Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Avenger 2.0

Pages: [1] 2
Camera-specific Development / Re: Canon R5
« on: August 21, 2020, 08:20:49 AM »
Looks like if you take out the backup battery the overheating timer resets and you have full record time :o

General Chat / Re: Advice? - R6 vs A7SIII
« on: August 03, 2020, 08:40:27 AM »
Looks like those R5/R6 even overheat when taking pictures  :-X
Have more trust in ML on my 5D3 at the moment 8)

General Chat / Re: Advice? - R6 vs A7SIII
« on: July 30, 2020, 12:53:07 PM »
Actually, it may be not true. Due to several experiments Sony overheat even faster than R5 in 4K60 mode.
Unfortunately the R6 overheats in all modes. Don't think this will ever be fixable in firmware. Better to buy a EOS R instead for video (or go the Sony route).

Will your LCD work without ML? If not, sounds like a hardware problem to me. Dead LCD panel of controller chip.

Camera-specific Development / Re: Canon 600D / T3i
« on: February 18, 2017, 07:26:19 PM »
You'll have to downgrade to 1.0.2 first before you install ML.

Camera-specific Development / Re: Canon 60D
« on: January 10, 2017, 07:46:12 AM »
I need some help!! My camera keeps saying "Incorrect firmware version. Expecting firmware version 1.1.1" I have 1.1.2. Will it not work with 1.1.2? And if it does still work, can you give me help with how to install it properly as I'm not sure if I'm doing it correctly XD
You need 1.1.1. You can just put it on the SD card and run firmware update to downgrade to 1.1.1.
Found working 1.1.1 link on google:

Camera-specific Development / Re: Canon 7D Mark I
« on: December 31, 2016, 09:29:46 PM »
Has something changed for 3x crop h264 video in 3 Dec nightly? I can't find the setting anymore to enable it.
Edit: I guess I was mistaken and it was never possible on 7D...

General Development / Re: 50D and 7D DUAL_ISO in MOVIE mode PORTING thread
« on: December 30, 2016, 09:04:09 PM »
Anyone know if this also works for the 7D?

Camera-specific Development / Re: Canon 600D / T3i
« on: December 07, 2016, 04:22:43 PM »
You will have to downgrade to v1.0.2.

Reverse Engineering / Re: EF communication protocol
« on: November 26, 2016, 11:03:51 AM »
Nice thanks, finally those french lessons will start paying off  ;D

Camera-specific Development / Re: Canon 600D / T3i
« on: October 14, 2016, 08:31:00 PM »
The last nightly build will be way more stable than v2.3.
A lot has changed since then (headphone monitoring, audio controls, etc...)
Best to try it out on a spare sd card, but I promise, you will not want to get back to v2.3  ;)

Camera-specific Development / Re: Canon 7D
« on: August 19, 2016, 04:39:45 PM »

I've just saw that maybe ML is available to Canon 7d Mk2:

Is this for real? Or this build is for 7D Mk1 ?

7d203 is magic lantern for 7d 2.03 firmware.

Camera-specific Development / Re: Canon 7D
« on: August 12, 2016, 06:36:21 PM »
I would like to know if there are plans for a nightly build for 2.0.5 firmware?
If I remember correctly there were no significant changes between 2.0.3 and 2.0.5
Not sure why it is not build for 2.0.5. Maybe something internally changed that requires a lot of work?

Are you shooting at a high iso? I would not go above iso 640/800 for h264 video.

Camera-specific Development / Re: Canon 7D
« on: July 31, 2016, 08:54:11 AM »
Raw video or canon h264 video? For raw video (on a budget) I would go for 7d. For h264, 600D/60D if audio controls are important. Otherwise 700D. Also not a pro...

Camera-specific Development / Re: Canon 600D / T3i
« on: April 22, 2016, 03:53:23 PM »
Thanks A1ex!

Modified first post to reflect new install procedure.

General Chat / Re: Will Canon ever have 4k in their mainstream DSLRs?
« on: February 16, 2016, 10:17:45 AM »
Canon 80D specs leaked, but no 4K, only 1080p 60fps  :-[

Camera-specific Development / Re: Canon 600D / T3i
« on: January 14, 2016, 04:29:49 PM »
Thanks, very good explanation.

magic lantern-Nightly.2016Jan12.600D102 not work on canon EOS 600d. LED blinks continuously.

Maybe the new 2016Jan14.600D102 nightly works? But it looks like the filesize has increased significantly since 2016Jan12.600D102.
Have you tested without modules enabled? Does this also give problems?

Camera-specific Development / Re: Canon 600D / T3i
« on: January 14, 2016, 06:37:04 AM »
Has the 600D less memory then the 550D? Or just less free memory because of heavier canon firmware?

Camera-specific Development / Re: Canon 600D / T3i
« on: September 10, 2015, 08:34:15 AM »
Thanks, will give it a try.

Who do I have to email/PM to get the link on the build page to link to the new maintainer thread?

Camera-specific Development / Re: Canon 600D / T3i
« on: June 16, 2015, 03:06:59 PM »
I'd also like to maintain this thread. I've been around the forum for almost 3 years now and my 600D is still ticking and still running Magic Lantern. So let's DO THIS THANG!
Thanks  :) Same here, using ML almost 3 years now, but only recently moved to the nightly builds. And glad I did, because the new builds are just so more stable and feature-rich.
Let's kick this camera support back to life and get the new nightly builds we all love  8)

I've created a maintainer thread for the Canon 600D, since I have two 600D camera's to test on and have been using ML for some time now.
I'm planning to be more active on the forum and hopefully this will result in new nightly builds for the 600D :)

Camera-specific Development / Canon 600D / T3i
« on: June 16, 2015, 10:00:13 AM »
Magic Lantern for the Canon EOS 600D/Rebel T3i

Magic Lantern User Interface animation
  • An overview of the user interface with Magic Lantern installed
  • User controllable

Install Guide
  • Step by step instructions to get Magic Lantern installed on your camera
  • Includes troubleshooting and useful notes

600D/T3i build page
  • Correct Canon firmware version to run Magic Lantern can be found here
  • Lots of useful links and information

Feature matrix
  • List of Magic Lantern features that work on the 600D/T3i
  • Link heaven

Frequently Asked Questions
  • Common questions regarding the Magic Lantern project
  • If you have a question, check here first

User Manual
  • Needs work
  • In camera, in the Magic Lantern menus, all options have a short one or two line help text at the bottom of the display

General help

Original post
Code: [Select]
[size=14pt][u]Magic Lantern Installation & Updating Guide[/u][/size]
[u][size=12pt]for Canon EOS 600D/Rebel T3i[/size][/u]

This guide will help you install and update your Canon EOS 600D/Rebel T3i to the lastest Magic Lantern Nightly builds.
[size=8pt][color=red]Warning! Magic Lantern is not approved nor endorsed by Canon in any way, and using it will probably void your warranty. We are not responsible for any damages to your camera.[/color][/size]

[u][size=10pt]Before you start:[/size][/u]
- Make sure your battery is fully charged.
- Remove unnecessary accessories (battery grip/flash/etc).
- Have a sd card reader or laptop with integrated sd card reader.
- Use a sd card of 32GB or smaller for first install.
- Understand that you may lose your warranty and brick your camera.

[u][size=10pt]Updating Canon firmware:[/size][/u]
- Make sure you are running Canon firmware v1.0.2 before you install ML, if you are you may skip this step.
- If not, download it [url=]here[/url].
- Follow included instructions and update your camera.

[u][size=10pt]Magic Lantern Install:[/size][/u]
- Download the last nightly version [url=]here[/url]
- Format your SD card in camera first, then put it in your SD card reader connected to your PC.
- Unzip 'ML' directory, 'autoexec.bin' and 'ml-setup.fir' from the downloaded ZIP file onto your sd card.
- Put your sd card in your camera, switch camera to M-mode and power it up.
- Launch firmware update and install ML.
- After the green confirmation screen, turn off your camera.
- Power your camera back up and enjoy Magic Lantern!

[u][size=10pt]Updating Magic Lantern with new build in the future (on camera and sd card with ML installed):[/size][/u]
- When new nightly is available (see [url=]here[/url] for last build), download it onto your PC.
- Put your sd card (running the old build) into your PC and delete (NO format!) the 'ML' directory and 'autoexec.bin' file.
- Extract the content of the zip from the new build onto your sd card.
- Repeat this process for all sd card with old ML builds you want to update.

[u][size=10pt]Uninstalling Magic Lantern from SD card:[/size][/u]
- You cannot simply delete the files from the sd card to uninstall ML from it (as the boot flag will remain set).
- Format the SD card in the camera (select this option: Format card, remove Magic Lantern).

[u][size=10pt]Uninstalling Magic Lantern from camera:[/size][/u]
- You cannot simply reinstall the canon firmware to remove ML.
- With a ML sd card, launch the Firmware Update process and follow the instructions on-screen to uninstall ML.

[u][size=10pt]Boot without loading Magic Lantern:[/size][/u]
- If you want to boot your camera without ML, all you have to do is hold down the "SET" button while switching your camera "ON".

[u][size=10pt]Updated user Guide for ML nightly builds:[/size][/u]
- [url=]User Guide[/url]

[img width=300][/img]

Edit: Modified install procedure for new nightly and installer.

Pages: [1] 2