/s R:42MB/s  :)  [best 7.2MB/s]
Best: sd_set_function =>
0064 8001 8001 800F 800F 8001 8017 0000
8001 800F 800F 8001 8017 0000 0200 0000
800F 8001 8017 0000 0200 0000 0000 0000
8017 0000 0200 0000 0000 0000 0000 0000
Switch Function Status version 0
Max current: 100 mA
Function group 6 (Reserved)        0 (supported 0,F)
Function group 5 (Reserved)        0 (supported 0,F)
Function group 4 (Power Limit)     0 (supported 0,1,2,3,F)
Function group 3 (Driver Strength) 0 (supported 0,1,2,3,F)
Function group 2 (Command System)  0 (supported 0,F)
Function group 1 (Access Mode)     2 (supported 0,1,2,4,F)
r:39MB/s w:7.2MB/s  W:13MB/s R:42MB/s  :)  [best 7.2MB/s]

Done.
Please run THOROUGH tests before using!!!

53
Reverse Engineering / Re: UHS-I / SD cards investigation
« on: April 07, 2018, 07:13:53 PM »
I downgraded firmware to 1.1.3. But I have problem with load module sd_uhs_d:




I have ML on CF card.

54
Reverse Engineering / Re: UHS-I / SD cards investigation
« on: April 07, 2018, 05:47:02 PM »
I tested five slow SD cards with 5D Mark III :


SanDisk Ultra 64GB (white/gray) : 33 MB/s

Code: [Select]
Before the hack: r:22MB/s w:19MB/s  W:21MB/s R:22MB/s  8)  [best 19MB/s]
SDR50 @ 96MHz  : r:43MB/s w:23MB/s  W:18MB/s R:43MB/s  8)  [best 23MB/s]
SDR50 @ 96MHz  : r:43MB/s w:19MB/s  W:16MB/s R:43MB/s  meh [best 23MB/s]
SDR50 @ 80MHz  : r:36MB/s w:12MB/s  W:19MB/s R:36MB/s  meh [best 23MB/s]
SDR50 @ 80MHz  : r:36MB/s w:16MB/s  W:12MB/s R:36MB/s  meh [best 23MB/s]
SDR50 @ 120MHz : r:54MB/s w:19MB/s  W:12MB/s R:54MB/s  meh [best 23MB/s]
SDR50 @ 120MHz : r:54MB/s w:17MB/s  W:15MB/s R:54MB/s  meh [best 23MB/s]
SDR104 @ 96MHz : r:43MB/s w:20MB/s  W:15MB/s R:43MB/s  meh [best 23MB/s]
SDR104 @ 96MHz : r:43MB/s w:24MB/s  W:21MB/s R:43MB/s  :)  [best 24MB/s]
SDR104 @ 80MHz : r:36MB/s w:18MB/s  W:21MB/s R:36MB/s  meh [best 24MB/s]
SDR104 @ 80MHz : r:36MB/s w:33MB/s  W:12MB/s R:36MB/s  8)  [best 33MB/s]
SDR104 @ 120MHz: r:54MB/s w:16MB/s  W:17MB/s R:ERR
SDR104 @ 120MHz: r:err [SAFE]  [BACK]
SDR104 @ 132MHz: r:60MB/s w:45MB/s  W:27MB/s R:ERR
SDR104 @ 132MHz: r:err [SAFE]  [BACK]
SDR104 @ 160MHz: r:71MB/s w:18MB/s  W:14MB/s R:ERR
SDR104 @ 160MHz: r:err [SAFE]  [BACK]
Best: r:36MB/s w:13MB/s  W:24MB/s R:36MB/s  ??? [best 33MB/s]
Best: r:36MB/s w:16MB/s  W:21MB/s R:36MB/s  ??? [best 33MB/s]

Done.
Please run THOROUGH tests before using!!!

SanDisk Ultra 64GB (red/gray) : 37 MB/s

Code: [Select]
Before the hack: r:22MB/s w:16MB/s  W:19MB/s R:22MB/s  8)  [best 16MB/s]
SDR50 @ 96MHz  : r:43MB/s w:22MB/s  W:19MB/s R:43MB/s  8)  [best 22MB/s]
SDR50 @ 96MHz  : r:43MB/s w:21MB/s  W:26MB/s R:43MB/s  ::) [best 22MB/s]
SDR50 @ 80MHz  : r:36MB/s w:20MB/s  W:26MB/s R:36MB/s  ::) [best 22MB/s]
SDR50 @ 80MHz  : r:36MB/s w:23MB/s  W:26MB/s R:36MB/s  :)  [best 23MB/s]
SDR50 @ 120MHz : r:54MB/s w:24MB/s  W:29MB/s R:54MB/s  :)  [best 24MB/s]
SDR50 @ 120MHz : r:54MB/s w:37MB/s  W:39MB/s R:54MB/s  8)  [best 37MB/s]
SDR104 @ 96MHz : r:43MB/s w:30MB/s  W:22MB/s R:43MB/s  meh [best 37MB/s]
SDR104 @ 96MHz : r:43MB/s w:26MB/s  W:27MB/s R:43MB/s  meh [best 37MB/s]
SDR104 @ 80MHz : r:36MB/s w:29MB/s  W:33MB/s R:36MB/s  meh [best 37MB/s]
SDR104 @ 80MHz : r:36MB/s w:36MB/s  W:26MB/s R:36MB/s  ::) [best 37MB/s]
SDR104 @ 120MHz: r:err [SAFE]  [BACK]
SDR104 @ 120MHz: r:err [SAFE]  [BACK]
SDR104 @ 132MHz: r:err [SAFE]  [BACK]
SDR104 @ 132MHz: r:err [SAFE]  [BACK]
SDR104 @ 160MHz: r:err [SAFE]  [BACK]
SDR104 @ 160MHz: r:err [SAFE]  [BACK]
Best: r:err [SAFE]  [BACK]
Best: r:err [SAFE]  [BACK]

Done.
Please run THOROUGH tests before using!!!

Lexar 633x 16GB : 19 MB/s

Code: [Select]
Before the hack: r:22MB/s w:18MB/s  W:16MB/s R:22MB/s  8)  [best 18MB/s]
SDR50 @ 96MHz  : r:43MB/s w:18MB/s  W:19MB/s R:43MB/s  :)  [best 18MB/s]
SDR50 @ 96MHz  : r:43MB/s w:18MB/s  W:19MB/s R:43MB/s  ::) [best 18MB/s]
SDR50 @ 80MHz  : r:36MB/s w:18MB/s  W:18MB/s R:36MB/s  ::) [best 18MB/s]
SDR50 @ 80MHz  : r:36MB/s w:18MB/s  W:18MB/s R:36MB/s  ::) [best 18MB/s]
SDR50 @ 120MHz : r:54MB/s w:19MB/s  W:19MB/s R:54MB/s  :)  [best 19MB/s]
SDR50 @ 120MHz : r:54MB/s w:19MB/s  W:19MB/s R:53MB/s  :)  [best 19MB/s]
SDR104 @ 96MHz : r:43MB/s w:18MB/s  W:19MB/s R:43MB/s  ::) [best 19MB/s]
SDR104 @ 96MHz : r:43MB/s w:19MB/s  W:18MB/s R:43MB/s  ::) [best 19MB/s]
SDR104 @ 80MHz : r:36MB/s w:17MB/s  W:17MB/s R:36MB/s  meh [best 19MB/s]
SDR104 @ 80MHz : r:36MB/s w:16MB/s  W:16MB/s R:36MB/s  meh [best 19MB/s]
SDR104 @ 120MHz: r:54MB/s w:18MB/s  W:18MB/s R:54MB/s  ::) [best 19MB/s]
SDR104 @ 120MHz: r:54MB/s w:18MB/s  W:18MB/s R:54MB/s  ::) [best 19MB/s]
SDR104 @ 132MHz: r:59MB/s w:18MB/s  W:18MB/s R:59MB/s  ::) [best 19MB/s]
SDR104 @ 132MHz: r:60MB/s w:18MB/s  W:18MB/s R:59MB/s  ::) [best 19MB/s]
SDR104 @ 160MHz: r:71MB/s w:18MB/s  W:18MB/s R:70MB/s  ::) [best 19MB/s]
SDR104 @ 160MHz: r:71MB/s w:18MB/s  W:18MB/s R:70MB/s  ::) [best 19MB/s]
Best: r:54MB/s w:18MB/s  W:18MB/s R:54MB/s  ::) [best 19MB/s]
Best: r:54MB/s w:18MB/s  W:18MB/s R:54MB/s  ::) [best 19MB/s]

Done.
Please run THOROUGH tests before using!!!

Kingston 64GB : 9 MB/s

Code: [Select]
Before the hack: r:22MB/s w:6.1MB/s  W:6.8MB/s R:22MB/s  8)  [best 6.1MB/s]
SDR50 @ 96MHz  : r:43MB/s w:9.2MB/s  W:8.2MB/s R:43MB/s  8)  [best 9.2MB/s]
SDR50 @ 96MHz  : r:43MB/s w:9.1MB/s  W:5.8MB/s R:43MB/s  ::) [best 9.2MB/s]
SDR50 @ 80MHz  : r:36MB/s w:8.9MB/s  W:12MB/s R:36MB/s  ::) [best 9.2MB/s]
SDR50 @ 80MHz  : r:36MB/s w:9.0MB/s  W:12MB/s R:36MB/s  ::) [best 9.2MB/s]
SDR50 @ 120MHz : r:err [SAFE]  [BACK]
SDR50 @ 120MHz : r:err [SAFE]  [BACK]
SDR104 @ 96MHz : r:43MB/s w:ERR [SAFE] !!! [BACK]
SDR104 @ 96MHz : r:35MB/s w:ERR [SAFE] !!! [BACK]
SDR104 @ 80MHz : r:33MB/s w:ERR [SAFE] !!! [BACK]
SDR104 @ 80MHz : r:33MB/s w:ERR [SAFE] !!! [BACK]
SDR104 @ 120MHz: r:err [SAFE]  [BACK]
SDR104 @ 120MHz: r:err [SAFE]  [BACK]
SDR104 @ 132MHz: r:err [SAFE]  [BACK]
SDR104 @ 132MHz: r:err [SAFE]  [BACK]
SDR104 @ 160MHz: r:err [SAFE]  [BACK]
SDR104 @ 160MHz: r:err [SAFE]  [BACK]
Best: r:34MB/s w:ERR [SAFE] !!! [BACK]
Best: r:34MB/s w:ERR [SAFE] !!! [BACK]

Done.
Please run THOROUGH tests before using!!!

Transcend 64GB : 11 MB/s

Code: [Select]
Before the hack: r:21MB/s w:11MB/s  W:20MB/s R:19MB/s  8)  [best 11MB/s]
SDR50 @ 96MHz  : r:22MB/s w:11MB/s  W:21MB/s R:21MB/s  :)  [best 11MB/s]
SDR50 @ 96MHz  : r:22MB/s w:11MB/s  W:10MB/s R:21MB/s  ::) [best 11MB/s]
SDR50 @ 80MHz  : r:22MB/s w:11MB/s  W:21MB/s R:20MB/s  ::) [best 11MB/s]
SDR50 @ 80MHz  : r:22MB/s w:11MB/s  W:11MB/s R:20MB/s  ::) [best 11MB/s]
SDR50 @ 120MHz : r:22MB/s w:11MB/s  W:21MB/s R:20MB/s  :)  [best 11MB/s]
SDR50 @ 120MHz : r:22MB/s w:11MB/s  W:11MB/s R:20MB/s  :)  [best 11MB/s]
SDR104 @ 96MHz : r:22MB/s w:11MB/s  W:11MB/s R:21MB/s  ::) [best 11MB/s]
SDR104 @ 96MHz : r:22MB/s w:11MB/s  W:21MB/s R:21MB/s  :)  [best 11MB/s]
SDR104 @ 80MHz : r:22MB/s w:11MB/s  W:21MB/s R:20MB/s  ::) [best 11MB/s]
SDR104 @ 80MHz : r:22MB/s w:11MB/s  W:11MB/s R:20MB/s  ::) [best 11MB/s]
SDR104 @ 120MHz: r:22MB/s w:11MB/s  W:11MB/s R:20MB/s  ::) [best 11MB/s]
SDR104 @ 120MHz: r:22MB/s w:11MB/s  W:11MB/s R:20MB/s  ::) [best 11MB/s]
SDR104 @ 132MHz: r:22MB/s w:11MB/s  W:21MB/s R:20MB/s  ::) [best 11MB/s]
SDR104 @ 132MHz: r:22MB/s w:11MB/s  W:21MB/s R:20MB/s  ::) [best 11MB/s]
SDR104 @ 160MHz: r:22MB/s w:11MB/s  W:11MB/s R:21MB/s  ::) [best 11MB/s]
SDR104 @ 160MHz: r:22MB/s w:11MB/s  W:11MB/s R:20MB/s  ::) [best 11MB/s]
Best: r:22MB/s w:11MB/s  W:21MB/s R:20MB/s  ::) [best 11MB/s]
Best: r:22MB/s w:11MB/s  W:21MB/s R:20MB/s  ::) [best 11MB/s]

Done.
Please run THOROUGH tests before using!!!

55
Reverse Engineering / Re: UHS-I / SD cards investigation
« on: April 04, 2018, 11:56:27 PM »
Quote
Ran a brute force (random) search for the above registers, and...

...what about brute force search registers for CompactFlash?  ;)

56
Feature Requests / Re: AWB without shift
« on: March 04, 2018, 02:08:04 PM »
Had the same problem, it's because auto-white-balance is standard set as a shortcut key.
In your case AWB still has shortcut key: "Foc Pnts" in LiveView (6D).

In my case AWB has shortuct key: "RATE" (5DIII). It is good. But mostly I press this button by mistake.

57
Feature Requests / Re: AWB without shift
« on: March 03, 2018, 11:38:54 PM »
I modified question :)

58
Quote
Can easily take months or years

Ok. Is it possible detect change ISO, aperture and shutter value? If yes, this hack could be work:

1. Save value (ISO, aperture, shutter) after all change by ML.

2. When is some value changed and does not equal to saved value (only for change by Canon code - Scrollwheel controls):
reset current value to saved value and set decreassed/encreased ML value.

59
Quote
Scrollwheel controls
It's not possible to remap them while recording. In standby, ML menu uses a trick: it opens some Canon dialog in background to steal wheel events from it, but this trick doesn't work while recording.

Can "log *ALL* MMIO reads/writes" be helpful for finding another trick?

60
Feature Requests / Re: "Scroll" HDMI output
« on: February 03, 2018, 12:34:50 AM »
Quote
Please, can someone help with implementing?

Hope dies last :-)

61
It would be possible add some shortcut key for crop mode?

(Button INFO is enough if it does not work otherwise.)

62
Thx! I will download next alpha version.

Quote
- delete selected video from session (e. g. Del)
When I delete some video, first video is always selected. It will be better select next video with nereast index ;)

63
Please, can you add more key shortcuts?
I used this key shortcut in unsupported application  MlRawViewer:
- Cut In/Out (e. g. Shift+I/Shift+O when 'I' is used for Info)
- go to previous/next video (e. g. K / J)

- delete selected video from session (e. g. Del)

64
Hardware and Accessories / Re: External monitor
« on: December 20, 2017, 06:33:44 PM »
Quote
no latency
Latency is not fixed. I think it is same as there:
Quote
https://youtu.be/pvC-_Kkxleg?t=6m14s

:-(

65
General Help Q&A / Re: Recording HDMI out to a video capture card
« on: December 20, 2017, 01:34:22 AM »
5D Mark III 1.2.3:
Canon menu: 'SET UP2' > 'HDMI frame rate': 24p

66
Feature Requests / Re: "Scroll" HDMI output
« on: December 19, 2017, 08:51:23 PM »
Quote
However, the feature you are looking for is really easy to do - just change the display buffer address (start from the full-screen magic zoom code or HDR video flicker workarounds, and tweak from there). Scrolling left to right should be straightforward; scrolling up and down will display additional things (likely noise), but if you can zoom on the external monitor, that should be harmless.
Please, can someone help with implementing?

67
Reverse Engineering / HDMI reverse engineering
« on: December 19, 2017, 12:30:21 AM »
Topic split from TFT SIO communication (tft_regs.mo).



I run "Brute-force all registres" on 5D3 v123 with HDMI monitor. No registrer change view on monitor (as could be expected).

Is it possible prepare some brute-force test for registeres that could be change view on HDMI monitor?

I am looking for some alternative for magic-zoom on HDMI monitor
(e. g. "Scroll" HDMI output: http://www.magiclantern.fm/forum/index.php?topic=18488.0).

68
Camera-specific Development / Re: Canon 5D Mark III / 5D3 / Firmware 1.3.4
« on: November 13, 2017, 05:53:01 PM »
Works this firmware with MAGIC_ZOOM_FULL_SCREEN ?

69
Modules Development / Re: MLV Lite
« on: October 07, 2017, 11:11:57 PM »
Quote
Are you talking about previewing in the camera in the Canon "Play" mode?
Yes. All thumbnails are black... This is problem.

70
Modules Development / Re: MLV Lite
« on: October 07, 2017, 07:25:41 PM »
Quote
It is black until you press play, then the movie will preview in camera.
Yes, I knew that. I usually shoot hundreds videos files... all will have a black previews. This is not usable.

Sometimes I do not need to record the sound. But I always need quick preview..

71
Modules Development / Re: MLV Lite
« on: October 07, 2017, 05:23:24 PM »
How can I disable black frames in H264.proxy?

Video preview in Play mode is black, because first frame is black :-(

72
Modules Development / Re: MLV PLAY (mlv_play.mo)
« on: June 28, 2017, 12:16:07 AM »
Thx for add lossless playback support inside camera.

Do you know some alternative for Windows?

73
Can you just download the latest mlv_dump from experimental page (not sure if it's the same tho): https://builds.magiclantern.fm/jenkins/job/crop_rec_4k/19/artifact/modules/mlv_rec/mlv_dump.exe

and replace it with the mlv_dump that's inside the package content within MLRV?

Sorry wish I could be more of help in here but hopefully a Windows user will come on board and confirm this.

MlRawViewer (windows version) does not contains mlv_dump.exe.

74
Today I had crash during record:

CRASH00.LOG
ASSERT: IsSuiteSignature( hSuite )
at ./PackMemory/PackMem.c:983, task MoviePlay
lv:0 mode:3


Magic Lantern version : crop_rec_4k.2017Apr29.5D3123
Mercurial changeset   : d55423f1e270 (crop_rec_4k) tip
Built on 2017-04-29 14:31:28 UTC by jenkins@nightly.
Free Memory  : 164K + 3811K

ASSERT00.LOG
ML ASSERT:
fullsize_buffers[1] == UNCACHEABLE(raw_info.buffer)
at mlv_lite.c:1379 (free_buffers), task raw_rec_task
lv:1 mode:3


Magic Lantern version : crop_rec_4k.2017Apr29.5D3123
Mercurial changeset   : d55423f1e270 (crop_rec_4k) tip
Built on 2017-04-29 14:31:28 UTC by jenkins@nightly.
Free Memory  : 144K + 3821K

Info
I used H.264 proxy (H264->SD with ML; RAW 1920x1080 12-bit->CF)

Magic Yoom Large TL 3>1, Waveform small, Red Crossout, DIGIC peaking: Slightly sharper, Zoom with old button..

75
Feature Requests / Re: ND filter instead reflex mirror
« on: April 30, 2017, 11:31:51 PM »
The mirror is stuck on to an opaque piece of plastic, with only a hole in the middle, so could work for 3x crop maybe
:( This is bad news.

In my link replaced only focus screen. Not reflex mirror. Sorry for mystification.
Replace mirror probably require disassemble all camera :(

Pages: 1 2 [3] 4 5