Yes)
Etiquette, expectations, entitlement...
@autoexec_bin | #magiclantern | Discord | Reddit | Server issues
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Show posts MenuQuote from: g3gg0 on July 02, 2017, 05:04:31 PMYes
header start looks a bit uncommon.
[MLVI]
[RAWI][INFO][RTCI][EXPO][LENS][IDNT][WBAL][STYL][VERS]+++++[EXPO][LENS][RTCI][EXPO][LENS][WBAL]
[VIDF][NULL]
[VIDF][NULL]
[VIDF]...
is this recorded with mlv_rec instead of mlv_lite?
Quote from: g3gg0 on July 02, 2017, 09:22:32 PM
mlv_lite is a cleaner rewrite of mlv_rec with all knowledge of it with additional new findings.
so yeah, it will take over and be the raw recording module.
Quote from: g3gg0 on July 02, 2017, 06:27:04 PM
can you check if you had a lot of .idx files on your card that wasn't able to play back?
Quote from: a1ex on July 02, 2017, 01:20:07 PM
Can you upload a small file that can be replayed in the older version, but not in the newer?
Quote from: a1ex on July 02, 2017, 12:09:45 AM
Except for some asserts that pop up the console after a few seconds of playback, it works fine here. Solved the asserts - they were related to the fix for this issue.
Quote from: Darkloyd on June 26, 2017, 10:49:47 PMYes 1.2.3, SmallHD 501, mlv 67, 39, 24 fps, standart settings, nothing special)
Nice !!!
You use the firmware 1.2.3 ?
You record this movie in 60p ? Mlv or H.264 ? if mlv what is your settings ?
What's your monitoring ?
Great Thx.
Quote from: D_Odell on June 25, 2017, 11:31:04 PM
Nice to see your shots again Were you able to frame while shooting cropped?
Quote from: Danne on December 18, 2016, 08:34:18 PM
Some short samples of 10bit, 12bit, 14bit filmed with a 5D mark III
10bit MLV(mlv_lite)
https://drive.google.com/file/d/0B4tCJMlOYfirYUJxZ0JPVzJsX0k/view?usp=sharing
12bit MLV(mlv_lite)
https://drive.google.com/file/d/0B4tCJMlOYfirckp3bFBqanNmbXc/view?usp=sharing
14bit MLV(mlv_lite)
https://drive.google.com/file/d/0B4tCJMlOYfirM1loSU9sYWxHeW8/view?usp=sharing
Quote from: reddeercity on February 05, 2017, 07:52:20 AM
Thanks @a1ex
Ok I think I got my head around this a little better ,
raw.c- line160I see "0xC0F08114" etc.... stuff , question; with the "#ifdef CONFIG_DIGIC_V" then it has #else , does (#else) mean Digic4
or would it make a difference to call "#ifdef CONFIG_DIGIC_IV" or is that a way of writing less code ?
As I see how other newer cams are configured does there need to be a "#ifdef CONFIG_xxx" for the 5D2 ?
maybe like this ?#ifdef CONFIG_5D2
#define PACK32_ISEL (3)
#endif
From the Register Map "PACK32_ISEL" has 1-15 selectable variables
Would be right to put that variable in brackets ?
Or does "PACK32_ISEL" need to "#define" at all ?
Not sure how to write the Code/Syntax
Close you think , or way off base here .
Edit:
Because there 15 different variables does that mean the only way to figure it out is by trial & error ?
Quote from: ricbi1 on January 04, 2017, 09:14:27 PM
Did some tests on 5d3 and like others have reported 10bit works great in non-crop mode. I also pushed FPS to 60 at full HD and stopped recording at 1min + at 2:35 aspect ratio.
Really impressive!
Looking forward to doing more tests.
Recording to KomputerBay x1000 64gb
Quote from: DeafEyeJedi on December 24, 2016, 04:46:20 AM
https://bitbucket.org/daniel_fort/magic-lantern/downloads
Page created in 0.113 seconds with 13 queries.