Messages

well i bought a new top assembled for my canon...

removed the old one and replaced with the new one.

When i turned on, the display was working and the cam was asking me to insert the actual date. And then the display goes off and never appeared again.

i have no idea what to do... i have this log:

http://pastebin.com/raw/B3FnSdLk

So.... i couldnt work to get the camera do work yesterday (i had to euthanize my dog, she was in severe pain with an lymphoma... if you wanna see her i made an small video with her here).

Anyhow... i did some further disassemble today and im almost sure the problem is in the top buttons as you can check here when i push and shake the main dial eventually the cam works for a while there.

So i disassembled again the also disassembled the top part to try to see if anything was loose or broken, i think the problem is mechanical... But couldnt get it to work... i ordered one replecement part (the whole top part) when that comes i will assemble it and then share if the problem is solved.

The strange part was the last time i turned on the cam this was the log i got:
http://gdurl.com/1J37

I did some disassembling and checked the cables that where visible after just removing the cover...

but still nada, i will try, another day with more time, to "fully" disassemble...

thank you for your assistence

disassembling

So, try and error and i find out that commit c5f48d5 is the one preventing me to run dm-sys actual revision in my 600D...

I dont know much about programming so what i try to solve this was to run:

Code Select Expand

hg backout -r c5f48d5

And then after compilling the newer revision i could get this LOG:

http://pastebin.com/Gty4rWeP

a1ex have been helping me, thanks again.

I was trying to get an log file with dm-spy but wasent beeing able to.

What i did was:

Edited features.h in plataform/600D.102  to look like this:
http://pastebin.com/yiB8cRhZ

Then i tryed to go back in time and to find a revision working with my cam, "hg revert -r ad6c903 --all" did the job and i got this log:
http://pastebin.com/kmKQmQWZ

ps. if i can i will try to find out in which revision of dm-spy my cam stop to produce an log file.

I have been using ML for quite a while today something happened and now my canon is almost dead.

When i turn the camera on nothing shows on the screen.

Here's what i have done:

Switch camera Off, remove: battery, card and lens.
Reattach lens, close card slot, reinsert battery and switch camera On again

No good all the same...

Restart camera without any card

Still nothing working...

rename /ML/SETTINGS/MAGIC.CFG to ML/SETTINGS/MAGIC.BAK
restart camera (default settings start-up)

Nop...

Try to start up the camera in every dial mode

When i did that with SD card nothing happpened but without the SD card in CA mode the panel showed up but then dead again just a few sec. on...

Got a new SDcard formated in PC, used EOSCard to set the bootflag and then copyed ML folder, autoexec.bin and 600D-102.fir

no good...

Deleted the files from the card and then copyed new ones i just downloaded

nop...

Portable display test

Startup log

You can get a very detailed log about Canon boot process by compiling the dm-spy-experiments branch.

Im trying to do that but i cant... i compiled the dm-spy-experiments branch and copyed the autoexec.bin when i reboot the camera with this card im getting 3 paused led blinks and 3 fast ones infinitely not sure if im doing somthing wrong here...

I have the ROM0.bin and ROM1.bin from my SDCARD here (link removed).

Please if you can help me i would apreciate very much.