Messages

I don't think anyone has mentioned it so far: the reported 20MB/s results are what happens when a card fails to overclock.  The cam drops back to a slow, safe default (this is not ML but the cam / card itself).

With this card, you may get higher benchmark results if you disable all overclocking.

Ah! Brilliant. I deactivated the module and indeed, now it works better. At least I have the factory potential...

Thanks!

You didn't do anything wrong regarding camera/ML settigns. Try lower frequencies like 160 and 192 MHz, might work with your kingston card.
Anyway, Kingston Canvas Go! cards are not recommended with our current SD Ovreclocking version until someone figure out how to make it work.

Thanks for getting me back. OK, I got it. It's 'good' to know that it's not my or my camera's fault but a 'tough' card's 'fault' that cannot be overclocked.

Right after I sent my previous comment, I tried the card at 192, but got the same result.

The new card however, that I ordered, is on your list, so it should be fine.

Thanks

Something went wrong, have two same Micro sd's and it can easy get around 78 mb/s when I'm recording

@pepper_chip

Hi,

Thanks for your reply too. The fact that you wrote about the micro version of this sd card (from the same brand) should not effect speed, I mean yours and mine should work at pretty much the same speed. But, unfortunately, it's not the case. So far no clue what the problem might be. I'm waiting for a new card (ordered online) from a different brand, and will see the difference.

Thanks

[outdated]

@LesV

The SD card you are using "Kingston CANVAS Go!" was tested before and it doesn't work fine with SD Overclocking (see first post).
However sd_uhs version in crop_rec_4k.2022May25.700D115 build is outdated, download the latest sd_uhs version from first post, replace the old sd_uhs.mo with the new one.

Or use crop mood build which include latest sd_uhs too (I will no longer maintain my old 650D / 700D builds).

Test 160, 192 and 240 MHz with the latest sd_uhs then feedback please.

@theBilalFakhouri

Hi, thanks for the super quick reply. Apologies, I had a very busy day yesterday and I wanted to try also what you advised me to. I didn't mention that for test, I used already THAT sd_uhs module you recommended. I combined it with the build I mentioned.

Now I installed the latest build (see the image on the link below) but got exactly the same result. Absolutely disappointing (not the build!). I also watched your video (Crop mood - Build Walkthrough) on YT and tried to apply the same settings you were doing but I couldn't completely (vid resolutions). The raw video options I can only choose, getting green (that is working continuously and properly), are just ridiculously poor and at very low bit rates. 

The benchmark result: https://drive.google.com/file/d/1FCzVvijUBFPP7G_NO-AdAnqbLNquNhbW/view?usp=sharing

Is there ANY chance that the camera itself (by a setting I might have done somewhere) can cause this poor result? For goodness sake, the actual speed is only the half of the factory maximum. Or can my Kingston SD be faulty?

Any other ideas?

I already ordered another one (SanDisk Extreme Pro 128GB 200 MB/s) because I need more storage capacity anyway. Once I have it, will run a test, and will confirm if it works as it expected.

Thanks a lot.

Hi guys,
Could you help me to understand why my sd card's performance is so poor? Can I do something (different settings) to reach that level I can see on the images above? Or I should buy a new one from the list you refer above?

The camera: Canon EOS 700D
The build I'm using: crop_rec_4k.2022May25.700D115
The SD card: Kingston CANVAS Go! Plus, 128 GB, 170 MB/s, U3, V30
Please have a look at the link below. The result is shockingly poor, even though overclocked it according the description in here, setting it to 240MHz.

Thanks in advance.

https://drive.google.com/file/d/158xEtdns-19YnRmXdtTX3a04hkZdicqT/view?usp=share_link