I am using a 6D with firmware 1.1.3 and have set up Motion Detection with Trigger - Frame Diff, Trigger level - 1, Detect size - small on Manual mode, focus switched off at lens. When I flick my hand over the lens nothing happens. Have I missed an essential step? Thanks for help. Alan T
hi i am trying to find out about Motion Detection my self if you look around youtube there are a few things
but they are in German & Spanish
or look at Magic Lantern v2.3 - User's Guide wiki.magiclantern.fm/userguide
hope it helps
Thanks, I have looked at Youtube and at the Userguide and I think/hope I have done everything right. But it still doesn't work. Must be missing one vital step?
Alan
Begin with
M mode, Liveview, MF
Motion Detect -> Trigger by Expo. change. Don't change defaults.
Motion Detect ON
Does cam trigger if you put your hand in front and move it away?
Thanks, changed trigger setting to "Expo change" - shutter fires now when I pass my hand over the lens or when I move the camera.
Thanks for your help.
Alan
Change trigger to frame diff.
Cam should trigger if you're panning. Does it work?
Tried changing trigger to Frame diff - shutter does not fire, either when panning or moving hand across lens. I want to use the motion detect to photograph birds and thought that Frame diff would be the most likely setting. However, expo will do for now.
Thanks
Alan
Hi,
I just tried this to confirm.
The 'Expo change' setting works fine, but I can't get the other two modes to work.
'Frame diff' produces an empty black square on the screen, but apart from that nothing happens and 'motion level' remains '0' while panning.
'Steady hands' seems to do nothing at all at first, no detection square, just the usual Live-view screen. But if I press half-shutter the black square and 'Motion level: 100' appear. The camera then starts to take pictures at regular intervals. But it makes no difference if I keep the cam steady or not.
So I guess it's a bug :)
Thanks for your test!
Little test routine:
- Backup ML directory (esp. Settings dir)
- Prefs tab -> Config files -> Restore ML defaults
- Restart cam
- Enter Liveview and make sure to have exposure settings showing up some scene well lit
- Leave LV and enable "Frame diff".
- Press half shutter
-> Cam has to enter liveview on its own and must (!) take a pic if frame detection sets in.
Possible results:
- Cam entering LV but frame detection fails. Numbers on screen changing at all?
- Cam works as designed, taking a shot.
Please report back.
Hi,
Just followed your directions and here are the results:
The cam directly enters LV after I enable 'Frame diff' and press the garbage can to close ML menu. I don't even have to press half-shutter.
The black detection area shows, and 'Motion level: 0' top left. This doesn't change and the cam doesn't take any pictures.
When I try to stop LV, it immediately enters LV again. I have to disable 'Motion detect' to get the cam out of LV.
Hope this helps!
Regards,
Ray
Thanks! Found out there is an issue open at Bitbucket covering same error:
https://bitbucket.org/hudson/magic-lantern/issues/2418/frame-difference-motion-detection-always
Will add something there.
There seems to be a problem, however: 6D looks like "blindly maintained".
Ok, great, you're welcome.
I'll keep an eye out to see how things progress and can/will do more tests if needed.
Hi,
I am facing EXACTLY the same problem with my 5Dmk3 as well. I am running the Nightly.2015Dec20.5D3123. Has there been any resolution to this?
regards,
Guru
For 5D3, see first post here: http://www.magiclantern.fm/forum/index.php?topic=14704.0
Couldn't see any post related to the specific issue I am facing with Motion Detection and this thread was for the exact same problem, so posted here. Will post my question in 5D3 thread...