Messages

Hi,
I have Sandisk ultra 80MB/s card in my 6D.
I can record only 5 sec in 1728x972 resolution.
Can me help somebody why is it?

THX!
-széna

Hello again...

No RAW video option in my video menu. What I do wrong?
SD card is sandisk ultra 32 mb/s 80mb/s - is it enought?

THX!
-széna

...

THX!

OK, I'm a beginer - I think it's a really useful information for beginers. It should to write the end of the install info maybe...

Thank you again Walter!

Hi All,
I need some help please.

1, I updated my canon factory firmware from 1.13 to 1.1.6
2, I Formated the SD card and copied the 3 pieces of ML 116 file
3, I updated canon factory firmware 1.1.6 to ML 116

It's wrote - It's DONE - please restart... etc...

I restarted but there is the canon menu again! No any ML menu only changed the SD slot red led flash in every 5-10 second...

What is the problem?

Thank you!
-széna

6D hasn't broken any cards on me... but 600D has broken 2.

Card goes in, things seem fine.. a few writes + reboot later, unable to read card.

Sector 0 is toast and card no longer reads in anything except @ low level (i.e recovery software). No way to format it because as soon as you remove the card the sector goes back to being corrupted.

oops... does it means I can throw away my card?

Ohh GOD!
I was took photos about full moon on the top of a huge building last night. This morning I put SD card to reader and doesn't works... I tried in osx, win, and 6D too. nothing...

Hi,
you might want to take a look at this chart - http://blog.planet5d.com/wp-content/uploads/Twitter-_-autoexec_bin_-Updated-raw-chart-still-need-....jpg

You need a card that is able to write data @45Mb (a Sandisk extreme is recommended) - 1592*896 is reported to be continuous  @24p

THX!

I think your card is not that good (if you've used that 4GB) to support raw recording. You'll need to use a fast SD card.
The reason to use a 4GB card was for the sole purpose of installing ML on your camera, you'll need to prepare another card with all the files specified.

What is the highest resolution and bit rate what can I set in safe for making raw videos?

I think your card is not that good (if you've used that 4GB) to support raw recording. You'll need to use a fast SD card.
The reason to use a 4GB card was for the sole purpose of installing ML on your camera, you'll need to prepare another card with all the files specified.

I used 4GB card only for "installing".
I formated my 64GB ultra sandisc (30mb/sec) to try making raw videos.

Just buy a super cheap 4GB card or something just to do the install. I'm pretty certain that using the 64GB card is your problem man Good luck!

Hello again!
So, I bought an 4 GB card and I can "install" ML on my 6D!
But...
There is something problem I think... At button Q - ML menubar is gone - it's OK. But if I set raw video the 6D go crazy. ML send lot of messages and this box not gone. It's cover half of screen and infos are flashing and I can make only 1-2 second long raw videos.
The red card reading light is flashing constantly too. is it normal?
Finally I have err 70 message and I have to switch off my camera.
http://kepfeltoltes.hu/130819/422121288image_www.kepfeltoltes.hu_.jpg

Just buy a super cheap 4GB card or something just to do the install. I'm pretty certain that using the 64GB card is your problem man Good luck!

OK I will!
Thank you very much!

That might be your problem. Do you have a card that isn't 64GB?

uhhh... no, but I will buy tomorrow.

What SD Card are you using dude?

SanDisk 64GB ULTRA 30MB/s it's SDXC I

Which firmware version do you currently have installed dude?

I didn't updated firmware - so I have 1.1.2

I made STEP 4, it's OK. But that's all.

Thank you for your quick answer noisyboy!

Hi Guys,
I'm in trouble...
I try to install ML to my 6D but I jammed at STEP 7!
I put the sd card and I try to update the firmware but camera say:

Update file cannot be found.
Please check the memory card reload the battery and try again.

I do everything when noisyboy wrote (formated card, I copy the files: folder ML, file 6D-112.fir and autoexec to the route directory etc...)

HELP ME PLS!

THX!
-széna