Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - BlueBomberTurbo

#1
General Help Q&A / Disable ERR Beep & Debug Log?
January 07, 2019, 05:20:56 AM
I've got a 5D Mark II that needs a shutter replacement.  Eventually.  Just using it as a daily driver photo camera with the benefit of Dual ISO for extra DR.  Every image I take results in an ERR 30 that can easily be cleared by tapping the shutter button, then I can shoot again.  But with ML, it beeps, and saves to a debug log.  This adds a few seconds to the time between images, and of course, causes an annoying beep.  Is there any way to disable either/both of these?
#2
Tragic Lantern / Re: Tragic Lantern for EOS M
September 30, 2013, 03:51:05 PM
Quote from: jerrykil on September 30, 2013, 03:32:30 AM
Same for me. I'd love to see fixes to ETTR and advanced bracketing
Hmm, not sure how it's supposed to work when it's working properly, but normally, mine would adjust exposure 3-4 times, bright -> dark -> bright etc.,  before settling on the final correct one.

On a happier note, looks like the newer builds actually work with Dual ISO!  For whatever reason, [EOSM]FullbackADTGui wouldn't encode the CR2 properly, and would throw errors in CR2HDR.
#3
Tragic Lantern / Re: Tragic Lantern for EOS M
September 29, 2013, 10:04:13 PM
Only been trying the nightlies since 9/26, but I seem to be getting a lot of "Expo Limit Reached" errors when using ETTR.  Nothing specific seems to trigger it.  Never had it happen once with the original ML version I started off on, [EOSM]FullbackADTGui.  At worst, that only had a few "Whoops" errors, but the biggest issue is that ETTR won't work again unless I take a photo or restart the camera, and that doesn't guarantee that the exposure limit error won't just come right back.  Any ideas?
#4
Hmmm, can't even get the Dual ISO module to work on that...
#5
General Help Q&A / Re: Noob advice on Bitrate in h.264
September 15, 2013, 02:54:47 PM
Technically, all it will do is reduce compression artifacts.  As far as how it might affect color correction, if the video is compressed enough to cause blocking, reducing compression will make things look a bit better, but nothing dramatic like RAW video.  At best, it'll make high ISO video easier to apply noise reduction to, since that's where compression will appear at its worst.
#6
Been trying all different versions of cr2hdr.exe and dcraw.exe, and everything I try comes back with the same messages:


QuoteT:\CR2HDR>cr2hdr DUAL0398.CR2

Input file     : DUAL0398.CR2
Canon EOS M detected
Full size      : 5280 x 3528
Active area    : 5208 x 3476
White level    : 12500
Black borders  : 72 left, 52 top
Black level    : 1987
ISO pattern    : BdBd RGGB
Interlacing method not supported
ISO blending didn't work


Here's one of the many files I've tried, if someone could test it out and let me know if it works for them:
https://dl.dropboxusercontent.com/u/15557216/DUAL0398.CR2

Running [EOSM]FullbackADTGui version of ML on firmware 2.02.
#7
Tragic Lantern / Re: Tragic Lantern for EOS M
September 12, 2013, 06:46:43 PM
Quote from: gary2013 on September 12, 2013, 04:32:37 AM
Sometimes I have problems and it eventually clears up after maybe four attempts of off-then back on. Make sure you wait a few seconds for the red flash led to appear by the on/.off button. I had a problem an hour ago installing thet latest build posted here and the modules were not loading. They were always showing an Err for each module. After four attempts of turning them on,etc. it finally worked correctly and all modules loaded up saying OK. I had this module loading problem before maybe three or four weeks ago.

Don't forget you are suppose to tap the LCD display with two finger tips at the same time to get into the ML menus.

Gary
Finally got it working!  Thanks!
#8
Tragic Lantern / Re: Tragic Lantern for EOS M
September 12, 2013, 04:24:45 AM
Anyone else having this issue when installing?  Everything seems to go perfect, but after I get the install confirmation (green text screen) and restart, it just goes back to the normal interface.  If I cycle through the Info displays, one will be ML's, but no ability to do anything with it.  Same in video.  There's no ML menu available at all, so I really can't do a thing with it besides watch the zebras.  I'm following the instructions from post 1496  from p.60, with a camera with 2.02 FW from the factory.