Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - rockyrocky

#1
Camera Emergency Department / Re: 6D bricked?
July 12, 2021, 06:03:27 PM
Quote from: Levas on July 12, 2021, 05:58:11 PM
Not sure if you googled on err80 canon, but some say it happens due dust behind the memorycard door, maybe some dust shorting some pins ?

Other say you should try deattach and reaatach the lens(see if something is wrong with those metal contact pins.

Before going to Canon I would try some of the stuff found by googling err80 Canon.

Thank you. Camera works extended time with no error, when liveviews is off. Even with SD card in
#2
Camera Emergency Department / Re: 6D bricked?
July 12, 2021, 05:31:53 PM
Quote from: kitor on July 12, 2021, 09:07:59 AM
https://support.usa.canon.com/kb/index?page=content&id=ART102961

ERR80 comes from MPU so it's most likely a hardware failure, not related to Magic Lantern.

I don't think we have a way to even pinpoint error source for ones coming from MPU.

So, Should I go to Canon store to fix hardware failure?
#3
Camera Emergency Department / Re: 6D bricked?
July 12, 2021, 05:28:05 PM
Yeah, with no SD card err 80 still occurs. LiveView works
#4
Camera Emergency Department / Re: 6D bricked?
July 12, 2021, 07:09:58 AM
Same with another card. Camera works fine for few minutes. Then err [80] occurs, screen freezes
#5
Camera Emergency Department / Re: 6D bricked?
July 10, 2021, 04:20:22 PM
It shows up err [80]
#6
Camera Emergency Department / Re: 6D bricked?
July 10, 2021, 04:19:43 PM
Quote from: Walter Schulz on July 09, 2021, 09:39:05 AM
Try
Remove battery, insert fresh PC-formatted card. Startup.
Oh. Camera froze again. With formatted card. What should I do?
#7
Camera Emergency Department / Re: 6D bricked?
July 10, 2021, 04:17:24 PM
This turned on the camera
#8
Camera Emergency Department / Re: 6D bricked?
July 09, 2021, 01:32:04 AM
Quote from: Walter Schulz on July 08, 2021, 10:14:15 PM
Clean install:
Format card in cardreader
Format card in cam
Copy extracted build content to card
Run firmware update

Revised shutdown procedure:
Turn power off
Wait at least 5 seconds
Open battery compartment and remove battery
Remove card.

Try to follow revised shutdown procedure and report back if damage occurs again.

Ok, I did that with EOSCard. Camera is working. Than everything happened again
#9
Camera Emergency Department / Re: 6D bricked?
July 08, 2021, 10:42:45 PM
How could I format card in cam if it wont turn on?
#10
Camera Emergency Department / Re: 6D bricked?
July 08, 2021, 09:42:39 PM
I also noticed error 80 and this:
Boot flags: FIR=0 BOOT=-1 RAM=-1 UPD=-1
ROMBASEDDDR: 0xFF0C0000
#11
Camera Emergency Department / 6D bricked?
July 08, 2021, 09:34:43 PM
Hey! My 6D won't turn on. I have been using 6D with ML for 4 years without any problem and this is what happened:
1. I was adjusting the white balance through the ML main menu and at that moment my screen turned pink and froze
2. The LED light turned red and glowed for a long time. The switch did not work
3. I took out the battery and since then my 6D is not responding to anything
4. I found a1ex diagnostic tools and my camera turned on
5. I tested it and everything froze again
6. I installed a different firmware (I used firmware from Levas). Then the camera began to work without freezing.
7. I downloaded the firmware from Levas again and installed it to use all the custom settings
8. The same thing happened, but now autoexec.bin does not wake up my camera and it does not react to anything AT ALL
What can you recommend? I really hope for your help. Thank you for your time and attention