Please discuss raw recording issues in the Raw Video (http://www.magiclantern.fm/forum/index.php?board=49.0) section of the forum.Raw recorders (mlv_rec, raw_rec) are just apps that run on top of Magic Lantern core, just like Auto ETTR (http://www.magiclantern.fm/forum/index.php?topic=5200), Arkanoid (http://www.magiclantern.fm/forum/index.php?topic=7847), Dot-Tune (http://www.magiclantern.fm/forum/index.php?topic=4648) and many other modules (http://www.magiclantern.fm/forum/index.php?board=52.0). This thread is for issues specific to the 5D Mark III port (in particular, problems introduced in 1.2.3 that did not exist in 1.1.3).
Any messages about RAW/MLV from this thread will be deleted without notice.
It's out! (http://builds.magiclantern.fm/)
Not alpha, not beta, nor zeta, just a bleeding edge that happens to work for me. It might work for you or it might not.
(note that my standards are fairly high, so what I call bleeding edge, others may call semi-stable or whatever)Installation:1) Format the card from the camera.
2) Make sure you are running Canon firmware
1.2.3 (http://pel.hu/down/eos5d3-v123-win.zip).
3) Copy ML files (http://builds.magiclantern.fm/) on the card and run Firmware Update.
Uninstallation:1) Run Firmware Update from your ML card.
2) Follow the instructions.
What's hot:- bootflag issue solved! (p.s. some bloggers got it wrong, you still enable it in the camera, but you can disable it by uninstalling)
- installation is really easy (simply unzip the files on the card, update firmware and you are ready to go)
- uninstallation is equally easy (update firmware and follow the instructions)
- EosCard is now optional
- ML restores itself after formatting the card (man, that komputerbay card is fast!)
- you may install on any card combination you may think of
- over 300.000 downloads (http://a1ex.magiclantern.fm/download-stats.png) in the last two months :)
What's not:- unlike most firmware updates which fix minor things, this one changed a LOT, especially on the display side (for example, LiveView is now quad-buffered and most of the display registers were changed).
- watch out for corrupted frames (http://www.magiclantern.fm/forum/index.php?topic=10443) (still an issue?)
- fast zebras not working, but can be fixed
- no full-screen magic zoom (I never used it anyway, but was nice)
- no brightness/contrast/saturation adjutments (registers changed)
-
[SOLVED!] HDMI issues- no documentation (yet).
For photo use (raw overlays, ETTR and so on) it should be just fine (that's how I use it).
Source code:- the
5D3-123 branch (https://bitbucket.org/hudson/magic-lantern/branch/5D3-123) in the main repository.
- feel free to merge it locally (http://www.magiclantern.fm/forum/index.php?topic=9524) with unified (https://bitbucket.org/hudson/magic-lantern/commits/branch/unified) or experimental branches (https://bitbucket.org/hudson/magic-lantern/branches) to get a sneak peek for the future updates.
- I'll merge it to unified when I'll be confident it's at least as good as the 1.1.3 branch (based on your feedback).
Thanks to:- chris_overseas for initial porting and testing
- horshack for advice about safely toggling the bootflag
- Audionut for early builds and support in the early porting thread (http://www.magiclantern.fm/forum/index.php?topic=9827)
- marekk, pompeiisneaks, jpaana, rufustfirefly, sinubis and others for early feedback and small fixes
- mk11174 for getting the 700D port in sync in this one
- everyone else who volunteeres their time to make a great community project.
Final notes:-
check nightly builds often and stay up to date! I'll do my best to make sure there are no critical issues in the nightly builds.
- there
are quirks and bugs waiting to be fixed (please report them properly, with details on how to reproduce (http://www.chiark.greenend.org.uk/~sgtatham/bugs.html)).
- grab the ARM toolchain and start hacking! (start with something easy (http://www.magiclantern.fm/forum/index.php?topic=9625) or just tweak/fix whatever you find interesting).
- If anything goes wrong, we don't pay for repairs.
Use Magic Lantern at your own risk!coming soon: a lot of stuff, including a real sensor upgrade, a C compiler that runs on your camera and other geeky stuff like this
Thank you so much for bleeding edge build!!!
Finally a build with simplified installer and uninstaller. Your a legend.
Going to install this tonight and have fun!
I announced it on CR: http://www.canonrumors.com/forum/index.php?topic=20051.0
Thanks to everyone who made it possible!
What will people complain about now that the bootflag is solved? :D
wooooohoooooo...first test seems to be working very good.
you guys are legends .many thankssssssss
thanks a lot, guys.
Many thanks! wohoo :D
Going to test it today
WOW !!! Don't have a 5D but this is spectacular!! Indeed, a living legend, a living machine legend!
Congratulations! Even more people will be drawn to ML now with the bootflag issue solved.
Quote from: KurtAugust on March 16, 2014, 04:30:34 PM
Congratulations! Even more people will be drawn to ML now with the bootflag issue solved.
Indeed we'll see about this, my theory is that some part of people shying away from the missing bootflag removal are too cautious to try ML at all as it's still widely regarded has a "hack".
is it safe now to install ML on a mark iii ?
thanks
Quote from: carlosgaviria on March 16, 2014, 04:51:14 PM
is it safe now to install ML on a mark iii?
It's as safe or unsafe as before, it's apparently just easier and and uninstallation is possible.
You're still running bleeding edge nightly code usually just tested by one single person, though as alex wrote he's very concerned with safety and thus nightly appears to be effectively the new rolling stable-ish release.
Whow, thx you very much..
OMG, THANK YOU! for fixing the bootflag. It was a serious problem for me when it comes to shooting stills.
It works fairly well.
What I noticed so far:
+) when HDMI+LCD mirroring is active, ML acts like it does when Canon displays are ON (so no overlays, neither in camera lcd or in external monitor). Infact, inside ML menu, info bar at the bottom keep saying "Press INFO (outside ML menu) to turn Canon displays off.".
I can tell you that i bout the 5d3 only because of ml raw with 1.2.3.
i waited for that release, refreshing chris overseas topic "how do i dump 5d3 1.2.3" and the bit bucket branch 100 times a day.
evan started to learn coding c# ( i know some vb and java) for trying to help.
I think that yesterday i was the first one who volunteer installing this version.
As i learned by the time A1ex do not release versions before he test it again and again and again.
Lots of people waited for that moment. truly a happy day.
some of us should also learn not asking when, if you want to get "when" closer to now, just try to help by testing, by coding, whatever. and move this project forward.
As stated elsewhere before:
Install with an original Canon battery or a 3rd party battery
that is not requiring you to acknowledge using it,
OR hold your fingers still and wait until the installer finishes
in the background before acknowledging the use of this battery.
ML did not load >:(
Has this to do with the fact that I am using a 64GB SD card?
Please see my post on the CR forum http://www.canonrumors.com/forum/index.php?topic=20051.msg378682#msg378682 (http://www.canonrumors.com/forum/index.php?topic=20051.msg378682#msg378682)
Quote from: a1ex on March 16, 2014, 03:26:45 PM
- watch out for corrupted frames (http://www.magiclantern.fm/forum/index.php?topic=10443) (from my limited testing, I'm not fully convinced the issue is fully resolved on 1.2.3 => for serious video use, please consider staying on 1.1.3)
So, if we're mainly using the Mark III for H264 and RAW video, you recommend to stay on 1.1.3 because of the corrupted frames, or it shoudn't happen? Will it be the same as 1.1.3 or worse?
rpt: try with a smaller card
albertgarciarue: did you get pink frames on 1.1.3 with latest builds? I don't see your voice here: www.magiclantern.fm/forum/index.php?topic=10443
Quote from: a1ex on March 16, 2014, 07:29:52 PM
rpt: try with a smaller card
albertgarciarue: did you get pink frames on 1.1.3 with latest builds? I don't see your voice here: www.magiclantern.fm/forum/index.php?topic=10443
I'll try that tomorrow. Thanks.
after recording number of mlv recording only one was with corrupt frame and it was the first frame.
Do the installation instructions above apply if we are running nightly builds on 1.1.3 and already have the boot flag flipped on? I think Im on a March nightly build on 5d3. With that being said if we uninstall from from the 1.2.3 does that completely remove the boot flag? Sorry if this is a irritating question. I haven't read up on 1.2.3 yet
Quote from: hjfilmspeed on March 16, 2014, 09:25:46 PM
Do the installation instructions above apply if we are running nightly builds on 1.1.3 and already have the boot flag flipped on? I think Im on a March nightly build on 5d3. With that being said if we uninstall from from the 1.2.3 does that completely remove the boot flag? Sorry if this is a irritating question. I haven't read up on 1.2.3 yet
If you have the bootflag already enabled, just upgrade to 1.2.3 Canon firmware, power off the camera, put ML (1.2.3 build) on card, et voilà.
First of all, THANKS A LOT for your work with ML!
I've been waiting for a 1.2.3 release forever!
I installed it but I can't find the M tab for raw video.
The M tab seems to be replaces with a triangle symbol tab.
I fixed it!
Thanks a bunch!
I have been 'playing' with the latest 5DIII version all day in 'photography' mode, ie I don't do video.
All looks good and stable.
The only thing I will say is that, for the old fellas like me, with poor eyesight, it would be nice to see the 'green bar' confirmation in magic focus a little clearer, ie broader bar or maybe a green dot in the magic window.
I fully appreciate this is minor and I will continue to test and report.
Once again: well done ML (and Alex!)
Great!!! Here is the very first test of the Magic Lantern for 5D Mark III 1.2.3 I just installed this new ML version and then I made a couple of shots to test the raw, which WORKS PERFECTLY!
The only issue, I was so in rush trying it that I committed the mistake to shoot with a very low ISO, so I had to increase the exposition in Lightroom, and this is why there is an incredible amount of noise, which indeed it wouldn't be there if I would have shoot at a decent ISO.
I will keep testing the other functions and then come back with updates!
Thanks a lot ML guys!
IMPORTANT UPDATE 17th March 2014: Today I have tested the raw video capability again, this time with clips longer than 30 seconds. I shot two long shots: the first one, the one embedded below, is OK, while the second one is corrupted, meaning I can't convert it with RAWmagic, and I definitely can't use it... this is so bad! I am not sure if I am the only one having this issue, but must be seriously considered if you plan to shoot a job with this.
The video has been shot on:
Canon 5D Mark III
Tamron SP 24-70mm f2.8 USD
CF Lexar Professional 1000x 32GB
Special thanks to EXIV
Music: "Yiourgh" by DoKashiteru (feat. Coblat)
http://ccmixter.org/files/DoKashiteru/21394
is licensed under a Creative Commons license:
http://creativecommons.org/licenses/sampling+/1.0/
Quote from: a1ex on March 16, 2014, 07:29:52 PM
albertgarciarue: did you get pink frames on 1.1.3 with latest builds? I don't see your voice here: www.magiclantern.fm/forum/index.php?topic=10443
No, I didn't although I don't know any about builds or nightly builds as I only have installed ML once and as all I needed was working perfectly I didn't touch it (5D3 mainly using H264 and raw video). So I don't know what build I have installed. I'd like to know more about this but I'm a bit lost.
Thank you for your exellent work. Then I'll be trying 1.2.3 really soon.
There seems to be flickering everytime i use Magic Zoom in the zoom box. My settings are Large, 1:1, Zoom +rec
Thank you a lot for that release! I'll do the update later though because of "for serious video use, please consider staying on 1.1.3"
I can't wait for the sensor upgrage! :-)
Quote from: Jolly Roger on March 16, 2014, 09:53:52 PM
If you have the bootflag already enabled, just upgrade to 1.2.3 Canon firmware, power off the camera, put ML (1.2.3 build) on card, et voilà.
@Jolly Roger Realy? Wow.
No eoscard? Get rid of bootflag? This goes against everything i know about ML ha this is awesome!
Anyone shooting with there record CF card (not ML SD card) formatted to EXFAT on 1.2.3. I like the file spanning of raw_rec when recording to EXFAT CF card
Just tested it on my 5D3! Superb!
I would like to thank you for 1.2.3 + bootflag removal support.
It works wonderfully. I tested it on my new (2nd) 5D3.
Then I verified the shutter count. It was 132 after my playing enough so it was new. You see when I got it I put a card without formatting it. It contained photos. I took some pictures then formatted. I saw numbers starting from 500 and I worried.
I knew it was my mistake the moment I switched cards and the number jumped to 900!
But now I verified it. Yet another plus for ML.
Thanks again...
for higher ISO's try to use Neat Video Denoiser. it does it's job very well on RAW files. Of course in camera raw disable all sharpening and add id after removing all noise.
i'm amazed with the results i've achieved with this software.
how can i enable raw? or is it not showing because my card is not fast enough?? any thoughts?
Quote from: samkolder on March 17, 2014, 04:46:38 AM
how can i enable raw? or is it not showing because my card is not fast enough?? any thoughts?
My thought is you should search this forum a bit.
One thing I have noticed is that the SET option in auto-ETTR doesn't seem to work. The double press is fine.
Unless, of course, I'm missing something. I select SET, go to LV and nothing happens.
Great news!! Thank you so much!
Double checking - I currently use ML 1.1.3 for serious video use as in work for clients. In this case, should I hold off from upgrade from my current firmware "1.1.13-ml-v2.3.NEXT" for now or should I really jump on this firmware 1.2.3 without hesitation? Love to have more input on this..
Like a1ex said couple posts earlier:
Quote from: a1ex on March 16, 2014, 03:26:45 PM
- watch out for corrupted frames (http://www.magiclantern.fm/forum/index.php?topic=10443) (from my limited testing, I'm not fully convinced the seresolved on 1.2.3 => for serious video use, please consider staying on 1.1.3)
I would suggest to be a little patient and wait couple of days.
MZ flicker confirmed on 60fps while recording H264. Was it present on 1.1.3? (I prefer to avoid downgrading back and forth).
ETTR with SET: do you have any custom function assigned to SET? Some of these functions will change the button code.
Quote from: a1ex on March 17, 2014, 07:51:53 AM
MZ flicker confirmed on 60fps while recording H264. Was it present on 1.1.3? (I prefer to avoid downgrading back and forth).
You could also just buy a 2nd 5d2 :-> ... or get hired by Canon at last :-p
Quote from: a1ex on March 17, 2014, 07:51:53 AM
Some of these functions will change the button code.
Wa-what? I never heard about this ... what functions do set the SET (or other) button codes? Thanks.
kgv5: Understood. I'll take the advice and wait a little longer for more feedback. Definitely can't have corrupted frame headaches.
I long for the day when we could do continuous RAW recording without header/footer issues, but I guess that's for another thread.
Quote from: a1ex on March 17, 2014, 07:51:53 AM
MZ flicker confirmed on 60fps while recording H264. Was it present on 1.1.3? (I prefer to avoid downgrading back and forth).
60fps H264? Couldn't this be done anyway? Maybe elaboration is needed.
Quote from: Marsu42 on March 17, 2014, 07:55:29 AM
what functions do set the SET (or other) button codes? Thanks.
SET->ISO for example (just try them all and check).
Excellent work a1ex.
1000 Thanks, very good work !
Quote from: KenshirouX on March 17, 2014, 07:00:14 AM
Double checking - I currently use ML 1.1.3 for serious video use as in work for clients. In this case, should I hold off from upgrade from my current firmware "1.1.13-ml-v2.3.NEXT" for now or should I really jump on this firmware 1.2.3 without hesitation? Love to have more input on this..
This is what I meant. I'll be waiting a few days.
Quote from: KenshirouX on March 17, 2014, 07:57:39 AM
60fps H264? Couldn't this be done anyway? Maybe elaboration is needed.
That's not possible as far as I know.
Quote from: albertgarciarue on March 17, 2014, 09:59:34 AM
That's not possible as far as I know.
I'm confused. The 5DMIII as standard (without ML) can output 60fps H264 on a 720p resolution. Isn't this what is being talked about? I need some clarity to settle my mind on this one.
Quote from: KenshirouX on March 17, 2014, 10:23:13 AM
I'm confused. The 5DMIII as standard (without ML) can output 60fps H264 on a 720p resolution. Isn't this what is being talked about? I need some clarity to settle my mind on this one.
I meant H264 1080p 50 or 60fps, I don't know what he referred to. Sorry about that. H264 720p at 60fps is possible even without ML as you say ;)
Quote from: albertgarciarue on March 17, 2014, 10:58:53 AM
I meant H264 1080p 50 or 60fps, I don't know what he referred to. Sorry about that. H264 720p at 60fps is possible even without ML as you say ;)
Thanks for clearing that up, I understand your need now. I also really want this, ideally, I really want this in RAW format without using any stretching tricks. It would be fantastic if, somehow, the techs can figure this out and somehow pull-off 120fps at 720p. Such a wishlist that probably isn't possible, but hey, what do I know?
What I also want, and probably more useful, is the ability to switch/toggle the Zoom feature on the viewfinder whilst recording so you can perform a focus adjustment with accuracy without the need to buy an additional viewfinder. That would help massively as I have been in quite a few situations where I was, somehow, out of focus and it was really hard to tell in the standard viewfinder. Compared to the FPS wish, I feel the zoom toggle whilst recording would probably be more feasible. Again, my apologies for plugin this wish as that would be in a different thread.
I was trying to use liveview with focus peaking and zebras.
It worked once, but every other time it crashed - gave me an error with I entered liveview mode.
Or in liveview I pressed 'info' to switch views, and it would lock.
Also had missing file message on boot up - about to try again loading from SD.
Here's a zip of logs I took from the card
https://www.dropbox.com/s/21luj8q67wcuslx/5dm3_errors.zip
Does this help? sorry if this isn't the place to do this :)
I tried to install from the SD instead (32gb instead of 64gb cf) - still crashes when trying to get things to work in liveview.
Can you upload your ML/SETTINGS directory and describe the steps to reproduce?
I had Just tested the 1.2.3 on my 5D3 , Thanks for the Excellent work.
The raw rec was good up to 1920x1080x25p (Normal and crop mode) on Koputerbay 64GB.
But the MLV Raw doesnt work for me more than 1 min (4GB) and then it dumps some debug info about QUED something.
a sample of Logfile that was made to the root dir :
ML ASSERT:
hdr->blockSize >= (sizeof(mlv_vidf_hdr_t) + hdr->frameSpace + frame_size)
at mlv_rec.c:1990 (process_frame), task Evf
lv:1 mode:3
Magic Lantern version : Nightly.2014Mar16.5D3123
Mercurial changeset : a9dced4a127b (5D3-123) tip
Built on 2014-03-16 13:26:55 UTC by
[email protected].
Free Memory : 165K + 3742K
Quote from: a1ex on March 17, 2014, 07:51:53 AM
MZ flicker confirmed on 60fps while recording H264. Was it present on 1.1.3? (I prefer to avoid downgrading back and forth).
ETTR with SET: do you have any custom function assigned to SET? Some of these functions will change the button code.
MZ Flicker did not exist in 1.1.3
Quote from: a1ex on March 17, 2014, 11:39:35 AM
Can you upload your ML/SETTINGS directory and describe the steps to reproduce?
Sorry, I had deleted the ML directory - in an effort to get my camera stable again. I only touched the first three options in the menu with global layers, zebra and focus peaking. Also I had visual glitches from the beginning, when in the menus there was something overlapping the bottom section
I have actually found now, after reextracting ML to my CF and leaving the SD card out - it seems to be a lot better. Before I had many visual glitches in the menus. Now it seems to be working consistently.
Could it be related to using two cards? can't get the camera to boot with SD card in at the moment after having deleted the dir.
-- edit I put ML back on the SD, inserted it - still running smoothly. Formatted in the SD in camera (remove ML) - still all working ok
64GB cards are now working for first-time install!!!
(I only had to rename the FIR to 8.3 characters, not less)
I forgot to say :)
Thanks for this!!
I missed it having sold my 5dm2.. I'd be eagerly waiting for it, since I have a MF lens which benefits from it greatly. This software is a joy!
thanks
Quote from: dancook on March 17, 2014, 12:41:57 PM
I forgot to say :)
Thanks for this!!
I missed it having sold my 5dm2.. I'd be eagerly waiting for it, since I have a MF lens which benefits from it greatly. This software is a joy!
thanks
What did you sell your 5Dm2 for?
When using mlv_rec continuous 1080p 25fps, after around 4-5 minutes i get frame skip and then a write out to screen which only goes after i turn off and turn on camera
http://www.flickr.com/photos/35621149@N03/13216327515/
http://www.flickr.com/photos/35621149@N03/13216324395/
Installed and working! Another success!! :-) Amazing...
Nightly.2014Mar16.5D3123 here.
I have 2 questions however...
๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏
1) Installing and booting from a CF card is still not possible? I am currently running ML off an 128GB SDXC card which works great (had to make it bootable with make_bootable.sh for it to work however). I tried to also set up my 128GB 1050x Komputerbay CF in the same way, but with just the CF card in, the camera is completely unbootable and non-responsive until I take out the battery. If both the SDXC and CF cards are inserted, I get the message:
QuoteML on both cards, loading from SD.
and ML loads fine and I can shoot/record to either card. Also, if just the SDXC card is inserted, I can also use ML with no issues. According the the message, ML detects a copy of itself on the CF card, but cannot load from there (and makes the camera seem broken until I pop out the batteries!). Is this normal behaviour? Is it impossible to boot from CF cards?
๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏
2) Audio recording in movie mode, even with H.264, seems to not work at all unless mlv_snd is loaded and enabled. Furthermore, mlv_snd causes many errors unless mlv_rec is also enabled. Therefore, there a couple of things that need fixing. Most important is being able to record normal H.264 video
and audio without having mlv_snd enabled. As far as I understand it, the mlv_snd module is for adding audio recording to MLV-style RAW video recording. This is also what the module description indicates:
QuoteWith this module, mlv_rec is extended by sound recording support.
So why do we need this module enabled to record normal H.264 videos with audio when using ML? In the Canon firmware menus, the audio recording is enabled and volume up, but when starting to record H.264 videos without mlv_snd disabled (default configuration!), it gives an error that audio recording is disabled. This is confusing and seems to be broken. Does normal H.264-mode audio recording really depend on mlv_snd, or is this a bug?
On a related note, enabling mlv_snd but leaving mlv_rec disabled causes many ML errors to the point of disfunctionality. This is a user interface issue, really. If one module depends on another to function, then the UI must load not only the user-selected modules, but its dependencies as well.
As it stands, after a default install, audio recording seems broken unless *BOTH* mlv_snd and mlv_rec are enabled. So if you want normal H.264 video recording with audio, you need to enable RAW video recording modules but disable the RAW video recording. This is not only counterintuitive, but it gives users a default broken configuration for normal (non-RAW) video recording.
๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏๏
If anyone else can confirm any of the issues I have outlined, it would be appreciated!
1) already answered
2) H.264 sound works out of the box, no modules needed
ETTR with SET: do you have any custom function assigned to SET? Some of these functions will change the button code.
Alex as soon as you said this I realized the problem. SET custom function cleared and all working now.
Quote from: a1ex on March 17, 2014, 01:15:46 PM
2) H.264 sound works out of the box, no modules needed
I can also vouch for this. Sound always worked out of the box even before ML.
Quote from: gideonplus on March 17, 2014, 11:40:54 AM
I had Just tested the 1.2.3 on my 5D3 , Thanks for the Excellent work.
The raw rec was good up to 1920x1080x25p (Normal and crop mode) on Koputerbay 64GB.
But the MLV Raw doesnt work for me more than 1 min (4GB) and then it dumps some debug info about QUED something.
a sample of Logfile that was made to the root dir :
ML ASSERT:
hdr->blockSize >= (sizeof(mlv_vidf_hdr_t) + hdr->frameSpace + frame_size)
at mlv_rec.c:1990 (process_frame), task Evf
lv:1 mode:3
I have almost same issue as yours. At 24p 1920X1080, Transcend 1000x 64GB CF.
MLV mode with Files->GiB (exFAT)
enabled: I can only record for ~11XX frames. ~4.0XXGB file size (~50 sec.)(read from "Status when recording->Debug). then recording stop. no bug info screen.
MLV mode, Files->GiB (exFAT)
disabled. I can record for 23xx frames. ~8.1XXGB (~100 sec). then bug info screen pop, but it still recording. During recording, there will be a brief pause (~0.5sec.) at 11XX frames (~4GB file size), then keep going.
It looks like there is a 4 GB barrier.RAW_REC mode, no problem for 5 min. recording test. never try longer, no need.
For MLV, please report issues in the MLV thread: http://www.magiclantern.fm/forum/index.php?topic=7122
It's still a work in progress, and so far the issues reported were not 5D3-123-specific, but MLV-specific.
Quote from: a1ex on March 17, 2014, 02:43:39 PM
For MLV, please report issues in the MLV thread: http://www.magiclantern.fm/forum/index.php?topic=7122
It's still a work in progress, and so far the issues reported were not 5D3-123-specific, but MLV-specific.
A1ex, do you have an idea how feasible would be to allow the magic zoom feature to be toggled on and off during RAW recording to optimise focusing? I'd love to have this feature as I believe it's more reliable than the Zebra option. Your thoughts?
Quote from: KenshirouX on March 17, 2014, 12:44:28 PM
What did you sell your 5Dm2 for?
To upgrade! more iso, silent shutter, better AF - mk3!
MAGIC , Updated firmware 113-123 , installed ML tested Bootflag on/off (works perfectly) Recorded three 2 minute MLV with audio , got split files , then put Files to 4gig Exfat ON and Recorded Again no probs , this version MLV in 123 seems the most stable one ive used so far , also tested RAW and H.264 all working as expected.
Thanks ML
Jafa.
Quote from: a1ex on March 16, 2014, 07:29:52 PM
rpt: try with a smaller card
albertgarciarue: did you get pink frames on 1.1.3 with latest builds? I don't see your voice here: www.magiclantern.fm/forum/index.php?topic=10443
So it loaded. I used a 4GB card and it loaded without a problem. The uninstall worked fine too :)
Now to locate the documentation and start reading it :)
Thanks!
I just had a slight problem that I solved, hope this helps someone else.
At first after following instructions, I thought my two 5D3 were bricked...
But then I realized you have to install the LATEST or nightly build which includes the *.FIR file in it.
Then it boots, loads automatically, and goes from there.
THANK YOU GUYS!!
@rpt: can you install the latest nightly on the 64GB card?
(it worked on mine, with exfat)
64 GB worked fine for me....
I was already running ML 1.2.3 on my 5D3 that I'd compiled from Chris's repo. Followed A1ex's instructions and now I'm running wonderfully here. Tested disabling and reenabling the Bootflag. Also no glitches. Congrats to Chris_overseas, A1ex and every other contributor for this!
Quote from: a1ex on March 17, 2014, 01:15:46 PM
1) already answered
I had already lookd through this entire thread as well as did an forum search for the entire site to find the technical reason why CF cards are non-functional for booting ML even if made bootable via normal methods (EOSCard.exe or make_bootable.sh). Seeing as you know that it was discussed elsewhere, it may be best not to spend more time in the 1.2.3-specific thread asking about it, but it is still not clear why booting from CF is not technically possible at this time. Any links to further information would be appreciated.
Quote from: a1ex on March 17, 2014, 01:15:46 PM
2) H.264 sound works out of the box, no modules needed
The audio was broken on the March 16th nightly, but I just upgraded to the March 17th and now I can record audio on H.264 mode as well. The March 16th build was flashing a "Audio recording disabled" error as soon as I hit the Start/Stop button to begin recording and it never showed the audio recording meters in Canon firmware mode or in the ML live view with the larger ML audio bars up top. Only the menus in the Canon firmware would show mic activity unless mlv_rec and mlv_snd were enabled.
March 17th build fixes the audio recording being disabled for me.
1)
Quote from: a1ex on March 17, 2014, 11:59:33 AM
64GB cards are now working for first-time install!!!
(I only had to rename the FIR to 8.3 characters, not less)
2) I bet you have enabled FPS override.
This is fantastic news! Thanks to chris_overseas, A1ex, and everyone else who helped make this happen!
Yeah thanks chris & a1ex !!
After a long follow on bitbucket it's here now !! :)
Great thanks a lot!
Like on bitbucket issues, canon overlay on lv (https://bitbucket.org/hudson/magic-lantern/issue/1900/mls-lv-got-overlay-by-canons) it's always present and dualiso module doesn't change the custom prefix (https://bitbucket.org/hudson/magic-lantern/issue/1892/dual-iso-custom-file-prefix-problem) of the file.
I'll investigate to solve these issues :)
Quote from: EXIV on March 16, 2014, 10:36:34 PM
while the second one is corrupted, meaning I can't convert it with RAWmagic, and I definitely can't use it...
what kind of corruption?
Quote from: a1ex on March 16, 2014, 03:26:45 PM
Uninstallation:
1) Run Firmware Update from your ML card.
2) Follow the instructions.
What's hot:
- bootflag issue solved! (p.s. some bloggers got it wrong, you still enable it in the camera, but you can disable it by uninstalling)
Silly question (maybe?) - I run 1.1.3 and toggle between 1.2.3 prior to this release - no problems. If I wanted to completely remove the bootflag from my camera can I just install and then uninstall this version? Then go back to Canon's OEM firmware and there's absolutely no remnants of ML anywhere? (This is in case I need to send the camera in for repair or decide to sell it).
Thanks!
Shawn
Another silly question; I installed this version from a 16gb sd card to try it out. I tried the uninstall instructions but it just seems to go through the install procedure again...
It does give me 30s to remove the boot flag. Do I need to let this run for it to uninstall correctly?
Quote from: engstrom on March 17, 2014, 11:28:34 PM
Another silly question; I installed this version from a 16gb sd card to try it out. I tried the uninstall instructions but it just seems to go through the install procedure again...
It does give me 30s to remove the boot flag. Do I need to let this run for it to uninstall correctly?
Yes, wait patiently ... 30 seconds :)
Quote from: ImaXineria on March 17, 2014, 09:55:36 PM
what kind of corruption?
It is simply impossible to extract the dng files from it. I have tried with RAWMagic and raw2dng but both give me error:
Thanks so much! I can now finally use my eye fi cards with my mark iii. You guys are awesome!
hi
much appreciate on 1.2.3 alex
i wish you can have modules like sound on the *.raw format
mlv is difficult to process
I am using raw2dng to process, it is very easy to use, i am using komputerbay 1066x, it is fast enough
i tried to use mlv, it has error saying state 4 something
QuoteIt is simply impossible to extract the dng files from it. I have tried with RAWMagic and raw2dng but both give me error
May be you fill the card with the second shot (the one corrupted)?
Good job ML!!!!! Yupieeeeeeeeeeee
Also announced on timelapse.pt facebook page
www.facebook.com/timelapsept
Good job!
Quote from: a1ex on March 17, 2014, 08:19:08 PM
1)64GB cards are now working for first-time install!!!
(I only had to rename the FIR to 8.3 characters, not less)
Ah, I see why you think it has already answered. I did notice that my exFAT cards were not working with the March 16th nightly before the .FIR 8.3 filename fix, so I did the initial install with a 32GB SDHC card and thereafter made my SDXC cards bootable manually. Since the 8.3 firmware fix, I can take a brand new, unmodified exFAT-formatted SDXC card and put the fixed nightly data onto it, and the .FIR-flashing process makes the card bootable and works great. I am happy to report that I have tested it multiple times on 4 separate SDXC cards at 128GB capacity, all exFAT. ML for 1.2.3 runs great from these cards with the new .FIR file to set it up, and it was also running when I made the cards bootable manually via make_bootable.sh/EOSCard.exe after initial installation on-camera with a 32GB SDHC card.
My problem however is with my Komputerbay 1050x CF card. I cannot get ML to load from this card. If I try to make it bootable on my computer *OR* if I try to make it bootable using the .FIR update method (yes, even with the 8.3 filename fix), it creates a completely unusable card. Whereas it starts as a perfectly mountable/usable exFAT filesystem, after trying to make it bootable via
either method, the camera cannot recgonise it and asks to format it. The laptop fails to mount the partition on the CF card when in the card reader, complaining:
ERROR: invalid VBR checksum 0x258ed093 (expected 0x30c2a1c9).
Furthermore, fdisk reports the filesystem to be type "W95 FAT32 (LBA)" after making it bootable. Before, fdisk correctly read the partition table and detected the filesystem as type exFAT. I have more SDXC cards around that I can always boot ML from, so I do not strictly
need ML bootability from the CF card, but I want to know if there is something wrong with my CF card itself or the ML install process.
Quote from: a1ex on March 17, 2014, 08:19:08 PM
2) I bet you have enabled FPS override.
Oops! You are correct. Sorry about that. I changed to 1080p/24fps in the Canon firmware menu and disabled FPS override. Obviously audio recording is working again! I just wanted to do my RAW testing with 25 fps + audio, but I guess that's not possible atm... ???
Quote from: alMalsamo on March 18, 2014, 02:11:04 PM
My problem however is with my Komputerbay 1050x CF card.
Anyone else tried this card?
If all Komputerbay 1050x 128GB cards have this problem, I'll probably have to get one and see what exactly is going on. If it's only your card... it may be a bad card.
Since other 128GB cards are working fine... I'm not sure where to look.
Quote from: alMalsamo on March 18, 2014, 02:11:04 PM
My problem however is with my Komputerbay 1050x CF card. I cannot get ML to load from this card. If I try to make it bootable on my computer *OR* if I try to make it bootable using the .FIR update method (yes, even with the 8.3 filename fix), it creates a completely unusable card.
I have a 128GB KomputerBay 1050x CF card formatted as FAT32 and I just tested it, ML boots from it just fine. I haven't tried it as exFAT yet but I presume that will work too. I think I know what your problem is though... how old is your card? The early 1050x cards had a problem that prevented them from booting. Here's the relevant post from KomputerBay support explaining the situation: http://www.magiclantern.fm/forum/index.php?topic=8857.msg83814#msg83814 I emailed KomputerBay in mid-November (a month after that post) and they said that even then Amazon still had some of the old (ie non-booting) cards in stock. As a result I bought mine direct from KomputerBay instead to be sure I was getting a bootable one.
As an aside: why do you want ML on your CF card anyway? I prefer to have it on an SD card that's dedicated to ML. That way I can change & format CF cards at will without worrying about my ML current settings getting lost or whatever. Mind you now that a1ex has added support for retaining ML across a format it isn't quite such a big issue as it once was.
Quote from: a1ex on March 18, 2014, 03:01:09 PM
Anyone else tried this card?
If all Komputerbay 1050x 128GB cards have this problem, I'll probably have to get one and see what exactly is going on. If it's only your card... it may be a bad card.
Since other 128GB cards are working fine... I'm not sure where to look.
I had this card and had to send it back. i couldn't get FULL HD RAW or further, it had a write speed of about 70 MB/s. is there any card that always works? maybe komputerbay 64GB 1000x??
Does this somehow allow me to record RAW footage via the HDMI to an external recorder or is that just wishful thinking?
i am using komputerbay 128gb 1066x, when i got it in the first time, it was dead, i had to return it, then i rebought it, it is fine until now. very fast card
Just wanted to drop by and say thank you.
I Have been watching and awaiting a 1.2.3 release for some time so I could try ML on my 5DM3.
Its here... its installed, and it worked first time. Excited to get out and play with it.
I prepared a short video from photo workshops with mlv_rec on 1.2.3 ... no problems and no bad frames at all :)
My video:
http://www.magiclantern.fm/forum/index.php?topic=11031.0
Can anyone tell me which file I need to install for 5d mrk iii 1.2.3. From magic lantern??? Thanx buddies....
Quote from: pc_bel on March 18, 2014, 09:37:44 AM
May be you fill the card with the second shot (the one corrupted)?
Impossible... there was still plenty of space as the card I used was a 32GB Lexar 1000x and both the two clip I shot were about 4.5GB each...
Quote from: gandhre1011 on March 18, 2014, 06:42:23 PM
Can anyone tell me which file I need to install for 5d mrk iii 1.2.3. From magic lantern??? Thanx buddies....
Top of page -> Downloads -> Browse Nightly Builds -> Choose your flavour ...
Quote from: Walter Schulz on March 18, 2014, 06:51:19 PM
Top of page -> Downloads -> Browse Nightly Builds -> Choose your flavour ...
thnx a lot brother.....
Here is my third test on this new ML version. This time I have decided to make a straightforward comparison between the H264 video coming from the camera and the Magic Lantern RAW. I have edited the footage without grading it, so to make it easier to compare the quality between the H264 and RAW.
Wow, h264 holds up really well Exiv. This isn't the drastic difference as I see in other video's.
Quote from: gandhre1011 on March 18, 2014, 06:53:40 PM
thnx a lot brother.....
can I just install 5d3 123 bleeding edge??
Do you have more options?
I hve already install magic lantern for 1.2.3 but I did not get raw option for movie shoot... can anyone tell me??? Thnak you
You might want to take some time for reading FAQ, manuals and other messages in ML forums.
Access "Module" tab and load options as needed. Afterwards (and after restart) you are able to access those options.
Quote from: Walter Schulz on March 18, 2014, 07:32:04 PM
You might want to take some time for reading FAQ, manuals and other messages in ML forums.
Access "Module" tab and load options as needed. Afterwards (and after restart) you are able to access those options.
yea I read those... see d issue
Some issues/things not working with HDMI on this release (Tested with Zacuto EVF):
1. Start up with HDMI connected with manual lens lifts mirror but get stuck on manual lens warning message. If you just press canon menu button and step in and out of that menu you get rid of the message and camera displays live view with ml info.
2. Misalignment info bars are misaligned/too small check pictures: (The outer frame is generated by zacuto evf and markes the 16:9 recording area.)
This is with 3:2 setting
Was not able to make a internal screenshot of this misalignment with this version. However when i tried an earlier version of ML for 123 i got this misaligned screenshot. They seem to differ slightly and I'm not sure if the setting was 3:2 there as well...
Also had problems recording MLV passed 4gig on xfat card as other people reported. Is the larger than 4gig setting working correctly on this build? Seems suspicious that it stops there...
Quote from: gandhre1011 on March 18, 2014, 07:46:04 PM
yea I read those
<sigh> Turn "RAW video" ON, then press Q.
nice work
Wrong. You won't see this screen at all if RAW_rec.mo isn't loaded.
Thank you very much!
While recoding it says..... bugz... n report.... angry....
You might want to surprise me and fill out a proper bug report. "Doesn't work" won't do.
Ok, it has been a few days since the release of this update. Is it worth updating to 1.2.3 from 1.1.3.NEXT.ML? Anything that I should be careful about if I do update? Is continuous RAW recording working?
Quote from: KenshirouX on March 19, 2014, 11:53:20 AM
Ok, it has been a few days since the release of this update. Is it worth updating to 1.2.3 from 1.1.3.NEXT.ML? Anything that I should be careful about if I do update? Is continuous RAW recording working?
I did two full 64 lexar 1000x cards with MK III and got no problem at all with
raw_rec. Extracted with rawmagic, used a AF lens (so can't tell about the MF bug up there) and finished on resolve. I could say it's pretty stable, but do not forget to make tests by yourself to see if it works on you setup.
4+ GB's archives on ExFat is working fine too. I saw there were something with mlv_rec, but raw_rec is fine here. Didn't tested with mlv, gonna do it today.
What I could say is: When in mirror mode and external monitor ON, the ML display go OFF. It would be nice to have it on LCD and triggered in some way to get on external monitor, like half way shutter or some other way.
But hey, the fact i can now shoot raw with LCD + monitor is just awesome and I know things are gonna keep getting better.
Tell me if there's anything i could do to help you with this new build. I don't know if I'm ready to get back on coding, but I'm getting tempted to and want to help out.
Thanks again!
TREAD CAREFULLY
Don't Know about anyone else but I had a horrible experience with this. As soon as I installed i got big greenish banding rolling through my images and a lot of solarisation. Uninstall alone didn't help. I had to Re-install 1.2.3 from Canons site and thank christ it worked because i was freaking out.
If anyone has had this or knows of something i may have done wrong to cause it then i'm all ears.
J
Quote from: jCurve on March 20, 2014, 03:30:03 AM
TREAD CAREFULLY
Don't Know about anyone else but I had a horrible experience with this. As soon as I installed i got big greenish banding rolling through my images and a lot of solarisation. Uninstall alone didn't help. I had to Re-install 1.2.3 from Canons site and thank christ it worked because i was freaking out.
If anyone has had this or knows of something i may have done wrong to cause it then i'm all ears.
J
so which nightly build did you use? Provide informative details so the devs can troubleshoot bugs.
There is a reason why its called "bleeding edge" because it offers new features and it comes with risks when you are willing to test these builds.
Quote from: ted ramasola on March 20, 2014, 04:06:19 AM
so which nightly build did you use? Provide informative details so the devs can troubleshoot bugs.
There is a reason why its called "bleeding edge" because it offers new features and it comes with risks when you are willing to test these builds.
Yep, right you are. the build was the latest provided from the link at the top of this thread: Latest Build
Built on: 2014-03-17 20:56:54 +1000
Changeset: 48e7ddebc1b9
installed as instructed:
Format card in Camera
Copy files to Card
re insert card to camera and update firmware: Restart Camera.
Here is a quick video of the ensuing result excuse the riveting content:
1.if you shoot outdoors or under a different light source is that banding still there?
2.if you change your shutter speed between 48/50 to 60 or another is that still there and does the banding behavior change when you change the speed?
3.if you do an in-camera preview of your footage is this banding present?
4. is this raw or h264?
this looks similar to an out of sync issue when shooting under florescent light when your voltage is 220 60cycles and your using 48 or 50 shutter.
Quote from: ted ramasola on March 20, 2014, 05:11:36 AM
this looks similar to an out of sync issue when shooting under florescent light when your voltage is 220 60cycles and your using 48 or 50 shutter.
That was my first thought as the banding is rolling. it's similar to the phasing issue you often get with refresh rates on screens etc or as you say different cycles. takes me back to my film days
The footage is h.264 and i did try varying the shutter speed to no avail.
Banding was still there under a different light source.
To be honest i didn't spend too much time pushing the tests because i didn't know whether it was a sensor issue and none of the usual tests were resolving it. Not to mention when i was bracketing exposure during some tests the images were completely solarised when the lens was wide open so.... um yeah.
I've only just started venturing into the DSLR side of things due to client demand. usually i shoot with Arri Alexa's, Reds or Sony F5's/55's so i'm open to any advice on optimal use of these cameras.
I'm thinking about giving the install another go but obviously cautious.
Only other things i can think of that may have messed up the install was the use of a micro SD in an adaptor but that really shouldn't hurt or maybe i put the wrong files on the card. I put all the files in the nightly build folder on the card. The Autoexec.bin, the ML folder and the .fir file. To be clear i put the files in the 'Magiclantern-Nightly' folder on the card not the 'Magiclantern-Nightly' folder containing the files.
Any Red flags there.
It really looks like some kind of phasing issue to me which means hopefully the sensor is safe to do some more extensive testing with but who knows...
Took a gamble. did a re-install and it worked :) don't know what that was all about but all seems good now.
J
It's normal, you have been bitten by the laws of physics (http://worldofweirdthings.com/2009/07/01/if-you-break-the-laws-of-physics/) (shutter speed or FPS out of sync with artificial lighting).
a1ex, gave us a little more medicine, and expand this phrase: "coming soon: a lot of stuff, including a real sensor upgrade"
8)
a1ex, please don't! Release date 1. April, please, just for fun!
Should we post testing feedback in this thread or in the original 1.2.3 thread or in the nightly thread frfrom now on?
Quote from: Walter Schulz on March 20, 2014, 08:56:55 AM
a1ex, please don't! Release date 1. April, please, just for fun!
;D
Quote from: eyeland on March 20, 2014, 09:14:08 AM
Should we post testing feedback in this thread or in the original 1.2.3 thread or in the nightly thread frfrom now on?
This thread please.
Walter, so mean! :D
Great Work, Congrats to the ML team! The world is a better place with them in it.
When do you think we will be able to have a stable version of the 5D III ML 1.2.3?
Quote from: davidcovo on March 20, 2014, 10:11:24 PM
When do you think we will be able to have a stable version of the 5D III ML 1.2.3?
Trust me.. this is a question you do not want to ask around here... ;D
Just keep track of the threads as these are work in progress, especially the new port like this. OR you can do your part and give feedback and bug reports with your own testing.
Quote from: budafilms on March 20, 2014, 08:46:20 AM
a1ex, gave us a little more medicine, and expand this phrase: "coming soon: a lot of stuff, including a real sensor upgrade"
8)
Huh? Did I miss something? Will there be another major update within 2 weeks? Should I really wait for that instead of updating to last Monday's update? Don't rattle my chains with mystic codes, my friend.
Teasers are called that for a reason.
You can read about release dates in FAQ, last question.
"coming soon: a lot of stuff, including a real sensor upgrade"
:o
a) I did lot of shots using .RAW
b) The problem start when I put OFF RAW - restart - and Use .mov for a long interview.
c) I put .RAW again, restart.
d) After that shot, the colours of videos appear divide for yellow, green, like a Warhol paint, with out TOO MUCH details.
RESTART. Skipping frames. Restart, Memory Hack On. Global Draw Off. And REC in that conditions.
If you want some file or log, tell me where I can find it you in my card and I send you.
For video lovers:
This is the final video, 1.2.3 with out kaos shoots. Interview in H264. Enjoy
https://vimeo.com/89693948
Quote from: budafilms on March 21, 2014, 06:08:37 PM
a) I did lot of shots using .RAW
b) The problem start when I put OFF RAW - restart - and Use .mov for a long interview.
c) I put .RAW again, restart.
d) After that shot, the colours of videos appear divide for yellow, green, like a Warhol paint, with out TOO MUCH details.
RESTART. Skipping frames. Restart, Memory Hack On. Global Draw Off. And REC in that conditions.
so the problem appears with the RAW files (the 2nd time after switching from h.264 to RAW again)?
have you gone through your steps again and had same result?
what does the frame looks like ? (upload a pic if you can plz)
Wanted to chime in and say Thanks to everyone on the ML team who contributed to the port. I have successfully loaded this on to my 5DM3, and am reaping the full benefits of focus peaking on manual lenses for video :-)
Sasha
ML v123 working great. Installation - piece of cake, THANKS A LOT!
x3 (2560x1072) is up to 60sec (more then enough for one shoot), comparing to v113 - about 30sec at most.
I'm not sure if it is bug or not. I think everyone has it:
when in x3 mode, second frame is pink (no image) and the tenth frame is a couple stops overexposed (in v113 the seventh frame was overexposed in x3). Thus ten frames in 2560x1072 are not usable. As for the rest - v123 is much more stable then v113 TO ME.
Great stuff. Feels like there is no limits there for ML team.
Help help! I recorded both mlv and raw with my 5D3 on Lexar 1000x and Sandisk 1066x but the video ariel all black and won't open. They look fine on the mlv player on the camera though. Using mlv viewer to open the videos on my windows PC. ::)
I recorded some footage ALL-I format and the clips playback just fine on the camera but when i bring them into the computer there errors.
Any help would be greatly appreciated. I can play all the clips perfectly in the camera its pixelated across the bottom.
Quote from: Sergey Pylypenko on March 22, 2014, 01:23:22 AM
ML v123 working great. Installation - piece of cake, THANKS A LOT!
x3 (2560x1072) is up to 60sec (more then enough for one shoot), comparing to v113 - about 30sec at most.
I'm not sure if it is bug or not. I think everyone has it:
when in x3 mode, second frame is pink (no image) and the tenth frame is a couple stops overexposed (in v113 the seventh frame was overexposed in x3). Thus ten frames in 2560x1072 are not usable. As for the rest - v123 is much more stable then v113 TO ME.
Great stuff. Feels like there is no limits there for ML team.
Could I ask what settings you are using to record 5x zoom 2560x1072 , ie-aspect ratio , fps , fps override ? and what type of card and its specs as the best I can get so far on my Komuterbay 64gb 1000x at 5xzoom is 2240x938 continuous record at 25 fps in plain old raw.
Quote from: Canon eos m on March 22, 2014, 01:31:48 AM
Help help! I recorded both mlv and raw with my 5D3 on Lexar 1000x and Sandisk 1066x but the video ariel all black and won't open. They look fine on the mlv player on the camera though. Using mlv viewer to open the videos on my windows PC. ::)
Edit: Figured it out. For some reason MLV convertor / MLV viewer were not able to read files straight from the CF card. Brought the files on the HDD and am now back sailing :-)
Can I ask a stupid question? Why no more nightly builds after March 17?
It's smart. There have been no changes in that branch so it won't build anything
Hello,
Yesterday I went out and did some test. To be honest, it was a terrible day (windy and cloudy) I didn't have any luck getting the shots that I was looking for to share. Nevertheless, whilst post processing my shabby shots, I came across a few takes that were green/black and the rest were fine.
http://s27.postimg.org/fhtkkobxv/green_vid.jpg
I shot with,
5D Mark Free
Canon 100mm F2.8L Macro
Komputerbay 64 1000x
Magic Lantern settings: MLV Raw record, sound enabled, 1920 x 1038 (1.85.1) aspect ratio, all the hacks on.
Ps - I also noticed an increased in digital noise when filming indoor, this could be because my scene was not lit properly as I was just using my light bulb.
I am not worried or panicking, I am just reporting a bug. However, I would like to know if I got some settings wrong.
regards
Okello
have a look at this
http://www.magiclantern.fm/forum/index.php?topic=7122.msg107474#msg107474
Thank you frenchps49
Hi,
I'm new to this board, although I read it quite a while. I hope I don't do anything wrong here.
I have a 5d Mark III with 1.2.3 installed and wanted to give some feedback.
Nightly 2014 Mar 17
+/- Tab ExpSim toggle on/off is shown but can not be selected
+/- Tab pressing SET instead of Q to enter values activates LifeView with ML Menues printed on top (you can still scroll), another SET and you are back.
colors differ slightliy between raw_rec and mlv_rec using mlvmystic (might be mlvmystic?)
"Auto power off" is often set to 2 minutes again after reboot.
But anyway, a great job!
Regards,
kontrakatze
Thank you to everyone who puts all of the work on this! I was one of the ones who waited for the bootflag issue to be resolved before moving passed Alpha 3.
I used the build from 3/17/14 last night at a concert. I didn't get to try much video and only used liveview for a few minutes tops. I noticed the battery seems to drain much faster now than with the Alpha 3 build even though I was not using ML features most of the time.
I'm not sure if this is to be expected but I thought I would post it up. I'll be working with video tonight at a show so I'll get to test much better.
Quote from: Okello on March 22, 2014, 01:40:50 PM
Yesterday I went out and did some test. To be honest, it was a terrible day (windy and cloudy) I didn't have any luck getting the shots that I was looking for to share. Nevertheless, whilst post processing my shabby shots, I came across a few takes that were green/black and the rest were fine.
Also getting some clips with dark green/black images with march 17 build but most ok.. big bug in there somewhere :-X :0
Quote from: pv25pv on March 21, 2014, 06:31:42 PM
so the problem appears with the RAW files (the 2nd time after switching from h.264 to RAW again)?
have you gone through your steps again and had same result?
what does the frame looks like ? (upload a pic if you can plz)
Yes, I repeat the process and ML loose something in the color balance when you shoot H264 and return to shoot .RAW
And start to skip frames.
You have to take off the battery and start again.
The problem is you can't see if every shoot are fine.
this is an example
https://www.dropbox.com/s/j1s7bkhonqh8v1h/fotogramachoto.tiff
Quote from: jafa on March 22, 2014, 10:38:38 AM
Could I ask what settings you are using to record 5x zoom 2560x1072 , ie-aspect ratio , fps , fps override ? and what type of card and its specs as the best I can get so far on my Komuterbay 64gb 1000x at 5xzoom is 2240x938 continuous record at 25 fps in plain old raw.
Sure, all extra Canon settings are OFF, as advised by ML 'best settings for raw recording'.
Highlights are ON, Global Draw all ON, Preview Hacked, Memory Hacks ON, Ratio - 2.39:1, 2560x1072, 24.000fps - maximum that I am able to film practically. Bigger then that resolutions gives just a few secs, which is not suitable for me. 2240x938 goes smooth continuously, but 2560x1072 gives more coverage on sensor with 45-60 seconds of filming, depends on sensor temperature, which is more then enough for normal shooting. I use TRANSCEND 1000x, 128GB.
Thanks for that Sergey , ill give those settings a try later and see if I can eek that little bit more out of mine.
Cheers
jafa
Hi,
on my 5d Mark III with 1.2.3 installed and Nightly 2014 Mar 17:
- Powersave in liveview can't be enabled or disabled (always grayed out), submenues work, Battery Level is only informational, but selectable
Maybe this can be made somehow more obvious (a hint at the bottom in green?):
- Preview mode ML Grayscale in mlv_rec works only if global draw is set to allow (of course)
Best results recording raw I seem to achieve with:
Global draw OFF
Memory hack OFF
Extra Hacks ON
Buffer fill method 3
CF-only buffers 0
Card spanning ON
This appears to be the highest working resolution for my camera: 1792x1008 16:9 @29.97 fps continuouisly without any bad frames (CF 128GB Lexar 1066x and 128GB SanDisk Extreme 45MB/s).
Others seem to get full 1080p @ 30fps continuously, but I absolutely have no clue how they get there...
Regards,
kontrakatze
Quote from: kontrakatze on March 23, 2014, 09:19:50 AM
This appears to be the highest working resolution for my camera: 1792x1008 16:9 @29.97 fps continuouisly without any bad frames (CF 128GB Lexar 1066x and 128GB SanDisk Extreme 45MB/s).
16GB & 32GB cards seem to be faster than 128GB cards.... you may want to search around for some of the threads on different brand cards and speeds if full HD is important to you.
True, but I can't change cards every couple of minutes. That's why I choose the 128GB 1066x. In photo mode it reaches about 115MB/s solid, therefore I think a faster card would not change anything. Read speed is about 158 MB, which is about the max of UDMA7 as far as I know.
Maybe it is he cpu which is to heavily utilized in video mode, so there are to less cycles left for writing?
Regards,
kontrakatze
Then I guess you're stuck with 1792x1008 as a max resolution....
My Transcend 16/32/64 do full HD plus.
they do this at 30fps? So you get a write speed of 106MB/s in video mode?
With or without spanning?
Could you please tell me your settings regarding buffers, hacks and so on?
Regards,
kontrakatze
to se how good is your CF card simply make a test in ML menu...
my kpb 64mb have avg speed about 92mbps
WHAT IS IMMPORTANT is -----> Write speed (Buffer= 16384 K) if you look my picture.
https://www.dropbox.com/s/lp0w5qvn0pfmxp2/VRAM4.BMP (https://www.dropbox.com/s/lp0w5qvn0pfmxp2/VRAM4.BMP)
in my picture you will see the Write speed is (Buffer= 16384 K)---> 94.6MB/s
so that is the speed of card - the tasks what your 5d3 needs to run to make movie and what data rate can get out for raw recording.
magiclantern-Nightly.2014Mar17.5D3123 running on Sandisk xtreme UHS 16GB - CF: Komputerbay x1000 64GB exfat quick format
(i) First 50GB of shooting, monitoring on nexus 7 (DSLRcontroller) worked flawlessly, then started crashing alot. (on 1.1.3 it usually crashes alot from the beginning)
(ii) This build seems to have had an effect on my setup in terms of writing speeds. I can barely get 1920x1080@25fps continuous with all hacks off and GD on.
Low level format and full ML reset does not seem to have an effect of any of the issues I am experiencing. Having some odd numbers in my benchmarks (not sure if posting these has any relevance) - will do some more comprehensive testing later.
So far, I have observed that there is a big difference in bench speeds between 1080/25 and 720/50 (in canon menu) all other things being equal. (720~65mb/s - 1080~85mb/s) (this might be expected behavior, but I only did a bench in 720 recently)
(iii) Getting some Err 70 and Err 80 once in a while that require battery pull - have not been able to determine the conditions but they are much more frequent than they ever were on 1.1.3
Having a hard time determining a good testing methodology. Would it make sense if we compile a standard list of testing parameters? This could improve both testing and the posting of results.
(Edited out some tired nonsense :))
Hi,
today I did some more comprehensive testing with my 5d mark III.
I benchmarked both my lexar cards, a 32gb 1000x and a 128gb 1066x on the latest nightly build for the canon firmware 1.2.3 and 1.1.3
I think the idea "eyeland" had, to compile a standard test setup is quite nice and convincing.
Therefore I took some time to think about it and came up with this setup I used:
Canon
Safety Shift OFF
Tone Priority OFF
Auto Power off OFF
HDR OFF
1920x1080 @ 30fps All-I
Magic Lantern
Global Draw OFF
FPS override OFF
LV DIGIC peaking OFF
Card settings Preferred card CF, others OFF
Modules: mlv_rec, mlv_play, nothing else
almost everything else is set to OFF
Benchmark in movie mode (live view on)
Camera was not moved during the benchmarks and the lighting was constant. I don't know if this is relevant, but it might be as the liveview is on during the benchmark and therefore the cpu has things to do.
I did all benchmarks three times, but got always the same results:
Firmware 1.1.3
Lexar 32gb 1000x w 91.7 90.6 91.9 @16384k
r 122.3 122.3 122.1
Lexar 128gb 1066x w 91.9 93.4 93.3 @16384k
r 122.3 122.4 122.2
Firmware 1.2.3
Lexar 32gb 1000x w 86.3 89.3 89.6 @16384k
r 118.2 118.2 118.5
Lexar 128gb 1066x w 85.4 89.1 89.0 @16384k
r 118.3 118.2 118.4
Next I did a brief test on the power consumption and the heat up of the camera, but these test were not really scientific as I took different batteries, relied on the display (temp) used a plain simple stopwatch and had to press a button every now and than to hinder the camera to shut the display down. Therefore take the result with care.
Anyway, the powerconsumption on 1.2.3 was much higher, the heat raised significantly faster.
By now, the datarate is significantly lower, the power consumption higher and the heat (37°C compared to 45°C after 3 minutes) also.
But hey, I stay with 1.2.3 :D I'm sure this can be sorted out.
Tell me what you think about the setup and let us compile a standard for testing.
And no, I can't do any programming, but if I can do anything else, like serving virtual coffee, I'll do it :D
Regards,
kontrakatze
Hi,
i forgot something totally. My cf cards were both formatted with Fat32. I guess this would make a difference to exFat, but now it's too late for testing today...
Should we set exFat to the list of standards for testing?
Something to add:
It is weird, the lighting situation seems to influence the write speed during the benchmark. With a lenscap on top I get repeatedly different speeds compared to lenscap off...
Could someone test this to be wrong or true?
Regards,
kontrakatze
Quote from: kontrakatze on March 23, 2014, 09:08:17 PM
Hi,
i forgot something totally. My cf cards were both formatted with Fat32. I guess this would make a difference to exFat, but now it's too late for testing today...
Should we set exFat to the list of standards for testing?
Something to add:
It is weird, the lighting situation seems to influence the write speed during the benchmark. With a lenscap on top I get repeatedly different speeds compared to lenscap off...
Could someone test this to be wrong or true?
Regards,
kontrakatze
So what's the final verdict? Is it definitely worth updating to this version or should we wait for the mystery update that might come out next month?
I hope the mystery update is a free C.500 to all ML users ;)....No!....oh well.
In my personal opinion , no , unless you want the ability to remove the bootflag , then yes.
Ive found the MLV modules on both 113/123 not reliable enough to rely on , but this is no problem as I prefer the audio out of my h4n anyway and syncing is not such a big hassle , but I have had more stopping using 123RAW than I did with 113RAW also my camera seems to heat up faster and run higher temps if only by 3 or so degrees but the most noticeable downside if you can call it that is that 123 seems to eat up battery life allot quicker than 113 (I should add that is just what SEEMS to be happening it could all just be my poor take on using both firmwares).
So what am I running on both my Mk3's ?, 123 mainly cause I cant be arsed to revert back to 113 and cause 123 seems to be the way forward even if it is a little bit less stable at the moment , there are of course no more nightly s for it at the moment so im holding my breath in anticipation for what is next-if anything.
Cheers
jafa
Before ML on my Mark 3 I could easily let the camera on over several days; thats not possible with ML 123; the power-consumption is really high
Quote from: fotogemeinschaft_de on March 25, 2014, 08:43:03 PM
Before ML on my Mark 3 I could easily let the camera on over several days
Quote from: jafa on March 25, 2014, 07:50:08 PM
also my camera seems to heat up faster and run higher temps if only by 3 or so degrees but the most noticeable downside if you can call it that is that 123 seems to eat up battery life allot quicker than 113
Proof please.
(I already did my part (http://www.magiclantern.fm/forum/index.php?topic=1573.0))
friggin yeah it worked, pretty awesome, just gotta get out there and shoot!
thanx.
ps- cf issue interesting, had to pull mine at present.
Hello,
I just installed it but i cannot find how to shoot video in RAW mode?
Thanks for help!
Module tab -> RAW_REC.MO or MLV_REC.MO -> Restart -> Enable RAW option via movie tab
THX!
with the version of March 26, I can not record at 50 fps at 1728x606 with 64 gb Komputerbay 1000x while with the version of March 17, I recorded without interruption ... the same thing happens to someone?
The two versions are 100% identical (look at the change log).
Quote from: a1ex on March 26, 2014, 06:16:48 PM
The two versions are 100% identical (look at the change log).
I noticed that the change log was empty. Why would someone want to update the build without any change to it?
Nanomad was experimenting with the build server.
Canon Menu HDMI Mirror works perfect shooting .RAW
You can connect any monitor by HDMI.
It's a revolution for me.
Quote from: budafilms on March 26, 2014, 08:02:38 PM
Canon Menu HDMI Mirror works perfect shooting .RAW
You can connect any monitor by HDMI.
It's a revolution for me.
AWESOME !
Quote from: budafilms on March 26, 2014, 08:02:38 PM
Canon Menu HDMI Mirror works perfect shooting .RAW
You can connect any monitor by HDMI.
It's a revolution for me.
with ML overlays?
what settings you using.?
Brand new 5D MK III (literally just opened it), formatted Transcend 64gb 1000x exFat on computer. Downloaded 1.2.3 ML compatible, and installed. Easy as pie. Not using SD card at all. I am fairly new to ML so I can't really speak to how things are working, but no need for 10 minute youtube install videos.
Shot some RAW footage at the upper end of the settings and it seemed to work fine - only a few minutes though. Will test it out more tomorrow.
Quote from: Jakobmen on March 26, 2014, 08:40:34 PM
with ML overlays?
what settings you using.?
No, with out overlays in the monitor!(yes in the viewfinder) But it's enough for work with a cameraman and a director!
Quote from: budafilms on March 27, 2014, 03:18:38 AM
No, with out overlays in the monitor!(yes in the viewfinder) But it's enough for work with a cameraman and a director!
I think what you want to say is; there are overlays in the
camera LCD (the viewfinder the the one you stick your eye in which is dark when the mirror is up) and there are no overlays in the external monitor via hdmi.
Quote from: ted ramasola on March 27, 2014, 04:01:43 AM
I think what you want to say is; there are overlays in the camera LCD (the viewfinder the the one you stick your eye in which is dark when the mirror is up) and there are no overlays in the external monitor via hdmi.
Exactly!
I tried taking various shots, 5 min, 2 min in full HD with .RAW ( I thought with external monitor .raw could be a problem but not, it's the same).
If you are using h264, and after you want to use .raw, take off the battery and start again.
Last week I loose lots of videos.
The rest works perfect.
A1ex it's the next Ironman. Or Canonman.
This is what is happening when i use a external monitor via hdmi https://docs.google.com/file/d/0B3Wn4pEshal_eHVxNC1rTEhGU2c/preview
the external monitor shows a clear picture but the camera lcd is just blinking.. i cant record ..
any pointers ?
Quote from: Jakobmen on March 27, 2014, 04:57:58 AM
This is what is happening when i use a external monitor via hdmi https://docs.google.com/file/d/0B3Wn4pEshal_eHVxNC1rTEhGU2c/preview
the external monitor shows a clear picture but the camera lcd is just blinking.. i cant record ..
any pointers ?
It's like your info button are pressing.
Take the battery out or format the card and copy ML again!
Thank you for your job!
I have tested W/R speeds for seven CF cards. Ver.1.1.3 is faster than ver.1.2.3. Return to 1.1.3. Hope 1.2.3. will be faster.
http://yadi.sk/d/Pbt-8juaLJFb4
How to post an image?
Quote from: budafilms on March 27, 2014, 04:49:30 AM
Exactly!
It's weird, when I use the new hdmi mirroring feature, there's no way to show ML overlays in the camera LCD. Pressing INFO button, just shuffles the normal Canon overlays.. :-\
Quote from: budafilms on March 27, 2014, 07:59:47 AM
It's like your info button are pressing.
Take the battery out or format the card and copy ML again!
ok its not blinking! ok the only thing showing on the Canon lcd is canons overlays not ML
@Jakobmen
You can have this problem back if you activate the "LV Display presets"
in ML Prefs menu
Hey guys just wanted to say thank you and chip in a bit.
I have just tried out my first RAW video on the Mark Free with a Hoodman UDMA 7 64GB CF and it went on until around 1:04mins without skipping frames. When it did, it automatically stopped recording. Checked temp and it was 41º up from 24º before recording.
I'm a bit concerned in the shutter count it says I'm over 100K (yeah, went on a timelapsing trip by the end of 2012-early 2013 and went berserk) and ML says it has too many shutter actuations. Is this something I should be worried about? Maybe start using silent pictures from now on?
Thanks again, keep up the good work!
Quote from: Jolly Roger on March 27, 2014, 11:18:14 AM
It's weird, when I use the new hdmi mirroring feature, there's no way to show ML overlays in the camera LCD. Pressing INFO button, just shuffles the normal Canon overlays.. :-\
Try Reply #183 ;)
Quote from: vstrglv on March 27, 2014, 11:10:04 AM
Ver.1.1.3 is faster than ver.1.2.3. Return to 1.1.3. Hope 1.2.3. will be faster.
Can you do a chart just like Ted did for 5D2 here?
http://www.magiclantern.fm/forum/index.php?topic=11205.msg108936#msg108936
You will have to cover raw_rec and mlv_rec on both 1.1.3 and 1.2.3. Please do the test with the March 17 builds for both firmware versions.
Since I still have 1.1.3 I can test that one first and then 1.2.3 but: MLV has so many configurations it would be insane to draw conclusions.
A chart with only RAW_rec with the different resolutions in 1x mode and 3x mode on 1.1.3 and 1.2.3 maybe?
To simplify things, you can just use the default configuration and some other configuration with all hacks enabled.
Of course, testing all possible combinations has exponential complexity (http://en.wikipedia.org/wiki/Time_complexity), but changing only one setting at a time (from the default configuration) will be also very helpful, as it will show the effect of each setting (and the complexity is linear).
If you have luma zebras enabled, remember they use zero CPU on 1.1.3, but quite a lot of processing power on 1.2.3.
Quote from: a1ex on March 28, 2014, 10:16:39 AM
Can you do a chart just like Ted did for 5D2 here?
http://www.magiclantern.fm/forum/index.php?topic=11205.msg108936#msg108936
You will have to cover raw_rec and mlv_rec on both 1.1.3 and 1.2.3. Please do the test with the March 17 builds for both firmware versions.
I'll try. But there is an accuracy question. It takes a long time for one card testing, so its temperature increases. But the higher temperature, the higher speed. FPS overwrite is on?
There is a test.
http://yadi.sk/d/DanyXgMqLPdpv
I can not insert a picture in the post...
Image link fixed //Audionut
Thank you!
can 1.2.3 be faster 1.1.3 or there are some limitations.
I have 1.2.3 and dreaming of 1080p 29.97 cont, but can rec 1-2 sec max.
my card from win indicates 114mb write. inside ml around 83. but with rec above 65 it tells me no way)
I installed ver. 1.2.3 over the latest Canon firmware. This is the first time I've ever used ML, and it would appear I missed a step because I have no RAW video option. I've been scouring these forums for an hour or so but I can't seem to find a concise answer. Any help would be appreciated.
Also if I want to uninstall it can I just put the Canon firmware and overwrite or is that somehow risky?
Quote from: GooDween on March 29, 2014, 12:40:25 PM
my card from win indicates 114mb write. inside ml around 83. but with rec above 65 it tells me no way)
Windows uses a write cache (http://en.wikipedia.org/wiki/Cache_%28computing%29). The reason why you should "eject" devices before unplugging them.
This (http://alex-is.de/PHP/fusion/downloads.php?download_id=9) will provide a more reliable speed reading in windows.
Quote from: Danielbyron on March 30, 2014, 05:37:58 AM
I installed ver. 1.2.3 over the latest Canon firmware. This is the first time I've ever used ML, and it would appear I missed a step because I have no RAW video option. I've been scouring these forums for an hour or so but I can't seem to find a concise answer. Any help would be appreciated.
Look in the modules menu, and enable the required module.
Quote from: Danielbyron on March 30, 2014, 05:37:58 AM
Also if I want to uninstall it can I just put the Canon firmware and overwrite or is that somehow risky?
Follow the instructions in the first post.
@vstrglv
No worries. Try using an image host that provides a direct link to the image.
http://postimage.org/
http://tinypic.com/
https://imgur.com/
etc.
Thanks for the help! Got raw up and running:)
92md in assd)
btw wich settings are best? cluster size fat or exfat?
If you are using the card specifically for raw recording, and speed is your priority, you should probably use the largest cluster size (http://en.wikipedia.org/wiki/Data_cluster) possible. If you also do image capture, then you may want to use a smaller cluster size to minimize wasted space.
You should also consider aligning (http://www.overclock.net/t/1226963/how-to-properly-re-align-your-ssd-hdd-partitions) the card partition.
I seem to recall a slight speed advantage to exfat. But this may simply have been placebo. Pretty easy to test this one yourself ;)
Quote from: Audionut on March 30, 2014, 07:59:17 AM
If you are using the card specifically for raw recording, and speed is your priority, you should probably use the largest cluster size (http://en.wikipedia.org/wiki/Data_cluster) possible. If you also do image capture, then you may want to use a smaller cluster size to minimize wasted space.
Doesn't make much sense to me. What is the cluster size range we are talking about?
Typical RAW image size today is between 10 MByte (for older cams) and 30+ MByte. Default cluster size is 0.5 KiByte and therefore (statistics jumping in) 0.25 KiByte are wasted for each image taken. That's about 0.0025 percent (worst case for older cams). Drive with 30 GByte will loose 0.75 MByte to overhead if filled with RAWs.
Now cluster size 128 KiByte. 64 KiByte lost for each file (statics again) and a 30 GByte drive will loose about 192 MByte as in 20 RAWs. I can live with that.
Please explain if I missed something and of course correct calculations I've done before breakfast.
Ciao
Walter
ok made via diskpart aligment and format to exfat.
Quote from: Walter Schulz on March 30, 2014, 09:00:38 AM
I can live with that.
Then do so :)
The point is, there
is a difference in
wasted space. I provided the reader, the opportunity to make his own decisions.
The wasted space can never be more then the cluster size,
for each file. So where we have extremely large files, such as raw video, the difference is virtually nothing. But if the user is also using JPG (lots of smaller files) capture (happens more often then you might otherwise expect), then the differences,
may become relevant.
Hello.
Currently i have no M3 in my hands - can someone help me out with a question:
I want to film with 60fps RAW with the M3 and a Komputerbay 64GB 1000x CF card.
How big (resolution) can i go? I just need about 10 second takes...
Thank you very much!
better run a movie ML bench for your card so u get an idea of your card's mb/s
also check here http://www.magiclantern.fm/forum/index.php?topic=5472.0 (http://www.magiclantern.fm/forum/index.php?topic=5472.0)
i shot 1 time RAW 720p @50fps with np..best is to experiment yourself and see which settings are good for your purpose
Has anyone tired recording the HDMI out on a recorder (atomos ninja,) etc.?
Here is an overview of ML powers: https://docs.google.com/spreadsheet/ccc?key=0AgQ2MOkAZTFHdFFIcFp1d0R5TzVPTVJXOEVyUndteGc#gid=5
But is this true: 1920x672 with 60fps?
That would be from stretch.
Small update:
- Magic Zoom fix for focus confirmation bars (http://www.magiclantern.fm/forum/index.php?topic=11137.msg109402#msg109402), from chris_overseas
- minor cosmetic fix for electronic level, also from chris_overseas
- mlv_rec updates merged from the unified branch (g3gg0)
- minor delay fine-tuning for zoom on half-shutter
Most of the other changes from the changelog apply to other cameras.
Quote from: mannfilm on March 30, 2014, 06:13:52 PM
Has anyone tired recording the HDMI out on a recorder (atomos ninja,) etc.?
I'm trying out a ninja blade, this weekend. It works great with the 5d Mkiii as long as the canon codecs are frame rates are matched. The HDMI start stop is very cool it really simplifies the whole process. This function doesn't seem to work when ML is running, the camera records to CF but the Blade doesn't start. I also use an Okii MC1 to trigger the start stain over USB, this doesn't seem to interfere with the functioning of ML. Having a video file with synced audio is also a big boon!
I'm at work now but I'll post some pics of the rig later.
Alex
Just uploaded latest nightly for 5DIII, green bars on magic zoom nice and clear, even for those with old eyes like me!
Many thanks
Garry
Should of soldo thanked Chris!
Wish I understood the codejoke from Alex...
hello,
Please, is it possible to keep this subject page ( Magic Lantern for 5D Mark III 1.2.3 ) prior ? not 1.1.3 and only 1.2.3 (except for comparation between these two ML firmware)
there is some (soon a lot) of questions and message out off concern here, and many responses possible in other forum pages...please take a time to make a search before posting here. otherwise, it's gonna be a mess soon
thank you. (from france)
and congratulation to the contributors...amazing work !
Long time ML user, first time posting on the forums. I did some test shooting RAW (1.2.3) for the first time on Friday and ran into a problem. Anytime we ran over the 4GB file size limit, approximately 50 seconds of shooting, the file would get divided up and look like this:
M28-1030.R00
M28-1030.R01
M28-1030.RAW
I then used RAWMagic to convert but I only get images that were all f#@$ed up. See link: http://i.imgur.com/quVjbAF.jpg
Should I be using a different converter software?
You could try the mlrawviewer.
Quote from: mixmastermike on March 31, 2014, 01:13:36 AM
I'm trying out a ninja blade, this weekend. It works great with the 5d Mkiii as long as the canon codecs are frame rates are matched. The HDMI start stop is very cool it really simplifies the whole process. This function doesn't seem to work when ML is running, the camera records to CF but the Blade doesn't start. I also use an Okii MC1 to trigger the start stain over USB, this doesn't seem to interfere with the functioning of ML. Having a video file with synced audio is also a big boon!
I'm at work now but I'll post some pics of the rig later.
Mike, is the HDMI output with ML installed better than the HDMI output stock? In other words, by using the external recorder along with ML are you recording RAW-esque level of detail or is it still the normal "mush" we are used to? Thanks
Hi,
Love the work being done to bring ML to 1.2.3 as well as solving the boot flag issue.
I tried the latest build on March 31 and noticed an odd brightness flickering issue on the LCD.
My LCD brightness is set on manual, I actually felt that the issue was less noticeable when set to Auto brightness.
If you actually go to the Canon menu for the brightness setting, you can see the little white arrow moving all around.
I reverted to the normal firmware by removing the bootflag and the LCD brightness was stable.
I also reverted to the 17 March build and again the LCD brightness was stable. I am now back on the older build because it was annoying me too much.
I wonder if anyone else experienced this issue.
Thanks :)
Quote from: Bassman2003 on March 31, 2014, 09:06:48 PM
Mike, is the HDMI output with ML installed better than the HDMI output stock? In other words, by using the external recorder along with ML are you recording RAW-esque level of detail or is it still the normal "mush" we are used to? Thanks
Its 8 bit 422, so nowhere near raw but it holds up a little better in post.
The reason I liked it was that you effectively get a proxy with sound (you have to connect a mini jack, from the camera or ZoomH6 in my case, into the blade to get this to work) canon protocol has HDMI without sound. This makes post audio syncing easy with plural eyes plus you can quickly show a client a clip that looks pretty good.
Thanks for your reply Mike. So the HDMI output quality is the same as if you never had ML installed?
Quote from: Bassman2003 on March 31, 2014, 11:28:43 PM
Thanks for your reply Mike. So the HDMI output quality is the same as if you never had ML installed?
Exactly
I feel really dumb for asking, but where is the download for ML for the 5D Mk III? Your download page only shows a version 2.3 released July 2012.
Quote from: Alex DeJesus on April 01, 2014, 12:30:33 AM
I feel really dumb for asking, but where is the download for ML for the 5D Mk III? Your download page only shows a version 2.3 released July 2012.
In the download page click "Nightly Builds" and then from the drop down list select 5D3.123-bleeding-edge
i have many frame drop using 31 march 2014 build on .raw file
i tried mlv, doesn't work for me
using komputerbay 1050x 128gig
Quote from: Kiongku on March 31, 2014, 09:42:44 PM
Hi,
Love the work being done to bring ML to 1.2.3 as well as solving the boot flag issue.
I tried the latest build on March 31 and noticed an odd brightness flickering issue on the LCD.
My LCD brightness is set on manual, I actually felt that the issue was less noticeable when set to Auto brightness.
If you actually go to the Canon menu for the brightness setting, you can see the little white arrow moving all around.
I reverted to the normal firmware by removing the bootflag and the LCD brightness was stable.
I also reverted to the 17 March build and again the LCD brightness was stable. I am now back on the older build because it was annoying me too much.
I wonder if anyone else experienced this issue.
Thanks :)
Yes - I also have the same flickering issue in LV from 2014-03-30 build.
Quote from: Hans_Punk on April 01, 2014, 11:25:59 AM
Yes - I also have the same flickering issue in LV from 2014-03-30 build.
Check your calendar ;)
Quote from: applewide on April 01, 2014, 08:28:13 AM
i have many frame drop using 31 march 2014 build on .raw file
i tried mlv, doesn't work for me
using komputerbay 1050x 128gig
Same here on 30th build , gone back to 17th - more stable on raw and mlv.
Highest recorded temp is 48 after two minutes continuous record RAW, is every one else getting similar temps ?
Using 5D III 1.2.3 without any crashes so far, but is it normal for automatic image display to be disabled with ML? Before ML, when I took a photo, the rear screen automatically showed the photo I just took (for 4 seconds as I have set in Canon menu). After ML, even with Canon menu still set to show image for 4 seconds, I get nothing on screen. I have to manually push the display button to see the image I took. Is there a workaround?
Quote from: jafa on April 01, 2014, 03:53:48 PM
Same here on 30th build , gone back to 17th - more stable on raw and mlv.
Highest recorded temp is 48 after two minutes continuous record RAW, is every one else getting similar temps ?
I'm getting similar temperatures, which is making me a little nervous. I haven't had the camera shut down on me, but does anyone know what temp one would expect the camera to shut down? It's definitely outside the specified operating temperature.
Quote from: Kiongku on March 31, 2014, 09:42:44 PM
Hi,
Love the work being done to bring ML to 1.2.3 as well as solving the boot flag issue.
I tried the latest build on March 31 and noticed an odd brightness flickering issue on the LCD.
My LCD brightness is set on manual, I actually felt that the issue was less noticeable when set to Auto brightness.
If you actually go to the Canon menu for the brightness setting, you can see the little white arrow moving all around.
I reverted to the normal firmware by removing the bootflag and the LCD brightness was stable.
I also reverted to the 17 March build and again the LCD brightness was stable. I am now back on the older build because it was annoying me too much.
I wonder if anyone else experienced this issue.
Thanks :)
+1 i also have flicker in my LCD, it's kind of annoying, but i think i can live with it.
Please add relevant information about screen flicker problems, here (https://bitbucket.org/hudson/magic-lantern/issue/1938/screen-flickering-in-manual-or-auto-lcd).
Quote from: Audionut on April 02, 2014, 07:51:01 AM
Please add relevant information about screen flicker problems, here (https://bitbucket.org/hudson/magic-lantern/issue/1938/screen-flickering-in-manual-or-auto-lcd).
It was an april fool by a1ex :P. No more problem now :) cheers
Quote from: Kiongku on April 02, 2014, 07:54:28 PM
It was an april fool by a1ex :P. No more problem now :) cheers
??? really? it was all a joke? haha cause i was getting worried
Today i installed the 123. I hesitated but for serious video for clients its easy to disable ML so i can use it at will
tried it because of the HDR video
just installed and the functions that i use work great!
I also put ML on the 650D but te 5D3 is sharper and have better iso
everything seems to be working..except help and info sections??? i just used the nightly build for 1.2.3.
(does boot flag still have to be installed?)
Looks like this is heading in a great direction!
I can't wait to see the day where we can get stable use from a 5D Mark III & wireless follow focus/external monitors/movi...
Productions would be epic!
Quote from: nikki on April 04, 2014, 05:05:24 PM(does boot flag still have to be installed?)
3 things needed to run ML properly:
Bootflag set on cam
Bootable card
ML files and directories on card
ok using raw and everything works ok...i had couple bad frames once with the early 31th build but couldn't reproduce and since then im with 17th build and np...we are ready for testing the 'real sensor upgrade' :D
Quote from: pv25pv on April 05, 2014, 12:30:24 PM
the 'real sensor upgrade' :D
... it is coming at a company near you. It is the legendary EOS 5D MarkIV :D :D :D
You''ll just have to wait a couple of years ;D
I don't think a1ex is suffering from prima aprilis praecox (IANAL). Still waiting for the bang and if it's the sound of a balloon popping ... well, I've done worse in times ...
There are tons of comparison videos out there, but I still wanted to do one for myself.
Not a super technical comparison either, because I didn't set the normal H.264 picture style to be most editable, nor did I record with all keyframes mode.
I finally got a fast enough card for 1920x960 24p continuous RAW recording (Lexar 1066x 32gb CF).
This is using the March 17 build of ML for 5Dm3 1.2.3
It's worked quite well, no pink frames or dropped frames for me.
Recorded in MLV 2.0 format without sound
Converted MLV to DNG with MLV Mystic
Edited in Lightroom
Final editing done with Premiere
www.youtube.com/watch?v=esmxEm2R56E
For those who prefer
vimeo, here's the
vimeo link, but it's in 720p
https://vimeo.com/91064331
Hi U-Type,
Thanks for the share. In the future, please consider sharing your video in the appropriate section (http://www.magiclantern.fm/forum/index.php?board=19.0).
This way, this thread remains focused on development.
Thanks.
I have 1.2.3 installed, everything seems to be working generally, but I'm having a lot of trouble recording at decent resolutions at 50/60fps. I'm recording to a new SanDisk Extreme Pro CF card (http://www.amazon.com/SanDisk-Extreme-CompactFlash-Memory-Card/dp/B00ECEVFFO/) but I'm unable to record at 1920x672 (1920x1080 when stretched by 1.61x in post) at 59.940fps.
The ML menu footer says this requires 129.0 MB/s, the card is supposed to feature a 150 MB/s write speed, so what am I missing?! I'm finding I have to dial things back to 1344x470 for the footer message to turn green, at which point the predicted bandwidth is 63.1 MB/s - surely this CF card should be able to handle more?
Run a disk benchmark on your computer on that card I bet it's not even close to the rating. This is generally the same for all cards. Plus I don't see too many people if anyone getting full res shots at 60p only at 24/30.
It's not ML its false advertising... or wishful thinking...
Quote from: thomasdiak on April 06, 2014, 06:30:26 PMThe ML menu footer says this requires 129.0 MB/s, the card is supposed to feature a 150 MB/s write speed, so what am I missing?!
The 5D3 is only capable of writing to CF cards at about 100MB/s, regardless of how fast your card is.
Quote from: a1ex on March 16, 2014, 03:26:45 PM
Uninstallation:
1) Run Firmware Update from your ML card.
2) Follow the instructions.
- uninstallation is equally easy (update firmware and follow the instructions)
When I try to uninstall ML from 5D III (1.2.3) by going to Wrench menu=> "firmware version"=> then I get the message "Memory card containing firmware is required to update" even though the memory card with ML is inside the camera.
I don't get the "instructions" to follow to uninstall. What am I missing? Should I just go to "Format card" and choose "Format card. remove ML" option?
The reason I am trying to uninstall ML is I still cannot get auto image display after taking the shot, which is a real time-waster.
Quote from: drjlo on April 07, 2014, 03:39:39 AM
When I try to uninstall ML from 5D III (1.2.3) by going to Wrench menu=> "firmware version"=> then I get the message "Memory card containing firmware is required to update" even though the memory card with ML is inside the camera.
Make sure the firmware file is on the card.
ML5D3123.FIR
Quote from: drjlo on April 07, 2014, 03:39:39 AM
The reason I am trying to uninstall ML is I still cannot get auto image display after taking the shot, which is a real time-waster.
This functionality is working fine here. Try adjusting the image review setting, powering off/on the camera. Or, try resetting Canon settings.
Quote from: Audionut on April 07, 2014, 04:54:09 AM
Make sure the firmware file is on the card.
ML5D3123.FIR
This functionality is working fine here. Try adjusting the image review setting, powering off/on the camera. Or, try resetting Canon settings.
Thanks.
All my issues seemed to have gone away once I formatted the card, reset the camera to factory defaults, then reinstalled ML. Thank goodness this did not clear my C1-C3 custom settings and Lens AFMA values :)
Quote from: Stedda on April 06, 2014, 07:06:01 PM
Run a disk benchmark on your computer on that card I bet it's not even close to the rating. This is generally the same for all cards. Plus I don't see too many people if anyone getting full res shots at 60p only at 24/30.
Thanks - what is a good utility to run a disk benchmark (Mac)? I've used AJA System Test and saw some pretty shocking results - with a 1GB sample file, averaging around 28-30MB/s write speed, and 36-38MB/s read speed. That could be a limit of running the test through a USB2 card reader though right?
Quote from: chris_overseas on April 07, 2014, 02:56:35 AM
The 5D3 is only capable of writing to CF cards at about 100MB/s, regardless of how fast your card is.
I'm not even close to that limit though - captures seem to drop out at around 70MB/s, almost 100MB/s below my card's theoretical limit.
I realize capturing 1080p at 50/60fps may be wishful thinking (Is it? Has anyone done it?) but surely I should be able to handle more than the 60~MB/s I'm currently seeing. Is there a list of ML settings that are critical to handling higher data rates?
Quote from: thomasdiak on April 07, 2014, 03:25:49 PM
That could be a limit of running the test through a USB2 card reader though right?
Yes. USB 2.0 is good for 60 MByte/s data rate in theory only. Practical ceiling (overhead issue) is about 38 MByte/s.
Ciao
Walter
I've been running the bleeding edge dist for about 3 days now. Im not into video so I use the shoot features only, such as bracket and interval. There were times that the bracket fired strangely, one frame every 5-10 seconds. Seems like something was eating proc cycles and sending the whole camera into a confused state. Had to yank the battery as turning off didnt purge the sensor memory like normal behaviour.
This happens in 1 from 7-10 sessions of turning the bracket on. Not sure if this information is helpful at all.
p.
If you can record a video of what's going on, will be helpful.
If you can find a way to reproduce, that would be even more helpful.
Silly question 8)
Can someone please tell me how to get rid of bootflag. And when i get rid of bootflag, can i still shoot RAW videos?
Run the installation process (firmware update) from "bleeding edge" nightly and do as advised on the screen: Wait for 30 seconds timeout and bootflag is gone.
And no, you won't be able to use Magic Lantern at all.
Quote from: Audionut on April 06, 2014, 03:10:20 AM
Hi U-Type,
Thanks for the share. In the future, please consider sharing your video in the appropriate section (http://www.magiclantern.fm/forum/index.php?board=19.0).
This way, this thread remains focused on development.
Thanks.
The guy is still over excited seeing raw vid recorded on 5d3... Yes it is beyond comparison.
Quote from: Walter Schulz on April 08, 2014, 12:42:04 PM
Run the installation process (firmware update) from "bleeding edge" nightly and do as advised on the screen: Wait for 30 seconds timeout and bootflag is gone.
And no, you won't be able to use Magic Lantern at all.
Thanks dude
Quote from: Danne on March 31, 2014, 07:48:52 PM
You could try the mlrawviewer.
This worked! Thank you
I can record 1920x1080 25fps continuously with sound on a komputerbay 64gb 1000x
However, when I am using my Alphantron EVF it stops just after a few seconds. When I change it to 24fps I can record continuously again with sound using my EVF. Card spanning will not help me recording 25fps...
Does this mean a faster card won't help me recording 1080 25fps with sound as the HDMI is basically absorbing some speed? In RAW 1.0 25fps 1080p is possible anyway, but I love recording sound along with my Sound Devices Mixpre-d fieldmixer connected to the 5d3.
Any suggestions to let the HDMI not slow it down?
Hello guys,
I know Im out of discussion but last couple days Im watching NAB 2014 from canonrumors.com live blog.
As it seems the new "fashion style" for videographers is to be able during shooting especially those who shooting raw
to can apply LUTs instantly via a monitor or in the camera and watch how this is going to look and take a taste before continuing shooting the rest.This is so exciting that I would like to ask if it is something
that we can expect from ML team. In reality Im thinking to paste a few LUTs in my SD card (5D3 owner) and select which I want to apply to my selected clip. Ofc this means that we must have flawless playback and with the limitation of cf card speeds I don't know if its possible.. besides that as an idea I would like to be able to change a few parameters into my camera before I send the files into my editing system such as: highlights, shadows, midtones, white balance etc.
Again sorry for being out of topic I just thought to share a few new fresh things that I saw at NAB, keep the amazing work ML!
There already is a LUT at play in MLV_PLAY to render the debayered footage as full colour. Interesting question though, anxious to see the proceeding comments.
Hi I'm sorry if it's already well asked,
what is the most stable ML version?
My main reason for ML is video autofocus.
I am hoping to get 4K video recording at some stage (here's hoping) ... along with autofocus, wouldn't that be awesome!
Also hoping to get f/5.6 cross type AF at the sides (currently only f/4).
If there is no autofocus i will use magic zoom to focus manually, but without a flip screen would be a big challenge (I use it 99% handheld)
Thanks
I use for work March 17th. Keep in touch! ;)
I was teaching someone to install and run ML on his 5d3 today and since I only have a 5D2 and 7D i was limited to the my experience with my cams.
Using the latest bleeding edge, I did manage to get it up and running. The only thing I could not figure out was FPS over ride.
Is is still buggy on the 5d3?
Reason is, I could not get it to "behave" as expected.
At 23.976 it seems fine however I tried lowering to say 5 or 10, I was expecting the LV to be so bright already, however it seems to my eye, only the framerate is slowing down but the exposure remained unchanged.
I checked in the exposure tabe and see exposure sim is set to movie. I had my 5d2 beside it and it was behaving as expected. Was there a setting on canon menu or ML menu that I missed?
Isn't that the way it should be, as your are only changing the number of pics per second and not the aperture or shutter speed?
Please guys ! this is not general discussion here....this topic is about 5D MK 3 " 1.2.3 firmware"only ....you may found interesting respons by making a search or create a topic....otherwise it's gonna be a mess here.....thank you for understanding
Quote from: ted ramasola on April 11, 2014, 05:49:05 AM
I was teaching someone to install and run ML on his 5d3 today and since I only have a 5D2 and 7D i was limited to the my experience with my cams.
Using the latest bleeding edge, I did manage to get it up and running. The only thing I could not figure out was FPS over ride.
Is is still buggy on the 5d3?
Reason is, I could not get it to "behave" as expected.
At 23.976 it seems fine however I tried lowering to say 5 or 10, I was expecting the LV to be so bright already, however it seems to my eye, only the framerate is slowing down but the exposure remained unchanged.
I checked in the exposure tabe and see exposure sim is set to movie. I had my 5d2 beside it and it was behaving as expected. Was there a setting on canon menu or ML menu that I missed?
In the FPS Override tab, choose advanced and then select 'Low Light' as opposed to 'Exact Frames'.
Guys,
have someone solved the issue where if using the HDMI mirroring the ML menu isn't shown?
Thanks!
Quote from: aliman84 on April 11, 2014, 11:05:31 AM
In the FPS Override tab, choose advanced and then select 'Low Light' as opposed to 'Exact Frames'.
Thanks aliman84.
yesterday I recorded ~250GB of raw video using 5D3 1.2.3 and MLV_REC.. I works without hangs. I had issues with my Transcend 1000X 64GB CF card with 1080p 23.98fps 16:9. Sometimes it recorded without issues but I had a lot of scenes ended after 3 seconds (first skipped frame). I had also problem on ~20 scenes with black level but I fixed it with mlv_dump --black-fix option.
Hi Guys,
After installed Magic Lantern for 5D Mark III 1.2.3, why my 5D mark iii main dial was dead, restored back to Canon firmware is back to normal. I have tried several times.
Any idea?
Thanks
Quote from: Audionut on April 06, 2014, 03:10:20 AM
Thanks for the share. In the future, please consider sharing your video in the appropriate section (http://www.magiclantern.fm/forum/index.php?board=19.0).
This way, this thread remains focused on development.
Thanks.
Im having some problems over here...
I have the 1.1.3 version installed in my 5d3 and the nightly builds for it... well, when i click the firmware update button to install the version 1.2.3 from canon (with the new firmware inside the sd card), the camera goes to a loading screen and then return to the main menu and some messages like "DATA/FONTS.DAT retry, not found and you have to install al ml files" appears at the top of the screen. I already tried to reinstall ml, to do the bootflag again... but this message always appears. I searched in the computer for this folder in my sd card but there is no .dat file in there. what i have to do?
First: What do you want to do?
Run your camera without ML, just updating to Canon's firmware version 1.2.3?
Format your card using your cardreader, insert it into cam, format it there, copy Canon's firmware file content (*.FIR) to card and proceed with firmware update.
I've been lightly testing the 5D3 april 10th nightly and haven't got any problems so far.
One question though. Is it OK to use the camera with a battery grip? Did read in the installtion guide that it should not be installed with one attached.
I use mine with the grip all the time... its always on through install, upgrades, etc...
Quote from: FaniSkogen on April 14, 2014, 10:57:08 AM
One question though. Is it OK to use the camera with a battery grip? Did read in the installtion guide that it should not be installed with one attached.
The advice not to install with a grip is just the guide being extremely cautious. Like Stedda I install, use, and uninstall ML with the grip attached the entire time without any issue at all.
So far the only minor bug I've noticed is that ML only reports the battery percentage for one battery rather than an average of the two. I did have a quick look to see if I could figure out how to add support for the additional battery to ML but it wasn't obvious (given my level of knowledge at least). The Canon menu and top LCD still work fine for reporting battery levels so just use those instead.
Back in the old 550D days, there were a couple of guys who removed the grip, but forgot to put the battery door back. Result: they believed the camera got married somehow with the grip (they believed ML caused the camera not to start without the grip).
Example: https://bitbucket.org/hudson/magic-lantern/issue/239/550d-3rd-battery-grip-issue
With ML RAW and audio, is the HDMI out clean for clients and crew watching and/or recording editable HDMI with a ninja for backup?
Please let me know if this is not the right place to report this problem.
5DIII
Not a major problem. It has to do with the crop marks. Global Draw (I've tried all modes) is on and when I turn Cropmarks off the Cropmarks remain on my monitor. If I turn the camera off and back on the Cropmarks are gone. I've repeated this several times and I get the same thing. This only happens when I have the HDMI frame rate from the camera to the monitor set at 60i.
If the HDMI out is set to 24p then the Cropmarks turn on and off when they are supposed to, but they do not fill the monitor.
Quote from: mannfilm on April 15, 2014, 03:25:37 AM
With ML RAW and audio, is the HDMI out clean for clients and crew watching and/or recording editable HDMI with a ninja for backup?
Ninja with 5D Mkiii
Framing is perfect.
The only thing that doesn't work is the auto start recording via the HDMI trigger, this works without ML. It would be an awesome feature as we would have Proxies with sound already created by the ninja, with the exact start and stop point.
Mods - Should I post this as a feature request?
How do you get full hd output through the hdmi while recording RAW or MLV?
I only get 720p? When I change monitor resolution with the info button to get full hd output It won't record RAW but h264 again as i am not in the ML mode.
Have anyone achieved continious or near 1080p 29.976?
I am now on komputerbay 1050 32gb. write speed on pc up to 125
but after 5 sec on mlv and 12 sec on rawmod without any features it stops.
Quote from: mixmastermike on April 15, 2014, 05:15:26 AM
Ninja with 5D Mkiii
Framing is perfect.
The only thing that doesn't work is the auto start recording via the HDMI trigger, this works without ML. It would be an awesome feature as we would have Proxies with sound already created by the ninja, with the exact start and stop point.
Mods - Should I post this as a feature request?
OK ...but no raw or prores yet?
Quote from: nikki on April 15, 2014, 03:29:50 PM
OK ...but no raw or prores yet?
Camera is recording raw, the Ninja Blade is recording Prores. I will double check the resolution I just use this as a monitor with focus assist etc and a playback device.
Ill shoot a little today and transfer it to the Mac and check it out to confirm
Quote from: GooDween on April 15, 2014, 02:50:36 PM
Have anyone achieved continious or near 1080p 29.976?
I am now on komputerbay 1050 32gb. write speed on pc up to 125
but after 5 sec on mlv and 12 sec on rawmod without any features it stops.
Older builds of MLV with "card spanning on" have achieved Full HD at 30p, however this is very early stages with 1.2.3 Firmware and MLV is also pretty new and still in the development stages.
At present the buffers are not writing at optimal performance, the Dev's are currently working on image issues and errors with the new firmware.
Quote from: pobox on April 15, 2014, 09:46:53 AM
How do you get full hd output through the hdmi while recording RAW or MLV?
I only get 720p? When I change monitor resolution with the info button to get full hd output It won't record RAW but h264 again as i am not in the ML mode.
I'll double check this for you later today, I literally plugged it in and it worked off the bat I just had to hook up the audio.
In last weeks build the HDMI trigger was working too, so that when you pressed record on the ninja blade, it triggered the 5D MKiii to start recording Raw. This was a sweet feature I hope we can get this back. I have a OKII USB controller that triggers the camera to start recording, really helpful if the camera is on your shoulder. This has also stopped functioning, this was a real time saver just one button triggered the camera to record RAWand the Ninja to record Rrores with sound.
Quote from: pobox on April 15, 2014, 09:46:53 AM
How do you get full hd output through the hdmi while recording RAW or MLV?
I only get 720p? When I change monitor resolution with the info button to get full hd output It won't record RAW but h264 again as i am not in the ML mode.
The image on the left is the Prores HQ 1920 x 1080 (.MOV) file, on the right is the first dng in the raw sequence. both full HD.
What input settings do you have on the Ninja?
ok thanks just want to know that i am on bleeding edge of possibilities)
btw if it interesting here, card spaning with newest build don't help at all.
on previous build it helps sometimes.
and again in win i get 125 for write. and on ml test 88-95.
raw rec gives me few secs more before skip.
if i can help i'll try)
Hi guys, love the magic lantern software. I've used it since release of this 1.2.3 version and have shot maybe 2000 images with it over many many hours and tried most stills features and the only thing I had issues with came about last night. Was doing star trails and using the intervalometer, and that worked perfectly. However, after use, even with it turned off, it always activates at half shutter.
It was ok until I first turned it on, and worked fine for 120x 30 second images and stopped as it should, but disabling it in the menu no longer turns it off.
What have I missed?
Quote from: Stu in Blackpool on April 15, 2014, 11:04:08 PM
Hi guys, love the magic lantern software. I've used it since release of this 1.2.3 version and have shot maybe 2000 images with it over many many hours and tried most stills features and the only thing I had issues with came about last night. Was doing star trails and using the intervalometer, and that worked perfectly. However, after use, even with it turned off, it always activates at half shutter.
It was ok until I first turned it on, and worked fine for 120x 30 second images and stopped as it should, but disabling it in the menu no longer turns it off.
What have I missed?
Put battery out and check again putting off. If not, format the SD card and put again ML. Maybe is a bug.
i dont have a cf card reader is there another way to get the raw files from the camera? when i try and use the usb cable no raw files appear.
A decent USB 3.0 cardreader is just 19 US$ away. I recommend Kingston FCR-HS3.
Quote from: Stu in Blackpool on April 15, 2014, 11:04:08 PM
Was doing star trails and using the intervalometer, and that worked perfectly. However, after use, even with it turned off, it always activates at half shutter.
It was ok until I first turned it on, and worked fine for 120x 30 second images and stopped as it should, but disabling it in the menu no longer turns it off.
Nice catch, should be OK now. Please try any combination you may think of, and let me know if it doesn't behave as expected.
If anyone wonders why I'm sometimes slow at reviewing pull requests, it's because I smell this kind of bugs (annoying, but subtle enough so they get reported after many many months). This bug was introduced from a rushed merging in October 2013 (my fault, sorry).
And since I didn't have the occasion to use the intervalometer lately... you get the idea.
Quote from: a1ex on April 16, 2014, 06:36:34 PM
Nice catch, should be OK now. Please try any combination you may think of, and let me know if it doesn't behave as expected.
If anyone wonders why I'm sometimes slow at reviewing pull requests, it's because I smell this kind of bugs (annoying, but subtle enough so they get reported after many many months). This bug was introduced from a rushed merging in October 2013 (my fault, sorry).
And since I didn't have the occasion to use the intervalometer lately... you get the idea.
Thanks ever so much mate. Love your work with this system.
I know your main focus is video, but for for me, its added so much to my stills ability that i use every day that I cant imagine the camera not having these features now.
Specifically useful for me are the bulb timer and intervalometer.
To be able to do this in camera, while sat in the car browsing the internet is just amazing.
Thanks so much. :)
Getting read to upgrade. I saw the bleeding edge was removed from the download description.
How is the classic RAW video mode running these days?
Can you still format your recording card to exfat to avoid splits?
A1ex/Mods
Not sure if this should go here or in "Feature Requests"?
I did some testing this morning and I have confirmed that the HDMI trigger that starts recording on an external recorder, is not working.
I tried RAW_REC and MLV_REC with various different settings sound on/off etc resolution changes with no effect.
Im guessing that the ML code doesn't have the instruction in it to send the signal down HDMI to start/stop recoding.
From Atomos
QuoteSynced REC Trigger and Timecode
The Blade provides frame accurate timecode and start stop triggers over HDMI from many cameras, including Canon, Sony, Panasonic, Nikon, JVC, RED and ARRI. It also features LANC and rolling timecode trigger for those older cameras that don't have start stop flag protocols on board. The Blade additionally has tally lights to indicate start time.
This function works without ML running. It's a really good function as it provides instant frame accurate proxies in ProRes (with sound if hooked up correctly) to edit with and also frame accurate play back for anyone on set or even talent wanting to see how the last shot looked.
I realize that this may not be high priority, but if anyone has a moment this is a real kick ass feature, this massively speeds up post production and elevates functionality to that of a dedicated video camera with real time playback.
Regarding the 04/16 build 1.2.3:
As soon as I hit record all the overlays disappear except for the recording time. No focus peaking, audio meters, shutter/ISO information etc. Any ideas?
Hi,
just installed the ML on my 5D, could someone try to press the magnifyer while recording raw ?
in my case it hangs up the full camera (need to take the battery out)
thanks
Thomas
@Stu in Blackpool
Please be mindful of the image size rules (http://www.magiclantern.fm/forum/index.php?topic=934.0).
@Shield
Look for the GD option in mlv_rec
@4u2fast
I'm not 100% sure, but I don't think you can zoom while recording. Otherwise, yes, it crashes.
@mixmastermike
Could you please tell which build worked for HDMI trigger and MLV raw recording. I want to use it with my Ninja but haven't any luck with the latest build.
QuoteIn last weeks build the HDMI trigger was working too, so that when you pressed record on the ninja blade, it triggered the 5D MKiii to start recording Raw.
Whilst on the discussion of REC trigger, is there any chance the the REC_KEY feature will be enabled on the 5DIII 1.2.3 build in the near future? (it seems to be enabled for all other cameras) I would really appriciate the half shutter command to start/stop the video. (So I can make my own external button trigger input)
I imagine others would find it useful to help develop other external start/stop controlers - possibly being able to split the command to sync start audio recorders or hdmi recorders?
Already put this in feature requests a few weeks back, but without any response. I wondered if there is a technical reason why the 5D3 is the only camera that has no rec_key options within ML?
@ hans_punk & @ rigs
I will have a look at the specific builds and try a few out, I'm not sure exactly which ones they were, if i remember correctly I did have one build working. Then I had "threads failed" error message and yesterdays build didn't work at all. I'll do some digging to try and isolate what builds worked and post the results this weekend, Ill also try going back to 1.1.3 and report the findings there.
Quote from: a1ex on March 16, 2014, 03:26:45 PM
It's out! (http://builds.magiclantern.fm/)
Installation:
1) Format the card from the camera.
2) Make sure you are running Canon firmware 1.2.3 (http://www.canon-europe.com/Support/Consumer_Products/products/cameras/Digital_SLR/EOS_5D_Mark_III.aspx?type=download&page=1).
3) Copy ML files on the card and run Firmware Update.
Can this be a separate SD card and not the CF card you are shooting to, or does the ML firmware have to be on the shooting CF card. If it can be a separate SD card is there a speed requirement for the SD card?
Is there somewhere I can find out this information?
Need help please. First time user of 5D Mark III. So i am here https://bitbucket.org/hudson/magic-lantern/branch/5D3-123 but how or where do I download the files that I need to install in my CF card? is there like a zip file that contains everything? Thanks a lot!
@elarturex
Got to the first page of this post. "It's out" is the link. Click it to got to the download page.
@unfilmde Thanks a lot!
hi there,
thank you for the new build. it's nice to see, that some people invest so much time into this and we can profit from it!
just switched from 1.1.3 to 1.2.3
after a quick test I have now .RAW files instead of .MLV files
Could someone tell me why and what the difference between these formats is?
thanks guys
Quote from: templar on April 18, 2014, 11:03:42 PMCould someone tell me why and what the difference between these formats is?
http://www.magiclantern.fm/forum/index.php?topic=7122.msg59525#msg59525
-> Some technical facts
hi there
I ve just install yesterday the 1.2.3 on my canon mark iii
Fist I didn't find the M menu, then when I go to the 0110 menu I click on show module
I have instead of the M menu a triangle but no raw record option anywhere
somebody can help me?
thx!
Tab left to 0110.
Set RAW_REC.MO or MLV_REC.MO to ON, restart cam, access movie tab, enable RAW and configure it's options.
I have no raw rec mo or mlv rec in the 0110 menu
i have:
modules debug
memory browser
screenshot 10s
sump rom
don't click me
burn in tests
benchmarks
show tasks
show cpu
show gui vets
show edmac
Tab left to 0110.
<- 0110 -> i
Ciao
Walter (BPSG)
ok I understand
it works
thanks a lot !
Can somebody inform is there a chance to change the live HDMI output resolution/mode from original 1080i50 with help of Magic Lantern to 1080p50?
Thanks,
Quote from: Walter Schulz on April 18, 2014, 11:15:12 PM
http://www.magiclantern.fm/forum/index.php?topic=7122.msg59525#msg59525
-> Some technical facts
Ok so the MLV is the newer format with more features/info. So it hasn't yet merged into the 1.2.3 version? Or can you select the format?
thanks
its in the 1.2.3...load MLV module,restart and rec in MLV format (same with RAW module if u wanna rec in RAW)
do you know why my files have .mlv at the end instead of raw
Quote from: osk33no on April 20, 2014, 06:05:50 AM
do you know why my files have .mlv at the end instead of raw
http://www.magiclantern.fm/forum/index.php?topic=7122.0
First post has everything you need to read up...
Quote from: osk33no on April 20, 2014, 06:05:50 AM
do you know why my files have .mlv at the end instead of raw
The old way to get RAW, the first development was .RAW (you have that module too).
The last, with more advantages, is .MLV that include RAW and a lot of information to get more benefits. And right now is in development too.
.RAW doesn't have Audio.
.MLV yes, putting an audio Module.
Depends your OS, you should find a way to convert MLV to DNG.
Take a look in the beginning of the post.
Hope this help you.
Good Lantern!
By the way, in this new 1.2.3 I get a lot of fail notification on the camera screen using MLV. It is not skipping frame or the recording would stop by the settings. Nothing that I can notice when I actually watch the clips, apart from other notifications when I convert the MLV to dng in mac, saying unknown block, skipping block.... The exact message on the camera screen is: FAILED queue: (number)failed: (number) required.
how is progressing 1.2.3 version of ML? Is it any close to what is on 1.1.3 ? And if anyone has any experience with eye-fi wifi card?
Thought I'd post again.
Can the ML 1.2.3 be on a separate SD card and not the CF card you are shooting to, or does the ML firmware have to be on the shooting CF card. If it can be a separate SD card is there a speed requirement for the SD card?
Is there somewhere I can find out this information?
Question: there was a setting in firmware 1.1.3 that let me hold down play or menu or info when starting up to use custom settings.. forgot what its called.. is that in 1.2.3?
http://www.magiclantern.fm/forum/index.php?topic=8499.msg78568#msg78568
thank you i want looking under user guide.. :)
Quote from: unfilmde on April 21, 2014, 12:20:23 AM
Thought I'd post again.
Can the ML 1.2.3 be on a separate SD card and not the CF card you are shooting to, or does the ML firmware have to be on the shooting CF card. If it can be a separate SD card is there a speed requirement for the SD card?
Is there somewhere I can find out this information?
Yes it can. Take a look at http://www.canonrumors.com/forum/index.php?topic=20060.msg388253#msg388253 (http://www.canonrumors.com/forum/index.php?topic=20060.msg388253#msg388253) there is a whole discussion on it if you scroll up in that thread.
@rpt
Thanks!
looks like the 1.2.3 firmware development process has not been very active recently....
When do you think there will be a stable version of 1.2.3 ML?
0 to 24 hours before the day following release date.
Quote from: Walter Schulz on April 22, 2014, 10:11:40 PM
0 to 24 hours before the day following release date.
Walter, you seem to know a thing or two about software releases ;)
(http://postimg.org/image/idb7i6g3j/)
Quote from: vovkinson on April 22, 2014, 02:59:09 PM
looks like the 1.2.3 firmware development process has not been very active recently....
I manage to download a new nightly at least once a week for 5D III 1.2.3 is that not up to par with the aggressive schedule you've set for the Devs of a free software? ::)
I'm just being angry at myself for not taking part of the development process :)
Quote from: Stedda on April 23, 2014, 02:11:09 PM
I manage to download a new nightly at least once a week for 5D III 1.2.3 is that not up to par with the aggressive schedule you've set for the Devs of a free software? ::)
I took a quick look at most recent build for 5DIII 1.2.3 (2014-04-22) and noticed 'UNDO' step.
Does it mean 'no update' to 2014-04-16 version?
just tested 04-22-2014 1.2.3 and it crashed. reverted to 04-16-2014
http://www.chiark.greenend.org.uk/~sgtatham/bugs.html
sorry, I was not aware of this form of reporting bugs. Unfortunately I deleted the logs.
Hello everyone, I'm looking to use ML for stills only. Just tried the latest build and see that in the "Shoot" menu there's only an A +2EV. Is there no plans of have up to 9 shot brackets for exposure?
Press Q. If there is a little Q showing in a menu item it is a good idea to go for it.
Thanks!
Hi everybody, I've been testing last two builds of ML, still not the 04-22-2014 one. They have worked very well for me, I've been shooting stills, and .MOV video. I don't have any fast card enough to shoot RAW video, so I can not say anything about this feature.
My question is: For those people that doesn't need to shoot RAW video, and only shoot in .MOV, is secure enough? In my tests I didn't have any corrupted files or frames, but I read at the begining of the post, that for video is better the 1.1.3 version, or this was only for RAW video?
I have to shoot for professional use, and I don't want to have any problem with the footage. And I would like to use the LV DIGIC peaking (for easy focus), the shooter fine tuning (to avoid screens and lights flickering), and the display information that ML has.
Thanks a lot to the big effort of developers, ML is an amazing tool.
As far as I know (could be mistaken) there's no stable ML version for 5DIII (yet).
So, I guess it's not a good idea to use alpha/betta/gamma test versions for your professional work.
Quote from: vovkinson on April 24, 2014, 02:03:32 PM
As far as I know (could be mistaken) there's no stable ML version for 5DIII (yet).
So, I guess it's not a good idea to use alpha/betta/gamma test versions for your professional work.
Thank's vovkinson, I know there is no stable version for 5DIII yet, but in my experience testing latest ML builds, I find it is stable enough for the work I do. I've been testing ML during last two weeks, with no problem at all.
I just wanted to know, if somebody had any problem shooting video in the original Canon format .MOV, all I have found in the forum were RAW video issues.
There are no issues till now.
I installed on 1.2, but it doesn't work. The ML menu doesn't appear when I press 'erase' and theres no addition to the regular UI. What's wrong?
jeremynative,
If you describe how you were installing ML (step-by-step) - maybe somebody will help you out here. Your statement "just does not work" wouldn't find many responses.
hello..i just wanted to ask if we have to uninstall ML 1.2.3 every time we wanna shoot canon's mov.
or by just pulling out the sd card the camera runs canons original firmware (with no issues i hope)
thank you
You can shoot with the original mov even with ml. But if you enable the raw module its disabled.
So..every time you wanna shoot mov you just turn off the raw module. Its simple like that.
I found out the issue with my camera. I get a 'irregular battery' message when I load my camera, so that interrupted the installation process. Had to take the battery attachment off and it worked, works with it reattached after installation too.
May be important to include that in the installation instructions
Thanks for sharing !
I'm trying to find a solution to display correctly ML overlays on my Lilliput HDMI screen with no mirroring.
Full screen 16:9 image without any overlays :
https://www.dropbox.com/s/wximeno42xphqs6/2014-04-26%2015.34.40.jpg
Screen with ML overlays:
https://www.dropbox.com/s/dqtvdcyv64wyppr/2014-04-26%2015.34.53.jpg
Screen with Canon options:
https://www.dropbox.com/s/1n2iiw9vo2emxug/2014-04-26%2015.42.40.jpg
As you can see ML top and bottom bars are not displayed properly. I think screen width and height are set to wrong values. I was trying to change settings in Display-> Advanced Settings > Screen Layout but it's not a solution. I think top and bottom bar should be resized to fit 16:9 image and placed above and below cropped 16:9 image. Is there a possibility to add new screen layout to ML configuration? I can do it myself but I need a little hint ;)
I solved with ML settings somehow on 1.1.3 firmware. Now the white info are around the image in black zone.
I still can't get mine to stop flickering on 5d3 when connected on a few HDMI tvs to make sure it's not my monitor
Does anybody know why crop layout disappear when hitting the record button in mode RAW_VIDEO(MLV) ?
However, in RAW_VIDEO (not MLV) I can see the layouts and focus peaking "stars" during recording.
Hi,
Sorry if this is the wrong place to be posting this but felt like the best place to ask.
Any idea why I keep getting this pop up coming up when I'm shooting raw video? It doesn't happen immediately but has happened every time I've shot something in raw and requires me turning the camera off in order to get rid of it.
Not sure if it always says the exact same thing.. but it is always along the same lines.
I've attached a photo of the screen so you know what I'm talking about.
Thanks in advanced for the help!
PHOTO: https://flic.kr/p/nn6Bgu
it's called CRASH. There should be LOG file on your SD card.
So is there a place that I should post that log file to try and help out the ML team?
Depending on how big the log file is, you can copy the contents directly to the forum, using the code tags.
If it's rather large, there are plenty of free file hosts, and you can link to the forum.
Awesome thanks! Well this is what I've ended up with.
ML ASSERT:
hdr->blockSize > 0
at mlv_rec.c:1969 (mlv_prepend_block), task raw_rec_task
lv:1 mode:2
Magic Lantern version : Nightly.2014Apr16.5D3123
Mercurial changeset : 72846f0bc65b (5D3-123) tip
Built on 2014-04-16 16:33:51 UTC by [email protected].
Free Memory : 130K + 3926K
Quote from: marekk on April 26, 2014, 03:58:47 PM
I'm trying to find a solution to display correctly ML overlays on my Lilliput HDMI screen with no mirroring.
Full screen 16:9 image without any overlays :
https://www.dropbox.com/s/wximeno42xphqs6/2014-04-26%2015.34.40.jpg
Screen with ML overlays:
https://www.dropbox.com/s/dqtvdcyv64wyppr/2014-04-26%2015.34.53.jpg
Screen with Canon options:
https://www.dropbox.com/s/1n2iiw9vo2emxug/2014-04-26%2015.42.40.jpg
As you can see ML top and bottom bars are not displayed properly. I think screen width and height are set to wrong values. I was trying to change settings in Display-> Advanced Settings > Screen Layout but it's not a solution. I think top and bottom bar should be resized to fit 16:9 image and placed above and below cropped 16:9 image. Is there a possibility to add new screen layout to ML configuration? I can do it myself but I need a little hint ;)
I'm having the same problem. Please let me know if you find a fix or a way I can solve this myself.
Quote from: alphaandomegafilms on April 15, 2014, 04:29:35 AM
Please let me know if this is not the right place to report this problem.
5DIII
Not a major problem. It has to do with the crop marks. Global Draw (I've tried all modes) is on and when I turn Cropmarks off the Cropmarks remain on my monitor. If I turn the camera off and back on the Cropmarks are gone. I've repeated this several times and I get the same thing. This only happens when I have the HDMI frame rate from the camera to the monitor set at 60i.
If the HDMI out is set to 24p then the Cropmarks turn on and off when they are supposed to, but they do not fill the monitor.
Crash Report:
Just finished shooting some RAW footage .RAW and I disabled the RAW module and started to shoot footage and the camera crashed. I will try to recreate. Here is the log.
ASSERT: IsSuiteSignature( hSuite )
at ./PackMemory/PackMem.c:599, task RscMgr
lv:0 mode:3
Magic Lantern version : Nightly.2014Mar17.5D3123
Mercurial changeset : 48e7ddebc1b9 (5D3-123) tip
Built on 2014-03-17 10:57:11 UTC by
[email protected].
Free Memory : 132K + 3799K
I also just installed the most recent nightly build to see if that helps. I will let you know.
When HDMI monitor is connected to 5D3 1.2.3 in mirroring mode we can't display ML bars on 5D3's LCD screen because camera sets new value to lv_disp_mode. When there is no mirroring enabled lv_disp_mode is set to 0, when canon overlays are displayed on the screen lv_disp_mode is set to 1.. and finally when mirroring is enabled lv_disp_mode is set to 2 (with or without canon overlays). I replaced all pieces of code which check lv_disp_mode value with "(lv_disp_mode == 0 || lv_disp_mode == 2)" and lv_disp_mode (true) with lv_disp_mode == 1 and now I'm able to display ML bars on LCD screen with mirroring enabled:
https://www.dropbox.com/s/uf5oi7ln28w0879/2014-04-27%2016.06.44.jpg
It's not a final solution because ML bars are displayed also with canon overlays...
(replaced code: zebra.c, debug.c, menu.h, gui-common.c, lens.c, tweaks.c)
marekk
Do you know how to make crop layout show up in MLV_VIDEO ? I managed to set it up to display 2.5:1 ratio but as soon as I hit the record button - it disappears and shows me the regular Canon's 1920x1080 screen.
Again it only happens in MLV_VIDEO, IN RAW_VIDEO - everything is ok.
Thanks in advance!
Quote from: vovkinson on April 27, 2014, 05:06:29 PM
marekk
Do you know how to make crop layout show up in MLV_VIDEO ? I managed to set it up to display 2.5:1 ratio but as soon as I hit the record button - it disappears and shows me the regular Canon's 1920x1080 screen.
Again it only happens in MLV_VIDEO, IN RAW_VIDEO - everything is ok.
Thanks in advance!
hmm maybe try to set your ml config to default ?
global_draw - Allow . Got it!
Temperature is climbing up even when i dont shoot or taking pictures.
5d3 1.2.3
latest build 2014-04-24 22:25:04 +0300
komputerbay 64 gb x1000
camera start at 22-26c , after 10 min when camera is on it shows 44c
Any ideas?
Best
David
Quote from: Djoni_P on March 16, 2014, 09:55:03 PM
First of all, THANKS A LOT for your work with ML!
I've been waiting for a 1.2.3 release forever!
I installed it but I can't find the M tab for raw video.
The M tab seems to be replaces with a triangle symbol tab.
I fixed it!
Thanks a bunch!
Hi Djoni, I'm very new to this and encountered the same problem, how did you end up fixing it? Thanks for all the great info in here.
What temperature is critical for the sensor? Is 44C already worrying or not? I really don't have any references.
The camera has it's own thermal protection... as in Canon firmware.
I would not worry about 44C... electronics heat up in use. If the camera is on it's going to generate heat.
Also if you do a search you'll find many people with readings around 50+ C and it is thought that the sensor being read is not 100% accurate or correct.
Quote from: Stedda on April 28, 2014, 01:30:38 PM
The camera has it's own thermal protection... as in Canon firmware.
I would not worry about 44C... electronics heat up in use. If the camera is on it's going to generate heat.
Also if you do a search you'll find many people with readings around 50+ C and it is thought that the sensor being read is not 100% accurate or correct.
Thank you Steda,
well when you have an orange background around 50c on the ml menu you get worried...
I am about to go on production of 5 days narrative shooting using 5d3 1.2.3
So how should i address this info?
Best
David
David,
please let us know how it go
Quote from: vovkinson on April 28, 2014, 02:54:31 PM
please let us know how it go
Thank you Steda,
well when you have an orange background around 50c on the ml menu you get worried...
I am about to go on production of 5 days narrative shooting using 5d3 1.2.3
So how should i address this info?
Best
David
Well if i wont fill confident i will not go with this version and then there will be nothing let you know :)
David, I wouldn't blame you :)
Here you go you can read though this to see averages and what not... in all the reading and time I've been on here I've yet to see a post where a camera has melted down or been damaged from heat.
You're not the first to do extended recording....
http://www.magiclantern.fm/forum/index.php?topic=9673.0
Post 8 has graphs by camera model. You're well below the average.
Also see post 30 where it discussed the temps are highly unreliable and assumed to display higher than they really are.
Personally I don't think twice about the temp displayed... the camera will regulate it's self. I think it's a case of give someone more information than they'd normally see and they'll turn it into a big deal.
Quote from: Stedda on April 28, 2014, 03:58:41 PM
Here you go you can read though this to see averages and what not... in all the reading and time I've been on here I've yet to see a post where a camera has melted down or been damaged from heat.
You're not the first to do extended recording....
http://www.magiclantern.fm/forum/index.php?topic=9673.0
Post 8 has graphs by camera model. You're well below the average.
Also see post 30 where it discussed the temps are highly unreliable and assumed to display higher than they really are.
Personally I don't think twice about the temp displayed... the camera will regulate it's self. I think it's a case of give someone more information than they'd normally see and they'll turn it into a big deal.
Thank you so much Stedda for that link...
Well after reading i can say - to bad that this temp info shown the way it shown.
if its highly unreliable why get people worried for nothing?
Going to do some heavy duty test, shoot something like 5 takes of 7 min long shots one after the other and see whats happened.
Best
David.
You need to read the thread and decide for yourself... but please try to search the forum/internet and find a melted camera or one destroyed by heat. You won't be able to because it's a non issue.
ML RAW has been around close to a year if it was a problem it'd be well known by now....
Quote from: Stedda on April 28, 2014, 05:51:29 PM
You need to read the thread and decide for yourself... but please try to search the forum/internet and find a melted camera or one destroyed by heat. You won't be able to because it's a non issue.
ML RAW has been around close to a year if it was a problem it'd be well known by now....
I wrote you after i read the thread,
I searched the forum for "temperature" and "5d3" but this thread didnt showed up. thank you for showing this to me.
i think ml should give the user the option to view the temp on lv or not.
Best
David
Ok,
I took 5 shots one after the other 7 min each 1920x1080 24 fps with audio. temp now is at 55c (annoying orange background) but camera perform good.
Something i noticed that happened twice out of four, is if i format the cf card on cam (komputerbay 64gb 1000x) when i come back to lv screen becomes black and i have to pull the battery out to get it work again.
i think it happened after cf card got full and record stopped. going to try to reproduce and report.
Also after recording 7 min it does not show the right remaining space on card - 64gb card does not supposed to have 59.4 gb of free space after 7 min recording.
maybe i did something wrong.
using last build.
Anyway regard the temp, looks like its a no issue.
Best
David.
I noticed if you switch live view off and back on it'll show the remaining space on card. Not sure if it's correct value or not. Some "refresh counter" procedure would be required in the next build.
QuoteAlso after recording 7 min it does not show the right remaining space on card - 64gb card does not supposed to have 59.4 gb of free space after 7 min recording.
Quote from: vovkinson on April 28, 2014, 10:23:18 PM
I noticed if you switch live view off and back on it'll show the remaining space on card. Not sure if it's correct value or not. Some "refresh counter" procedure would be required in the next build.
It's not a issue with 1.2.3 firmware. We need some code in mlv_rec to refresh it.
Quote from: marekk on April 29, 2014, 03:02:50 PM
It's not a issue with 1.2.3 firmware. We need some code in mlv_rec to refresh it.
Good to know,
Thank you marekk
Best
David
Quote from: marekk on April 27, 2014, 04:25:11 PM
When HDMI monitor is connected to 5D3 1.2.3 in mirroring mode we can't display ML bars on 5D3's LCD screen because camera sets new value to lv_disp_mode. When there is no mirroring enabled lv_disp_mode is set to 0, when canon overlays are displayed on the screen lv_disp_mode is set to 1.. and finally when mirroring is enabled lv_disp_mode is set to 2 (with or without canon overlays). I replaced all pieces of code which check lv_disp_mode value with "(lv_disp_mode == 0 || lv_disp_mode == 2)" and lv_disp_mode (true) with lv_disp_mode == 1 and now I'm able to display ML bars on LCD screen with mirroring enabled:
https://www.dropbox.com/s/uf5oi7ln28w0879/2014-04-27%2016.06.44.jpg
It's not a final solution because ML bars are displayed also with canon overlays...
(replaced code: zebra.c, debug.c, menu.h, gui-common.c, lens.c, tweaks.c)
That's great! Having magic lantern overlays work on the built in screen while also using an external monitor is the one extra feature I want from ML. Would you share your version of the magic lantern files so I can try it out?
can this change be included in nightly builds so we would able to test it?
Quote from: marekk on April 29, 2014, 03:02:50 PM
It's not a issue with 1.2.3 firmware. We need some code in mlv_rec to refresh it.
Sure, just tell us how to do that.
Keyword: reverse engineering
I thought marekk knew :)
Quote from: a1ex on April 30, 2014, 02:33:22 PM
Sure, just tell us how to do that.
Keyword: reverse engineering
Quote from: a1ex on April 30, 2014, 02:33:22 PM
Sure, just tell us how to do that.
Keyword: reverse engineering
ha ha :)
Quote from: Mei Lewis on April 29, 2014, 09:04:07 PM
That's great! Having magic lantern overlays work on the built in screen while also using an external monitor is the one extra feature I want from ML. Would you share your version of the magic lantern files so I can try it out?
I would also love this feature to be implemented into the latest magic lantern build.
Marekk, is there any way to inject your code into the latest nightly build?
Quote from: achangsta on April 30, 2014, 11:28:37 PM
I would also love this feature to be implemented into the latest magic lantern build.
Marekk, is there any way to inject your code into the latest nightly build?
Fresh compiled version of ML with overlays on LCD (mirroring enabled):
https://www.dropbox.com/s/8ejsn7zn6eh1sdp/5D3_hdmi.zip
USE IT FOR TESTS ONLY AND ON YOUR OWN RISK
Great thanks! Will give it a go.
Quote from: marekk on May 01, 2014, 02:45:11 PM
Fresh compiled version of ML with overlays on LCD (mirroring enabled):
https://www.dropbox.com/s/8ejsn7zn6eh1sdp/5D3_hdmi.zip
USE IT FOR TESTS ONLY AND ON YOUR OWN RISK
great! thanks!
Today i update firmware to 1.2.3 and install this version magiclantern-Nightly.2014Apr24.5D3123
And all OK!!! a1ex the best!!!:) No pink or other strange things.
Full roundtrip from Chmee's raw2cdng 1.5.0.beta3 -> Davinci Resolve -> offline proxy -> Premiere CC -> aaf/edl to Davinci and back to Premiere.
Only one strange was happend. XML from Premiere don't conform right in Resolve..... Resolve sey's "the clip .... failed to link because the timecode extents do not match any clip in the Media Pool" But AAF and EDL work correct.
Thank you artyg!
Can I ask you why did you choose the "roundtrip" so long?
Is possible to cut in davnici and export the clip to adobe premiere for final "makeup"?
I noticed when I import clip from adobe to davinci - I lost the effects applied in premiere... .
Quote from: artyg on May 02, 2014, 10:15:46 AM
Today i update firmware to 1.2.3 and install this version magiclantern-Nightly.2014Apr24.5D3123
And all OK!!! a1ex the best!!!:) No pink or other strange things.
Full roundtrip from Chmee's raw2cdng 1.5.0.beta3 -> Davinci Resolve -> offline proxy -> Premiere CC -> aaf/edl to Davinci and back to Premiere.
Only one strange was happend. XML from Premiere don't conform right in Resolve..... Resolve sey's "the clip .... failed to link because the timecode extents do not match any clip in the Media Pool" But AAF and EDL work correct.
Congrats on the 1.2.3 ML achievements so far (the bootflag issue being one really important one)! I also noticed the "experimental badge" (I forgot the excact phrase) was removed from the 1.2.3 nightly builds.
I guess this is a stupid question, with no definite answer. Still, I hope some of you could share some thought about the stability of the 1.2.3 nightly build as of today? Many stability issues still needing a lot of work? Sorry again for posting this question - but it's so hard to get a sense of where we all are in the thrilling ML development. I know testing and contributing is the main factor and I will do that as well :)
Happy to report, the 24th April build is highly stable and can handle audio, 27 fps,
1920x1080 without any issues. Card spamming was off and the card used was 1066x.
Better still the video plays back on MLViewer 1.1.5 without a hitch straight from the card. Not so previously.
Few observations, the last file before the card fills up will corrupt if the recording overshoots the card capacity. Don't know how to handle this. Second, miss the crop mode for magnified larger size frames. Lastly, where do I get hold of the H.264.ini files to run bit rate variations. When I press the H.264 option the error is that the H.264.ini file is missing.
Quote from: vovkinson on May 03, 2014, 09:12:07 PM
Can I ask you why did you choose the "roundtrip" so long?
Is possible to cut in davnici and export the clip to adobe premiere for final "makeup"?
I noticed when I import clip from adobe to davinci - I lost the effects applied in premiere... .
Hi, vovkinson (sorry for offtop - are you russia? :)) I use this "long" roundtrip, because this is the maximum quality and flexability trip... I make offline clip and edit it in Premiere, then I grade final edit in Resolve and then back for final edit/vfx compositing. I strongly advise you to read Alexis Van Hurkman - The Color Correction Handbook 2nd Edition. One of the first chapters cover this topic ;) Good luck.
Today will test magiclantern-Nightly.2014May03.5D3123
is there anything new in May03 release? changelog is empty
cheers.
oh i just saw its about CANON_SHUTTER_RATING..no idea what this is for anyway :)
Hi g3gg0,
Things are doing great with the ML firmware. I need one serious help though. Yesterday, for the very first time, I formatted my CF card as exFat enabled to check how much the card can record in one go. The setting on my 5d Mark 3 was ML sound on, 1920x1080p with the mlv_rec activated. Card was the sandisk 1066x 32gb. The camera ran smoothly for 6 minutes. Then the card filled up and the camera threw up an error - cannot replicate it now. As a result, I cannot view the recorded video on my camera with the mlv player. What am I doing wrong?
I am on the 5th may build. I have had this problem since the very beginning. The last file before the card fills up always spoils the party.
Reminder: the MLV thread is this one: www.magiclantern.fm/forum/index.php?topic=7122
and the post-processing area is this one: http://www.magiclantern.fm/forum/index.php?board=14.0
help me, why i can't record 1080p in 29.97
i bought new card toshiba 1066 64)
in bench it show for first 4 writes over 104mb 108-112
ml tells me i need about 103 for 29.97 for continious.
but it skips on 10-11 sec.
how people shoot 29.97?
Last weekend I recorded ~150 mlv files using latest ML for 5D3 1.2.3. No problems at all.
with 29.97? in 1080p?
settings please card, cluster size.
Quote from: GooDween on May 06, 2014, 12:07:14 PM
with 29.97? in 1080p?
settings please card, cluster size.
1080p 23,976 fps, 2,39:1
cards: Sandisk CompactFlash Extreme Pro 64GB (160 MB/sec)
Transcend 64GB Compact Flash 1000x
how did you format your CF cards? in camera or pc? Thanks.
Quote from: marekk on May 06, 2014, 11:33:58 AM
Last weekend I recorded ~150 mlv files using latest ML for 5D3 1.2.3. No problems at all.
I'm new to ML so bear with me. I am on the Mac platform. Can someone direct me to a link that explains how to go about installing the latest version of ML for the 5D Mark iii firmware version 1.2.3?
The way I'd like to work is purchase an SD card for the Magic Lantern Software and record to a CF card (I guess letting the camera format the CF card). When I want to shoot still with Canon's 1.2.3 firmware, I'd like to be able to remove the SD card.
Do I simply format the SD card in camera, then mount on my Mac and copy all the files to it. Then run the firmware update to ML 1.2.3?
Do I need to make the SD card bootable or is this automatic?
So I'm looking for explicit instruction for ML 1.2.3 NOT ML 1.1.3.
I hope I am clear and making sense and thank you in advance or TIA!
Quote from: unfilmde on May 06, 2014, 05:30:29 PM
Can someone direct me to a link that explains how to go about installing the latest version of ML for the 5D Mark iii firmware version 1.2.3?
First page, first entry.
And... how to upgrade from an earlier build to the most recent? Remove SD card, format and copy new files? Thanks | P
With firmware 1.2.3?
Just download nightly build, extract contents and copy files and directory to card. Done.
I ve tried the firmware on canon 5d m3 but ma able to use it only at 1728x972.. with superior resolution the recording stops and I have a trascendent and lexar 32 gb 1000x..
probably I am doing something wrong but am a bit frustrated..I an not saying it is bette blackmagic cinema camera but at leat that its simpler..
any advice?
Quote from: marekk on May 06, 2014, 11:33:58 AM
Last weekend I recorded ~150 mlv files using latest ML for 5D3 1.2.3. No problems at all.
You mind telling which particular build you use
where did you buy your cards? ebay?
If I was "frustrated" with magic lantern, I would buy blackmagic cinema camera and call it a day. Nobody's here guarantee 100% working firmware. Read forums, do your search and you'll find the info you're looking for.
As a forum member I just appreciate what A1ex and other guys do for us. If it does not work for you just go back to factory setting...
Quote from: psantia on May 06, 2014, 10:20:03 PM
I ve tried the firmware on canon 5d m3 but ma able to use it only at 1728x972.. with superior resolution the recording stops and I have a trascendent and lexar 32 gb 1000x..
probably I am doing something wrong but am a bit frustrated..I an not saying it is bette blackmagic cinema camera but at leat that its simpler..
any advice?
Hi there,
is there a way to get rid of the "FPS override: ..." text when recording RAW? Except from disabling this function ;-) I tried searching this forum but didn't find any clue.
Many thanks in advance,
Andrew
Quote from: ultimatemale on May 07, 2014, 01:41:49 AM
You mind telling which particular build you use
It was a ML code compiled on my Mac, May 1.
Video:
http://www.magiclantern.fm/forum/index.php?topic=11765.0
Workflow: mlv_dump > [ Davinci Resolve -> Cinelog -> Arri Log-C -> Prores 4444 ] -> FCPX
Hi again,
I just hooked up an external monitor and enabled mirroring. When I record H.264 there is no glitch when beginning but when I stop the recording the video freezes for about 1/2 a second. Didn't check to see if that behavior happens when not running ML. Any thoughts anyone?
BTW, much of what made me take the plunge and get a 5D mk3 is due to the energy that all you contributors put into ML, usability enhancements, the raw video option and all. My work so far could not have been done without this. Thanks so much for your time and effort! I'll try to make it up by working at creating even better videos :-)
Cheers,
Andrew
where did you buy your cards? ebay?
If I was "frustrated" with magic lantern, I would buy blackmagic cinema camera and call it a day. Nobody's here guarantee 100% working firmware. Read forums, do your search and you'll find the info you're looking for.
As a forum member I just appreciate what A1ex and other guys do for us. If it does not work for you just go back to factory setting...
Hi, yes one ebay and one amazon, well am not saying Magic Lantern is bad . it is a very good thing and I do appreciate very much the work done. it' s that i 've find it difficult to record video.and to understand everything ..it is not easy..I have the camera stopping all the time in 1920x1080..unless if I crop a lot , but i dont like crop so much ..depends what is it for.I can soot only 1729x 1008...The thing is that if i have to shoot something for work I would be very uncertain if to use raw with the last built 1.2.3 it is not so stable and i think needs cards to go with that does not exist for the moment.When I switched from canon 5d mrk 2 to 3 I thought was good think to do but actually the 5dm2 was better to use it for video since there is a stable firmware...I did not get it first..in case I can shoot with the camera firmware no problem..it is I did not mind shooting raw..to have a bit more of film look.But we will see maybe in the next months there is going to be a more stable firmware for canon 5d m3.More over I can not use mlv with sound because on my I mac with mac os 10.9.2 there is no converter to dng or pro res.
But we will se..I might be lucky and find the right resolution...I am just new to this.. before I had a hached gh2 also..and was very good.,...
Quote from: Fioritura on May 07, 2014, 05:15:33 PM
I just hooked up an external monitor and enabled mirroring. When I record H.264 there is no glitch when beginning but when I stop the recording the video freezes for about 1/2 a second. Didn't check to see if that behavior happens when not running ML. Any thoughts anyone?
After installing the version Marek compiled I get nice ML overlays on the internal screen. Yes! BTW, when I start raw recording there is a 2-3 second outage on the external screen (SmallHD AC7), but stopping the recording does not seem to effect the video transmitted.
Cheers,
Andrew
Quote from: Walter Schulz on May 06, 2014, 05:36:57 PM
First page, first entry.
So just copying the files to the SD cards makes the SD card bootable?
No.
If you are on a mac, search
MacBoot - a Card Preparer for OSX
if you are on PC
Eoscard
ML for 5D3.123 comes along with an installer. No need to run those tools. Read first page of this thread, first post.
Quote from: Walter Schulz on May 07, 2014, 08:46:00 PM
ML for 5D3.123 comes along with an installer. No need to run those tools. Read first page of this thread, first post.
Walter,
I have read the first post many times. It is not clear. When I unstuff the zip file there is an autoexec.bin, a folder ML and ML5D3123.FIR which is the firmware.
Are you saying when the files are copied to the SD card and the card is inserted into the 5D Miii, the camera will automatically see the autoexec.bin and run as an installer?
Being new to this, what is obvious to you is not to me.
TIA!
Quote from: unfilmde on May 07, 2014, 09:59:52 PM
I have read the first post many times. It is not clear.
Quote from first page:
QuoteInstallation:
1) Format the card from the camera.
2) Make sure you are running Canon firmware 1.2.3.
3) Copy ML files on the card and run Firmware Update.
Clear now?
I would have to agree. I have no knowledge of code or any of the inner workings of how any of this stuff actually works. Most of us are used to a button that says install on a Mac or PC and the rest is done for you. I would love to take advantage of ML but I always wondered why there are no official ML videos on the site that just take a novas step by step through the setup process from downloading the proper build to formatting cards all the way through shooting.
I've written step by step instructions on something in my field for people who have no experience doing what I do and I always have to be wary that they don't know as much as I do, and can't interpret or fill in the blanks like I would. I have to make sure that every step is "dummy proof" and listed out.
I've been searching through forum postings for months now and I'll be honest, I still don't feel 100% comfortable giving it a try. Perhaps it's just me, but i'm sure there are others out there who'd love to take advantage of this awesome feature but just aren't savvy enough to jump right in, especially when a Mark III costs over 3k.
J
Quote from: jrcreative on May 07, 2014, 10:28:37 PM
I've written step by step instructions
Quote
Installation:
1) Format the card from the camera.
2) Make sure you are running Canon firmware 1.2.3.
3) Copy ML files on the card and run Firmware Update
Feel free to send a1ex your suggestions.
Ciao
Walter
once ML is installed successful, can you opt to use it or not when you turn on the camera or if the SD card with ML is in the camera will it always boot up with ML? I remember using the previous firmware you had to hit the trash can etc. Is all that still necessary?
Thanks
J
Top of page -> User guide -> FAQ -> Second Q
:) The nightly Build worked for me without any alarming issues. The install literally took 3 minutes..... Thank you! Cant wait for the stable release!
Audio works when recording video! Im a noob for canon but if there is anything I can do to help finding bugs let me know.
-Trainwreckfilms
Quote from: Fioritura on May 07, 2014, 06:22:13 PM
After installing the version Marek compiled I get nice ML overlays on the internal screen. Yes! BTW, when I start raw recording there is a 2-3 second outage on the external screen (SmallHD AC7), but stopping the recording does not seem to effect the video transmitted.
Cheers,
Andrew
You should to disable Extra Hacks or Memory hack in MLV_REC options..
Quote from: marekk on May 08, 2014, 10:20:27 AM
You should to disable Extra Hacks or Memory hack in MLV_REC options..
OK, I'll try that next chance I get. Thanks!
Cheers,
Andrew
Anybody in the NYC area using the latest build with their Mark III that I can speak with directly. I'd love to ask a few direct questions to someone with experience using ML in my area.
Thanks,
Jason
Hi guys,
Im receiving my Lexar 64gb 1066x cards tomorrow and I cant wait to test out the ML Raw on my 5D3.
I just got a few questions if anyone could help me answer.
1. Should i start with 1.2.3 or try 1.1.3 first?
2. Where can I find the right camera settings for RAW on this forum? (stuff i need to switch on or off in camera settings)
Thx in advanced!
Dan Estee
Quote from: idan_estee on May 08, 2014, 06:14:37 PM
Hi guys,
Im receiving my Lexar 64gb 1066x cards tomorrow and I cant wait to test out the ML Raw on my 5D3.
I just got a few questions if anyone could help me answer.
1. Should i start with 1.2.3 or try 1.1.3 first?
2. Where can I find the right camera settings for RAW on this forum? (stuff i need to switch on or off in camera settings)
Thx in advanced!
Dan Estee
Hi Dan, I jumped right into using the version that supports 1.2.3. Seems to work fine so far.
Cheers,
Andrew
I am new to ML for the 5d3 (I've used it before but never on my own gear or on a 5d3), and I was wondering which build is the most stable if I just want zebras, peaking, intervalometer, and controlling bit rate? I am shooting a project where internet access will be sparse for about 2 weeks.
I have canon firmware 1.2.3 and have no intention of shooting RAW video or doing anything more complicated than I have already stated.
If it is the most current nightly build, then great! If it is something else, any suggestions are appreciated.
Thanks
is there a way of having mirror enabled and have ml stuff in the mark iii screen while having a video feed to an external monitor?
Quote from: marekk on May 01, 2014, 02:45:11 PM
Fresh compiled version of ML with overlays on LCD (mirroring enabled):
https://www.dropbox.com/s/8ejsn7zn6eh1sdp/5D3_hdmi.zip
USE IT FOR TESTS ONLY AND ON YOUR OWN RISK
Hi Marekk, has this feature been integrated into the nightly builds yet?
Cheers,
Andrew
Quote from: Fioritura on May 09, 2014, 07:57:22 AM
Hi Marekk, has this feature been integrated into the nightly builds yet?
Cheers,
Andrew
OK, looking at the changelogs it appears the last significant additions were on April 24. Probably not an easy task ;-)
Quote from: Fioritura on May 07, 2014, 08:46:58 AM
is there a way to get rid of the "FPS override: ..." text when recording RAW?
Disabling "Extra hacks" does the trick, although I think the FPS override announcement should take care of it's disappearance on it's own.
BTW, what is the preferred way to report (potential ;-) bugs? Is it OK to mention them in the camera related section or should I file create a Mantis-entry or some such?
Cheers,
Andrew
Quote from: marekk on May 01, 2014, 02:45:11 PM
Fresh compiled version of ML with overlays on LCD (mirroring enabled):
https://www.dropbox.com/s/8ejsn7zn6eh1sdp/5D3_hdmi.zip
USE IT FOR TESTS ONLY AND ON YOUR OWN RISK
A sure way to make the camera crash is to enable the 5x zoom, hook up an external HDMI display and start recording in raw mode. A static image was displayed on the screen, turning the camera off did not change a thing, but popping out the battery did the trick.
Cheers,
Andrew
No, code is not complete. ML overlays should be disabled when canon overlays are enabled.
Quote from: Fioritura on May 09, 2014, 07:57:22 AM
Hi Marekk, has this feature been integrated into the nightly builds yet?
Cheers,
Andrew
Hello everybody!
VERY GREAT JOB TO ALL YOU GUYS!!!!
I have a question: I'm still using ML 5D3-1.1.3. version, waiting to upgrade to 1.2.3. firmware because it is an irreversible upgrade.
Do the 1.2.3. version including all the features of 1.1.3. version?
Thank you,
Lorenzo
Quote from: lureb74 on May 09, 2014, 11:36:43 AM
because it is an irreversible upgrade.
it's not true ;)
Quote from: lureb74 on May 09, 2014, 11:36:43 AM
Hello everybody!
VERY GREAT JOB TO ALL YOU GUYS!!!!
I have a question: I'm still using ML 5D3-1.1.3. version, waiting to upgrade to 1.2.3. firmware because it is an irreversible upgrade.
Do the 1.2.3. version including all the features of 1.1.3. version?
Thank you,
Lorenzo
Despite what Canon says, it is NOT an irreversible upgrade. Myself and many others have upgraded and downgraded between 1.1.3 and 1.2.3 many times. To downgrade just flash the Canon 1.1.3 firmware over 1.2.3 like you normally would.
The codebase for both ML versions is virtually the same, the only differences in functionality are listed in the first post of this thread.
Ah ok!
So, what about the bootflag question? if I upgrade to 1.2.3., it will solve it? And if I downgrade back to 1.1.3., what append?
Quote from: lureb74 on May 09, 2014, 11:52:09 AM
Ah ok!
So, what about the bootflag question? if I upgrade to 1.2.3., it will solve it? And if I downgrade back to 1.1.3., what append?
Read Read Read :)
Magic!!!
update
i am using latest ml
- sound is working
- 1920x1080 is working raw version 2
- using lexar 32gb 1000x
if i use komputerbay 1060x 128gb, it will not work for this mode, i returned it already
will buy lexar from now on, the VDO is superb quality
:) :) :)Thanks to everyone who made it possible!
8) 8)
+1
Quote from: ss300000 on May 10, 2014, 06:42:43 PM
:) :) :)Thanks to everyone who made it possible!
8) 8)
2014-05-07 05:01:01 +0700
this build has a problem with beeping, please have a look
when i press test ok it works
but when i press record it doesn't make the beep sound
works fine here
http://www.chiark.greenend.org.uk/~sgtatham/bugs.html
Hello everyone...I'm sorry if this has been answered already but am a little stuck with this!
Just bought my 5d mkiii...and installed the 'Charlie Locke' version from post Reply #807...however I have deiced to use the latest version.
I'm confused by a few things though, and hopefully someone on here can shed some light.
1. I cannot seem to uninstall it with the 'firmware update' method...it will update with the card in and says 'boot done' smiley face but doesn't load the page that says 'move the mode button to change boot'!!!
So I have decided to just put the new version on the disk and try to boot it from that...nothing happens just red loading light!
What am I missing as I put all the new files on the disk and have 1.3.1 firmware in...but it doesn't boot. Do I need to uninstall the previous ML first? If so...how do I do that if it doesn't let me do it with the firmware update?
This is very frustrating.
Thanks for any advice
Which firmware version is installed on your cam? 1.1.3 or 1.2.3?
Quote from: a1ex on May 11, 2014, 05:46:33 PM
works fine here
http://www.chiark.greenend.org.uk/~sgtatham/bugs.html
hi alex
thanks for your quick response
for RAW version 1, yes it is working with BEEP
for RAW version 2, no it doesn't work with the BEEP, I just tried the latest one, I am positive, can you please send MLV binary please, should be a quick easy, I would fix it if i could
Quote from: a1ex on May 05, 2014, 11:33:00 AM
Reminder: the MLV thread is this one: www.magiclantern.fm/forum/index.php?topic=7122
RAW and MLV are not the core of ML, they are just applications (sure, very popular ones). There is a forum area dedicated to raw recording (http://www.magiclantern.fm/forum/index.php?board=49.0), so please discuss raw issues there.
I prefer this thread to be about core issues specific to 5D3 (in particular, problems introduced in 1.2.3 that did not exist in 1.1.3).
Hi.
Yesterday I shot 2 and 3 min continuous MLV files with 1920*1080 25p with sound.
The card was 32 GB 1066x lexar.
The space in the card was misreported after shooting 4 min. it was showing 25 GB empty and then recording stopped and got this message "card file system error?"
The empty space on card was still showing 25 GB
I removed the battery and restarted it was showing 0.2 MB
Any idea? I know this is a bug report but I couldn't post to bugs page somehow.
Thanks.
Quote from: ilkerc on May 12, 2014, 09:42:08 AM
Hi.
Yesterday I shot 2 and 3 min continuous MLV files with 1920*1080 25p with sound.
The card was 32 GB 1066x lexar.
The space in the card was misreported after shooting 4 min. it was showing 25 GB empty and then recording stopped and got this message "card file system error?"
The empty space on card was still showing 25 GB
I removed the battery and restarted it was showing 0.2 MB
Any idea? I know this is a bug report but I couldn't post to bugs page somehow.
Thanks.
It's not a issue with 1.2.3 firmware. It need some code in mlv_rec to refresh it.
Best
David
Hello, I've been having this problem for a while and I'm not entirely sure what's causing it or how to re-create it.
Basically exposure between a photo taken in live-view, and then viewed back will be different.
Where something looks totally fine and correctly exposed in Liveview, I'll hit playback and it'll look dark and muddy, almost as if the screen's brightness and contrast have been changed.
I haven't really been testing out what causes it, and I can not confirm whether the photo looks underexposed when viewed on a PC, but I will say this is isolated to ML on 5D3 1.2.3 and it's the March 17 2014 Nighty Build.
This has never happened with my 550D ML, so I'm not sure whether it's a 5D3 issue or a ML for 5D3.
Cheers!
No idea how to reproduce, but post some screenshots from the Expo menu, the Delta menu (modified settings) and a test image from LiveView and QuickReview modes, both with raw histogram enabled.
There is a Canon bug with manual lenses, but that one shows the LiveView much darker than the captured photo (the opposite of what you described).
Hi everybody.
I've just installed ML on my 5D Mark III ( 1.2.3 ). Installation ok. One problem. When I record with mlv module, after starting the recording, the live view just freeze but the recording continue ( I can see the time goes on, number of frame etc... ) I have a CF card Sandisk extreme 32 go 800x... Anybody has a solution ?
Other questions : which is right now the more stable version of ML ( for 1.2.3 ) ?
And what are the better settings to optimize mlv recording ?
Thank you a lot in advance.
how about google "magic lantern cf cards" ?
Quote from: Richardson on May 12, 2014, 04:44:34 PM
Hi everybody.
I've just installed ML on my 5D Mark III ( 1.2.3 ). Installation ok. One problem. When I record with mlv module, after starting the recording, the live view just freeze but the recording continue ( I can see the time goes on, number of frame etc... ) I have a CF card Sandisk extreme 32 go 800x... Anybody has a solution ?
Other questions : which is right now the more stable version of ML ( for 1.2.3 ) ?
And what are the better settings to optimize mlv recording ?
Thank you a lot in advance.
Ok so you think that it comes from my CF card not fast enough... I thought in that case I couldn't record anything or just few seconds... It's just my Liveview freezing and I can anyway play back my recording with mlv player... Thank you for your answer.
Delete ML\Settings\MAGIC.CFG and start over to configure RAW recording. Load MLV_REC.MO *or* RAW_REC.MO, don't use 10x zoom, don't use Global Draw.
Results still the same?
Do you have an USB 3.0 cardreader connected to an USB 3.0 port? In case you have, run a benchmark (ATTO or CrystalDiskMark) and verify your card specifications.
you won't believe me but... After you answered me, I did the whole installation of ML for my 5D Mark III. The same as the last time.
I don't have any MAGIC.CFG in ML/Settings. So don't need to erase.
I first activated the MLV rec module only with global draw off... Liveview no freezing. So perfect.
Then I tried with MLV snd loaded... Liveview no freezing. Perfect.
Loaded Raw rec module ( without unloaded MLV rec and snd )... Liveview no freezing. Perfect.
At the end I don't know what was the problem the first time I installed ML but now it's working great with my CF, and I didn't do anything different... Strange.
The only thing it's the first time I loaded the three modules at the same time. Maybe it's the cause...
By the way do you have settings to optimise the recording ?
Thank you very much for your help :)
Quote from: Richardson on May 13, 2014, 01:13:51 PMThe only thing it's the first time I loaded the three modules at the same time. Maybe it's the cause...
It is. You can reproduce it and it will not work. Same effect like going around a pole left and right at the same time ...
You can not run MLV_REC.MO and RAW_REC.MO at the same time and expect ML working properly. Period.
Ok. Problem solved. Thank you.
Hacked preview was the "problem", that is how it looks like...
Best
David
Exactly what I've just understood. Preview on Auto is ok. Preview on Hacked = liveview freeze.
Please read the first post before continuing the discussion about raw recording.
Locking the thread for 48 hours.
Hi there,
I just had a strange experience with the 5D mk3 and Marek's build. The camera would show the ML menu when I pressed the trash button but switch back after a second. I managed to get all setting dialed in and recorded the set, but it appears the camera wants to negate the WB shift setting in irregular intervals, causing short (luckily slight) colour changes for a fixed number of frames. I'll post two samples in a bit. A few hours after the session the camera (with the same card and all) luckily performed without any problems.
Cheers,
Andrew
Well, took the plunge and installing the latest build of 5D Mark iii 1.2.3 could not have been easier. I installed to a 32GB SanDisk Extreme SDHC card for ML only.
Two quick questions:
1. When shooting raw, what should the picture style be set to? In the past when I shot h.264 I used Technicolor's CineStyle. Does it matter now? I assume nothing is baked in because I am shooting raw... Color Balance, Picture style, etc. Or does it make a difference?
2. Is there a complete manual or PDF floating around that goes over each and every setting? If not has someone started one that I can update and finish?
TIA,
Great work!
1. Doesn't matter.
2. Here (http://www.magiclantern.fm/forum/index.php?topic=11269.0). Feel free to add replies, and I can edit the content as needed.
Just installed 1.2.3 on my Mark III and have had no problems shooting etc. One thing however i've noticed is that when i plug in my HDMI monitor and turn on my camera i do not get my ML. It seems to default to the normal Canon video monitor screen. I was able to access the ML settings by hitting the trash can but that's about it.
thoughts?
J
imported latest build for 5d mIII 1.2.3.
my question is how do you export footage to your computer (i have a mac pro)??
and how do you view in camera??
Quote from: a1ex on May 13, 2014, 05:57:18 PM
Please read the first post before continuing the discussion about raw recording.
Locking the thread for another 48 hours.
Audio meters disappear in nightly build 2014-05-20 15:00:53 -0700. for the 5D Mark iii.
I ran the firmware update to undo the boot flag, restarted the camera and ran the firmware update to the latest build and no more audio meters on the preview screen in Live view in video mode.
Am I missing something?
Quote from: unfilmde on May 21, 2014, 07:15:49 AM
Audio meters disappear in nightly build 2014-05-20 15:00:53 -0700. for the 5D Mark iii.
I ran the firmware update to undo the boot flag, restarted the camera and ran the firmware update to the latest build and no more audio meters on the preview screen in Live view in video mode.
Am I missing something?
Everything's OK for me on 5D mk III
Hello,
For me too, the audiometer work with the 21/05 build
Regards
Quote from: frenchps49 on May 21, 2014, 08:50:43 AM
Everything's OK for me on 5D mk III
Maybe I uninstalled it incorrectly. I ran the firmware update and made the SD card not bootable. Trashed the old files on the card, copied the new files to the card and then ran the firmware update again.
Is there a switch or setting I may have inadvertently turned off?
I can't figure this one out. This is the first time I'm having trouble with a nightly build. The audio meters just don't show up.
Well I narrowed down the audio meter disappearance. If I do a clean install of the latest nightly build 5-20 for the 5D Mark iii they show up. It is when I enable RAW record and setting the frame size to 1920x1080, leaving MLV rec off of course, the audio meters disappear and are replaced with bars, (see picture).
When I turn RAW recording off, they come back again.
This didn't happen in the previous builds.
Audio meters only appear when you are prepared to record some kind of sound (H.264 or mlv_snd). Should be obvious.
Quote from: a1ex on May 21, 2014, 07:42:38 PM
Audio meters only appear when you are prepared to record some kind of sound (H.264 or mlv_snd). Should be obvious.
A1ex, it should be obvious, but they were there in the last build with the settings I had when set to RAW record. I understand it should be obvious. I was just curious why they went away. You can't record RAW and have MLV_SND on or you enter an ERR loop.
I prefer to shoot RAW as MLV_Raw my one day disappear and so go the files.
Quote from: Fioritura on May 16, 2014, 12:44:04 PM
I just had a strange experience with the 5D mk3 and Marek's build. The camera would show the ML menu when I pressed the trash button but switch back after a second. I managed to get all setting dialed in and recorded the set, but it appears the camera wants to negate the WB shift setting in irregular intervals, causing short (luckily slight) colour changes for a fixed number of frames. I'll post two samples in a bit. A few hours after the session the camera (with the same card and all) luckily performed without any problems.
Here are two samples.
Cheers,
Andrew
https://drive.google.com/file/d/0B23tS9bIjRt6ZjhfbkVLT0pqTDQ/edit?usp=sharing (https://drive.google.com/file/d/0B23tS9bIjRt6ZjhfbkVLT0pqTDQ/edit?usp=sharing)
https://drive.google.com/file/d/0B23tS9bIjRt6NlAzWEw3UWxxcEU/edit?usp=sharing (https://drive.google.com/file/d/0B23tS9bIjRt6NlAzWEw3UWxxcEU/edit?usp=sharing)
Re-post because i think it got lost in the mix and i'd love anybody's thoughts on what's going on here.
Just installed 1.2.3 on my Mark III and have had no problems shooting etc. One thing however i've noticed is that when i plug in my HDMI monitor and turn on my camera i do not get my ML. It seems to default to the normal Canon video monitor screen. I was able to access the ML settings by hitting the trash can but that's about it. When I go ahead and turn off mirroring on the canon menu then ML appears on the monitor however i thought that with 1.2.3 you were able to get mirroring.
thoughts?
Hi Guys....great stuff going on with ML but i am wondering if there is a way to have the ML firmware on a single card that will work on both 5d mk 3 and mk 2?? Is it possible rather than having lots of expensive cards for each? :(
can you try it and let us know how it works? good luck!
Quote from: rick_ford55 on May 21, 2014, 10:37:54 PM
Hi Guys....great stuff going on with ML but i am wondering if there is a way to have the ML firmware on a single card that will work on both 5d mk 3 and mk 2?? Is it possible rather than having lots of expensive cards for each? :(
Quote from: jrcreative on May 21, 2014, 10:30:41 PM
Re-post because i think it got lost in the mix and i'd love anybody's thoughts on what's going on here.
Just installed 1.2.3 on my Mark III and have had no problems shooting etc. One thing however i've noticed is that when i plug in my HDMI monitor and turn on my camera i do not get my ML. It seems to default to the normal Canon video monitor screen. I was able to access the ML settings by hitting the trash can but that's about it. When I go ahead and turn off mirroring on the canon menu then ML appears on the monitor however i thought that with 1.2.3 you were able to get mirroring.
thoughts?
Didn't get lost. Read the thread.
Quote from: rick_ford55 on May 21, 2014, 10:37:54 PM
Hi Guys....great stuff going on with ML but i am wondering if there is a way to have the ML firmware on a single card that will work on both 5d mk 3 and mk 2?? Is it possible rather than having lots of expensive cards for each? :(
I would not do that. I would rather fork out 200 bucks rather than brick a body!
Quote from: rpt on May 22, 2014, 03:38:31 AM
I would not do that. I would rather fork out 200 bucks rather than brick a body!
If you have two cameras, why do you intend modify the firmware for the people like me with only one? ;)
Use SD card for ML, are very cheap.
Why 200..? Buy 2 cheap sd - one for mk2 and one for mk3. put ml on each card and leave them in your cameras.. So you only have to change the much more important and faster cf card.
Quote from: swinxx on May 22, 2014, 10:58:16 AM
Why 200..? Buy 2 cheap sd - one for mk2 and one for mk3. put ml on each card and leave them in your cameras.. So you only have to change the much more important and faster cf card.
the mkii doesn't have any sd-card-slot.
We have 40 fps in 1080p RAW, test it out!
Other frame rate limits: 38 fps in 1080p H.264, and 67fps in 720p, both RAW and H.264.
Technical info here (http://www.magiclantern.fm/forum/index.php?topic=11965).
Tests needed:
- push FPS to the maximum values and make sure you can record safely in RAW, MLV and H.264. If there are artifacts, that's a bug.
- try all the video modes (1080p, 720p, 480p, zoom, photo...)
- write down what you have tested, so others would be able to focus on untested modes.
The update will be also in 5D3.113, and it's been already there in 60D, 600D and 1100D for ages (with some lower FPS limits).
Quote from: a1ex on May 22, 2014, 10:06:33 PM
We have 40 fps in 1080p RAW, test it out!
Other frame rate limits: 38 fps in 1080p H.264, and 67fps in 720p, both RAW and H.264.
Technical info here (http://www.magiclantern.fm/forum/index.php?topic=11965).
Tests needed:
- push FPS to the maximum values and make sure you can record safely in RAW, MLV and H.264. If there are artifacts, that's a bug.
- try all the video modes (1080p, 720p, 480p, zoom, photo...)
- write down what you have tested, so others would be able to focus on untested modes.
The update will be also in 5D3.113, and it's been already there in 60D, 600D and 1100D for ages (with some lower FPS limits).
Great work A1ex!!!! As always!
Do you know a link, or a way to reduce the black noise in RAW?
Any recommendations?
:)
Quote from: a1ex on May 13, 2014, 05:57:18 PM
Please read the first post before continuing the discussion about raw recording.
Locking the thread for 48 hours.
Using magiclantern-Nightly.2014May22.5D3123
The ETTR function does not work correctly(OVEREXPOSED)
Works here. Steps to reproduce?
OK I have it checked deeper and it occurs (in Still photography),
only when I have the fps activated(in video mode 25p->25p)
Using magiclantern-Nightly.2014May22.5D3123
modules loaded:
ETTR
ML_REC
ML_SOUND
ML_PLAY
Stopped at about 4 sec after recording...
"Early stop(9)...Didn't make it to estimated recording time!"
FPS Override
Desired FPS: 40 (from 24)
Optimized for: EXACT FPS
Actual FPS: 40.000
Komputerbay 64gb 1000x
firmware 1.1.3
Sorry if writing in the wrong thread or in another form inadequate.
38 fps in H.264 is great! Any chance adding sound, maybe in an extra file or so as a backup if needing sound for some reason and going back from 38 to 25 fps? I would appreciate this as another killer feature for my wedding documentary work...
Or did I miss something?
THX! :)
Quote from: gideonplus on May 23, 2014, 12:28:54 PM
OK I have it checked deeper and it occurs (in Still photography),
only when I have the fps activated(in video mode 25p->25p)
Fixed, thanks.
Quote from: magic4001 on May 23, 2014, 05:53:07 PM
38 fps in H.264 is great! Any chance adding sound, maybe in an extra file or so as a backup [...]
There was an option to record a separate WAV file. Will be likely added back once the new-sound-system (https://bitbucket.org/hudson/magic-lantern/commits/branch/new-sound-system) branch will be ready.
Yeah! Hugs! :D
Quote from: Untitledphoto on May 23, 2014, 12:44:27 PM
Stopped at about 4 sec after recording...
"Early stop(9)...Didn't make it to estimated recording time!"
FPS Override
Desired FPS: 40 (from 24)
Optimized for: EXACT FPS
Actual FPS: 40.000
Komputerbay 64gb 1000x
firmware 1.1.3
Installed 1.2.3 firmware... but same thing (3-4 seg and stops).
I can barely get 3 seconds at 40fps 1920x1080.
There is a bug if you use memory hack: it records at 38 fps. I'm surprised nobody noticed it.
Also, just noticed that if you record on CF, you are more likely to get dropped or corrupted frames (in both raw and h.264). Yesterday I did all my tests on a SD card, and it seems a better choice when pushing FPS to the maximum value.
Can you confirm?
Quote from: a1ex on May 23, 2014, 09:04:31 PM
I can barely get 3 seconds at 40fps 1920x1080.
There is a bug if you use memory hack: it records at 38 fps. I'm surprised nobody noticed it.
So, everything is in its place :)...
It's supposed to be that way
Thank you sir.
(i'm not using memory hack)
Quote from: a1ex on May 23, 2014, 09:04:31 PM
Also, just noticed that if you record on CF, you are more likely to get dropped or corrupted frames (in both raw and h.264). Yesterday I did all my tests on a SD card, and it seems a better choice when pushing FPS to the maximum value.
I thought only CF cards had the necessary write speed. Is that not so?
Cheers,
Andrew
Quote from: a1ex on May 23, 2014, 09:04:31 PM
...
Also, just noticed that if you record on CF, you are more likely to get dropped or corrupted frames (in both raw and h.264). Yesterday I did all my tests on a SD card, and it seems a better choice when pushing FPS to the maximum value.
Can you confirm?
Sorry, don't have a good speedy SD card ! :-\
Hi there, I've been running a nightly build of ml 1.2.3 on my 5d since April 20th. Today I noticed that I was getting a lot of horrible crackling in my audio, I use a rode video mic pro. Interestingly the internal mic on the 5d doesn't get any crackling, only when I use the jack plug (even when the mic is turned off). I've tested different external mics and still have the same issue. Tested my mics on different cameras and they work fine. I tried taking ml off my camera and the problem was still there :/ also tried the most up to date version of ml but no good... Everything else works fine.
Just a note I think the nightly build I had installed was from 16th April.
Quote from: Fioritura on May 23, 2014, 09:27:58 PM
I thought only CF cards had the necessary write speed. Is that not so?
I was talking about corrupted and dropped frames, not about write speed.
a1ex,
thanks for the great work!
I tried 1.2.3 with great success!
just wanted to tell you the anamorphic stretch doesn't work in the HDMI output (not in mirrored, in normal "single screen")
If you need some test I can try to help! ;)
Alex,
Have just tried this 24 may Nightly Build (for 1.1.3).
Got max 3-4 seconds in 1080p MLV at 40FPS (exact FPS) with Komputerbay 1000x 64GB. Nevertheless, I've got approx. 50% "corrupted" files (which I have not with same setting execpt 30FPS). Three different patterns (first one is one of the 50% working dng):
(http://www.casimages.com/img.php?i=140524011126776625.jpg)
(http://www.casimages.com/img.php?i=140524011244988764.jpg)
(http://www.casimages.com/img.php?i=140524011317100571.jpg)
(http://www.casimages.com/img.php?i=1405240113356100.jpg)
Extracted with MLVBrowseSharp from g3gg0 (but same "looking" results with MLV viewer on 5D3).
Same results with or without memory hacks, or with any of preview modes (by the way, is it normal I have a preview of what I film with hacked
2 preview mode?)
If I can test anything else, don't hesitate,
Simon
See my post above. If you record on SD, you should not get these artifacts.
Also, if you have some slower CF cards, try to see if it helps.
I'll run some tests and recalibrate the max limits, most likely taking into account the selected card.
Hi there,
I'm on 5D MARK III 1.2.3
I've test the 40 fps both on slower CF and SD card but I still got drop frames on H264 . Considerably less then when I'm using a 1000x cf card but still there. Instead on MLV Raw i get 3-4 sec on on Lexar 32GB 1000X and 2-3 sec on Komputerbay 128GB 1000x with a lot of artefacts.
Alex do you have 100% drop free clips when using a slow sd?
Am I the only one playing Arkonoid all the time instead of testing the software??? :o
Thanks for the nice work anyhow. Very nice software again.
Maybe a dumb question cause i don't really get this...I was testing the "timelapse through FPS override" scenario (ex. 0.25 fps) but this is the opposite. Are you trying to set FPS override to 40 fps while in Canon menu the video ia set at 24 or 30 fps...What's the meaning of 40 fps in this scenario? I don't doubt anything, maybe it's just my ignorance concerning FPS override. Can anyone explain the goal?
Quote from: a1ex on May 22, 2014, 10:06:33 PM
We have 40 fps in 1080p RAW, test it out!
Other frame rate limits: 38 fps in 1080p H.264, and 67fps in 720p, both RAW and H.264.
Technical info here (http://www.magiclantern.fm/forum/index.php?topic=11965).
Tests needed:
- push FPS to the maximum values and make sure you can record safely in RAW, MLV and H.264. If there are artifacts, that's a bug.
- try all the video modes (1080p, 720p, 480p, zoom, photo...)
- write down what you have tested, so others would be able to focus on untested modes.
The update will be also in 5D3.113, and it's been already there in 60D, 600D and 1100D for ages (with some lower FPS limits).
Hi Alex,
What
exact memory card did you use for this (especially for RAW video)?
Thank you!
05-23 (1.2.3) - 40fps 1080p - lexar 800x 64
was able to get 47 frames (9 of them corrupted), memory hack OFF
Hi guys, I'm wondering how to move the ML to another sd card. I've tried to format a new SD card and then unpack ML to that but then I put the new card in the camera the ML does not works. It seems that ML is tied to the sd card I installed ML from.
Please any suggestions.
The card needs to be made bootable by setting the bootflag with EOSCard before ML will run...
Or run firmware update again using this card.
Steda, how can i sett boot flag on the new card?
Walter, can i just run update without any problem on my 5dm3 when ML is already installed?
Quote from: Stedda on May 26, 2014, 05:06:24 PM
by setting the bootflag with EOSCard
Or like Walter said... either way works.
Quote from: a1ex on May 22, 2014, 10:06:33 PM
We have 40 fps in 1080p RAW, test it out!
Tests needed:
- push FPS to the maximum values and make sure you can record safely in RAW, MLV and H.264. If there are artifacts, that's a bug.
- try all the video modes (1080p, 720p, 480p, zoom, photo...)
Tried it out very quickly with the latest Nightly, 1080p h264 seems to work at max fps so far, camera movement (panning) results in freeze frames.
Thanks for unlocking yet another marvelous possibility!
Quote from: RowanMachine on May 23, 2014, 09:49:49 PM
Hi there, I've been running a nightly build of ml 1.2.3 on my 5d since April 20th. Today I noticed that I was getting a lot of horrible crackling in my audio, I use a rode video mic pro. Interestingly the internal mic on the 5d doesn't get any crackling, only when I use the jack plug (even when the mic is turned off). I've tested different external mics and still have the same issue. Tested my mics on different cameras and they work fine. I tried taking ml off my camera and the problem was still there :/ also tried the most up to date version of ml but no good... Everything else works fine.
Just a note I think the nightly build I had installed was from 16th April.
This is very worrying, any others with this problem? And or a solution?
preamp distorsion? are you sure it's not the microphones own pre-amp causing the distortion? +20 dB setting can easily cause this.
Man it's sound like you might have something loose in your camera and it not grounding properly. I have a similar issue when I use a recorder and I use a cheap USB adapter to power it. I get a lot of noise in the camera out and line out.
Can you choose to boot into the original Canon 1.2.3 firmware after installing ML?
Can you go back and forth between them?
thx, looking forward to trying this out!
Quote from: Steve_Brule on May 27, 2014, 02:05:09 PM
Can you choose to boot into the original Canon 1.2.3 firmware after installing ML?
Can you go back and forth between them?
thx, looking forward to trying this out!
Press SET while camera is turning on...
Hi guys,
I want the use focus peaking and wonder what I have to enable? I have enabled focus peaking, but can not see anything on my live view display.
Quote from: jarandov on May 27, 2014, 04:31:21 PM
Hi guys,
I want the use focus peaking and wonder what I have to enable? I have enabled focus peaking, but can not see anything on my live view display.
Global Draw
@jarandov: About time to look into FAQ and User Guide:
http://wiki.magiclantern.fm/userguide#overlay
Guys I really really need your help. I must be missing some vital step but I've been over the instal procedure at least a dozen times and my camera just won't read the files. her's what I've done. Format card, download ML files 1.2.3 Put files on card. Put card in camera. switched on camera. Then nothing. Went to firmware up date. pressed firmware update. camera says you'll need a memory card to update I press Ok then nothing. 12 times I've done this and still nothing. What should the ML files look like? I've gone to the link on this page and copied those files which says ML nightly. Are these ally he files I need cause sit doesn't look like it to me. Need your help. Some guy tried to charge me £120 for the privilege of installing Magic Lantern and I'm getting rather frazzled.
Quote from: Stedda on May 27, 2014, 04:32:58 PM
Hi guys,
I want the use focus peaking and wonder what I have to enable? I have enabled focus peaking, but can not see anything on my live view display.
If you want to see the dots appear around the areas that are in focus, you will need to press the INFO button until you are getting the ML display. Otherwise, focus peaking will not appear. It took me a while to figure this out.
Sorry, looking for some clarity on the FPS override and CF/SD card issue:
Alex, are you saying that the ~40fps recording (MLV & H.264) gives less corrupted frames if using SD card? Like someone mentioned, are there any SD card that are even fast enough for MLV recording at 40fps? Am I misunderstanding something here?
Quote from: davidc on May 27, 2014, 05:48:39 PM
Guys I really really need your help. I must be missing some vital step but I've been over the instal procedure at least a dozen times and my camera just won't read the files. her's what I've done. Format card, download ML files 1.2.3 Put files on card. Put card in camera. switched on camera. Then nothing. Went to firmware up date. pressed firmware update. camera says you'll need a memory card to update I press Ok then nothing. 12 times I've done this and still nothing. What should the ML files look like? I've gone to the link on this page and copied those files which says ML nightly. Are these ally he files I need cause sit doesn't look like it to me. Need your help. Some guy tried to charge me £120 for the privilege of installing Magic Lantern and I'm getting rather frazzled.
Sounds like you have an issue which isn't directly related to ML & FW 1.2.3. but potentially something wrong with the camera and/or card if the camera doesn't recognise your card.
Could it be that you have the wrong card slot selected (CF/SD) in Canon menus? Can someone tell if this actually is possible or does the camera check both slots for cards/firmware?
If you can't do it yourself you have to pay somebody who can. I'm just curious why you tried 12 times if you saw it would not work after 2 or 3 attempts ?
Did you try another SF cards, did you check all the setting ?
You remind me one woman from the past, when she couldn't get something to work she would try the same way again and again until she gets absolutely insane and slapped her husband on the face :)
Quote from: davidc on May 27, 2014, 05:48:39 PM
Guys I really really need your help. I must be missing some vital step but I've been over the instal procedure at least a dozen times and my camera just won't read the files. her's what I've done. Format card, download ML files 1.2.3 Put files on card. Put card in camera. switched on camera. Then nothing. Went to firmware up date. pressed firmware update. camera says you'll need a memory card to update I press Ok then nothing. 12 times I've done this and still nothing. What should the ML files look like? I've gone to the link on this page and copied those files which says ML nightly. Are these ally he files I need cause sit doesn't look like it to me. Need your help. Some guy tried to charge me £120 for the privilege of installing Magic Lantern and I'm getting rather frazzled.
Quote from: davidc on May 27, 2014, 05:48:39 PM
Guys I really really need your help. I must be missing some vital step but I've been over the instal procedure at least a dozen times and my camera just won't read the files. her's what I've done. Format card, download ML files 1.2.3 Put files on card. Put card in camera. switched on camera. Then nothing. Went to firmware up date. pressed firmware update. camera says you'll need a memory card to update I press Ok then nothing. 12 times I've done this and still nothing. What should the ML files look like? I've gone to the link on this page and copied those files which says ML nightly. Are these ally he files I need cause sit doesn't look like it to me. Need your help. Some guy tried to charge me £120 for the privilege of installing Magic Lantern and I'm getting rather frazzled.
Have you tried pressing the Trashcan Button after the camera starts up.................................????????
Quote from: davidc on May 27, 2014, 05:48:39 PM
Guys I really really need your help.
Format card using your cardreader. Insert card into cam. Format again. Put back into cardreader.
Expand nightlies content to card. You must have
ML directory
autoexec.bin
ML5D3123.FIR
on your card. Insert card into cam and run firmware update. Follow instruction. If you let timeout (30 seconds after successful installation) pass ML will deinstall itself. If you see the counter running down you have to turn off the cam. Restart, wait a while and press trashcan button.
Results?
Do you already updated the Canon firmware to 1.2.3 ??? ML files 1.2.3 works only with Canon firmware 1.2.3
Quote from: davidc on May 27, 2014, 05:48:39 PM
Guys I really really need your help. I must be missing some vital step but I've been over the instal procedure at least a dozen times and my camera just won't read the files. her's what I've done. Format card, download ML files 1.2.3 Put files on card. Put card in camera. switched on camera. Then nothing. Went to firmware up date. pressed firmware update. camera says you'll need a memory card to update I press Ok then nothing. 12 times I've done this and still nothing. What should the ML files look like? I've gone to the link on this page and copied those files which says ML nightly. Are these ally he files I need cause sit doesn't look like it to me. Need your help. Some guy tried to charge me £120 for the privilege of installing Magic Lantern and I'm getting rather frazzled.
Quote from: Stedda on May 27, 2014, 02:07:54 PM
Press SET while camera is turning on...
Thanks Stedda! I presume that pressing SET during boot will land you in the Original Canon 1.2.3 firmware?
Hi guys, I believe I downloaded ML to my M3 but when I go into the ML menu under video mode I don't see a Raw Video option, am I doing something wrong. Thanks.
You may want to read FAQ, User Guide and load RAW_REC.MO or MLV_REC.MO from Modules tab.
Thanks a lot I'll go check that out.
So I've been through all of FAQ and maybe I'm just missing it somewhere but I can't find information on how to load the Modules Tab to enable Raw, my ML menu has a triangle instead of an M, any help would be appreciated.
Thanks
Browse tabs. One is labeled Modules.
Thanks Walter I found it and got it to load, one more question if you might be able to help, when I hit record it only records for a second then I get and error message "Early Stop (9). Didn't make it to estimated record time" I'm using an SD card class 10 with 90mb/s, is there something else I need to do?
Bad news: SD card interface in 5D3 is limited to ca. 21 MByte/s and there is nothing you can do about it.
You need a fast CF-card for RAW/MLV at high resolution. Do a search here and decide which one you want to purchase.
EDIT: 90 mb/s = 11,25 MByte/s?
Thanks I'll look it up.
No more updates, until you guys will understand that raw video should be discussed in this area (http://www.magiclantern.fm/forum/index.php?board=49.0) and not here.
;)
Quote from: a1ex on May 28, 2014, 11:02:25 PM
No more updates, until you guys will understand that raw video should be discussed in this area (http://www.magiclantern.fm/forum/index.php?board=49.0) and not here.
;)
omgosh what will i do the rest of my life =( thanks guys!
Sounds like the Soup Nazi :)
Amazing news,
does this firmware still allow the normal raw_rec module? i have no interest in mlv but i am very excited about the bootflag thing finally being fixed
Redaber, no more magic for you!
Hi,
Used ML for quite some time on my EOS-M and I fell in love with the video crop mode. Just installed the latest nightly build on my 5d3. All seems well, but I can't find crop mode. Camera is in video mode, I even tried loading raw_rec and mlv_raw, still no crop mode.
Searched the forums but I must have missed where this was addressed. Any help would be appreciated.
Edit: not RAW cropped mode, just plain old h.264
LAZY A$$
http://www.magiclantern.fm/forum/index.php?topic=5441.0
Quote from: The Monitor Lizard on May 30, 2014, 01:13:45 AM
Hi,
Used ML for quite some time on my EOS-M and I fell in love with the video crop mode. Just installed the latest nightly build on my 5d3. All seems well, but I can't find crop mode. Camera is in video mode, I even tried loading raw_rec and mlv_raw, still no crop mode.
Searched the forums but I must have missed where this was addressed. Any help would be appreciated.
Just wanted to add after playing around with Nightly build 5-23-2014 on my 5D Mark iii....
WOW!!!
I underexposed a lot on purpose. ISO 640 (my test show this to be native with my camera). Shot under tungsten lighting. I was able to bring back the image and remove the warm cast and the image was beautiful.
My 2¢
Quote from: The Monitor Lizard on May 30, 2014, 01:13:45 AM
Hi,
Used ML for quite some time on my EOS-M and I fell in love with the video crop mode. Just installed the latest nightly build on my 5d3. All seems well, but I can't find crop mode. Camera is in video mode, I even tried loading raw_rec and mlv_raw, still no crop mode.
Searched the forums but I must have missed where this was addressed. Any help would be appreciated.
Edit: not RAW cropped mode, just plain old h.264
I'm interested in h.264 crop too. I'm a little hesitant to ask questions here, cause, although I'm really excited to try ML, I'm a complete newbie. My needs are pretty simple: focus aids and video crop mode. For everything else I'm fine with the Canon 1.2.3 .... although that will probably change
I'd like to verify how to upgrade from ML 1.1.3 to 1.2.3. I know it has been answered here and there on this forum but I'd like to confirm to avoid some problems. Thank you for understanding and patience (I'm just one of those guys who freak out sometimes... well, very often as a matter of fact).
My understanding is the following one:
1. Take out an SD card with ML 1.1.3. (at least I keep ML on an SD card)
2. Put a new SD card with Canon firmware 1.2.3 and do upgrade.
3. Format another SD card in camera.
4. Copy ML nightly build of your choice on the formatted card from 3.
5. Put the card in the camera and do ML upgrade.
Is this correct?
Also, once I do uninstall of ML 1.2.3 as Alex described in the first thread of this post it will leave camera without ML trace. Is this correct?
Thank you so much for your patience and time!
Please read the post and try the ML on your 5dIII at your own risk like everybody else here. If you freak out - use the factory setting or buy RED. Sorry about harsh words but this topic has been discussed a million times. Have some respect.
Quote from: dag on May 30, 2014, 04:30:53 AM
I'd like to verify how to upgrade from ML 1.1.3 to 1.2.3. I know it has been answered here and there on this forum but I'd like to confirm to avoid some problems. Thank you for understanding and patience (I'm just one of those guys who freak out sometimes... well, very often as a matter of fact).
My understanding is the following one:
1. Take out an SD card with ML 1.1.3. (at least I keep ML on an SD card)
2. Put a new SD card with Canon firmware 1.2.3 and do upgrade.
3. Format another SD card in camera.
4. Copy ML nightly build of your choice on the formatted card from 3.
5. Put the card in the camera and do ML upgrade.
Is this correct?
Also, once I do uninstall of ML 1.2.3 as Alex described in the first thread of this post it will leave camera without ML trace. Is this correct?
Thank you so much for your patience and time!
Quote from: vovkinson on May 30, 2014, 04:40:30 AM
Please read the post and try the ML on your 5dIII at your own risk like everybody else here. If you freak out - use the factory setting or buy RED. Sorry about harsh words but this topic has been discussed a million times. Have some respect.
I do have lots of respect for ML lantern and I've been running one on my 5D MK III since the first 1.1.3 came out. Anyway, thank you very much for your informative answer.
Quote from: The Monitor Lizard on May 30, 2014, 01:13:45 AM
Edit: not RAW cropped mode, just plain old h.264
For this, I'm afraid you have to upgrade to a 550D or 600D :P
Where can I find "bulb ramping"?In Shoot-intervalometer I can"t find it
http://www.magiclantern.fm/forum/index.php?topic=11108.msg117332;topicseen#msg117332
Hi,
Firstly thank you so much for this incredible gift that is opening up an already great camera. I really am impressed!
I use Manual White Balance a lot when shooting and need to be able to adjust it as quickly as possible. I have found the route that gives a fairly fast adjustment here:
Set WB to Manual using WB button on camera
With the camera in Liveview access ML menu Expo/White Balance/press Q/Auto adjust Kelvin and G/M.
Is there any way to shorten this so that a single button push will fast track through this process?
Many thanks
Richard
Don't have a One-Click-Solution but some kind of shortcut:
Use Prefs tab -> "Customize Menus" and choose Auto Adjust. It will be available via MyMenu tab.
One-click solution by pressing RATE ;)
(you may need to disable arrow shortcuts in Prefs menu, or just tweak them)
I use rate all the time, an impressive time saver! Thx
Thank you!
Quote from: marekk on May 01, 2014, 02:45:11 PM
Fresh compiled version of ML with overlays on LCD (mirroring enabled):
https://www.dropbox.com/s/8ejsn7zn6eh1sdp/5D3_hdmi.zip
USE IT FOR TESTS ONLY AND ON YOUR OWN RISK
Thank you so much for this...this is the the answer to my prayers.
I really hope that it will find it's way into future 1.2.3 builds soon.
My only other remaining magic lantern prayer is to have REC_KEY enabled on 5D3 1.2.3 build - so I can trigger video record from an external trigger switch via half shutter command.
Is there a technical reason why it is the only camera to not have this function enabled?
Regards!
1) ask Marekk to submit a patch
2) it's in Canon menu, why duplicate it in ML menu?
Quote from: a1ex on June 03, 2014, 10:46:11 AM
1) ask Marekk to submit a patch
2) it's in Canon menu, why duplicate it in ML menu?
1= Will do
2= Canon menu trigger can start movie record on full press of shutter button only, not half press.
Sounds insignificant but half shutter would allow a very simple DIY external trigger button to be made for anyone wanting to make their own wired record button extension - without having to find a bulky two-stage switch that is basically impossible to find in a very small form factor. It would also simplify many triggering options for anyone making their own remote control camera rigs, controlled via Arduino etc. (for cranes/jibs/etc).
Cheers for the reply a1ex :)
2. Just tried shorting the shutter and the ground pin, and it started recording. Am I missing something?
Quote from: a1ex on June 03, 2014, 11:34:04 AM
2. Just tried shorting the shutter and the ground pin, and it started recording. Am I missing something?
Correct, but stopping record requires all pins to connect - requiring a two-stage switch I think.
I made a simple button trigger for the shutter and ground pin (or other pin) and it worked a dream on my 7D with the half shutter REC_key function. On press start, one press stop.
I (and I hope many others) will find it enormously helpful to have this function on 5D3 1.2.3 for remote record triggering.
Cheers a1ex (again!)
Stopping works fine for H.264, but for RAW it seems unreliable. I'd rather try to fix that instead of adding YAMLMO (http://www.magiclantern.fm/forum/index.php?action=search2&search=yamlmo&show_complete=1).
Understood :)
Many thanks for investigating
I made a trigger that works fine with ML raw too. I used a transistor that provided some sort of delay for the 2nd wire. First the AF has to triggered then the shutter release too, then they have to be released both in order to have camera controll. To stop the recording, same thing.
It happens to work work for me after some experiments. Without the transistor it is not reliable at all.
I updated from 1.1.3 ML to 1.2.3 ML without problems.
I followed the instructions by simply removing the ML card, adding canon firmware on another card, updating, then inserting the 1.2.3 ML version. Awesome work people.
Question for a1ex: is there a reason to stay on 1.1.3 firmware for ML? Are there some 1.2.3 limitations? Lost speed? Still more bugs to trace than in 1.1.3? Anything to know?
Thanks,
S.
Quote from: a1ex on March 16, 2014, 03:26:45 PM
What's hot:
- bootflag issue solved! (p.s. some bloggers got it wrong, you still enable it in the camera, but you can disable it by uninstalling)
- installation is really easy (simply unzip the files on the card, update firmware and you are ready to go)
- uninstallation is equally easy (update firmware and follow the instructions)
- EosCard is now optional
- ML restores itself after formatting the card (man, that komputerbay card is fast!)
- you may install on any card combination you may think of.
What's not:
- unlike most firmware updates which fix minor things, this one changed a LOT, especially on the display side (for example, LiveView is now quad-buffered and most of the display registers were changed).
- watch out for corrupted frames (http://www.magiclantern.fm/forum/index.php?topic=10443) (from my limited testing, I'm not fully convinced the issue is fully resolved on 1.2.3 => for serious video use, please consider staying on 1.1.3)
- fast zebras not working, but can be fixed
- no full-screen magic zoom (I never used it anyway, but was nice)
- no brightness/contrast/saturation adjutments (registers changed)
- HDMI issues (possibly worse than 113, didn't try yet)
- no documentation (yet).
For photo use (raw overlays, ETTR and so on) it should be just fine (that's how I use it).
k, thanks I will stay with 1.1.3 for the moment.
This forum is so huge it is difficult to trace the good informations.
S.
Yes, that's why we try and keep the original posts updated. :)
Yesterday I finished shooting for a promotional video in RAW. I've been able to use liveview mirroring with minor issues (sometimes I had to turn off/on to get the image on the other 2nd monitor).
Sometimes I had the just the ML menu black background and the overlays instead of the liveview image (pressing ML menu button twice fix it). Sometimes REC button do nothing, and there's always a 1/2 seconds span between pressing the button and actual recording.
Overall I've to say I feel this release really stable. I shoot 4 hours in these days with no corrupted files/frames.
I'll post this video in the showcasing forum =)
Thank you guys
Edit:
I used marekk solution for mirroring related issues.
Quote from: marekk on May 01, 2014, 02:45:11 PM
Fresh compiled version of ML with overlays on LCD (mirroring enabled):
https://www.dropbox.com/s/8ejsn7zn6eh1sdp/5D3_hdmi.zip
USE IT FOR TESTS ONLY AND ON YOUR OWN RISK
thank you too :D
Quote from: a1ex on March 16, 2014, 03:26:45 PM
[...]
- watch out for corrupted frames (http://www.magiclantern.fm/forum/index.php?topic=10443) (from my limited testing, I'm not fully convinced the issue is fully resolved on 1.2.3 => for serious video use, please consider staying on 1.1.3)
[...]
Since my camera came with 1.2.3 installed the question is if I should revert to 1.1.3. Does "serious video use" pertain mainly to using the raw functionality or to video recording in general? For me H.264 recording seems to work fine except for a one-off issue. Are most people using the older firmware?
Regards,
Andrew
Quote from: Fioritura on June 06, 2014, 09:45:37 PM
Are most people using the older firmware?
I don't shoot video. Only stills. I am on 1.2.3.
Hi, I came across the rack focus part of the menu and have been trying to get it to work for me with very limited success. Sometimes the camera will do what I want, i.e pull focus fro start point to end point but not always....but above all I am unable to get the camera to record anything whilst it's doing that.
What am I missing?
Please help as this is a really nice feature and I'd love to be able to incorporate it into my films.
Richard
I moved today to the latest build of May 23, 2014 (deleted an old ML from SD card, and copied the content of ZIP to SD card, so no old setting persisted)
I am getting a strange preview following a shot.
https://picasaweb.google.com/116039908015319550699/V5d3#6022695873692450594 (https://picasaweb.google.com/116039908015319550699/V5d3#6022695873692450594)
It is sometimes on the pink background. The histogram I am using is RAW HistoBar (not the Full Histogram that actuall appears at the preview)
Am I doing somehing wrong?
Thanks | P
Rack focus: the easiest way is to mix it to follow focus: http://wiki.magiclantern.fm/userguide#follow_focus
Quote
Quick rack focus while recording:
* Press MENU to save current focus point (this means I want to return here);
* Use follow focus to change focus point (focus somewhere else);
* Press PLAY to go to saved focus point;
* Press PLAY again to go back.
The classic way works too. Set up the focus range offline, start recording, get back into menu and start rack focus. Or, while recording, just press PLAY.
Histogram: this is the YUV histogram, not the RAW one. If you have the picture quality set to RAW, and you are in QuickReview mode (right after taking a picture, not in regular playback mode), you need to describe the steps to reproduce it. Also check Canon settings to get a larger preview.
Already answered.
And triple-posting is not welcome on this forum, FYI.
Updating to 1.2.3 . Everything was successfully done, but rite now i don't have RAW recording position in ML menu. What's wrong?
Quote from: AlexZapp on June 10, 2014, 01:08:27 PM
What's wrong?
Nothing. You have to load RAW_REC.MO or MLV_REC.MO first.
Thanks Alex I'll give it a go.
Quote from: rigs on April 18, 2014, 03:32:11 PM
@mixmastermike
Could you please tell which build worked for HDMI trigger and MLV raw recording. I want to use it with my Ninja but haven't any luck with the latest build.
QuoteIn last weeks build the HDMI trigger was working too, so that when you pressed record on the ninja blade, it triggered the 5D MKiii to start recording Raw.
I would like to know about this as well. It would be a huge help. Thank you for all your hard work.
Hi, I'm new to ML. Can anyone tell me, if this latest release and the *stable* version 1.1.3 solve the problem of canons 30min recording limit on the 5d mk iii (when recording in the standard codec, not raw)?
Thanks for reply!
Thomy
Quote from: thomy on June 11, 2014, 09:50:12 AM
Hi, I'm new to ML. Can anyone tell me, if this latest release and the *stable* version 1.1.3 solve the problem of canons 30min recording limit on the 5d mk iii (when recording in the standard codec, not raw)?
Thanks for reply!
Thomy
Hi Thomy, 29:59 it's the limit. You can set in ML menu Movie Restart and lost just a few seconds.
In H264 4GB it's the limit too.
Take a look in the guide! http://wiki.magiclantern.fm/userguide
Apologies if this has been answered previously.
In the current 5D3-123 source the backup_task (boot_hack.c) and dump_rom_task (debug.c) code both dump two 16MB regions from 0xF0000000 (ROM0.BIN) and 0xF8000000 (ROM1.BIN).
When I look at these they are both empty (filled with 0xFF).
When I checked the ROMBASEADDR for the camera is shows as 0xFF0C0000.
Shouldn't one of the dumps be starting at 0xFF000000?
I finally managed to compile from the source and when I changed ROM0.BIN to dump from 0xFF000000 I get something that looks more like a Canom firmware dump.
Thanks,
Phil.
Hey, CHDK guys are always welcome ;)
g3gg0 explains it here: http://www.magiclantern.fm/forum/index.php?topic=6785.msg58899#msg58899
It may be helpful to load these dumps in QEMU: http://www.magiclantern.fm/forum/index.php?topic=2864
(basically you need to get the "gaonisoy" part at 0xFF0C0000; the QEMU log will tell you a bit more about where each ROM is mirrored)
Quote from: a1ex on June 11, 2014, 03:17:30 PM
Hey, CHDK guys are always welcome ;)
g3gg0 explains it here: http://www.magiclantern.fm/forum/index.php?topic=6785.msg58899#msg58899
It may be helpful to load these dumps in QEMU: http://www.magiclantern.fm/forum/index.php?topic=2864
(basically you need to get the "gaonisoy" part at 0xFF0C0000; the QEMU log will tell you a bit more about where each ROM is mirrored)
Thanks, seems to be working now. Must not have looked closely enough at the original dumps - they're a bit different to the P&S versions :)
Phil.
How do I get 1920x1080 output through the HDMI on the 5d3 running 1.2.3 while recording mlv/raw?
I only get something like 1620x910 which my viewfinder can upscale, but it is less sharp. When I record h264 i am able to get 1920x1080 out of the hdmi.
you need to enable mirroring but it's broken in magic lantern right now
hey everyone - this is probably a stupid question but i guess it's an easy one for you guys to answer: i would use ML on my 5dmk3 but mainly for photography, am i right that most of the "issues" are connected to raw-recording. would you say that the photo feature is "stable"
Quote from: TommiT on June 13, 2014, 10:42:54 PM
hey everyone - this is probably a stupid question but i guess it's an easy one for you guys to answer: i would use ML on my 5dmk3 but mainly for photography, am i right that most of the "issues" are connected to raw-recording. would you say that the photo feature is "stable"
I have only use the Dual ISO feature so far but ZERO crashes. Absolutely fine for me. But read other threads.
Quote from: dia3olik on June 13, 2014, 10:16:51 PM
you need to enable mirroring but it's broken in magic lantern right now
I have had no issues getting clean RAW picture out the HDMI with the latest nightly build.
Quote from: unfilmde on June 14, 2014, 09:16:41 AM
I have had no issues getting clean RAW picture out the HDMI with the latest nightly build.
It works only when mirroring lcd is on in canon menu...
Quick question. I know it is possible to shoot 4:3 in RAW mode but can you also shoot in this aspect ratio at h.264?
Quote from: pobox on June 14, 2014, 12:56:27 PM
It is clean but not 1920x1080
I get clean 1920x1080.
unfilmde, you get menus on the 5D mk3 LCD and TRUE CLEAN 1080P output???????
Quote from: dia3olik on June 15, 2014, 12:30:21 AM
unfilmde, you get menus on the 5D mk3 LCD and TRUE CLEAN 1080P output???????
It's not possible for the moment get ML menus. I hope Devs can work on this.
Quote from: dia3olik on June 15, 2014, 12:30:21 AM
unfilmde, you get menus on the 5D mk3 LCD and TRUE CLEAN 1080P output???????
No, I get clean out through the HDMI but no menus on the external monitor as it is CLEAN OUT. I get the ML menus on the canon built in monitor.
Quote from: unfilmde on June 15, 2014, 08:13:00 AM
No, I get clean out through the HDMI but no menus on the external monitor as it is CLEAN OUT. I get the ML menus on the canon built in monitor.
How can you get in the built in monitor ML Menus when you are connected by HDMI? Wich version are you using? I can't do that. Please, explain me!
exactly, same here...with 1.2.3
I get either menus on both or clean on both without menus...deactivating ML overlay
Check reply #566
thanks danne,
but that custom build has overlay on both, the LCD and HDMI,
but what I think would be great is overlay on the internal LCD and CLEAN 1080P out of HDMI...
Quote from: unfilmde on June 14, 2014, 10:44:33 PM
I get clean 1920x1080.
That is only possible when recording h264 or your recorder/viewfinder is upscaling to 1920x1080 (which is worse then h264)It works only when mirroring lcd is on in canon menu, but that is not efficient with a viewfinder as you won't see if it it is (still) recording
I use ML on my 60D for video but was hesitant to use it on my 5D3 because of the bootflag issue. I want to be able to remove the bootflag afterwards.
For video ML 1.1.3 is still recommended over ML 1.2.3. ML 1.1.3 sets the bootflag, however 1.2.3 can remove the bootflag.
Can i use the following workflow to be able to use ML Video and be able to remove the bootflag afterwards?
1) install ML 1.1.3 the normal way, which also sets the bootflag on the 5D3.
(bootflag is now set, slow start-up when not using ML)
2) do your thing.... film using ML video capabilities
3) upgrade firmware to 1.2.3
4) install ML 1.2.3
5) remove ML
(bootflag is now removed, firmware is back to Canon original)
Is this correct? If not, what should i do to be able to get bootflag removed?
http://www.magiclantern.fm/forum/index.php?topic=11803.msg114727#msg114727
QuoteOption A - Camera arrives with firmware 1.2.3) Downgrade the camera to 1.1.3, install ML, use it, upgrade to 1.2.3, remove bootflag.
Option B - Camera arrives with firmware 1.1.3) Install ML, use it, upgrade to 1.2.3, remove bootflag, downgrade to 1.1.3.
Thanks!
Please keep reading. discussed million times.
Quote from: zenclimber on June 16, 2014, 03:30:05 PM
I use ML on my 60D for video but was hesitant to use it on my 5D3 because of the bootflag issue. I want to be able to remove the bootflag afterwards.
For video ML 1.1.3 is still recommended over ML 1.2.3. ML 1.1.3 sets the bootflag, however 1.2.3 can remove the bootflag.
Can i use the following workflow to be able to use ML Video and be able to remove the bootflag afterwards?
1) install ML 1.1.3 the normal way, which also sets the bootflag on the 5D3.
(bootflag is now set, slow start-up when not using ML)
2) do your thing.... film using ML video capabilities
3) upgrade firmware to 1.2.3
4) install ML 1.2.3
5) remove ML
(bootflag is now removed, firmware is back to Canon original)
Is this correct? If not, what should i do to be able to get bootflag removed?
The uninstall procedure is not working. I did as suggested, install the ML card and update firmware and follow instructions. It just reinstalled ML 1.2.3
I then added Canon 5D300123.FIR to the ML disk (now both on there) thinking it would offer a choice and it just re-installed ML.
I then removed ML5D3123.FIR from the ML disk leaving Canon version plus ML files. This installed Canon again and it looked like I succeeded but when I remove the card and insert a new one it doesn't power up (I think the boot flag is still set).
I know the instruction say remove the boot flag but how does this happen?
If I can get the boot flag removed then Autoexec.bin won't be needed. Thats my guess.
Any ideas on how one removes the boot flag?
I may have answered this myself. It works anyway.
I took out the ML card and replaced with another pre-formatted SD card.
Then I ran "Clear all camera settings on Canon Menu - Wrench #4.
Now ML is gone but I will not use the other ML card again until more progress is made on ML for 5D3.
I can power off/on and works like before.
I have it on my 60D and it works a lot better.
Hope this helps anyone else.
Quote from: rickj on June 18, 2014, 04:38:34 AM
Then I ran "Clear all camera settings on Canon Menu - Wrench #4.
This does nothing to remove ML. The reason your camera powers up is because you used a card that was not bootable. Put that "ML" card back in and you'll have Magic Lantern again which means you did nothing to remove the bootflag.
Instead of blaming the software you should probably take the time to read and understand how the basics work because it's working flawless for the rest of us that do. I can upgrade/downgrade from 1.1.3 to 1.2.3 and back anytime I want and I don't have to set aside a "ML" card to remove ML.
you just don't want to read, do you
Uninstallation:
1) Run Firmware Update from your ML card.
2) Follow the instructions ->
for removing the boot flag please wait for 30 seconds.
Quote from: rickj on June 18, 2014, 04:38:34 AM
I may have answered this myself. It works anyway.
I took out the ML card and replaced with another pre-formatted SD card.
Then I ran "Clear all camera settings on Canon Menu - Wrench #4.
Now ML is gone but I will not use the other ML card again until more progress is made on ML for 5D3.
I can power off/on and works like before.
I have it on my 60D and it works a lot better.
Hope this helps anyone else.
Fair enough. It might be because I read this from Alex 1st post on this thread:
Installation:
1) Format the card from the camera.
2) Make sure you are running Canon firmware 1.2.3.
3) Copy ML files on the card and run Firmware Update.
Uninstallation:
1) Run Firmware Update from your ML card.
2) Follow the instructions.
What's hot:
- bootflag issue solved! (p.s. some bloggers got it wrong, you still enable it in the camera, but you can disable it by uninstalling)
- installation is really easy (simply unzip the files on the card, update firmware and you are ready to go)
- uninstallation is equally easy (update firmware and follow the instructions)
I definitely didn't read the part about waiting 30 seconds.......
Good it's working flawlessly for everyone else.
Has marekk submitted a patch for the build he made (discussed in post 556.. 566... one of those)? Trying to decide if I should take that build or if it's worth waiting a short period for it to show up in the nightly :)
His approach was a temp workaround I think...a1ex, do you know if in 1.2.3 the solution to have the HDMI clean output + menus on Camera LCD is near or if it's not possible to implement it in a clean way? ;)
Many thanks!
I installed ML on my Canon 5D3, when I enter the ML menu I don't get to control the digital or analog gain. The only thing I get to control is the speaker beep and speaker volume. Am I missing something? or is that how it's supposed to be?
Quote from: pngai on June 19, 2014, 01:37:04 AM
I installed ML on my Canon 5D3, when I enter the ML menu I don't get to control the digital or analog gain. The only thing I get to control is the speaker beep and speaker volume. Am I missing something? or is that how it's supposed to be?
- You should go to MODULES and selected what you need.
- Turn off, and turn on.
- After that, you should go to the MODULE that you have selected in the MENU.
- Press Q and put the values.
Example: you select RAW in MODULES. Turn OFF and ON. Go to ML Menu, Video, press Q over RAW.
Take a look in the manual and thread!
You are welcome to the wild side ;)
Quote from: pobox on June 15, 2014, 05:32:37 PM
That is only possible when recording h264 or your recorder/viewfinder is upscaling to 1920x1080 (which is worse then h264)
It works only when mirroring lcd is on in canon menu, but that is not efficient with a viewfinder as you won't see if it it is (still) recording
Can you see the ML menu in the viewfinder, when you are connected by HDMI?
Thanks.
Quote from: budafilms on June 19, 2014, 07:44:18 AM
- You should go to MODULES and selected what you need.
- Turn off, and turn on.
- After that, you should go to the MODULE that you have selected in the MENU.
- Press Q and put the values.
Example: you select RAW in MODULES. Turn OFF and ON. Go to ML Menu, Video, press Q over RAW.
Take a look in the manual and thread!
You are welcome to the wild side ;)
It still doesn't work :( I'm using a videomic pro and the buzzing noise in the background is killing me!!! Is there anything else I can do?
Quote from: budafilms on June 19, 2014, 07:47:55 AM
Can you see the ML menu in the viewfinder, when you are connected by HDMI?
Thanks.
NOT in mirror mode with 1920x1080 hdmi out, neither can I see the Canon menu.
In non-mirror mode i can see the ML and canon menu on the HDMI, but then I don't have an 1920x1080 output
How can I get a 1920x1080 output in the HDMI with overlays without using the canon LCD (not mirroring)??
I hope that would be possible soon!!
For the record, been awol IRL with school, kids etc, but just got the latest build from nightlies on my 5D3 1.2.3 and it seems loads better, the mlv format seems more solid now as well, and I've not seen any pink/corrupted frames in my limited testing, I just don't have one of those super fast computerbay or other cards that can handle raw at 80+Mbs. It is looking really good otherwise from what I've seen.
Thanks for the excellent work.
Quote from: pompeiisneaks on June 20, 2014, 01:23:15 AM
For the record, been awol IRL with school, kids etc, but just got the latest build from nightlies on my 5D3 1.2.3 and it seems loads better, the mlv format seems more solid now as well, and I've not seen any pink/corrupted frames in my limited testing, I just don't have one of those super fast computerbay or other cards that can handle raw at 80+Mbs. It is looking really good otherwise from what I've seen.
Thanks for the excellent work.
I believe if we are a more people requiring ML menu in viewfinder when it's connected, DEVs can develop that function.
This is reading for A1ex and more Hero Members. Crossfingers ;D
been contemplating giving ML a try for some time now.
i've read that audio doesn't work, how can i get around this ? I do not own an external recorder. also are you still able to take pictures with ML installed ?
i'll probably give it a try this weekend once i get all my questions answered. I'll ask more as i think of em, and i'll attempt to use the search feature to find some more answers..
I think you haven't read enough. Sound is possible with mlv, shooting photos is also possible, why shouldn't it?
Quote from: pcohen2 on June 20, 2014, 07:10:35 AM
been contemplating giving ML a try for some time now.
i've read that audio doesn't work, how can i get around this ? I do not own an external recorder. also are you still able to take pictures with ML installed ?
i'll probably give it a try this weekend once i get all my questions answered. I'll ask more as i think of em, and i'll attempt to use the search feature to find some more answers..
I shoot stills all the time with the latest build. No problems.
Quote from: unfilmde on June 20, 2014, 08:06:35 AM
I shoot stills all the time with the latest build. No problems.
thanks for the info
Hi everyone and nice to meet you :D
I wanted to install Magic Lantern on my 5D Mark III mainly for timelapses;
Is there a way to install ML only on the SD card; to avoid losing the changes I made in the settings of the machine; and then to have magic lantern only if I insert the sd?
thank you
Quote from: mercurio on June 20, 2014, 10:16:59 AM
Hi everyone and nice to meet you :D
I wanted to install Magic Lantern on my 5D Mark III mainly for timelapses;
Is there a way to install ML only on the SD card; to avoid losing the changes I made in the settings of the machine; and then to have magic lantern only if I insert the sd?
thank you
If you don't put the card with ML, you DSRL works with the original firmware.
You can save your settings even with ML running!
Thank you, so I don't have to do this step of the install guide of ML?
"Restore your camera to default settings (Clear settings, see picture above). Remember this will reset all canon settings and removes custom picture styles! "
Yep. Buy Canon C500 :)
Quote from: pngai on June 19, 2014, 03:48:39 PM
Is there anything else I can do?
Quote from: mercurio on June 20, 2014, 01:45:38 PM
Thank you, so I don't have to do this step of the install guide of ML?
"Restore your camera to default settings (Clear settings, see picture above). Remember this will reset all canon settings and removes custom picture styles! "
No. Put ML and enjoy!
Read the Manual Guide and Relax.
Hello, I just installed ML on my mark iii, and I'm getting two horizontal lines of dots across the frame. It pops up for one frame then goes away, then might pop up a few seconds later on another part of the frame. It's always only for 1 frame, and the timing in between is random.
Here are 3 frame shots from the clip showing the lines. Has anyone seen this before?
The nightly build is running smooth. I don't consider it bleeding edge anymore, not for a while now, anyway.
Excellent work.
The only thing I've encountered was a file that would not play in MLRAWViewer even though it was showing a file size of around 2.8GB. I processed it in RawMagic (which by the way automatically detects spanned clips now! Excellent!), and even though RawMagic couldn't see the FPS as 23.976, it still processed it to CinemaDNG and I was able to open it fine in After Effects as a RAW sequence. I don't know why MLRAWViewer couldn't play it back but in the end it worked.
So far no dropped frames, no green noise or pink dots here on my 5D Mark iii running the latest 1.2.3 build of 2014-06-21.
External monitor users, please have a look at this:
https://bitbucket.org/hudson/magic-lantern/pull-request/521/mirroring-support-for-external-monitors/diff
Quote from: chopper2585 on June 21, 2014, 04:21:39 AM
Hello, I just installed ML on my mark iii, and I'm getting two horizontal lines of dots across the frame. It pops up for one frame then goes away, then might pop up a few seconds later on another part of the frame. It's always only for 1 frame, and the timing in between is random.
Here are 3 frame shots from the clip showing the lines. Has anyone seen this before?
http://i890.photobucket.com/albums/ac104/chopper2585/ScreenShot2014-06-20at91143PM_zps70365976.png
http://i890.photobucket.com/albums/ac104/chopper2585/ScreenShot2014-06-20at91159PM_zps6542acff.png
http://i890.photobucket.com/albums/ac104/chopper2585/ScreenShot2014-06-20at91227PM_zps5ac032e9.png
Which card do you use?
Quote from: goran on June 23, 2014, 06:24:35 AM
Which card do you use?
I'm using a Komputer Bay 64gb 1000x. I'm noticing it at all resolutions.
Can you share your config file, the steps to reproduce, and how often you get the issue?
Does it happen with RAW, MLV or both?
External monitor or built-in LCD?
Other Canon settings?
A screenshot of Debug->Show EDMAC, without any modules loaded, in movie mode, should be also helpful.
Quote from: a1ex on June 22, 2014, 02:39:19 PM
External monitor users, please have a look at this:
https://bitbucket.org/hudson/magic-lantern/pull-request/521/mirroring-support-for-external-monitors/diff
Hi a1ex, is there an easy way to get the compiled code to test? Sorry, my programming days are so far away... Concentrating on creating content nowadays.
Cheers,
Andrew
Right now I'm interested in feedback from people with programming skills. After that, you'll be able to try it.
Quote from: chopper2585 on June 23, 2014, 06:50:04 AM
I'm using a Komputer Bay 64gb 1000x. I'm noticing it at all resolutions.
From my experience, and I may be completely wrong, this happens before the card is about to get corrupt. The only time I encountered something like this was after Komputerbay 64gb card was used with non UDMA 7 card reader which apparently corrupted it and after that I experienced something like this. Just my 2 cents.
Quote from: a1ex on June 23, 2014, 09:16:51 AM
Right now I'm interested in feedback from people with programming skills. After that, you'll be able to try it.
Thanks A1ex!
I think that a proper external support is a huge deal! ;)
I want to help too but I haven't any programming skills...let me know if you ever need someone to help you figuring bugs and using it on the field to improve it.
Quote from: goran on June 23, 2014, 08:06:27 PM
From my experience, and I may be completely wrong, this happens before the card is about to get corrupt. The only time I encountered something like this was after Komputerbay 64gb card was used with non UDMA 7 card reader which apparently corrupted it and after that I experienced something like this. Just my 2 cents.
Thanks, I went out today and took a lot of stills, finding a handful were corrupted. I'm thinking (hoping) that it is in fact the card. I have a Lexar UDMA 7 card reader, but the card might have been bad from the start. I have a new one coming Wednesday so I can test the SanDisk Extreme this time.
Quote from: a1ex on June 23, 2014, 06:59:10 AM
Can you share your config file, the steps to reproduce, and how often you get the issue?
Does it happen with RAW, MLV or both?
External monitor or built-in LCD?
Other Canon settings?
A screenshot of Debug->Show EDMAC, without any modules loaded, in movie mode, should be also helpful.
After getting some corrupted stills, I ordered a new card. Though it was benchmarking okay, maybe the card is going bad. I'll send you all the details if I still experience the issue on the new SanDisk I ordered. Thanks for the reply!
Quote from: chopper2585 on June 24, 2014, 05:05:05 AM
Thanks, I went out today and took a lot of stills, finding a handful were corrupted. I'm thinking (hoping) that it is in fact the card. I have a Lexar UDMA 7 card reader, but the card might have been bad from the start. I have a new one coming Wednesday so I can test the SanDisk Extreme this time.
After getting some corrupted stills, I ordered a new card. Though it was benchmarking okay, maybe the card is going bad. I'll send you all the details if I still experience the issue on the new SanDisk I ordered. Thanks for the reply!
Please report if the problem persists with the new card.
BTW I've had a couple of Lexar UDMA 7 card readers go crazy and corrupting files during transfer. Transferring the same files from the same card with a different reader didn't show any problems and the files were ok, so I'd check also a different reader just to be sure.
All best,
Goran
Quote from: goran on June 24, 2014, 08:25:52 AM
Please report if the problem persists with the new card.
BTW I've had a couple of Lexar UDMA 7 card readers go crazy and corrupting files during transfer. Transferring the same files from the same card with a different reader didn't show any problems and the files were ok, so I'd check also a different reader just to be sure.
All best,
Goran
Thanks for the heads up on those. I'll keep an eye on my reader in case that happens to any of my files.
I got the new card in today and everything works great, no more lines or issues, and the card is much faster. I can record continuously at 1920x1152 at 23.986.
Thanks for the help!
Having trouble deleting MLV files after playing them back in camera , I am using the mlv_play menu to delete it,but nothing not exit the play menu or go to another clip, Then an error pops up, Deleting 'A:DCIM/100EOS5D/M29-2131.MLV' failed, retrying...
Any idea anyone.
thanks.
Quote from: comurit on June 26, 2014, 09:37:49 PM
Having trouble deleting MLV files after playing them back in camera , I am using the mlv_play menu to delete it,but nothing not exit the play menu or go to another clip, Then an error pops up, Deleting 'A:DCIM/100EOS5D/M29-2131.MLV' failed, retrying...
Any idea anyone.
thanks.
I've had success just hitting the default delete button on the back of the 5D mark iii.
Guys I think it's better not to delete any files to avoid fragmenting the card...
Is fragmenting the card an issue? Does it slow things down? I have problems writing to a 1066x 128GB Lexar sometimes. I have to take a burst of photos or work my way up to 1920x1080 footage with smaller resolutions before the card starts writing at 90MB/s...Is that linked?
Hello guys,
Im using last couple months mlv raw with fw 1.2.3 and Im experiencing many problems with almost every build.
My issues are that when I record a few clips I get missing frames and in many clips I record are totally green! The strange thing is that when I play these green clips from
my camera with mlv_play the clips are looking ok but when I convert them to dngs to my mac or if I play the mlv with mlrawviewer then the clips are green and I can't fix them back to normal.
Im searching in the forum to find a solution but unfortunately I didn't.Any help would be much appreciated.
Quote from: comurit on June 26, 2014, 09:37:49 PM
Having trouble deleting MLV files after playing them back in camera , I am using the mlv_play menu to delete it,but nothing not exit the play menu or go to another clip, Then an error pops up, Deleting 'A:DCIM/100EOS5D/M29-2131.MLV' failed, retrying...
Can you check if this helps? https://bitbucket.org/hudson/magic-lantern/issue/2022/mlv_play-destroy-data#comment-10957992
Quote from: a1ex on June 27, 2014, 10:48:51 PM
Can you check if this helps? https://bitbucket.org/hudson/magic-lantern/issue/2022/mlv_play-destroy-data#comment-10957992
It didn't help, what I did is format in exfat the lexar 1066x 64 gb, offloaded the modules and loaded again, record 1920x1080 and play the video, it worked, exit and deleting was possible, i did some recording in crop mode and I am back to where I was in the first place.
I hope this helps.
so far its working pretty well. I have also found that the first frame or two in a recorded sequence dont record. however this is indicated during record time.
Also at first I was unable to record 1920x1080 ML Raw with my Lexar 1000x speed card. but then for some reason it seemed to work fine and has been fine for the remainder
of the testing.
I have also noted the camera warming up quit significantly more than before with the older 113 builds.
But super happy though... would love to get 40fps working at 1920X1080 again. wink
I had similar troubles not to be able to delete a file after viewed it from the MLVPlayer.
Second bug, File Manager never print the real file weight when the file is too big (more than 10GB).
Thanks,
S.
With the latest build I downloaded today I think the problem with missing frames is gone but I still get greenish clips sometimes.Any fix for this? can someone help me please?
Quote from: Jolly Roger on March 16, 2014, 09:53:52 PM
If you have the bootflag already enabled, just upgrade to 1.2.3 Canon firmware, power off the camera, put ML (1.2.3 build) on card, et voilà.
I must have missed something because that doesn't seem to work for me.
I'm running 3115 then go to the canon menu, press firmware ver 1.1.3ml-2.3.it asks if I want to upgrade, I press yes then it goes to lack with the red light blinking for a while, so long that I have to take the battery out.
It seems I may be running the version 2.3 now but I still can't use the camera without the sd card in, is that normal?...
Cheers
Format card using a cardreader. Insert card into cam and format again. Copy Canon firmware version 1.2.3 to card (cardreader again). Insert card into cam and run Canon's firmware upgrade procedure.
MLV RAW (1920x1080 build up to date of the post) it's working every build worst. Now I have to loose two shots of seconds to get an entire shot. Even setting all memory hacks and global off.
Sorry for say these. I know it's a very hard work for devs.
After I can get more shots with the same card. I did a full length movie with MLV, something impossible today.
I tried with other 5d Mark III , and difference CF cards, and the problem it's the same.
I am using .RAW where I don't have any problems.
I hope Devs can define how to stabilise MLV.
Thanks.
Hmm. Perhaps you should delete the ml config files and cope the complete directory onto the card.. I think it works great here. But now i will have to try the newest built.. ;(
Quote from: swinxx on June 29, 2014, 08:56:50 AM
Hmm. Perhaps you should delete the ml config files and cope the complete directory onto the card.. I think it works great here. But now i will have to try the newest built.. ;(
I did!
If you try tell me how it works!
I can share and test to help, of course. I want to go forward with ML ;)
Hello, I discovered that when I press garbage (delete) button during rec, the borders top and above become transparent.
It should be really nice to have it always to prevent microphone or anything entering in the frame .. too late..
I would like to know if it could be possible to assign the magic zoom button during rec to à right button (af-on should be perfect) as I focus with left hand.
I love ML and can't work without anymore.
Sincerely
Yvan
Does anybody worries about that too ?
1 month and no answers, so stupid questions ?
I just made the jump to 1.2.3 so I apologize if this has already been noted, but it seems that when I switch into photo mode from video and change the manual autofocus switch on the lens from off to on (or on to off,) the camera shuts down. I was able to replicate it once but not a second time... any ideas?
Any error logs?
Try to reproduce, and if you can, film the camera screen and attach your settings folder.
Thank you for this excellent information but I cant seem to even get passed downloading the ML files from the link. I click and nothing happens at all. Any ideas as to what the problem may be? I've never had any problem downloading anything in the past.
http://builds.magiclantern.fm/jenkins/job/5D3.123/30/artifact/platform/5D3.123/magiclantern-Nightly.2014Jul01.5D3123.zip
Sorry to break the current flow of your discussion.
But I got a question about the latest development regarding higher fps and higher resolution.
Am I correct to understand that the footage is no longer stretched? and if so, is 1920x872 2:20.1 at 48 fps possible?
And is this fps hack also possible on 1.1.3?
Thank you
For un-stretched FPS: I think you can configure the sensor to output a cropped image with square pixels, by changing ADTG 0x800C and 0x8000 (but I don't know how to increase the resolution, so you'll end up with a very wide aspect ratio). I didn't test it at high fps though, because the overhead of adtg_gui is too large.
For the other question, it takes 5 minutes to try and find out.
On my T5i i can access a 1080p crop mode (uses only center of sensor)...
Recently got a 5d3 and cannot seem to find this feature.
Where in the menus can it be found, or does it exist?
Running July 1, 2014 firmware.
Thanks for all the hard work, I've got the latest nightly for 1.2.3 on my 5D and it's working fantastically.
There's just one problem I've noticed though. When I connect anything to the HDMI port and set the 5D to mirroring so that none of the Canon info comes up on the HDMI out, the ML overlays on the back of the camera are not shown even though the screen is on.
When I go into the menu it tells me to press the INFO button to get rid of the Canon menus, however I've tried this and it still won't display, instead with the same error.
Thought this might be of help to you
Quote from: alfo on July 03, 2014, 07:58:11 PM
When I connect anything to the HDMI port and set the 5D to mirroring so that none of the Canon info comes up on the HDMI out, the ML overlays on the back of the camera are not shown even though the screen is on.
Quote from: a1ex on June 22, 2014, 02:39:19 PM
External monitor users, please have a look at this:
https://bitbucket.org/hudson/magic-lantern/pull-request/521/mirroring-support-for-external-monitors/diff
Waiting for review ;)
I just demoed that, and it worked great for me... I've updated the same on the bitbucket page.
Quote from: a1ex on July 03, 2014, 08:15:56 PM
Waiting for review ;)
If you want, tell me what I have to download and I will test it!
Thanks a1ex, that's exactly what I'm looking for.
Will happily test it out - is there a guide as to how to set up and compile Magic Lantern on OS X?
Hello folks,
first of all, thank you for your hard work here! ML is great.
I used it on my old 7D and now want to use it on my new 5D mark iii with firmware 1.2.3
Im sorry, but I have some safety questions:
As I understand I have to:
Installation:
1) Format the card from the camera.
2) Make sure you are running Canon firmware 1.2.3.
3) Copy ML files on the card and run Firmware Update.
My questions: Can I make the update from a CF-Flash Card? I read here often only about SD-Cards?
My second question: Do I need to put the mode dial on a specific position (for example M or so)?
And at last, which build is safe to use?
Can I make the update from a CF-Flash Card? Yes I did it. But it's faster in my case, when you have ML in the SD card and let the CF for videos.
Do I need to put the mode dial on a specific position (for example M or so)? Use M. You can switch and try the other modes. But I use often M.
And at last, which build is safe to use? Build from June works fine. Depends if you going to try the very last things.
Quote from: budafilms on July 04, 2014, 09:31:55 PM
Can I make the update from a CF-Flash Card? Yes I did it. But it's faster in my case, when you have ML in the SD card and let the CF for videos.
Do I need to put the mode dial on a specific position (for example M or so)? Use M. You can switch and try the other modes. But I use often M.
And at last, which build is safe to use? Build from June works fine. Depends if you going to try the very last things.
Thank you very much for your answer!
I tried it now and it works! I will only use it for photography, not for video.
I used the build from July, 01. I wonder when there will be at least a alpha version?
Quote from: mlguest on July 04, 2014, 11:46:01 PM
Thank you very much for your answer!
I tried it now and it works! I will only use it for photography, not for video.
I used the build from July, 01. I wonder when there will be at least a alpha version?
Only Devs know that.
But don't worry, use it, read the guide and if you can donate!!!! ;)
Hi I have a problem, to make you better understand I am attaching a video, https://www.dropbox.com/s/lazkcyiwvj0gp1k/20140703_085411_001.3gp (https://www.dropbox.com/s/lazkcyiwvj0gp1k/20140703_085411_001.3gp) . So during a timelapse (interval 4sec and exposure 0,5") as you can see from the video at sec 7-8 and 22-33, the camera takes two shots. I don't know if they are skipped frames or other (I have ML on the SD and I was registering the files on a 32GB 1000x komputerbay). What do you think? Thank you
Quote from: budafilms on July 05, 2014, 04:18:45 AM
Only Devs know that.
But don't worry, use it, read the guide and if you can donate!!!! ;)
O.K., I will do that. Thank you again.
I wonder if I want to use ML on several cards, if it is o.k. to copy my first installation from the first card to another card, so that I can use the same settings on every CF-Card?
hi guys.
any chance of fixing the disappearing of iso/wb adjustment (the joystick function) after hitting rec? works fine until i hit rec, then it vanishes ;)
im using magiclantern-Nightly.2014Jul04.5D3123 atm
Quote from: peter221 on July 06, 2014, 09:45:58 PM
hi guys.
any chance of fixing the disappearing of iso/wb adjustment (the joystick function) after hitting rec? works fine until i hit rec, then it vanishes ;)
im using magiclantern-Nightly.2014Jul04.5D3123 atm
Press Rate.
Bug? Nightly 4.Juli, canon 5d mk3, global draw on, lens doesn´t matter...
when setting up ml iso gain to -1.0 and then setting zebras to less than 99% the highlights in the viewer are pink.
dont know if this behavior is also in other nightlies..
thx
http://wiki.magiclantern.fm/userguide#iso
Just wanted to say big thank you to developers who have worked on this version, it's really, really impressive update to my camera featurewise. Setup was as simple as it could possibly get, i think.
Quote from: budafilms on July 07, 2014, 04:58:39 AM
Press Rate.
I know that the Rate key brings up the iso/kel adjustment
I would like the iso/kel not to dissapear after hitting rec. What's more after stopping recording it doesn't come back. I have to hit rate once more.
I hope im making myself clear.
Hi guys.
I'm new to the world of MagicLantern and I found out that this is the latest version for the Mark III.
I've read that his was released around March, but can someone who is very knowledgeable about this version tell me: how is it going about now? It's pretty safe to install the latest nightly build? Or should I wait for some issues to be resolved?
Thank you in advance.
Wonderful firmware!!
It's never 100% safe. install it at your own risk.
Quote from: victorinox126 on July 09, 2014, 12:49:06 AM
Hi guys.
I'm new to the world of MagicLantern and I found out that this is the latest version for the Mark III.
I've read that his was released around March, but can someone who is very knowledgeable about this version tell me: how is it going about now? It's pretty safe to install the latest nightly build? Or should I wait for some issues to be resolved?
Thank you in advance.
Which beneficts for example i can have using ML in my 5dm3 shooting night long expo?for example shooting milky way..
Hi,
I'm having some issues with rack focus on the 5D III. I'm running the July 3, 2014, nightly build. I'm using a Canon 50mm F1.2 prime lens.
I manage to save my endpoints correctly. But when I run the rack focus itself, it seems to not go all the way. For example, if I go from a focus range of 23 inches to 36 feet, starting at 23 inches it will stop at around 4 feet. Similarly, from the 36 feet coming back, it stops at 4 feet.
I seem to be having similar problems with other lenses, though I haven't tested as thoroughly.
Any suggestions?
Thanks,
Joe
Anyone know what the last version of the nightly builds creates .raw files instead of .mlv files? I want to be able to use RAW Magic and not have to go through the extra step of converting everything to .raw first.
Thanks.
I'm having some issues with the latest nightly (2014-07-04).
Trash button to enter magic lantern menue sometimes works, most of the time it is not working. I just get the first ml screen, but if I press the trash button and next half shutter, I enter the ml menue.
Automated follow focus with mlv_viewer loaded crashes the camera when pressing play to start the folllow focus ramping while recording. I'm not sure if this was an issue before, because I usually used the filemanager instead of the mlv_viewer before. Without mlv_viewer loaded everything works.
Audiolevel indicater within the ml menue with mlv_snd enabled is stuck.
I installed this nighly on a clean cf-card without any older prefs on it.
Quote from: devocam on July 10, 2014, 08:07:35 PM
Anyone know what the last version of the nightly builds creates .raw files instead of .mlv files? I want to be able to use RAW Magic and not have to go through the extra step of converting everything to .raw first.
Thanks.
Just load the RAW module and turn off MLV Raw. I use RAWMagic all the time, it automatically recognizes spanned clips. It is great.
Thanks! I didn't realize the old module was still in there.
Quote from: unfilmde on July 10, 2014, 11:45:26 PM
Just load the RAW module and turn off MLV Raw. I use RAWMagic all the time, it automatically recognizes spanned clips. It is great.
The major difference between RAW and MLV is that MLV supports audio as well as the Video. Otherwise I think the quality is identical. Both are RAW. MLV is Magic Lantern's own RAW codec. So if you always do separate audio and don't need a sync beep on the video to sync your audio up, then RAW is perfect.
~Phil
Quote from: pompeiisneaks on July 11, 2014, 12:28:33 AM
The major difference between RAW and MLV is that MLV supports audio as well as the Video. Otherwise I think the quality is identical. Both are RAW. MLV is Magic Lantern's own RAW codec. So if you always do separate audio and don't need a sync beep on the video to sync your audio up, then RAW is perfect.
~Phil
I agree. My one caveat about using MLV Raw is it is a new codec. I prefer a codec that is established, if MLV Raw gets discontinued, you may end up with files you can't use later on. I'm sure it will be around for a while, but I've been burned a few times.
The ability to embed sound is great, but I don't mind using a slate and double system-ing it.
Quote from: mlguest on July 05, 2014, 12:17:06 PM
O.K., I will do that. Thank you again.
I wonder if I want to use ML on several cards, if it is o.k. to copy my first installation from the first card to another card, so that I can use the same settings on every CF-Card?
Yes, you can!
Quote from: budafilms on July 11, 2014, 05:04:13 AM
Yes, you can!
[/quote
Thank you. Than change is possible. :-)
Quote from: unfilmde on July 11, 2014, 04:49:37 AM
I agree. My one caveat about using MLV Raw is it is a new codec. I prefer a codec that is established, if MLV Raw gets discontinued, you may end up with files you can't use later on. I'm sure it will be around for a while, but I've been burned a few times.
The ability to embed sound is great, but I don't mind using a slate and double system-ing it.
The end result of converting ML raw/mlv is DNGs/CDNGs. The industry has long supported CDNGs and presently can support DNGs as well (ACR), but more and more post production apps are getting on board with directly supporting DNGs like DaVinci Resolve, a trend I expect to continue considering the popularity of ML and it's growing usage as a professional platform.
Hi guys,
I have instaled the last build 4/7 on my 5dm3 version 123 and try to record ML video. If I am not losing frames during one minute the recording stops automaticaly when I reach 1 minute. Sometimes i see the message on display that says i am losing frames and recording stops. I am using Lexar 64GB 1066 and lexar 256 1066 cards. The problem seems to be the same ragardles what card i choose. Both cards are formated by camera.
Is ir possible to record more that 1 minute continuously? Any sugestions please.
I forgot that I shoot full HD 1920x1080 25fps PAL.
Yes, it's possible to shoot up to 30fps continuous at 1080p.
Did you disable or set to 30 mins. the auto-shutoff feature in the Canon menu?
When shooting raw the camera does not detect activity :)
Also, did you do an in-camera speed test of your cards to see if they can handle the data rate needed?
hi Jimmyd30.
Thanks a lot. I had not changed auto-shutoff function in Canon menu. A question how can you do speed test of the cards?
Is it possible to use focus peaking during video recording? It works before i start recording.
Quote from: jarandov on July 13, 2014, 09:44:42 AM
hi Jimmyd30.
Thanks a lot. I had not changed auto-shutoff function in Canon menu. A question how can you do speed test of the cards?
See here: http://www.magiclantern.fm/forum/index.php?topic=12630.msg121745#msg121745
Hi, have a couple of questions that i hope you guys can answer.
I recently upgraded from a 7D to the 5D3. Installed ML over 1.2.3 without any problems. However i only got about 60mb/s write speed with my SanDisk 32GB 120mb/s. decided to do a low level format of the card and also took the opportunity to format the card as exFat.
Do i need to do the installation (firmware update) again after copying the ML files back to the card? ML wont boot atm...
I ve seen threads where people install ML to the secondary SD card, is that something worth considering? Any pointer on how to do that?
Thanks in advance!
/calle
http://www.magiclantern.fm/forum/index.php?topic=12476.msg121903#msg121903
Quote from: Audionut on July 15, 2014, 01:31:48 PM
http://www.magiclantern.fm/forum/index.php?topic=12476.msg121903#msg121903
Ouch.. Well thanks for the fast answer. Transend 1000x ordered.
How about my ML not booting atm. Any solution to this?
Quote from: cathor on July 15, 2014, 12:55:21 PM
Do i need to do the installation (firmware update) again after copying the ML files back to the card? ML wont boot atm...
I ve seen threads where people install ML to the secondary SD card, is that something worth considering? Any pointer on how to do that?
You need to make the card bootable. With new ML installs this happens automatically now, but since you reformatted the card you need to run EOScard on it, see here: http://www.magiclantern.fm/install.html
As for putting ML on the SD card, I do it that way because then I can just swap out non-ML CF cards when they're full and not worry about having ML on them. Especially helpful when/if you're in a jam and need to borrow/buy another CF card on the spot and can't install ML on it at that moment.
To do such, after ML install, just copy everything onto SD card, make it bootable and you're good to go (DO NOT NEED TO RUN FIRMWARE UPDATE AGAIN).
Quote from: jimmyD30 on July 15, 2014, 02:15:27 PM
You need to make the card bootable. With new ML installs this happens automatically now, but since you reformatted the card you need to run EOScard on it, see here: http://www.magiclantern.fm/install.html
As for putting ML on the SD card, I do it that way because then I can just swap out non-ML CF cards when they're full and not worry about having ML on them. Especially helpful when/if you're in a jam and need to borrow/buy another CF card on the spot and can't install ML on it at that moment.
To do such, after ML install, just copy everything onto SD card, make it bootable and you're good to go (DO NOT NEED TO RUN FIRMWARE UPADTE AGAIN).
Great, thank! Can't remember that i had to do that the first time I installed ML on the 5D3. Remember i did that for the 7D though. Alzeimer Light kicking in i guess. Is MacBoot the OSX equiv. of EOScard btw?
They've modified the install process to make the card bootable automatically now upon ML install ;)
MacBoot seems to be equivalent as EOScard, but I've never tried it, see here: http://www.zenoshrdlu.com/macboot/macboot.html
As jimmyD30 suggests, you need to make the card bootable.
When you run the ML firmware updater, it will make the card bootable.
So you can either make the card bootable with some application, or just run the firmware installer from the new card.
First time poster and had a quick wuestion that i couldnt find definitively on other threads. Just did a shoot using 1.2.3 on mark III using .raw module with a lexar 1066x 128gb card and I'm getting crazy vertical lines through the video on all dngs when converted using magic raw. A lot of people are saying it's the sensor noise pattern etc.
Is there a definitive fix for this? I was using hdmi out while recording but I doubt that would make a difference. Any thoughts or fixes?
Quote from: Brock2621 on July 16, 2014, 01:42:50 AM
First time poster and had a quick wuestion that i couldnt find definitively on other threads. Just did a shoot using 1.2.3 on mark III using .raw module with a lexar 1066x 128gb card and I'm getting crazy vertical lines through the video on all dngs when converted using magic raw. A lot of people are saying it's the sensor noise pattern etc.
Is there a definitive fix for this? I was using hdmi out while recording but I doubt that would make a difference. Any thoughts or fixes?
Are you sure don't used DUAL ISO Module? Check it.
And to test the sensor, just take a shoot with H264 ;)
And it the problem persist upload a DNG frame to get opinions.
Quote from: budafilms on July 16, 2014, 05:46:03 AM
Are you sure don't used DUAL ISO Module? Check it.
And to test the sensor, just take a shoot with H264 ;)
And it the problem persist upload a DNG frame to get opinions.
Isn't dual ISO mode horizontal lines?
Here's a link to a DNG for viewing. If you mess with the contrast it gets even worse :(
https://www.dropbox.com/s/vabnza3gj10bcac/M12-1248_C0000_03988.dng
Quote from: Brock2621 on July 16, 2014, 01:42:50 AM
First time poster and had a quick wuestion that i couldnt find definitively on other threads. Just did a shoot using 1.2.3 on mark III using .raw module with a lexar 1066x 128gb card and I'm getting crazy vertical lines through the video on all dngs when converted using magic raw. A lot of people are saying it's the sensor noise pattern etc.
Is there a definitive fix for this? I was using hdmi out while recording but I doubt that would make a difference. Any thoughts or fixes?
Are you using RawMagic? If so, the lite version or the full version? If you are using RawMagic version 1.2 has a fix vertical stripe function. If you are using Magic Raw then I don't know what that is.
Personally using RawMagic full version, I have not seen the vertical stripes.
Quote from: Brock2621 on July 16, 2014, 04:47:38 PM
Isn't dual ISO mode horizontal lines?
Here's a link to a DNG for viewing. If you mess with the contrast it gets even worse :(
https://www.dropbox.com/s/vabnza3gj10bcac/M12-1248_C0000_03988.dng
Appears like HDR it's working.
Reset ML to default values or better, format card and put again without save any settings.
Put only MLV Module on and try again in daylight.
Hi all new here xD any1 have "Video tutorial" how to install Magic Lantern for 5D Mark III 1.2.3 Thanks All have nice Day
First post of this thread will be fine start to read.
Tell us what your troubles are with this short but instructive installation step list.
Hi,
So I've been lurking for a few months but first post. I've been using ML for testing RAW video, every once in a while, nothing serious yet. Started with the 1.1.3 firmware, then just tried it with 1.2.3.
My biggest problem right now is some "pink noise" in a few frames -- I'd estimate 2-5 frames per minute. The noise shows up in horizontal bands across the image. Here is a frame as an example: http://yoderdev.com/photos/000063.jpg
History: I had this issue right away with the 1.1.3 firmware, but eventually it went away. At one point I recorded some 6 or 7 minutes in one clip with none of this at all. I'm not quite sure what I did to change this. In my forum lurking, I don't believe I've seen anyone else with this problem. I used to see some reports of purple frames, but I think it was a different issue.
Yesterday was the first day I tried with 1.2.3. It is back; the above image was from yesterday.
Another weird issue - yesterday I recorded a couple minutes and I think the record icon stayed green the whole time. Today I tried again, and it started yellow, then red, then stopped after about 10-20 seconds. I'm not sure what is different. Global draw is off (it was on yesterday but I tried it both ways). I made sure it was being recorded to the CF card, not SD.
ML itself is running on the SD. My CF cards are KomputerBay 128GB 1000x. Yeah I know, people have said the 64GBs are more reliable. However, as noted, they have been working all right for me until today. I have two cards, same with both. I don't think card fragmentation could explain the sudden drop?
I'm recording 1080p, 24fps.
Any tips for either issue would be greatly appreciated. Thanks, and keep up the good work!
BTW, for kicks, I'll share the script I'm using to convert and process all the raw videos on the card in one fell swoop. This is in bash shell under Linux.
for x in /run/media/micah/8F7B-5048/DCIM/101EOS5D/*.RAW; do X=`basename $x .RAW`; echo $X; mkdir $X; cd $X; wine /home/micah/bin/raw2dng.exe $x; ufraw-batch --out-type=tiff --exposure=0 *.dng; ffmpeg -i %6d.tif -vcodec mjpeg -qscale 1 video.avi ; cd .. ; done
The path is of course to my CF card.
I'll also note that the card is formated exfat and the pink noise appears in the source DNG files.
I think I've come across this issue in the forum before, but don't remember the discussion.
There's been talk that there's a problem specifically with the KB 128GB 1000x cards and ML, you can search and find out more. It might just be the cards themselves, as I've recently seen this specific card being sold at deep discount.
A few things you could try, reformat cards in camera and reinstall ML, use mlv_rec instead of raw_rec and try copying files to local hard drive then process with a different app like MLV Mystic, MLRawViewer, or MLRawBrowser and see if things improve :)
I'll try that in the next couple days. Only problem with formatting the card in the camera - isn't it then VFAT instead of exfat, which would limit the file sizes? Or is that not a real concern?
Looks like KomputerBay has 64GB 1066X cards for $95 - maybe I should pick up one of those and see if there's a difference.
You're correct about FAT32 vs exFAT, but for now doing diagnostics, let's go step by step. I'm sure exFAT will be no problem, but when trying to find cause of issue, best to eliminate as many factors as possible.
Yes, I'm looking at that exact KB card myself, probably get one or two. Here's some talk about it: http://www.magiclantern.fm/forum/index.php?topic=11428.msg122802;topicseen#msg122802
Quote from: yodermk on July 21, 2014, 02:52:29 PM
I'll try that in the next couple days. Only problem with formatting the card in the camera - isn't it then VFAT instead of exfat, which would limit the file sizes? Or is that not a real concern?
Looks like KomputerBay has 64GB 1066X cards for $95 - maybe I should pick up one of those and see if there's a difference.
Yes it would be. But I have used RAWMagic and it is able to take the spanned RAW files and merge them for processing into one CDNG file. So exFat has become moot for me. I'm on a Mac. YMMV.
Exactly, for me I prefer many 4GB files over few large files for safety/practical reasons at this point.
I'm glad that with using exFAT format ML can break the 4GB file barrier and it was much appreciated before the apps could process multiple raw files automatically, but recently I've defaulted back to the 4GB file size.
When you full the CF, appears the same message like you haven't format the card as Exfat ;)
Quote from: budafilms on July 21, 2014, 08:13:53 PM
When you full the CF, appears the same message like you haven't format the card as Exfat ;)
Yep. I got that message as well and actually my final clip had an all black corrupted frame every couple of seconds. Have only filled the card up once, so I will try again and see if the final clip is corrupted again, anyone else getting a bad final clip when they fill up their cards? I'm using a Lexar 32gb 1066x card which has had absolutely zero problems so far, so I don't think it was the card.
I just ran a test with KB 32GB 1000x CF card on 5DM3, shot .mlv with 4GB files (not using exFAT format) until card full with no issues.
Are you using a build which has Reserve Card Space option (creates a mlv_rec.tmp file)?
Quote from: a1ex on May 12, 2014, 08:59:06 AM
RAW and MLV are not the core of ML, they are just applications (sure, very popular ones). There is a forum area dedicated to raw recording (http://www.magiclantern.fm/forum/index.php?board=49.0), so please discuss raw issues there.
I prefer this thread to be about core issues specific to 5D3 (in particular, problems introduced in 1.2.3 that did not exist in 1.1.3).
edit: Lets keep the further off-topic nonsense out of the thread. There's no need for CAPITALS, finger pointing or any other nonsense. It's no big deal, I'm always dragging threads off topic. This is just a gentle reminder to keep this thread on topic please.
A developers time is limited, and it only becomes wasted when the dev has to trawl through a bunch of off-topic nonsense, or other discussion that is better suited to other areas of the forum.
Thanks.
I read the planet5D article about the release of the 1.2.3+ML and I just got my 5D Mark III few days ago. I read and had to decide whether to stick with 1.2.3 which was pre installed in my 5d or go with the "safer" 1.1.3. After thinking about it thoroughly, I decided to get the 1.1.3+ML because I just got my camera and I really didn't want to take a chance of breaking my camera so quickly and mourn over the death of my camera. After 2 years later now, ML should have a stable 1.1.3 5D.Mark.III Magic lantern working. No disrespect to any of the HARD WORKING ML crew!
Quote from: itsDPmikey on July 22, 2014, 05:42:45 AM
I read the planet5D article about the release of the 1.2.3+ML and I just got my 5D Mark III few days ago. I read and had to decide whether to stick with 1.2.3 which was pre installed in my 5d or go with the "safer" 1.1.3. After thinking about it thoroughly, I decided to get the 1.1.3+ML because I just got my camera and I really didn't want to take a chance of breaking my camera so quickly and mourn over the death of my camera. After 2 years later now, ML should have a stable 1.1.3 5D.Mark.III Magic lantern working. No disrespect to any of the HARD WORKING ML crew!
It's at your own risk. 1.1.3 or 1.2.3 at the same level ;)
Don't scare to other people to try.
Read an taste. Enjoy and produce nice videos.
I originally posted this in the nightly build forum, but as no response guess I must have put it in the wrong place.
>>>
Installed the 1st July 2014 nightly build (my first time use of the software) onto a Kingston 16Gb CF card to use in my 5DMk3 camera.
All seemed ok with the installation, and I went out to take some photos. I dont switch the camera on and off in a session just leave it on.
I was finding between photos that I was having to press the shutter button partially for a couple of seconds for the camera to come out of what seemed to be a hibernation.
After appx 20 photos, everything went dead.
I replaced the battery - no change.
So I then put another card in without ML installed - still dead.
I then put the original battery back in and the camera recommenced working (obviously without ML).
The replacement battery I had also tried, worked as well when I used that next.
Somehow the ML installed CF card had become corrupted I later identified.
Anyone else had this problem or any idea what the problem is. This is the first card I have had corrupt in this camera, and in years of using them never before a Kingston one.
It reformatted ok via my PC, then I was able to put it back in the camera and reformat it in there and it now works fine again (still without ML)
I'm not a programmer so am reliant on all of you guys who are for guidance - thank you.
Incidentally, I went to check the Camera firmware status, and only the Canon one is showing now, obviously not ML because I didnt reinstall it, however I see some topics referring to BootFlag needing to be removed - however my camera still seems to be booting up almost instantly - dont know if this is relevant information for you or not
I dont use the camera for video it is for stills only
Quote from: Mystery57 on July 23, 2014, 02:46:32 PM
I originally posted this in the nightly build forum, but as no response guess I must have put it in the wrong place.
>>>
Installed the 1st July 2014 nightly build (my first time use of the software) onto a Kingston 16Gb CF card to use in my 5DMk3 camera.
I highly recommend putting ML on a separate SD card and capture to a CF card. It has worked and been very stable for me this way. And you don't have to worry about reformatting the CF card and loosing ML.
Does anyone else have a missing H.264.ini with 1.2.3? Am I supposed to do something to get the H.264 mode back in ML, or is it not part of 1.2.3 yet?
Quote from: unfilmde on July 23, 2014, 07:30:56 PM
I highly recommend putting ML on a separate SD card and capture to a CF card. It has worked and been very stable for me this way. And you don't have to worry about reformatting the CF card and loosing ML.
+1
That is what I do and so I can swap out my CF card without worry.
Quote from: jordanwalkert on July 23, 2014, 08:58:27 PM
Does anyone else have a missing H.264.ini with 1.2.3? Am I supposed to do something to get the H.264 mode back in ML, or is it not part of 1.2.3 yet?
I use H264 and Raw.
The only thing I do is put off Raw Module and MLV Sound.
Quote from: budafilms on July 24, 2014, 07:12:30 AM
I use H264 and Raw.
The only thing I do is put off Raw Module and MLV Sound.
Hmm, so your H264 mode is showing up in ML 1.2.3 and doesn't say that the .ini is missing?
Quote from: jordanwalkert on July 24, 2014, 07:51:51 AM
Hmm, so your H264 mode is showing up in ML 1.2.3 and doesn't say that the .ini is missing?
It's not in the ini. It's the first or second thing under the movie tab, on by default but overridden when you turn on RAW or MLV RAW record in the ini.
Quote from: jordanwalkert on July 24, 2014, 07:51:51 AM
Hmm, so your H264 mode is showing up in ML 1.2.3 and doesn't say that the .ini is missing?
I believe the h264 .ini file is only used for bit-rate override, so it's not required for shooting native h.264, just if you want to use a different bit-rate other than canon default.
So the 'error' message you are seeing is normal and you can shoot h.264 without the missing .ini file.
Quote from: unfilmde on July 23, 2014, 07:30:56 PM
I highly recommend putting ML on a separate SD card and capture to a CF card. It has worked and been very stable for me this way. And you don't have to worry about reformatting the CF card and loosing ML.
Does it matter what size or class the SD card is? I remember reading on this forum at one point that it was NOT suggested to use an SD card because the write speed was throttled to the slowest speed card in the camera (between the SD and CF cards inserted). Is that no longer true? (Or maybe it was never true?)
Doesn't matter unless you plan on using card spanning feature, if so then you're dealing with a 20 MBps camera data bus limit with the SD card anyway. The fastest write speed ML uses does not correspond to the lowest card speed in the camera, but rather to the card selected for recording.
hello all,
I am a long time user of magic lantern. was shooting a lot over the last year with the 1.1.3 version of raw.
now I updated to 1.2.3 and everything looked fine so far.
today I rigged the markIII with my tv-logic58 monitor via hdmi for the first time. all tests before were done without the use of the hdmi-out.
it is now not possible to record longer clips than 1min in mlv 1920:1080 25p mode. icon always stays red or yellow. the build is from 16th of july.
as soon as I disconnect the hdmi everything goes green and fine! what does the performance have to do with the hdmi out?
did I set up something wrong somewhere? checked everything, can`t think of anything?!?
thank you so much for every help! i have an upcoming job tomorrow and if I don`t find a solution I have to shoot in h264;-(
tobi
Quote from: tobiascorts on July 27, 2014, 08:43:25 PM
hello all,
I am a long time user of magic lantern. was shooting a lot over the last year with the 1.1.3 version of raw.
now I updated to 1.2.3 and everything looked fine so far.
today I rigged the markIII with my tv-logic58 monitor via hdmi for the first time. all tests before were done without the use of the hdmi-out.
it is now not possible to record longer clips than 1min in mlv 1920:1080 25p mode. icon always stays red or yellow. the build is from 16th of july.
as soon as I disconnect the hdmi everything goes green and fine! what does the performance have to do with the hdmi out?
did I set up something wrong somewhere? checked everything, can`t think of anything?!?
thank you so much for every help! i have an upcoming job tomorrow and if I don`t find a solution I have to shoot in h264;-(
tobi
next step was a total reset of the camera including magic lantern build 07.16.2014. supposedly stable.
same problem, no clips longer than 1min, though camera icon turns green now, before it stops due to frame skipping.
am clueless!!
only thing I can think of right now is that my new monitor, the TVLogic 58 needs more process power than my old one the TVLogic 56. Is that possible? Without HDMI no problem at all!
Am I right here in this forum by the way?!?
What is canon menu auto-shutoff set to?
it is set to off!
is this time can be remove boot flag from 5D3?
Bec i wnat to use the eye-fi card... just want to know if i remove the ML completely.
@a1ex: Has the ML overlay support when mirroring on an external monitor been addressed in the nightly build yet? Last I heard was from a couple of weeks ago (Post 675 on page 27).
I am getting the same orange horizontal lines as the image shown here:
https://bitbucket.org/hudson/magic-lantern/pull-request/521/mirroring-support-for-external-monitors/diff
Quote from: Frankie on July 30, 2014, 05:05:22 PM
is this time can be remove boot flag from 5D3?
Read first post of this thread.
Quote from: achangsta on July 30, 2014, 05:07:00 PM
@a1ex: Has the ML overlay support when mirroring on an external monitor been addressed in the nightly build yet? Last I heard was from a couple of weeks ago (Post 675 on page 27).
I am getting the same orange horizontal lines as the image shown here:
https://bitbucket.org/hudson/magic-lantern/pull-request/521/mirroring-support-for-external-monitors/diff
I'm pretty sure it has not since I just installed the latest build (as of a couple days ago) and orange banding is still there. Maybe I should use this as an opportunity to actually attempt to learn this whole build system.
Ok, I just built the 5D3.123 branch :)
Now to figure out what I did and how to make it useful!
In case I can't figure this out before someone can answer it for me...
After building ML, is there an easy way to package everything to put on the card to run it? If not, what files do I need to use from the build I did? I'm assuming the following three files at a minimum? Are there any more? Do I just use all the rest of the files from the nightly build?
(I checked out the 5D3-123 branch, made the code changes that a1ex noted as being under review for the external monitor, and compiled)
autoexec.bin
ML5D3123.FIR
ML/modules/5D3_123.sym
Also, do I need to reinstall the FW on the camera through the menu or anything? There's probably a simple link someone will end up pointing me to that covers "after you build it, this is how you deploy it", but I haven't found it yet
EDIT: It looks like changing to the correct platform directory and running 'make zip' is the step I was looking for.
Hello, I discovered that when I press garbage (delete) button during rec,
the borders top and above become transparent.
It should be really nice to have it always to prevent microphone or anything entering in the frame .. too late..
I would like to know if it could be possible to assign the magic zoom button during rec to à right button (af-on should be perfect) as we often focus with left hand.
I love ML and can't work without anymore.
Sincerely
Yvan
Quote from: yvan on July 31, 2014, 12:41:24 AM
Hello, I discovered that when I press garbage (delete) button during rec,
the borders top and above become transparent.
It should be really nice to have it always to prevent microphone or anything entering in the frame .. too late..
I would like to know if it could be possible to assign the magic zoom button during rec to à right button (af-on should be perfect) as we often focus with left hand.
I love ML and can't work without anymore.
Sincerely
Yvan
Anything else? A burger, coke?
Sorry budafilms but I think transparency borders and zoom assign button are real enhancements. I say that for contribution (as I also donate regurlarly).
QuoteAnything else? A burger, coke?
Also, I'm sorry to tell you I really prefer organic than the sh... you propose me. >:(
Sincerely.
http://articles.mercola.com/sites/articles/archive/2010/11/08/do-you-have-any-idea-of-the-chemicals-used-in-fast-food-chicken.aspx
hey everbody.
i have updated my camera with firmwar 1.2.3 and ML is runnung perfect.
the only problem is i need to record 1 hour in one peace and the camera shuts down after 29:56 minutes .does anybody know how i can solve this problem?
you guys are doing a brillant job on ML.thx for that.
Quote from: 4uAllIn on July 31, 2014, 11:39:03 AM
hey everbody.
i have updated my camera with firmwar 1.2.3 and ML is runnung perfect.
the only problem is i need to record 1 hour in one peace and the camera shuts down after 29:56 minutes .does anybody know how i can solve this problem?
you guys are doing a brillant job on ML.thx for that.
Get another 5D next to the one you already have, and push record once the first one has reached 29,56
Come on!!!!!!! :D
Ok, I got my build installed and tested the HDMI Mirroring change. It works!
I learned a few things while doing this. What *I* actually wanted fixed already works in the current nightly build. I think some others may be confused about it as well.
What was broken:
Setting "HDMI output + LCD" to "Mirroring" doesn't output anything to the external monitor in the nightly build. The change I tested fixes this. (This mode is supposed to be used for external recording where clean HDMI with NO OVERLAYS will be displayed on an external monitor)
What is not broken that I thought was broken:
Setting "HDMI output + LCD" to "No mirroring" showed a bunch of orange banding on the external monitor when global draw is on. I actually thought that was what this change fixed, but it already works! You just have to go to the Canon menu and change the setting "HDMI frame rate" from AUTO to "24p". (This is the mode WITH overlays. It is already working in the current nightly builds when you change the settings as I just described)
Quote from: 4uAllIn on July 31, 2014, 11:39:03 AM
hey everbody.
i have updated my camera with firmwar 1.2.3 and ML is runnung perfect.
the only problem is i need to record 1 hour in one peace and the camera shuts down after 29:56 minutes .does anybody know how i can solve this problem?
you guys are doing a brillant job on ML.thx for that.
There is a setting that's called sticky shutter witch prevents live view from shutdown after 29:59.
Quote from: yvan on July 31, 2014, 09:08:01 AM
Sorry budafilms but I think transparency borders and zoom assign button are real enhancements. I say that for contribution (as I also donate regurlarly).Also, I'm sorry to tell you I really prefer organic than the sh... you propose me. >:(
Sincerely.
http://articles.mercola.com/sites/articles/archive/2010/11/08/do-you-have-any-idea-of-the-chemicals-used-in-fast-food-chicken.aspx
Yeah! Was a Joke!
Try to find here a way to set your button preferences.
You can select one and put - like pressing RATE - ISO and WB ;)
Quote from: yvan on July 31, 2014, 12:41:24 AM
Hello, I discovered that when I press garbage (delete) button during rec,
the borders top and above become transparent.
It should be really nice to have it always to prevent microphone or anything entering in the frame .. too late..
I would like to know if it could be possible to assign the magic zoom button during rec to à right button (af-on should be perfect) as we often focus with left hand.
I love ML and can't work without anymore.
Sincerely
Yvan
Go into Canon settings, Custom Controls, and set the SET button to the ZOOM function. For transparent borders, would using the cropmarks here work? (or make your own in Paint): http://www.sawomedia.de/magiclantern/cropmarks/ (CineSco3 and CineSco5)
Quote from: TTGator on July 31, 2014, 10:30:59 PM
Ok, I got my build installed and tested the HDMI Mirroring change. It works!
I learned a few things while doing this. What *I* actually wanted fixed already works in the current nightly build. I think some others may be confused about it as well.
What was broken:
Setting "HDMI output + LCD" to "Mirroring" doesn't output anything to the external monitor in the nightly build. The change I tested fixes this.
What is not broken that I thought was broken:
Setting "HDMI output + LCD" to "No mirroring" showed a bunch of orange banding on the external monitor when global draw is on. I actually thought that was what this change fixed, but it already works! You just have to go to the Canon menu and change the setting "HDMI frame rate" from AUTO to "24p".
Can you share? Being able to output ML overlays to hdmi would be rad.
Quote from: Markus on August 01, 2014, 01:27:56 AM
There is a setting that's called sticky shutter witch prevents live view from shutdown after 29:59.
hey markus thx for your help.
the only problem is now that i can t find the sticky shutter button.
could you please help me and give me directions where i can find it?
thx a lot
Quote from: dubzeebass on August 01, 2014, 06:53:59 AM
Can you share? Being able to output ML overlays to hdmi would be rad.
I was trying to say (apparently not well) that it's already there! Just set "HDMI frame rate" to 24p and "HDMI output + LCD" to No mirroring.
I edited my original post that you quoted to try to make the difference between the two modes clearer.
Quote from: TTGator on August 01, 2014, 04:34:30 PM
I was trying to say (apparently not well) that it's already there! Just set "HDMI frame rate" to 24p and "HDMI output + LCD" to No mirroring.
I edited my original post that you quoted to try to make the difference between the two modes clearer.
Yeah but it would be nice to have a version where al the ML overlays are shown at the internal monitor while the external one has a clean output.
Quote from: Markus on August 01, 2014, 01:27:56 AM
There is a setting that's called sticky shutter witch prevents live view from shutdown after 29:59.
does anybody know where i can find the sticky shutter option?
thx in advance for your help and your great work to you all
Quote from: komeet on August 01, 2014, 06:09:40 PM
Yeah but it would be nice to have a version where al the ML overlays are shown at the internal monitor while the external one has a clean output.
Ah good point. Do any cameras have this working currently with ML?
Quote from: TTGator on August 01, 2014, 06:45:51 PM
Ah good point. Do any cameras have this working currently with ML?
not sure about any other cameras but how does your build behave? does it show the ML overlays on the camera while the external monitor is connected and hdmi output is set to mirroring?
Quote from: komeet on August 02, 2014, 01:20:54 PM
not sure about any other cameras but how does your build behave? does it show the ML overlays on the camera while the external monitor is connected and hdmi output is set to mirroring?
Yeah, actually that's exactly what it does. :P Had to go back and check.
No-mirroring only shows external monitor with overlays and the camera display is not used.
Quote from: TTGator on August 02, 2014, 02:11:28 PM
Yeah, actually that's exactly what it does. :P Had to go back and check.
No-mirroring only shows external monitor with overlays and the camera display is not used.
Could you share your version? :)
Quote from: komeet on August 02, 2014, 07:55:44 PM
Could you share your version? :)
Give this link a try...
https://www.dropbox.com/sh/qlsin98mx5exde5/AACgJHocDzIjIeEr2BEFrIBga (https://www.dropbox.com/sh/qlsin98mx5exde5/AACgJHocDzIjIeEr2BEFrIBga)
And of course, at your own risk yadda yadda
Quote from: TTGator on August 03, 2014, 04:33:03 PM
Give this link a try...
https://www.dropbox.com/sh/qlsin98mx5exde5/AACgJHocDzIjIeEr2BEFrIBga (https://www.dropbox.com/sh/qlsin98mx5exde5/AACgJHocDzIjIeEr2BEFrIBga)
And of course, at your own risk yadda yadda
thanks for the link.
I just checked it out and it works perfectly. ML overlays on the back of the camera and clean output on external monitor. Just awesome. Would be very nice to see this integrated into the nightlies! :)
Quote from: TTGator on August 03, 2014, 04:33:03 PM
Give this link a try...
https://www.dropbox.com/sh/qlsin98mx5exde5/AACgJHocDzIjIeEr2BEFrIBga (https://www.dropbox.com/sh/qlsin98mx5exde5/AACgJHocDzIjIeEr2BEFrIBga)
And of course, at your own risk yadda yadda
I will try, too.
Thanks!
Quote from: TTGator on August 03, 2014, 04:33:03 PM
Give this link a try...
https://www.dropbox.com/sh/qlsin98mx5exde5/AACgJHocDzIjIeEr2BEFrIBga (https://www.dropbox.com/sh/qlsin98mx5exde5/AACgJHocDzIjIeEr2BEFrIBga)
And of course, at your own risk yadda yadda
I'll check this as soon as I can. Thanks for the hard work! From your tweaking, is there any way to select where the Magic Lantern overlays are displayed? For Example:
ML Overlays on: Camera
Monitor
Both
This would be amazing!
Quote from: achangsta on August 05, 2014, 09:26:59 AM
I'll check this as soon as I can. Thanks for the hard work! From your tweaking, is there any way to select where the Magic Lantern overlays are displayed? For Example:
ML Overlays on: Camera
Monitor
Both
This would be amazing!
Yes, would be!
And the next set: 2.5K RAW and I will do a tattoo in my arm with the the letters: A1ex ;D
First two rounds of HDMI fixes will be in the next nightly build. It's not perfect, but at least it's a bit better than "totally broken".
Don't expect miracles.
Quote from: achangsta on August 05, 2014, 09:26:59 AM
I'll check this as soon as I can. Thanks for the hard work! From your tweaking, is there any way to select where the Magic Lantern overlays are displayed? For Example:
ML Overlays on: Camera
Monitor
Both
This would be amazing!
Yeah, I thought about that as well. Would be nice to be able to have it on both, but I thought it would need to be configurable because when people are using the monitor, they USUALLY won't be looking at the camera. If it were on the camera all the time it would be wasting a lot of battery when it's not wanted. So maybe I can try to understand the code that I built and see if there's a way to do that.
I'm not sure it's possible to have overlays on both monitors - there is only one BMP overlay as far as could tell, but there are two LV YUV buffers (each one with its own size).
Not to mention the code complexity required for that.
I wonder if anyone has problems with audio delay in ml files. I discovered that the sound is not synchronized in my recordings.
Raw recording is discussed here: http://www.magiclantern.fm/forum/index.php?board=49.0
(don't forget to check the first post before replying)
Hi Guys
I've been wanting to try Magic Lantern for a while. The only thing holding me back was not being able to uninstall completely.
Just wanted to know if that problem has been solved for the 5D Mark III. If so I will give it a whirl and definitely contribute feedback.
Also, when downgrading to the old firmware, is there still that horrible sleep lag that people were referring to in the past?
thanks
Hi Everyone,
I am really green here and I have a 5d m3. I am not a programmer or have any knowledge to do my own coding. I see on the main page that the most recent stable build is now 2 years old and does not list m3 as compatible. My question is, should I wait for a stable build that lists the m3 or can I safely install the latest nightly build. I realize that I make the final decision and accept all responsibility but would love some guidance.
I saw a post asking about the issue of not being able to completely uninstall. What impact will this have if I take out the card and want to use the Canon firmware afterwards.
Don't wait for official stable release, else you may never install. The nighties are very stable, sometimes minor glitch, but fixed quickly.
No problem on complete ML uninstall including boot flag :)
Thank you JimmyD30, I will download directly. I guess then I should log in regularly and get the newest nightly?
I have been reading the install guide and I would like to confirm that I need to install V2.3 first and then install the nightly build. This should not be a problem even though 2.3 does not list M3 as a compatible camera?
Do I need to downgrade my canon firmware, install 2.3, upgrade firmware, upgrade ML?
Quote from: a1ex on March 16, 2014, 03:26:45 PM
Installation:
1) Format the card from the camera.
2) Make sure you are running Canon firmware 1.2.3 (http://www.canon-europe.com/Support/Consumer_Products/products/cameras/Digital_SLR/EOS_5D_Mark_III.aspx?type=download&page=1).
3) Copy ML files (http://builds.magiclantern.fm/) on the card and run Firmware Update.
Uninstallation:
1) Run Firmware Update from your ML card.
2) Follow the instructions.
Quote from: Audionut on August 07, 2014, 03:38:01 AM
Just follow the instructions from Audionut, it's very simple:
INSTALLATION OF MAGIC LANTERN
1. Make sure your Canon Mark iii has the latest firmware 1.2.3 installed.
2. Take out CF card from camera.
3. Format SD card and download Magic Lantern files builds.magiclantern.fm/#/ (http://builds.magiclantern.fm/#/)
4. Select platform from drop down '5D3.123'.
5. Unzip the file 'magiclantern-Nightly and copy the unzipped folder contents 'autoexec.bin', 'ML' and 'ML5D3123.FIR' to the SD card.
6. Run the Firmware Update from Canon's menu.
7. After restart insert CF card and press trash can symbol to open Magic Lantern interface allowing a moment for installation.
8. Go to the Modules section in the ML interface and check these fields 'file_man', mlv_play', mlv_rec', mlv_snd' and then restart your camera.
9. The camera will now shoot Raw footage using the mlv codec.
Quote from: 4uAllIn on August 01, 2014, 06:33:14 PM
does anybody know where i can find the sticky shutter option?
thx in advance for your help and your great work to you all
Go to the wrench icon (Prefs.) Then under Misc key settings enable sticky HalfShutter.
Then press half shutter button halfway down before recording this will prevent the camera from thinking it's idle.
no guarantee. install it on your own risk. Nobody is gonna repair your camera.
Quote from: drybsmt on August 07, 2014, 12:38:03 AM
Hi Everyone,
I am really green here and I have a 5d m3. I am not a programmer or have any knowledge to do my own coding. I see on the main page that the most recent stable build is now 2 years old and does not list m3 as compatible. My question is, should I wait for a stable build that lists the m3 or can I safely install the latest nightly build. I realize that I make the final decision and accept all responsibility but would love some guidance.
I saw a post asking about the issue of not being able to completely uninstall. What impact will this have if I take out the card and want to use the Canon firmware afterwards.
I'm using magiclantern-Nightly.2014Aug07.5D3123 and I've noticed an odd problem with my camera. It refuses to turn itself on for short periods. After turning on/off opening the battery door, changing batteries, it will restart. This happens after I have left my camera for a while. Sorry I can't be more precise in what causes it and what "fixes" it.
At first I had just assumed that my battery had run flat. This happened several times today so I thought that ML was draining the battery. No. The battery was fine. 80% charged.
I have reverted to standard Canon 1.2.3 firmware and it's all OK.
Jack
Quote from: a1ex on August 06, 2014, 12:55:55 PM
First two rounds of HDMI fixes will be in the next nightly build. It's not perfect, but at least it's a bit better than "totally broken".
Don't expect miracles.
HUGE thank you for implementing HDMI monitor support in current build > magiclantern-Nightly.2014Aug07.5D3123
I'm using Zacuto EVF monitor in non-mirrored mode to give me display that I'm used to having on rear LCD, enabling me remote framing with ML menu that is scaled correctly on the EVF.
The Zacuto has 5d3 camera scale preset that gets it displaying properly once the ML display aspect is set to 16x9TB display.
For me this is a very welcome breakthrough, as now (with this monitor at least) - the EVF can be positioned anywhere, while still giving all the familiar ML display and correct frame line scaling.
Great work A1ex and all supporting code wizards!
Quote from: jimmyD30 on August 07, 2014, 01:00:36 AM
Don't wait for official stable release, else you may never install. The nighties are very stable, sometimes minor glitch, but fixed quickly.
No problem on complete ML uninstall including boot flag :)
Thanks Jimmy. Will give it a whirl once I wrap my project up next week. Thanks to all the dev guys for finally cracking that nut. 8)
Quote from: Hans_Punk on August 08, 2014, 01:11:54 AM
HUGE thank you for implementing HDMI monitor support in current build > magiclantern-Nightly.2014Aug07.5D3123
I'm using Zacuto EVF monitor in non-mirrored mode to give me display that I'm used to having on rear LCD, enabling me remote framing with ML menu that is scaled correctly on the EVF.
The Zacuto has 5d3 camera scale preset that gets it displaying properly once the ML display aspect is set to 16x9TB display.
For me this is a very welcome breakthrough, as now (with this monitor at least) - the EVF can be positioned anywhere, while still giving all the familiar ML display and correct frame line scaling.
Great work A1ex and all supporting code wizards!
Yes this is great, works for me too =). But I have to choose 3:2 t/b for alignment on my Zacuto EVF. You sure about 16:9?
BUILD 08/08
HDMI works perfect! and automatic when you turn camera ON.
Mirror: ML in LCD (Fantastic!) and Full Screen in LED Monitor FULL HD.
No Mirror: ML in the Monitor. BLack in LCD.
Continous recording MLV 1920x1080 25P (Computerbay 64 1000x) Global Draw ON.
1 Minute Recording MLV 1920x1154 25P
- No references BARS when you press REC (Is this correct?).
- MLV PLAY: black screen with the name of files and frames counting (Bug?).
The best build up to date for me!
Congrats!
Quote from: Markus on August 07, 2014, 03:25:13 PM
Go to the wrench icon (Prefs.) Then under Misc key settings enable sticky HalfShutter.
Then press half shutter button halfway down before recording this will prevent the camera from thinking it's idle.
Does not work - at least for me :-\
Quote from: Markus on August 08, 2014, 03:29:45 AM
Yes this is great, works for me too =). But I have to choose 3:2 t/b for alignment on my Zacuto EVF. You sure about 16:9?
That is what seems to work best for me...16x9 t/b and the Zacuto camera scale preset set to 5d3.
I'm using non-mirrored, as I prefer just to have all the menu/frame lines all within the EVF display.
Hi,
I am new to all this and want to try this with my Canon 5D mark iii.
One question. How do I unzip the file downloaded file? I am using Windows 7 and it does not recognise the zip file. The error comes up as, "Windows cannot open the folder. The compressed (zipped) folder is invalid". I have also tried right-clicking on the zipped file and selecting "Extract here". And I have tried WinRAR (v 4.20 (64-bit) which gives me the error "Unexpected end of archive".
Help?! :-)
Download again.
Does Dual ISO build for 5D3.123? Maybe I have a build environment problem?
Building module dual_iso...
REBUILDING
[ README ] module_strings.h
[ CC ] dual_iso.o
[ MODULE ] dual_iso.mo
[ STRIP ] dual_iso.mo
[ EXPORTS ] dual_iso.sym
0000136c dual_iso_calc_dr_improvement
000013c4 dual_iso_set_enabled
000013e4 dual_iso_is_enabled
000013f4 dual_iso_is_active
00001414 dual_iso_get_dr_improvement
00001594 dual_iso_get_recovery_iso
000015b4 dual_iso_set_recovery_iso
[ DEPENDS ] dual_iso.dep
Will load on:
1100D, 500D, 50D, 550D, 5D2, 5D3.123, 600D, 60D, 650D, 6D, 700D, 7D, EOSM
Not checked (compile ML for these cameras first):
5D3.113
[ gcc ] cr2hdr
clang: error: unknown argument: '-mno-ms-bitfields' [-Wunused-command-line-argument-hard-error-in-future]
clang: note: this will be a hard error (cannot be downgraded to a warning) in the future
make[3]: *** [cr2hdr] Error 1
********************************************************
WARNING: module dual_iso failed to build, deleting
********************************************************
[ RM ] dual_iso.o dual_iso.mo dual_iso.sym dual_iso.dep module_strings.h *.o *.d *.dep *.sym hgstamp
[ RM ] cr2hdr cr2hdr.exe
EDIT: Nevermind, found the answer. http://www.magiclantern.fm/forum/index.php?topic=11102.msg107950#msg107950 Maybe we can just remove that option from the Makefile permanently?
I am installed and running but the firmware upgrade scratched my lens. Who's going to pay for it? ;D I look forward to learning all the intricacies and benefiting from everyone's experience.
I'm currently running ML on 5D Mark III FIRMWARE Version 1.1.3. If I were to upgrade to firmware 1.2.3 and use ML on it. Would I just have reformat my card that is running ML on the 1.1.3 firmware through computer and follow the steps at the beginning of this page?
Firs upgrade firmware from canon!
After, copy builds 1.2.3 in your card, put in the camera and follow the instruction form thread.
Can anyone help me unzip the zip file? I have downloaded it multiple times and even tried older versions but with the same errors as per my previous post.
Your help would be appreciated.
Maybe try unzipping in another computer? I've downloaded the latest version and several others and always worked fine. Maybe trying another software to do it?
thx alot for the hdmi fix..mirroring mode works great with the lilliput
Hey friends,
I'm hoping you good people would be kind enough to help me with an issue i'm having with my 5D MARK iii.
Ever since I got my camera I've been getting these terrible flickering on all my shots(after installing magic lantern) And I cannot figure out why. I first downgraded to 1.1.3, had flickering, then upgraded to 1.2.3 and still flickering occurs in my videos. PLEASE HELP, PPLLEEAASSEE!!
Here is a footage of what i'm talking about
http://youtu.be/miU4JrG5Ks4
Quote from: itsDPmikey on August 10, 2014, 06:47:11 AM
Hey friends,
I'm hoping you good people would be kind enough to help me with an issue i'm having with my 5D MARK iii.
Ever since I got my camera I've been getting these terrible flickering on all my shots(after installing magic lantern) And I cannot figure out why. I first downgraded to 1.1.3, had flickering, then upgraded to 1.2.3 and still flickering occurs in my videos. PLEASE HELP, PPLLEEAASSEE!!
Here is a footage of what i'm talking about
http://youtu.be/miU4JrG5Ks4
It's terrible!
I think you have drop frames, not flickering.
Wich Card do you use? Build?
Have you tried with a lower size, like 1280x720?
Quote from: budafilms on August 10, 2014, 07:12:14 AM
It's terrible!
I think you have drop frames, not flickering.
Wich Card do you use? Build?
Have you tried with a lower size, like 1280x720?
THANK YOU FOR RESPONDING BUDAFILMS
No I have not used a lower Res, I will do that immediately. If it is the card, is there a card that can do 1920? Or a way around it for the card that I have like maybe turning some of the other unnecessary options/settings off so the card can handle 1920?
I am using a 1066x 32GB UDMA 7 lexar professional CF
Max. Read Speed 160 MB/s
Max. Write Speed 155 MB/s
I don't understand, In the ML settings it says for 1920 you need a card that can record 82.9MB/s and this card obviously is capable of that or atleast thats what lexar/B&H states.
Hi all,
What software do you use to unzip the ML file? I have tried native Windows 7 (64 bit) and also WinRAR v4.2, but neither work and come up with errors (see my previous posts up this page.
Your assistance would be greatly appreciated as I have never had any problems with unzipping files.
Thanks!
Download statistics by a1ex:
As far as I'm aware of you are the first person having issues.
Ciao
Walter
Quote from: davdav on August 10, 2014, 09:28:15 AM
Hi all,
What software do you use to unzip the ML file? I have tried native Windows 7 (64 bit) and also WinRAR v4.2, but neither work and come up with errors (see my previous posts up this page.
Your assistance would be greatly appreciated as I have never had any problems with unzipping files.
Thanks!
You have problem in your machine. Maybe some kind of antivirus or firewall.
I downloaded lot of times.
Quote from: budafilms on August 10, 2014, 07:12:14 AM
It's terrible!
I think you have drop frames, not flickering.
Wich Card do you use? Build?
Have you tried with a lower size, like 1280x720?
BUDAFILMS, I just remembered that my settings are set to stop recording if frame skips/drops
so I guess its not dropped frames.
ok so here is what I did so far, I recorded about 20 seconds of the following below
1920 RAW
720 RAW
1920 MLV RAW
720 MLV RAW
1920 RAW gd off
in all these cases NONE OF THEM dropped frames or flickered. I got them all in each on its own timeline in DAVINCI RESOLVE 10 and watched them in "BMD Film" mode (23.976) as normal and they all looked fine UNTIL I started color grade them, all of the sudden playback starts flickering/frame skipping. VERY BAZZARE. So I reset the colors back to washed out raw and hit play it stopped flickering/skipping.
I took these footages in photoshop camerraw and color graded the footage and hit playback and WALLA NO flickering or skipping. So whats going on here with davinci Resolve and these DNG files?
any ideas guys?
Hey guys,
I recently installed the nightly build from July the 30th and after that I keep getting corrupted raw photos out of my 5D mk III even after deinstalling Magic lantern.
They look like this: https://www.dropbox.com/s/m7fpfi9otrgj89c/8U3A0769.jpg
So not all pictures are corrupted. Like 2 out of 10 are perfectly fine. My question is wether that is a known problem and how I can fix it. The embedded JPEGs from the raw photos are perfectly fine. The raw itself is corrupted. Because of this I don't think that the sensor is broken.
I deinstalled Magic lantern through the firmware update process and took the photo in the link above. Still corrupted. I uploaded the raw version of the photo too, so you can see for yourself: https://www.dropbox.com/s/wgucqrl2pidj9q4/8U3A0769.CR2
The recorded raw videos were perfectly fine, without any corruption at all.
Thx in advance for every helpful answer
Quote from: itsDPmikey on August 10, 2014, 10:27:15 AM
BUDAFILMS, I just remembered that my settings are set to stop recording if frame skips/drops
so I guess its not dropped frames.
ok so here is what I did so far, I recorded about 20 seconds of the following below
1920 RAW
720 RAW
1920 MLV RAW
720 MLV RAW
1920 RAW gd off
in all these cases NONE OF THEM dropped frames or flickered. I got them all in each on its own timeline in DAVINCI RESOLVE 10 and watched them in "BMD Film" mode (23.976) as normal and they all looked fine UNTIL I started color grade them, all of the sudden playback starts flickering/frame skipping. VERY BAZZARE. So I reset the colors back to washed out raw and hit play it stopped flickering/skipping.
I took these footages in photoshop camerraw and color graded the footage and hit playback and WALLA NO flickering or skipping. So whats going on here with davinci Resolve and these DNG files?
any ideas guys?
The only Idea before a Dev analysing your RAW file, it's about your discrete graphic card or your timeline fps setting.
The DNG's extracted for ACR and DaVINCI are the same, and as you say it's just a problem with Resolve.
I only use Resolve and with the last build and the lats before I don't have any problem like that.
Quote from: Jazzepisode on August 10, 2014, 11:05:03 AM
Hey guys,
I recently installed the nightly build from July the 30th and after that I keep getting corrupted raw photos out of my 5D mk III even after deinstalling Magic lantern.
They look like this: https://www.dropbox.com/s/m7fpfi9otrgj89c/8U3A0769.jpg
So not all pictures are corrupted. Like 2 out of 10 are perfectly fine. My question is wether that is a known problem and how I can fix it. The embedded JPEGs from the raw photos are perfectly fine. The raw itself is corrupted. Because of this I don't think that the sensor is broken.
I deinstalled Magic lantern through the firmware update process and took the photo in the link above. Still corrupted. I uploaded the raw version of the photo too, so you can see for yourself: https://www.dropbox.com/s/wgucqrl2pidj9q4/8U3A0769.CR2
The recorded raw videos were perfectly fine, without any corruption at all.
Thx in advance for every helpful answer
Are you compiling Silent Module or just the BUILD like downloaded?
Have you tried with Build 08/08?
Quote from: budafilms on August 10, 2014, 11:21:14 AM
Are you compiling Silent Module or just the BUILD like downloaded?
Have you tried with Build 08/08?
I just downloaded the build and put it on the card.
Yes I tried that, nothing better. But even after deinstalling ML I keep getting corrupted frames. I'm a little worried that I might have killed something.
Whenever I take JPGs they're just fine. Like you would expect. But when shooting raw, these weird issues appear.
where did you buy the card? ebay?
Quote from: itsDPmikey on August 10, 2014, 07:19:13 AM
THANK YOU FOR RESPONDING BUDAFILMS
No I have not used a lower Res, I will do that immediately. If it is the card, is there a card that can do 1920? Or a way around it for the card that I have like maybe turning some of the other unnecessary options/settings off so the card can handle 1920?
I am using a 1066x 32GB UDMA 7 lexar professional CF
Max. Read Speed 160 MB/s
Max. Write Speed 155 MB/s
I don't understand, In the ML settings it says for 1920 you need a card that can record 82.9MB/s and this card obviously is capable of that or atleast thats what lexar/B&H states.
did you think about getting camcorder? ML is tricky and takes a lot of reading!
Quote from: itsDPmikey on August 10, 2014, 06:47:11 AM
Hey friends,
I'm hoping you good people would be kind enough to help me with an issue i'm having with my 5D MARK iii.
Ever since I got my camera I've been getting these terrible flickering on all my shots(after installing magic lantern) And I cannot figure out why. I first downgraded to 1.1.3, had flickering, then upgraded to 1.2.3 and still flickering occurs in my videos. PLEASE HELP, PPLLEEAASSEE!!
Here is a footage of what i'm talking about
http://youtu.be/miU4JrG5Ks4
Quote from: itsDPmikey on August 10, 2014, 07:19:13 AM
I don't understand, In the ML settings it says for 1920 you need a card that can record 82.9MB/s and this card obviously is capable of that or atleast thats what lexar/B&H states.
Run a Card Benchmark those numbers stated by B&H/Lexar mean nothing...
What software do you use to unzip the ML file?? I'm on Windows 7 64 bit.
@Davdav: Literally thousands of Mac and PC users didn't have any problems unzipping ML files like you have. No matter which program is used ...
It is a pretty simple task to unzip ML contents. No features included which may cause troubles.
The problem must be related to your PC. After downloading the file, disconnect from the net, disable all additional firewall software, internet protection, virus scan and reboot. Then try to extract the files again.
Results? (After enabling all the protection stuff and reconnecting to the net, of course)
EDIT: You may want to download something like "MD5 File Hasher" and check if the checksum fits.
3c9eaa95c945fb73adc88571ab010eb4 magiclantern-Nightly.2014Aug07.5D3123.zip
Or you need space on your hard drive. You know, like half the hard drive size. Just saying.
To extract 1.6 MByte you have to stay below 50 percent disk usage? Let's say you are kidding, okay?
Quote from: budafilms on August 10, 2014, 11:18:45 AM
The only Idea before a Dev analysing your RAW file, it's about your discrete graphic card or your timeline fps setting.
The DNG's extracted for ACR and DaVINCI are the same, and as you say it's just a problem with Resolve.
I only use Resolve and with the last build and the lats before I don't have any problem like that.
Yeah it is definitely a davinci resolve issue. I typed in davinci RAw file flickering/frame skipping and I FOUND a bunch of people with same issue. So I'll have to deal with it by grading them in somewhere else other than davinci, sucks because I was just getting the hang of davinci. Well, I rather have a broken davinci than a broken camera so its all good.
Quote from: vovkinson on August 10, 2014, 02:33:25 PM
where did you buy the card? ebay?
No I bought the card from B&H.
Quote from: Stedda on August 10, 2014, 02:39:47 PM
Run a Card Benchmark those numbers stated by B&H/Lexar mean nothing...
the card is good, its Davinci Resolve. Found a bunch of forums on the same issue. I was watching some footages in my Premiere pro project. Some of my videos aren't flickering and some later ones(in the same project) are. So I was confused at first what was the difference between the earlier footages and the later ones. Ah I realized I graded them in 2 different places. Earlier ones in CameraRaw and later ones(flickering ones) in Davinci. A lightbulb went on and I did some more tests and walla it is Davinci causing the issue. So I uninstalled Davinci completely and used aftereffects and some extra plugins like red giant. I will probably get Davinci Resolve sometime in the future and I hope by then the v11 will work properly. Btw I was using the v10.
A BIG THANKS TO ALL WHO RESPONDED AND TRIED TO HELP, THANK YOU AGAIN FRIENDS!
Quote from: Jazzepisode on August 10, 2014, 11:05:03 AM
Hey guys,
I recently installed the nightly build from July the 30th and after that I keep getting corrupted raw photos out of my 5D mk III even after deinstalling Magic lantern.
They look like this: https://www.dropbox.com/s/m7fpfi9otrgj89c/8U3A0769.jpg
So not all pictures are corrupted. Like 2 out of 10 are perfectly fine. My question is wether that is a known problem and how I can fix it. The embedded JPEGs from the raw photos are perfectly fine. The raw itself is corrupted. Because of this I don't think that the sensor is broken.
I deinstalled Magic lantern through the firmware update process and took the photo in the link above. Still corrupted. I uploaded the raw version of the photo too, so you can see for yourself: https://www.dropbox.com/s/wgucqrl2pidj9q4/8U3A0769.CR2
The recorded raw videos were perfectly fine, without any corruption at all.
Thx in advance for every helpful answer
So after uninstalling Magic lantern I downgraded to official canon firmware 1.1.3 testwise. After that all the raw problems were gone. I got normal raw photos, like they're supposed to be. Then I updated to official canon firmware 1.2.3 normally and the problems were present again. So that means I got raw photo problems on 1.2.3 after uninstalling ml but on 1.1.3 they're gone. I think, that something didn't get uninstalled properly. The problems are not present in 1.1.3 because they ly in some area, which got affected by the 1.2.3 update.
Anybody got a hint for me, which infos I could provide, to help me out here?
did you try another card?
Quote from: Jazzepisode on August 11, 2014, 12:19:43 PM
So after uninstalling Magic lantern I downgraded to official canon firmware 1.1.3 testwise. After that all the raw problems were gone. I got normal raw photos, like they're supposed to be. Then I updated to official canon firmware 1.2.3 normally and the problems were present again. So that means I got raw photo problems on 1.2.3 after uninstalling ml but on 1.1.3 they're gone. I think, that something didn't get uninstalled properly. The problems are not present in 1.1.3 because they ly in some area, which got affected by the 1.2.3 update.
Anybody got a hint for me, which infos I could provide, to help me out here?
I tried another card. At first the pictures were corrupted too. But after downgrading and upgrading again, my SD card works somehow. My CF card doesn't though. I'm currently trying to format it with my pc, but I keep getting errors...
Before installing ml the card was fine. Is that a known problem?
I would try to format your CF card in PC and in camera.
For now - remove your SD card from the camera and play with CF card only.
One thing at time.
Quote from: Jazzepisode on August 11, 2014, 01:25:08 PM
I tried another card. At first the pictures were corrupted too. But after downgrading and upgrading again, my SD card works somehow. My CF card doesn't though. I'm currently trying to format it with my pc, but I keep getting errors...
Before installing ml the card was fine. Is that a known problem?
Quote from: vovkinson on August 11, 2014, 01:51:08 PM
I would try to format your CF card in PC and in camera.
For now - remove your SD card from the camera and play with CF card only.
One thing at time.
I formatted the card in pc and camera multiple times. The frames stay corrupted. My other two cards work fine now. It seems like I killed my CF card. Sadly it was an expensive one Sandisk extreme pro 64gb 160 MB/s.
I tried deleting the partition and making a new one, formating to exfat from scratch. Same problem
The sort of corruption you're seeing is one I have experienced before. It is data corruption in the files themselves and doesn't necessarily indicate a camera or card problem at all. It can be due to a variety of reasons:
- Bad USB cables
- Bad USB card reader
- Bad USB port
- Damaged memory card
- HDD controller or HDD problems
- Faulty RAM on your PC
- Faulty camera
...and so on. Typically the corruption happens during the transfer from the card to computer, rather than on the camera itself. You can test this by reviewing the photos in the camera - if they look OK, and you can develop them in camera (using the 5D3 RAW development functionality), then it's easy to confirm the camera and card isn't the problem but actually the transfer process over to your PC. Conversely, if you see corruption on the camera without having involved the PC, then your camera and/or card is the problem.
I'd suggest trying different means of transferring photos to your PC (eg via USB from the camera itself rather than using a card reader, swapping USB ports and USB cables, copying to a different physical HDD etc) to try and narrow down the problem. Note also that you should NEVER use high speed UDMA 7 CF cards in a USB 2.0 reader - that can corrupt data on transfers, and in some cases even damage the CF card itself.
If you want to read more about this sort of corruption, there are various threads such as this one that might help: https://forums.adobe.com/thread/356898
Quote from: chris_overseas on August 11, 2014, 02:14:51 PM
The sort of corruption you're seeing is one I have experienced before. It is data corruption in the files themselves and doesn't necessarily indicate a camera or card problem at all. It can be due to a variety of reasons:
- Bad USB cables
- Bad USB card reader
- Bad USB port
- Damaged memory card
- HDD controller or HDD problems
- Faulty RAM on your PC
- Faulty camera
...and so on. Typically the corruption happens during the transfer from the card to computer, rather than on the camera itself. You can test this by reviewing the photos in the camera - if they look OK, and you can develop them in camera (using the 5D3 RAW development functionality), then it's easy to confirm the camera and card isn't the problem but actually the transfer process over to your PC. Conversely, if you see corruption on the camera without having involved the PC, then your camera and/or card is the problem.
I'd suggest trying different means of transferring photos to your PC (eg via USB from the camera itself rather than using a card reader, swapping USB ports and USB cables, copying to a different physical HDD etc) to try and narrow down the problem. Note also that you should NEVER use high speed UDMA 7 CF cards in a USB 2.0 reader - that can corrupt data on transfers, and in some cases even damage the CF card itself.
If you want to read more about this sort of corruption, there are various threads such as this one that might help: https://forums.adobe.com/thread/356898
Thank you so much. When I copied the files from the 'bad' card via camera cable, the picture files are ok. The card reader I used seems to be the problem, though the other card I have, which is the same, works just fine with it.
would you let us know what card reader you have so we won't buy it?
Quote from: Jazzepisode on August 11, 2014, 02:35:07 PM
Thank you so much. When I copied the files from the 'bad' card via camera cable, the picture files are ok. The card reader I used seems to be the problem, though the other card I have, which is the same, works just fine with it.
Friends, my new 5D MK III (Purchased only 3days ago) is ready. A Lexar 1066x 16GB CF is ready. Going to install the ML. Any tips?
Installed it. Running fine. :) But I have no CF Card Reader right now. Waiting for tomorrow to upload in the PC. Result- 1920 x 1080 Continuous. Happy with that. 1920 x 1280 650 not continuous.
Quote from: onlypapai on August 11, 2014, 06:34:34 PM
Installed it. Running fine. :) But I have no CF Card Reader right now. Waiting for tomorrow to upload in the PC. Result- 1920 x 1080 Continuous. Happy with that. 1920 x 1280 650 not continuous.
Congrats!
Get the CF Card Reader and do nice videos!
Thanks Budafilms. I have only 16GB :-[. Battery getting low. A lot more investment is waiting for me.
Quote from: vovkinson on August 11, 2014, 04:19:41 PM
would you let us know what card reader you have so we won't buy it?
I used the transcend usb 3.0 one: http://www.amazon.de/Transcend-All--Multi-Kartenleseger%C3%A4t-schwarz/dp/B0056TYRMW/ref=sr_1_1?ie=UTF8&qid=1407787200&sr=8-1&keywords=transcend+card+reader
Worked fine for me for over 3 months, but not any longer as you can see. I'm thinking about buying the lexar one, but we're getting of topic ;)
I have the transcend for more than 1 year and it's great! I use with CF, SD toquether. Any problem!
No, I have not formatted XFat. I'll try it today. I'm crippled as my Card Reader is not delivered. Anxiously waiting.
Does the camera temperature increase during RAW shoot? I feel a bit of heat from my cam.
Howdy
Hoping that A.This is the right thread and B.That someone can help.
I'm running the latest nightly build. My camera has started to stay in 'busy' mode if I attempt to take a photo after recording an mlv (ie. shutter won't release or if it does then last image it takes stays on live view and the camera no longer responds)
I can't recreate the problem every time but it is occurring frequently and sometimes when I just want to take photos, only in live view however. Has anyone had this problem before?
Hi,I noticed that the screen is trimed in external monitor when global draw is on.
the top some line is hidden by a black line.
Can I remove the black line and get full pixel?
REAR LCD
EXTERNAL LCD
5D3 1.2.3+MLNightly.2014Aug07.5D3123.zip,
I get that problem if I start my external lcd after I start the camera but if it's already up and running when I turn on the camera that never happens.
7/8/14 build , any idea why my iso is set to 160 but ML shows it as 200 , if i set 640 ML shows it as 800 ?
Quote from: jafa on August 14, 2014, 04:00:35 PM
7/8/14 build , any idea why my iso is set to 160 but ML shows it as 200 , if i set 640 ML shows it as 800 ?
When shooting raw you only get multiples of 100 (200,400,800,1600 etc.) Those in between iso modes are applyed as digital gain to the compressed h264 video files. So those in between modes are always based on one of the real iso values and does nothing to the raw stream that you grab and record when shooting raw.
Thanks for clearing that up Marcus :)
Quote from: Markus on August 14, 2014, 06:43:12 PM
When shooting raw you only get multiples of 100 (200,400,800,1600 etc.) Those in between iso modes are applyed as digital gain to the compressed h264 video files. So those in between modes are always based on one of the real iso values and does nothing to the raw stream that you grab and record when shooting raw.
Interesting!
And the ML EV? In the ML menu, has something over the real ISO?
Quote from: satotmp on August 14, 2014, 12:25:04 PM
Hi,I noticed that the screen is trimed in external monitor when global draw is on.
the top some line is hidden by a black line.
Can I remove the black line and get full pixel?
REAR LCD
https://dl.dropboxusercontent.com/u/5542662/ML/th_rearLCD.jpg
EXTERNAL LCD
https://dl.dropboxusercontent.com/u/5542662/ML/th_externalLCD.jpg
5D3 1.2.3+MLNightly.2014Aug07.5D3123.zip,
Try put Global Draw Off, not Allow.
I prefer Allow, for the margins.
Offtopic: Could you please stop using full quotes?
Hello,
is there a stable release to download somewhere or do i have to download a "nightly build" to get magiclantern on my mk3?
Top of page -> Downloads
====
Stable supported for
5D Mark ii 2.1.2
50D 1.0.9
60D 1.1.1
500D 1.1.1
550D 1.0.9
600D 1.0.2
===
Quote from: budafilms on August 15, 2014, 06:05:44 AM
Try put Global Draw Off, not Allow.
I prefer Allow, for the margins.
Thank you.
I got a solution.
When Cropmarks is on,the black line vanished.
So,I create a transparent bmp file.
bye
There was mention a little while ago about the ML Team finding a way to squeeze another stop or so of dynamic range out of the camera. Was this feature ever implemented and is there a way to utilize this on 1.2.3? I never heard about it rolling out or see any options to turn it on anywhere.
Dual ISO
http://www.magiclantern.fm/forum/index.php?topic=7139.0
0.8 EV here for 5D3: http://www.magiclantern.fm/forum/index.php?topic=10111.0
Off-topic discussion about basic raw post processing moved over here: http://www.magiclantern.fm/forum/index.php?topic=13044.0
Quote from: a1ex on May 12, 2014, 08:59:06 AM
RAW and MLV are not the core of ML, they are just applications (sure, very popular ones). There is a forum area dedicated to raw recording (http://www.magiclantern.fm/forum/index.php?board=49.0), so please discuss raw issues there.
I prefer this thread to be about core issues specific to 5D3 (in particular, problems introduced in 1.2.3 that did not exist in 1.1.3).
Before posting, it's a good idea to read at least the first and the last post from the thread.
Locking the thread for 1 month, and there will be no more updates on the 1.2.3 branch during this period.
Quote from: a1ex on May 12, 2014, 08:59:06 AM
RAW and MLV are not the core of ML, they are just applications (sure, very popular ones). There is a forum area dedicated to raw recording (http://www.magiclantern.fm/forum/index.php?board=49.0), so please discuss raw issues there.
I prefer this thread to be about core issues specific to 5D3 (in particular, problems introduced in 1.2.3 that did not exist in 1.1.3).
edit by Audionut:
Please also consider this message when the thread reopens.
http://www.magiclantern.fm/forum/index.php?topic=3072.msg126650#msg126650
Quote- encourage newcomers to post in the right forum (I've locked the 1.2.3 thread because it was flooded with offtopic questions about RAW/MLV)
Thread re-opened. Any messages about RAW/MLV from this thread will be deleted without notice.
Is anyone else having problems with exp comp EXIF data being tagged wrong since ML 1.2.3 install?
Since installing Magic Lantern 1.2.3 on 5D III, I have noticed that my files shot at 0 EV exposure comp are wrongly tagged as either +1/3 EV (seen in Digital Photo Professional) or "+1 Step" (in Windows Explorer window, flickr).
Files shot with +1/3 EV are wrongly tagged as +1/2 EV (DPP) and "+0.5 Step" in Windows explorer and "+1 EV" in flickr. A file shot with +2/3 EV actually showed as nonsense under flickr EXIF, "-1/2 EV"
Has anyone noticed similar problems since installing Magic Lantern 1.2.3. on 5D III? Any way to fix this or could this possibly be some other issue, although the only change has been Magic Lantern?
Below are examples:
Shot at 0 EV, tagged as +1/3 EV (DPP) or "+1 Step" (in Windows Explorer window, flickr).
(https://flic.kr/p/pknbAe)1)0EV (https://flic.kr/p/pknbAe) by drjlo1 (https://www.flickr.com/people/57834091@N07/), on Flickr
Shot at +1/3 EV, tagged as +1/2 EV (DPP) and "+0.5 Step" in Windows explorer and +1 EV in flickr.
(https://flic.kr/p/pkkpML)2)+0.33EV (https://flic.kr/p/pkkpML) by drjlo1 (https://www.flickr.com/people/57834091@N07/), on Flickr
For diagnostic reasons in would be fine to have access to the original file.
Can you zip it and upload it to a file hoster? Add Magic.cfg found in ML\Settings
And which ML version (build date) is used?
Can you reset Canon settings? There was a bug in ETTR, many months ago, which could have caused this.
OK, I've uploaded the zip with the 2 sample photo files and Magic.cfg.
Not sure where I can find the ML build date, but the date these ML files were installed on my camera appears to be 9/10/13.
<iframe src="https://onedrive.live.com/embed?cid=2D144F4239813ADE&resid=2D144F4239813ADE%211353&authkey=ACQ4PZFoKKQH518" width="165" height="128" frameborder="0" scrolling="no"></iframe>
What kind of "reset Canon settings" are we talking about to fix this?
Canon menu -> Clear camera settings.
OK, "clear all camera settings" worked to correct the EXIF bug. Thanks.
Is the embargo on updates to the 1,2.3 branch continuing? I know a1ex said there would be no new updates whilst this thread was locked...
I installed a newer version, made by mk11179 but there are some issues, so i think that there is no newer version before those problems are solved. (One thing i noticed is that with mlv - i have recorded at 5:3, there is one corrupt frame all 30 seconds - with some white lines in the bottom.) perhaps a buffering problem, i dont know. We have to und wait... Greets
Hi All,
First time ML user (or trying to be anyway). So I followed all instructions as far as I can tell.
-I updated my Canon firmware to 1.2.3.
-I downloaded the latest ML nightly build.
-I formatted my SD card again in camera.
-I extracted all contents to the root folder of my SD Card.
-I inserted said SD card and taken out my CF card.
-I installed the firmware update through the menu.
-Everything seemed to install fine.
-I waited the 30 seconds for the bootflag to be removed.
-As prompted, I restarted my camera (off, then on).
-When I turned it on, nothing seems different. I don't see any ML overlays, options, etc.
-I pressed the trash can, which also did nothing.
I am using a San Disk Extreme Pro 95MB/s 32GB SD Card and a Lexar 32GB 800x CF card.
PLEASE HELP! I must've missed something, but I have no idea what. I'm dying to try this out!
Oh, whoops. I guess you have to restart before the 30 seconds. Working now. =)
Quote from: lintoni on October 01, 2014, 04:39:31 AM
Is the embargo on updates to the 1,2.3 branch continuing? I know a1ex said there would be no new updates whilst this thread was locked...
I'll update the branch as soon as I'll finish tweaking the fullres silent pictures.
Currently having some network problems, so I'm mostly offline these days.
Quote from: a1ex on October 02, 2014, 01:27:34 PM
I'll update the branch as soon as I'll finish tweaking the fullres silent pictures.
Currently having some network problems, so I'm mostly offline these days.
Thanks for the info. I realise you have a lot of things to do, I was just a little concerned that the branch had become a victim of some Worthless complications, so it's a relief to know that that is not the case.
Just updated to firmware 1.2.3.. works fine here. Amazing. Thanks all to who contributed.
hello a1ex!
i dont want to be nuisance, but may i carefully ask when you will update the 5d mark3 123 nightly? the 113 nightly is updated all the time and the 123 branch is 2 month old..
thx swinxx
Keep an eye out here: https://bitbucket.org/hudson/magic-lantern/commits/all
I think most nightlies are compiled automatically each night, or at least whenever there are any commits. The 5D3.123 branch is only compiled when there is an specific 5D3.123 commit, and unless I have missed something, there haven't been any 5D3.123 specific commits for some time now.
Hint: this commit (https://bitbucket.org/hudson/magic-lantern/commits/76ea3223c7d1d38ecc97c1627ec70cd75f9a63c4), even though it says 5D3.123 in the name, is for the dm-spy module, which means the module needs to be updated, not the actual core 5D3.123 build.
But there are updates in the mlv and raw modules..? These are not specific, but also used by 5dmk3? No?
They're in a different branch: https://bitbucket.org/hudson/magic-lantern/branch/mlv_rec_lj92
Which means they're not meant to go in the nightly builds.
The only thing I see in the last month with a quick browse, is this: https://bitbucket.org/hudson/magic-lantern/commits/79e29eac86a785d2fc54be65dc5a2135abc8ab0c
where to download?
Downloads (top right hand of page) > look for Nightly Builds > select 5D3.123
Quote from: renli0413 on October 12, 2014, 03:48:21 AM
where to download?
Can ML only brick your camera during installation or at any time?
Quote from: Ssandman on October 13, 2014, 03:38:43 PM
Can ML only brick your camera during installation or at any time?
Every time someone asks a question like this an angel gets his wings ripped off.
Just a small hint for all 5D MK 3 op's:
I suddenly got only very low volume on the headphone output while filming and could not adjust it. Finally went into playmode and there and only there it is possible to adjust the volume. Changing the levels in ML-menu did nothing, even after setting the headphone levels in the playmode.
my two eurocents.. Matthias
Sorry for the newbie question, is there an Alpha build of ML for the 5D3 or are the Nightly downloads considered Alphas. I know there is no stable release yet. I don't mind not having the latest features, but I do need it as stable as possible so the nightly builds scare me.
Not sure if there was a solid Alpha or Beta release that had a solid rep for working well. Have a shoot in a week I wanted focus peaking for and maybe some other small features if available...not shooting RAW or anything just yet. But I can't afford corrupt files.
Also, what's the process of going back to the standard Canon firmware from ML? I didn't see that.
Thanks!
Top of page -> User Guide -> FAQ
Top of page -> Downloads
And do some web search for "Alpha". There is no such thing as "solid alpha". It's a contradiction.
Hi, My 5D MK3 is Running on "1.1.3 ML 2.3 NEXT " , What exactly i need to do in order to upgrade?
The instructions says :
1.Format the card from the camera. (Sd card that contains the ML program? or what?)
2.Make sure you are running Canon firmware 1.2.3. (How do i instal this version? via SD card? I just copy the file of this version and run the update? )
3) Copy ML files on the card and run Firmware Update. (Should i delete the second step's file[firmware] from the card before putting the ML files?)
Uninstallation:
1) Run Firmware Update from your ML card. (Means that if i want to go back to 1.2.3 Canon's, just put it on the card and run the update and then the ML is gone?)
2) Follow the instructions.( Are there any more instructions? Where are they?)
I'm asking all of this because i don't really don't know. Thank you.
Installation
1. Any SD card
2. Update Canon firmware as per Canon update process. Read the instructions that come with the Canon firmware file.
3. Might as well.
Uninstallation
1. Yes
2. 1 + wait 30 seconds.
So just making sure.
My Version is 1.1.3 ml 2.3 NEXT. So i just go and update the version by putting the update file (ML5D3123.FIR) in to my clean SD card or with ML on it? and run the firmware update?
I stressed out by this thats why i'm asking to make sure i'm doing it right :)
If you're going to put Magic Lantern 5D3.123 on your camera, it needs to be running Canon firmware version 1.2.3.
Your camera has Canon firmware 1.1.2, so you need to download the appropriate version from your local Canon website. If you're in the US, for instance, you would go to:
http://www.usa.canon.com/cusa/consumer/products/cameras/slr_cameras/eos_5d_mark_iii#DriversAndSoftware (http://www.usa.canon.com/cusa/consumer/products/cameras/slr_cameras/eos_5d_mark_iii#DriversAndSoftware)
Look for "Firmware" and you will find Canon's firmware update. It comes in OSX and Windows flavours, pick the appropriate one for you. Follow the instructions from Canon (included in the download) to update the firmware to 1.2.3.
THEN format your SD card in camera, then put it into your computer's card reader, extract the Magic Lantern files to the card, put it back in the camera, then update the firmware to include Magic Lantern.
Can I use this firmware in Canon 1D Mark IV for recording RAW video?
And please make firmware for Canon 1DMIV :(
Quote from: Abek on October 20, 2014, 07:24:14 PM
Can I use this firmware in Canon 1D Mark IV for recording RAW video?
And please make firmware for Canon 1DMIV :(
No.
Canon have made it clear that they do not want people modifying the firmware of their EOS1D series cameras, so if you to run Magic Lantern, you'll have to slum it and get a cheaper camera. :)
Canon is ...
Quote from: lintoni on October 20, 2014, 09:15:49 PM
Canon have made it clear that they do not want people modifying the firmware of their EOS1D series cameras, so if you to run Magic Lantern, you'll have to slum it and get a cheaper camera. :)
Further to this, see:
http://www.canonrumors.com/2013/01/inside-the-canon-eos-1d-c/ (http://www.canonrumors.com/2013/01/inside-the-canon-eos-1d-c/)
Hello-
I've been itching to update my firmware for 5D3 to 1.2.3 from current 1.1.3 -- as long as everyone else on 1.2.3 running ML nightlies with barely any issues.
Chime in your thoughts...
I don't mind staying on 1.1.3 if it is in fact less buggy than the new ones otherwise I'll just go for it.
Thanks!
Hello
Why the last 1.2.3 build is 07 august, its old no ?
Best regards
Just above: Reply #877
Answered in #878
Will we ever see that full res silent pictures feature in the 5D3.123 build? I'm very interested in this feature as I have some time lapses coming up I need to shoot.
get yourself a camera that has this feature or wait....
Will we ever see that full res silent pictures feature in the 5D3.123 build? I'm very interested in this feature as I have some time lapses coming up I need to shoot.
Quote from: vovkinson on October 22, 2014, 01:43:46 PM
get yourself a camera that has this feature or wait....
Will we ever see that full res silent pictures feature in the 5D3.123 build? I'm very interested in this feature as I have some time lapses coming up I need to shoot.
Thank you so much for all of your help!
Yesterday, I updated from 1.1.3 to 1.2.3 on my 5D3 with ML. The installation process was very simple, it has come a long way from a few years ago. I did not have any issues. I was able to record 1080p with a solid green icon for 1 min before I ended the test and after a 1GB card warm up on my KB 64GB 1000x. I did not come across bugs in my non-scientific tests. However, I did not use any HDMI tools.
Can u post the download link for the ML 5dmarkIII 1.2.3.
Refer to the first post of this article for the download and install instructions. You can download it by clicking on "It's Out!" on the first post.
Successfully installed ML 1.2.3 after updating firmware from 1.1.3 to 1.2.3 -- been itching to do this for some time. Love the new installation/uninstallation process. Features are pretty much the same if not better. 8)
Now I am curious (dumb enough to ask) how to implement Full_Res Silent Photos into my Modules... do I just copy the coding from the bitbucket site and merge them with the current Modules?
Thanks again everyone for your support!
http://www.magiclantern.fm/forum/index.php?topic=12608.msg129663#msg129663
Thanks @Audionut -- that's exactly what I wanted to see. You ROCK!
I'll test it out tonight after work...
I am not sure if this is the best place to post this.
I have 2 5D MK III's with the same latest firmware. I began using Magic Lantern on them. I noticed one of my 2 cameras wake's up and powers on way slower then the other. I have tried swapping memory cards, batteries. I even reset the problematic camera. I formatted the cards removing Magic Lantern but the camera still boots up and wakes up noticeably slower then the other one.
A google search brought me to this
http://www.dpreview.com/forums/thread/3016685 but its for the 5D MK II and a rather old thread.
Anybody ever seen this, know if its related to Magic Lantern having been used and how I might fix the problem?
To make ML run you need 3 things:
- Cam with bootflag set
- Bootable card
- Card with ML files on it
During startup a cam with bootflag set will look for a bootable cam. This will cause a slight delay during startup. Same for leaving powersave mode.
Formatting the card will *not* reset cam's bootflag!
You have to reset/remove cam's bootflag by running installation again. Look for instructions during installation. Just wait 30 seconds and bootflag will be gone after.
I am about to take the plunge. One question before I do - I currently have Canon Firmware 1.2.3 on my main CF card. I am considering putting the ML software on a separate SD card and using that card for nothing else. If I do, and both cards are in the camera at the same time could there be a firmware conflict?
My theory is that I will have the SD card in the camera whenever I want to use ML but if I want to revert to the Canon firmware I will just take that card out and re-start the camera. I am hoping it will then revert to the Canon firmware. Is that right?
Is the above a good strategy?
Thank you.
Quote from: insch on October 25, 2014, 11:32:10 PMI currently have Canon Firmware 1.2.3 on my main CF card.
You may have the file for the firmware update process on the card. But this is just a file and it is not doing anything on its own.
You can (and should) delete it after updating Canon's firmware.
Magic Lantern doesn't replace Canon's firmware. It runs a a task upon the OS of the cam. Just like any programm running at startup on your computer. And it is indeed loaded from the card at startup.
The rest: Top of Page -> User Guide -> FAQ
Thanks Walter. I understand that the Canon firmware file isn't doing anything off the card. The reason I have left it on there is just as a backup in case I ever need to re-install the firmware on the camera. You say that I should take the file off this card - is there any harm leaving it on there? Is the reason you advise taking it off that there might be a conflict with the ML firmware?
Best
F.A.Q
QuoteThanks Walter. I understand that the Canon firmware file isn't doing anything off the card. The reason I have left it on there is just as a backup in case I ever need to re-install the firmware on the camera. You say that I should take the file off this card - is there any harm leaving it on there? Is the reason you advise taking it off that there might be a conflict with the ML firmware?
Thanks Walter - are you saying that this has been dealt with in FAQ (if so, where is that?) or that it should be added to FAQ?
Best
Loving the features on 1.2.3 w ML -- I remember reading somewhere in the forums earlier that the 3x crop mode during RAW/MLV does NOT work. I understand that this works just fine on 1.1.3 -- would you guys suggest I downgrade in order to use 3x crop mode or is there a way to get it fixed on 1.2.3?
My gut feeling is that it isn't implemented into the 1.2.3 build yet...
Correct me if I'm wrong!
@DeafEyeJedi
i have used 3xcrop and it seems to work fine in the build from august 07..
@devs:
is there a possibility to get the improved read file mlv viewer, which can playback the mlvs faster? some time ago there were some threads about such improvements..
thx. swinxx
I believe the build I am using is the one that's from sept 27th? I'll check when I my hands on the 5D3...
i had the build from sept on my camera, but full res was not really working for me.. i got many errors, so i turned back to august, which seems stable, although no full res pic, and no fast mlv viewer on board..
hope that the build for 1.2.3 will soon be updated to be on par with all the other cams.
thx.
Copy that @swinxx -- however if i understand it correctly that indeed it is fine to stay on 1.2.3 as opposed to downgrading back to 1.1.3?
Strange enough though that full_res silent pic works pretty well on sept 27th build... I'll see if I can test out the 3x crop mode again. Because I could swear I shot it in 3x mode and then when watching it on MLRV 1.3.4 -- it just shows as if i never used the 3x mode.
Will confirm this again later tonight when I get home from work. Thanks all!
I missed the September 27 th build...it isn't in Downloads right? Still using 7th August build and it works great. Sometimes my cam freezes and I have to turn it off...for example when I record longer clips with 30 or 60fps...but everything else seems to work.
I really hope for the 7D2 to be more capable of 60fps...or is it only the card what limits me on the 5D3?
Thanks for the insight. My own magicball is in repair ...
Just got ML for the 5D Mark III and I'm really digging it. My previous cam was a 550D with ML and I noticed the Shutter Lock feature isn't on the 5D Version. Maybe I'm blind or that feature just isn't in this version?
http://builds.magiclantern.fm/#/features
Than you for that Audionut! I couldn't find this link before. Gracias
hi all,
i haven't installed ML on mark III yet...i have a question before doing so. right now, i'm primarily interested in having it on camera for audio level feature, but don't necessarily want to shoot RAW.
can i still shoot in factory 1080.24 format, while using audio levels from ML?
thanks.
goro
Top of page -> User Guide -> FAQ
colleagues, how to manage the 12 Gb barier for RAW writing?
Canon 5D MIII, FW 1.2.3, ML 07.08.2014 Lexar 64GB 1066x - formated in the camera
record stops at 12Gb (sometime at 4 or 8GB) with the question "Is it real exFAT card?"
thank you
Quote from: AleXis on October 30, 2014, 07:55:28 PM
colleagues, how to manage the 12 Gb barier for RAW writing?
Canon 5D MIII, FW 1.2.3, ML 07.08.2014 Lexar 64GB 1066x - formated in the camera
record stops at 12Gb with the question "Is it real exFAT card?"
thank you
Have you formatted the card as exFAT?
how can I do it in the camera?
I tried format card only in computer as exFAT - it doesn't help.
RAW ml video - has this problem
RAW video - works ok
Hi all, Apparently this is common knowledge so sorry for the noob question but I'm having some trouble benching my cf card in "playback mode" on my 5dm3 I have disabled live view in all my menus and still under mode in the benchmark utility it says movie
what am I doing wrong? or more to the point can someone please post a step by step including which setting should be set or not set to achieve this in camera and in ML? I have searched and searched and at best all I can find is directions to disable direct draw make sure your in playback mode etc with no clear direction on how to be in playback mode.
Thanks
Quote from: AleXis on October 30, 2014, 08:38:59 PM
how can I do it in the camera?
I tried format card only in computer as exFAT - it doesn't help.
RAW ml video - has this problem
RAW video - works ok
I'm guessing that this
isn't a 5D3 problem, ie camera specific, but has more to do with mlv, so have a look at the appropriate part of the forum, read the FAQ, use search to see if anybody has run into this and if you can't find your answer, THEN ask in the relevant place. Doing so will help to keep the mods in good humour. :)
http://www.magiclantern.fm/forum/index.php?board=49.0 (http://www.magiclantern.fm/forum/index.php?board=49.0)
Quote from: DAP on October 30, 2014, 10:20:40 PM
make sure your in playback mode etc with no clear direction on how to be in playback mode.
Make sure the movie mode switch is in playback mode. Which is the one next to the viewfinder, with the start/stop button in the middle.
Thanks Audionut, So if I'm reading you correctly make sure the mode switch is in stills mode? (white camera icon) I've tried that and in the bench utility it shows as mode:photo ? not mode:playback is this a new naming convention with the new build ? I'm on canon firmware 1.2.3 with ML Aug 7 build I guess whats throwing me is that I am trying to have Mode: Playback show in the benchmark utility and I can only produce Mode:movie or Mode:Photo
Thanks for your time ;)
Playback is that mode where you review your pictures or videos.
I guess it's time to lock this thread for another month :)
Hi folks, this is my first post on these boards =)
I've only recently discovered Magic Lantern, and I'm still educating myself on all the things it can do. I have yet to actually put it on a camera, but I'll be trying it out on my 700D over the weekend. I have access to a 5D3 that I use when working with a particular crew, and with the 7D2 sporting 1080p60, I started wondering...
Because of the bandwidth of a CF, the 5D3 can shoot raw 1080p30, but from my understanding it can't handle any frame rate much higher than 30 when shooting raw. But how about compressed footage? Is it possible that the 5D3 could handle compressed h264 1080p60 at nearly the same bitrate as raw 1080p30? Or is the Digic 5+ a bottleneck here?
Sorry if this has already been discussed in this thread, I did a fair bit of browsing to see if this was brought up but didn't find anything.
DigitalVeil,
I'm not an expert but your posting here does not have anything to do with ML.
Sell your 5DIII and buy another 7DII - problem solved! Woohoo!
QuoteDigitalVeil,
I'm not an expert but your posting here does not have anything to do with ML.
Sell your 5DIII and buy another 7DII - problem solved! Woohoo!
Yes, I actually was asking about ML. I guess I should re-phrase and simplify:
The 5DIII's CF slot allows write speeds fast enough to support recording raw 1080p30. ML lets you take advantage of this by giving you the option to record raw 1080p30 instead of compressed h264, as long as your card is fast enough. ML also gives you full control over frame rate and bit rate. Because of this, wouldn't ML enable the 5DIII to theoretically be able to shoot 1080p60 in the default h264 compression with a bit rate around 90MB/s?
Also, the 5DIII isn't mine to sell. It's collectively owned by a small crew/studio that I work with sometimes, and I'm trying to convince them to try ML on the camera. 1080p60 is something we'd love to have, even if compressed. I'll eventually get my own 7DII after putting aside enough cash for one, but I'd still rather shoot 60fps on a full frame than cropped frame!
http://www.magiclantern.fm/forum/index.php?topic=5472.0;topicseen
Quotehttp://www.magiclantern.fm/forum/index.php?topic=5472.0;topicseen
Thanks, but I'm not interested in raw 720p60. I'm interested in compressed 1080p60, and whether or not that's even a possibility on the 5D3.
h264.ini - how it really works?
http://www.magiclantern.fm/forum/index.php?topic=8949.0;all (http://www.magiclantern.fm/forum/index.php?topic=8949.0;all)
Quote from: DigitalVeil on November 01, 2014, 07:15:11 AM
I'm interested in compressed 1080p60, and whether or not that's even a possibility on the 5D3.
No, it's not (http://www.magiclantern.fm/forum/index.php?topic=11570.msg113776#msg113776)
If 1080p/60 is important then perhaps look into the upcoming c100 mark II...
Quote from: dmilligan on November 01, 2014, 03:25:43 PM
No, it's not (http://www.magiclantern.fm/forum/index.php?topic=11570.msg113776#msg113776)
So it is a hardware limitation then. Thank you, that's all I was interested in.
I just randomly decided today to downgrade back to 1.1.3 (which was easy to do) then I ran into realization that there isn't alpha build 1.1.3 enlisted under Downloads anymore... is there a reason for this to be taken off?
I still have the Alpha build saved on my macbook BUT it just keeps saying Data not found please install all ML files. I know I did this repeatedly but still no luck. However, I also read on the Downloads page that it also mentioned to upgrade to 1.2.3 first before installing 1.1.3 (not sure what this means) but I am currently upgrading back to 1.2.3 after successfully downgrading to 1.1.3 (but no luck with ML installation)...
anyone else out there experiencing similar situation as I am? :-\
IMO -- its fine using ML on 1.2.3 but after resaerching the forums apparently its a bit faster shooting RAW on 1.1.3 as oppose to 1.2.3 thus the reason why I decided to downgrade to 1.1.3 just to do this test BUT again it may not be worth the hassle since 1.2.3 works just as flawlessly other than RAW_TWK.MO module that would NOT work on 1.2.3 (assuming it only works on 1.1.3) correct me if I'm wrong on this.
Perhaps it may be best to stick with 1.2.3 ML until further updates...
THANKS!
SJ
https://builds.magiclantern.fm/jenkins/
Hey all,
Long time reader, first time poster here. I updated my firmware to 1.2.3 today and used the most recent nightly build as my source of Magic Lantern. I noticed a problem in LiveView that when half pressed, the Canon exposure overlay on the bottom keeps popping up on top of the Magic Lantern overlay. Anything I can do to remedy this?
Normal: http://i.imgur.com/vcWrFPY.jpg?1
Half-Pressed: http://i.imgur.com/POZQGvV.jpg?1
I've been looking through the forums and my camera all evening not sure what to change so any help would be very much appreciated!
Quote from: Walter Schulz on November 02, 2014, 08:03:14 PM
https://builds.magiclantern.fm/jenkins/
Thanks @Walter Schulz -- however whenever I try to install ML 1.1.3 after successfully downgrading from 1.2.3 to 1.1.3 it still says ML DAT FONTS retry despite the fact that I compiled the ML folder from the Jenkins site directly unless I'm missing something?
Only reason why I want to do this is because I want to do another benchmark testing with the new KB 128gb 1066x (which disappointed me with the results on 1.2.3 but hoping that it would be slightly faster on 1.1.3 with its reading speed. I was getting avg of 92.4 write/121.2 read which is not even close to their advertising of 160/150MB's
Anyone else experiencing similar effects with KB 128gb 1066x?
UPDATE***
I ran Macboot Command (its been awhile since Ive been on 1.2.3 up until then) through terminal and set the DSLR bootable which did the trick now that ML is working on 1.1.3 (My fault on that guys!)
Quote from: Walter Schulz on November 08, 2014, 08:21:36 AM
Compiled? You're sure not to confuse "download and extract" with "compiling the sources to get binaries"? And if you really compiled: Why?
Not sure why but I just figured since I remember I had to use Macboot Command to make the 5D3 bootable on 1.1.3 so I did that and now ML is running fine and currently benchmarking the KB 128gb 1066x to see if the Write/Read speeds are similar or not...
I didn't mean to be absurd by labeling it averages -- guess I assumed that it would be polite to post the 'average' rather than posting screenshots of my BM's but since you mentioned that no one else has ever used this terminology so my apologies for that confusion.
In fact it is showing slightly higher numbers on both the Write/Read speeds as I type...
I am already aware of the fact that the CF card slot had a bottleneck of about 120/mb write speed which was why I was kind of perplexed by the fact that the KB 128gb 1066x I have in my hand may be a defective one... will run some more tests before I make a final decision.
I believe there is another thread where I can post screenshots since it would be a violation of the policy if I were to post them on this particular thread.
Thanks for your feedback @Walter Schulz
Can you post speed differences between 1.1.3 and 1.2.3 in this thread (http://www.magiclantern.fm/forum/index.php?topic=13446.0).
Thanks Jedi.
Hello to everyone,
I just wanted to know why there is not any update since early august for the 5D3 1.2.3 Nightly ? Is there any problem ? It used to be updated a lot more often... I'm wonder. Thanks for the enlight !
There's been no merged updates to the code so no new build is created... the reason why are posted in the thread...
Any help for the issue that I posted earlier? Or is it completely normal?
As will be realized per channel adjustable audio channels in the 5D MARKIII, as was done in 5D MARKII ?
Quote from: Stedda on November 08, 2014, 02:21:43 PM
There's been no merged updates to the code so no new build is created... the reason why are posted in the thread...
unhelpful without link please post :)
What is love? Baby don't hurt me, don't hurt me... no more.
8)
Any news? 4K 15 stops...?
Yep, Red Epic
QuoteAny news? 4K 15 stops...?
I'm experiencing two issues with latest nightly build which I'm not finding any solid info about, so I thought I would try here.
1. I ran the 5 minute benchmark on the CF card I am using and saw write speeds never getting above ~45 MB/s. The card is a 800x Lexar Pro (http://www.amazon.com/gp/product/B0093HGEKG/ref=od_aui_detailpages00?ie=UTF8&psc=1) which claims to support up to 120 MB/s. I'm assuming either I have not tweaked something which I should have or there is some issue within the build which is affecting my write speeds.
2. The second issue is a bit more complex. I have 3x 32Gb CF cards which I have previously used with this camera just fine. I installed ML on the above Lexar CF card without incident and everything apart from the poor write speed is functioning normally. I wanted to make sure ML was on all of my cards. I powered the camera off, removed the ML-CF card, inserted the new one so I could format it before adding the ML files and following the boot-flag procedure. The camera wouldn't power on. Nothing. Removed and reinserted the battery, card, in different orders, nothing. Removing the battery and reinserting the ML-CF card before reinserting the battery got the camera to power on just fine. I'm stumped as I have not experienced this on other ML installs I have done across multiple cards for other cameras. Ideas? Could it be a bad card which makes both of these issues connected somehow?
Quote from: vagabondvisions on November 18, 2014, 04:19:14 PM
1. I ran the 5 minute benchmark on the CF card I am using and saw write speeds never getting above ~45 MB/s. The card is a 800x Lexar Pro (http://www.amazon.com/gp/product/B0093HGEKG/ref=od_aui_detailpages00?ie=UTF8&psc=1) which claims to support up to 120 MB/s. I'm assuming either I have not tweaked something which I should have or there is some issue within the build which is affecting my write speeds.
No, you've done everything you should have done and there is nothing you can do about. Benchmarks for Lexar 800x:
http://www.tomshardware.de/cf-karten-compact-flash-compactflash-typ1-typ2,testberichte-241502-3.html
http://www.tomshardware.com/charts/compactflash-charts/-2-Sequential-Write-MB-s,3489.html
hey all,
I just tried loading the latest nightly, and it works perfectly on one of my cards, but on two others it does the CF test when I turn it on and freezes when it hits (40) two cards, every time. I tried an older build from July and the same thing. Is this indicative of a fault in my cards? Is there anything else I can do to try to troubleshoot? thanks.
http://flashfakecentral.wordpress.com/testing-flash-memory-chips/h2testw-english/
This test is destructive and all data stored on the flash drive will be lost.
Hey Guys, Ladies,
I have an issue with the Audio Menu on the ML, It's sows me only 2 sub-menu items, Speaker Volume and Beep Test Tones..Do I need to do something special to have all the Audio Menu showing?
My second problem: On my SmallHD monitor no Magic Zoom Available in HDMI 1080i, does somebody knows if it's a fix for this or i will need to buy the SDI version of the monitor, will it work on that?
I am on 5DMark3 with 1.2.3 and the August Nightly Build Installed.
A hug from Transylvania for all the ML lovers/creators.
Quote from: Ciprian_Sauca on November 21, 2014, 09:28:20 PM
I have an issue with the Audio Menu on the ML, It's sows me only 2 sub-menu items, Speaker Volume and Beep Test Tones..Do I need to do something special to have all the Audio Menu showing?
@Ciprian_Sauca
Did it work for you before? Have you searched the forum?
If you did, good! ;D
-Did you start/load the audio/sound module from the MagicLantern menu?
-Did you restart the camera after doing this?
-?
Because this has been asked a gazzillion times, and often been a very easy fix... :'(
Hey Daniel,
I have loaded the MLV Sound Module, shows on the Audio Task Bar along the other 2 that I was talking earlier, but no sign of the full audio menu. I have tried before posting with the manual, within the forum, maybe I don't address the issue properly.
Thanks for the reply and sorry for the mess-up but if you can guide me to the page that will resolve my problem I will be more then happy.
Good Night Magic Lantern People....
Take a look here:
https://builds.magiclantern.fm/#/features
You will notice some audio options missing for 5D3. Don't know if a dev is working on this.
Hey Walter, Kudos for you...This fixed my issue...They are not ready yet on the Mark III.
I have discover something else while playing thru the menus. I have an SmallHD monitor and while is connected to my MarkIII the Magic Zoom will not work on it, it is written on the bottom that will not work via HDMI 1080i. Do you have any clue about this and if is there any fix for it or it in the same stage as the audio module? Maybe if I buy an SmallHD SDI? Will this go thru?
A warm hug from the Carpatian Mountains....
Sorry, not familiar with HDMI issues on 5D3. Hope someone else will jump in.
No problem, Thank You for the assistance and see you around here.
Cheers!
I was thinking about getting a 5D MKiii for Black Friday or Xmas.
Of course I want to install ML on the 5D MKiii, but I want to know what are the current problems with ML for the 5D MKiii.
I shot a 600D (T3i) using ML and it worked flawlessly for me. So I was wondering whether ML will work flawlessly on the 5D MKiii as well.
I really like the timelapse features (e.g., intervalometer, AETTR, deflicker, dual ISO, etc.) that ML offers for the 600D.
Does ML for the 5D MKiii also have all of these features?
Also, I've been reading about this "boot flag" problem. What is this problem and has it been fixed?
I also been reading about ML 1.1.3 vs ML 1.2.3. Which one is more stable?
Lastly, has anyone ever experienced any serious problems with the 5D MKiii after installing ML? I doubt it, but it never hurts to ask since all the Devs are very meticulous and competent coders.
Any help to these questions is appreciated. Thanks.
I have installed ML on both of my 5D3s since June. No problem. The bootflag issue is resolved now (it can be removed by installing again and waiting for 30 seconds...)
I have been using 1.2.3 for a few months now when I was using 1.1.3 previously. People brought up that 1.2.3 is slower than 1.1.3. This may have been in the early stages, which would be expected but. The latest build, Aug 2014 I believe, doesn't seem to be slower for me. I use 64 KB cards.
Ive asked this question in the 1.1.3 thread but im guessing development on that firmware has stopped.
Just wondering if it is possible to have Magic Zoom triggered by the half shutter press as with the MKII, instead of just the Magnify button on the left side as it is now? It would make the world of difference using that function for event work. Cheers!
Hey guys
Any plans to do a ML port on the 5d Mark IV when it comes out next year? If not, I don't think I'll even bother waiting to buy one. I can't see the point if there's no ML Raw.
Thanks for the amazing work you did on the Mark III!!
You guys rock.
We don't make plans based on rumors.
Is it technically possible to have Magic Zoom triggered by the half-shutter press as it was on the MKII?
Quote from: woody084 on December 05, 2014, 04:42:52 AM
Is it technically possible to have Magic Zoom triggered by the half-shutter press as it was on the MKII?
This feature works well on the 7D and would definitely be a +1 if it were to be implemented in the nightly for 5D3 one of these days...
Quote from: DeafEyeJedi on December 05, 2014, 06:16:21 PM
This feature works well on the 7D and would definitely be a +1 if it were to be implemented in the nightly for 5D3 one of these days...
+2
Recommend starting its own topic. I'll bump it.
Good call @dubzeebass!
Hello there,
is the 2 second delay you never get rid of again still and issue? Or can I get my camera back as it was after using ML?
Also if watching a raw video stream is not working very well on the camera about about a connected android smartphone? Would this work to check the recording?
1. It's possible to fully remove ML now
2. You need a computer with a decent GPU to be able to playback raw video in realtime (demosaicing is a rather computationally intensive task)
BTW: this thread is not the place to be posting questions about raw video (as has been stated many times previously)
That sounds good. Could I put ML on a small SD card and just remove it to turn it off?
No option to check the recorded raw video on set is not so great though.
Top of page -> User Guide -> FAQ
You can watch but review in realtime is not possible.
Does the 4GB limits also affect raw video recording?
How is raw video on the battery, I would imagine it could save some compared to normal encoded video because the CPU doesn't have to compress it..but then its more data. Will it empty my batteries faster?
QuoteBTW: this thread is not the place to be posting questions about raw video (as has been stated many times previously)
Hello everyone, and sorry in advance if my questions make you pull your hair out in frustration. It is not my intention. I promise.
I have been following the project for e few years and the the tools you release and the results that can be made with them are pretty amazing. I am a film photographer who most of the time shoot on my own 5D3 1.2.3., but the RAW-video results that ML produce are unbelievable. It looks close to something coming out of a way higher end camera. SO, enough babbling. Since the camera is expensive, I just want to shoot you a few questions. Feel free to ignore them if you do not have time to answer.
Is there still an issue with pink pixels?
Have anyone – as far as you heard of – destroyed or broken their camera, 5D3 in particular, by using ML?
Since the boot flag issue has been resolved; does that mean that the camera can now be restored to actual factory settings with no trace of hack? I have found it hard to find an answer to this.
How reliable do you (users in general) find ML to be?
I would ideally like to use it when doing video production work, but am also well aware that this is something without any guarantees. I would however very much appreciate any info or experiences that you want to share regarding the reliability and stability. There is always a risk when using with software like this, but it is alot easier to make the jump if it seems to be working well for others already.
Thank you, and keep up the great work!
Hi,
does anybody know why there are no more nightlies for the 5dII 1.2.3 since August? Other branches get updated, so it does not appear to be a complete stall of the development...
kontrakatze
The last build for any ML supported cam run 8th of October.
https://builds.magiclantern.fm/jenkins/
I don't know which branches you are referring to.
Simple: Because a1ex has stopped the development.
I guess development on the SLR's are done now due to this new fancy schmancy 4k camera they're working on now :(
@Walter Schulz: No, the 5dMark III 1.2.3 latest build is from August 7th.
But I anyway, I used the word branches in a misunderstanding way. What I meant was, that the builds for different cams are not the same date and that there are no new ones.
Yes, it seems the whole project is stalled for whatever reason. But I can't believe that this here is a one man show and if a1ex has other things to do, it breaks. Or am I wrong?
Relax guys... This is the same pattern they go through on a yearly basis -- everything is gonna be alright and I'm a happy swinger between 1.1.3 & 1.2.3 nightlies with no fear of destroying the 5D3!
QuoteBut I can't believe that this here is a one man show and if a1ex has other things to do, it breaks. Or am I wrong?
Wrong, it's open to everyone of us to contribute and since it's free a1ex can stop anytime and doesn't owe anyone a reason why...
The last build is perfect for me..no drops no pinks everything is fine working with monitors & external recorders..all is stable for me. I think the development is capped for this camera...you wont get 4k or coffee out of it coz its hardware restricted...what more do you want?
Hey dubzeebass, where should the seperate topic for the 'Magic Zoom on half shutter for MKIII' be created? Or have you done it?
Super keen for this function or to know if its technically possible.
I reckon under Feature Requests :)
Hi guys,
I just installed the latest Nightly Build for my 5d3 after updating the camera firmware but I cant load the modules like I used to do on 113 canon firmware. Can you guys help me with this?
Most of the video features are not here on this build as it used to be before when I was using the 113 firmware.
please send me any hint.
Best
Does the "Voice Tag" feature work on a Canon 5dmiii?
I don't see it anywhere.
I downloaded ML just a few days ago.
At time of writing this function is not implemented in nightly builds.
Development is dormant right now. Expect some news next year.
See http://www.magiclantern.fm/forum/index.php?topic=9848.msg133878#msg133878
How is the latest version doing with eye-fi cards in the SD slot?
hey .. i have installed ML the latest build for the 5dmkIII running 1.2.3 .. there was no problem so far ... i did some raw recording etc .. but i came to format card remove the bootflag , so i did it .. now i have trouble that the camera wont boot from time to time after removing the ML firmware ... i can get it running by removing battery , cards etc switching on/off.. and than i get a startup .. i updated over the 1.2.3 .. with no sucsess... it seems that after a time the camera seems to go in a freeze .... i can turn off/on with sucsess when i do it in short time .. if i leave the camera with battery cards off for let say an hour it wont boot into orginal state .. any idea ?? thx !!
Sorry, unable to sort out what you did and tried to do.
Remove battery, remove card. Insert battery. Don't insert card. Startup cam.
Results?
without cards camera starts .... as soon i put a card in it doesnt start ... have two cards 1 CF lexar1066x 64gb + eyefi pro/x2 16gb.... after i put the cads in i get no led conformatiom/ the camera hangs until i remove the battery ... all this is after i removed bootflag + format card in camera ...
You haven't removed the cam's bootflag. And the cards are still bootable.
Copy you ML downloads (extracted) to card: FIR + Autoexec.bin + ML directory
and run install again to remove cams bootflag and delete cards bootoption.
Remaining cards may be formatted using a cardreader but that's up to you.
After the cam's bootflag is removed they will use bootable and non bootable card the very same way.
ok i did run firmware update from the ML card , i waited for x sec to remove the bootflag, i got the info bootable 0 in the right upper corner .. its done ?
I can't know until you try ...
Query;
I am currently running ML newest nightly build on an SD card only in my 5d3. I wanted to enable dual ISO and it tells me to enable RAW photo quality from the Canon menu, which I have. However since I'm running SD card only in the second slot, I'm assuming dual iso is checking for the CF card and not finding it, causing this message. Just wondered if anyone could confirm or perhaps let me know if I am doing something wrong :)
Have used dual iso on my t3i a lot in the past and been very surprised and impressed with what it could do.
I guess you have to enable RAW and either choose "Auto Switch card" or "Rec to Multiple" options.
So as to be able to write RAW even on SD card when CF is missing.
TEST:
I have selected RAW (only), "Rec to Multiple" option and removed my CF card. I have enabled DUAL ISO and it works.
Quick question: Is the latest version the Nightly.2014Sep26 (22:33:23) or there is an even newer build?
Thanks
That fixed it, thanks!
Now I gotta read the help files and learn the menu a bit, its laid out differently with a different option set than the version I had on my T3i - I had 2 ISO's to work with before and now it has a "Recovery ISO" field instead.
Any indication of how long its likely to be before AGC toggle is added to this build for 5D3. Its the main reason i want to use ML with 5D3. Just want to find out if its long term problem or a short term fix.
Turn it off in the regular camera settings. Set audio to manual.
i have two 64 CF cards .. want to use both in exchange so one can go to backup while i record on the other one ... how to manage in context of ML ?? what happen with the setting file etc ....
Quote from: remure on December 31, 2014, 06:13:37 PM
i have two 64 CF cards .. want to use both in exchange so one can go to backup while i record on the other one ... how to manage in context of ML ?? what happen with the setting file etc ....
By far the best option IMHO is to buy a cheap SD card and use it exclusively for ML.
You may copy ML\Settings from one card to another. ML has no sync mechanism for users of multiple cards.
On cams with multiple slots it is indeed easier to use one card to start ML from and several data storage cards.
i have a eyefi 2x pro 16gb card .. can it be used for ML ??? i have read somwhere here not to use the eyfi cards ..
Any slow and outdated SD-card with 4 MByte or up (yes, it's an M and no G!) will do.
I tried using an eyefi card while I had ML installed on a CF card and it froze up my camera, with the magiclantern-Nightly.2014Aug07.5D3123 build. I wouldn't recommend using eyefi along with ML.
Yup. Eyefi cards do not work for ML :(
Hey guys, Sorry if I'm missing something but when I go to the ML nightly download page http://builds.magiclantern.fm/#/ and select 5D3.123, the latest build was on 2014-08-06. When I select 5D3.113, the latest build was on 2015-01-02. Is there a reason the ML build for firmware 113 is being developed more often than the 123 firmware? I thought all development has been migrated over to the the 1.2.3 firmware. Thanks for your help!
Oh, Nightly Builds are running in again!
If you look into release history you will see there was a break for about 3 months for all camera versions.
ML for 5D3 1.2.3 is something *not* following the "standard" pace.
Quote from: walter_schulz on January 03, 2015, 09:47:58 PM
Oh, Nightly Builds are running in again!
If you look into release history you will see there was a break for about 3 months for all camera versions.
ML for 5D3 1.2.3 is something *not* following the "standard" pace.
I knew about the development hiatus, but I guess you're right that it's not following the "standard" schedule. I looked a few pages back and saw the post from a1ex about him wanting to focus more on the stills functions rather than video. Hopefully someone else will take over the development.
Hi tron, where did you find the Sep 26 build? The latest I could find is an Aug 08 for 5DIII 1.2.3. Please let me know! Best.
Give me some time to search again since I have it for some time. I believe though it was in the silent pictures thread.
I will come back.
In the mean time plz read this
http://www.magiclantern.fm/forum/index.php?topic=12523.msg129721#msg129721
EDIT: I cannot find them! I have found this instead:
http://www.magiclantern.fm/forum/index.php?topic=12608.msg129663#msg129663
// Builds removed. These builds should have been used for development related feedback, not just being able to try new (experimental/dangerous) features. Audionut.
« Last Edit: November 17, 2014, 05:41:59 AM by Audionut »
Hello
I know this has been asked before - however after extensive searching I just cant seem to find an answer - or I don't understand any answer that I've read.
The 1.2.3 Nightly build hasn't updated since August 2014 - however the 1.1.3 Build is updated as of January this year.
Are there any plans to create a more recent 1.2.3 build?
I've tried reverting to 1.1.3 and then using a 1.1.3. nightly but they don't contain any .fir so I can't use them.
Is my answer just to wait for a new 1.2.3 nightly?
Many thanks and all help appreciated.
Quote from: gabesosa on January 06, 2015, 07:09:04 PMAre there any plans to create a more recent 1.2.3 build?
Yes
Quote from: gabesosa on January 06, 2015, 07:09:04 PMI've tried reverting to 1.1.3 and then using a 1.1.3. nightly but they don't contain any .fir so I can't use them.
Install Canon's firmware 1.2.3. Use Nightly Build for 1.2.3 to set cam's bootflag and make the card bootable. Downgrade to Canon's firmware 1.1.3. Delete ML folder and Autoexec.bin from card and copy extracted "ML for 1.1.3" to card.
Done. You are running ML for 1.1.3
Quote from: gabesosa on January 06, 2015, 07:09:04 PMIs my answer just to wait for a new 1.2.3 nightly?
42!
Quote from: Walter Schulz on January 06, 2015, 07:23:44 PM
Install Canon's firmware 1.2.3. Use Nightly Build for 1.2.3 to set cam's bootflag and make the card bootable. Downgrade to Canon's firmware 1.1.3. Delete ML folder and Autoexec.bin from card and copy extracted "ML for 1.1.3" to card.
Done. You are running ML for 1.1.3
Really clear! Thank you!
Quote from: Walter Schulz on January 06, 2015, 07:23:44 PM
Install Canon's firmware 1.2.3. Use Nightly Build for 1.2.3 to set cam's bootflag and make the card bootable. Downgrade to Canon's firmware 1.1.3. Delete ML folder and Autoexec.bin from card and copy extracted "ML for 1.1.3" to card.
Done. You are running ML for 1.1.3
Gah!
I'm sorry but this bit just doesn't seem to work. When I Downgrade to Canon's firmware 1.1.3 it resets the bootflag on the camera. It boots nothing from the 1.1.3 card.....
Canon's firmware update/downgrade won't affect cam's bootflag. Period.
Describe in detail what you have done. I suppose you formatted the card during the operation and made the card non bootable.
You may make the card bootable again by using EOScard.
Or do it right this time. Don't format the card after running 1.2.3 installation!
If you have a second card: Format it using a cardreader and use this one for Canon's firmware only.
Thank you for your patience.
Steps:
Have 1.2.3 ML running fine.
ML Card has autoexec.bin, ML folder and ML5D3123.FIR on it. Nothing else.
Remove ML Card
Have second card with Canon 1.1.3 on it because I don't want to mess with the bootable-ness of my ML Card.
Insert Card 2 with Canon 1.1.3 on it.
Update (backdate) firmware to 1.1.3.
Remove Card 2.
On my mac I delete contents of ML Card and replace with 1.1.3 nightly contents.
ML Card has autoexec.bin and ML folder only.
Camera boots. Doesn't load anything from card. Just plain vanilla 1.1.3.
Admit to be buffled right now ...
It *should* work but ...
Some thoughts:
What is of note is that when I have to revert back to 1.2.3 and use the ML5D3123.FIR to set the bootflag it does give me a message saying that the bootflag is already set. So you are absolutely right about Canon firmware changes not affecting the bootflag (I didn't doubt you anyway).
So the bootflag IS set on the camera.
The camera boots straight into vanilla Canon.
If there is a bootable card but no autoexec.bin then the camera would hang on startup.....
I removed the contents of my ML card. It doesnt hang.
Which means the the ML card is (for some reason) no longer a bootable card.
This MUST be it. (if my thinking is correct?)
I'll work on it.
Yes, but you are right and wrong.
The part wrong is: Running the installation process your card will be made bootable.
Q: "Removing" ML parts as in deleting AUTOEXEC.BIN and ML directory or as in formatting the card using a cardreader. Second one will render the card non bootable.
Whats confusing is that I haven't formatted the card at any time. Just deleted contents using mac finder window.
I'm going to download EOSCard/Macboot and check the card/change the card.
Just to confirm:
I have Canon 1.1.3.
I have bootflag set (it MUST be).
Then ALL I need is a working bootable card with ML 1.1.3 nightly on it....
Yes, absolutely correct!
Cam with bootflag set will look for a bootable card.
If bootable card is found AUTOEXEC.BIN will be loaded (or cam will get stuck if file is absent).
ML directory holds config data and some other stuff.
SOLVED!
So I used EOSCard on a PC to prepare the card. Put latest nightly on it and BOOM. Works exactly as it should. I'm running ML 1.1.3 dated 03 Jan.
Hooray.
I worked out what was causing the problem:
Deleting the contents of the ML card (not formatting, just deleting) using finder on mac was making the card non-bootable for ML 1.1.3.
I have NO IDEA why that would happen.
It was made even more confusing due to that process working fine for 1.2.3 whenever I reverted back to it...
Again - no idea why it would remain bootable for 1.2.3 but not for 1.1.3 using the same process (deleting and replacing contents.... NOT formatting).
Walter thank you so much for your continued help.
And I thought I was living on a funny farm sponsored by MS. Not the only sponsor, I suppose.
Glad to read you sorted it out!
And is it any worth of downgrading FW for using last ML?
Quote from: silenthunter on January 11, 2015, 10:03:10 AM
And is it any worth of downgrading FW for using last ML?
What firmware version do you have currently? If you have 1.2.3 then you probably want to stay with the 1.2.3 version of MagicLantern. If you have a version newer than 1.2.3 I will send you a message to find out a bit more.
I have recently bought mk3 and have 1.2.3 version, but I see that there is no update od ML since august 2014 and for 1.1.3 is updated a few day ago, that's why I'm asking, is it worth to downgrade to 1.1.3 and install latest ML or no?
Going from 1.2.3 to 1.1.3, the significant loss in the Canon firmware will be the ability to auto focus at f/8.
Yes, but we all know what's new in Canon firmware (new vs old), but I was wondering is it worth to downgrade FW just to get using an updated version of ML, are there that much important and useful things?
To make it simple: should I (and everybody else) stick to 1.2.3 and ML from 2014y (and wait for newone) or it is better to downgrade FW and use a fresh new ML?
I'd suggest sticking with 1.2.3. The two ML versions are almost the same, it's just that the 1.2.3 branch of the code hasn't been updated with the latest changes yet. There have been very few changes since August so you're not really going to be missing out on anything of note. The only benefits you'll get downgrading to 1.1.3 are slightly faster RAW video recording (makes 1080p continuous a bit easier to reach) and a few small things like fast zebras and full screen magic zoom (because their new register locations haven't been found on 1.2.3).
As previously said earlier -- I'm a happy swinger between 1.1.3 & 1.2.3 for the most part I prefer 1.1.3 only because of the slightly faster recording times for RAW/MLV which can also push the MB/s a little higher therefore chances of dropped frames can be slimmer.
Depending on the settings, obviously!
And with 113 you have silent pictures, right?
correct. I miss having the FRSP for 1.2.3 though... I somehow misplaced it somewhere in my external drives and chances are that I may have accidentally deleted 'em.
So I only have the Sept 27th fixed version FRSP for 1.1.3 which works well (however, I'm still struggling to compile with the code that @a1ex made) in order to extend the shutter speed to 1/20-1/30th as oppose to the limited 1/15th.
I know, I'm an iDiot!
;D
4k recording on Eos 5d MArk III:
1 I cannot setup higher recording resolutions in the Magic lantern more than something like 1,5K. There are I saw up to 4 k resolutions but the software does not permit me to choose. Why? ( I have the latest available Magic lantern version of August 2014)
2. Ok I got the Atomos Shogun. How could I record RAW from Magic Lantern over HDMI directly in to the Shogun? Also combined with the hopefully positive answer of question 1 how could I record 4K thanks to Magic Lantern directly into the Shogun?
1. There is no 4k recording on 5d3. THe highest really usable res is 2.5k in 2,35:1 aspect ratio (in crop mode). It is because of limitation in memory cars write speed. In full frame max is 1920x1280.
2. Camera doesnt output raw through hdmi, only uncompressed 4:2:2 8bit 1920x1080. Please do a little bit of reading the forum, especially pinned topics.
Thank you Kgv5
`1. in magic lantern there is max resolution 3584. It doesnt work Why?
2. Ye I know that the camera doesnt output raw, my adjusted question shall be would Magic lantern do this? or the HDMI output is something that only the camera can control?
1.Because in 24fps it will exceed maximum data rate which camera is able to write. You can use this 3.5k but only in low fps/some extreme aspect ratio like 3:1 or so.
2. Hdmi output is something which ML is unable to control due to the hardware limitations.
Quote from: FIRST POST
Any messages about RAW/MLV from this thread will be deleted without notice.
It's time to start enforcing this, since we've asked nicely quite a few times now, and people don't seem to care.
You're actually right about that @Audionut -- my apologies for the lack of knowledge (well I did know but just need to be aware of my actions a bit more before responding to other's depending on the thread) -- *Tapatalk sometimes gets me carried off while driving but that's no excuse!
Today found updated firmware 1.3.3 (http://usa.canon.com/cusa/professional/products/professional_cameras/digital_slr_cameras/eos_5d_mark_iii) on EOS 5D Mark III.
I hope that it still be possible to run ML on it and please check http://www.magiclantern.fm/forum/index.php?topic=14350.0
to vote for SATA-CF adapter for this camera.
We've been there with 1.3.3 before (camera came installed with this fw version) and the first person who had this problem was able to downgrade using EOS Utility.
No, for now 1.3.3 is incompatible with ML. Must be ported first.
Regarding firmware 1.3.3, see here: http://www.magiclantern.fm/forum/index.php?topic=14399.msg138925#msg138925 (http://www.magiclantern.fm/forum/index.php?topic=14399.msg138925#msg138925)
I updated all the stubs a couple of weeks back (assuming the dump I had matches the official release). Still need to calculate the signature and check/update the font addresses but apart from that I don't think there's too much else required to get the 1.3.3 port up and running.
Just Downgraded from 1.3.3 to 1.2.3 in EOS Utility with no trouble,Happy again
Using the drop down menu from the ML download paged linked from the original post in this thread, and choosing 5D3 123, I get the download page but when I click download its a 404 file not found. Is there an alternate download link ?
No problem here. Direct download link (same as in "Download" button): https://builds.magiclantern.fm/jenkins/job/5D3.123/37/artifact/platform/5D3.123/magiclantern-Nightly.2014Aug07.5D3123.zip
Thanks.. your linked worked but it would not work from the download page for me for some odd reason. Even right clicking on the download button and saving target as. Anyway I got it now. Thanks.
Every installation guide I find, people always seem to forget the part about THE SD CARD HAS TO BE MADE BOOTABLE
:)
"THE SD CARD HAS TO BE MADE BOOTABLE"
Really? Since when? The ML fir file did it once...
The fir file enables the bootflag in camera. Making a card bootable is another thing.
The installations instructions are 3 steps long, and they still cause problems!
Quote from: skrull on February 07, 2015, 07:56:14 AMThe fir file enables the bootflag in camera. Making a card bootable is another thing.
Depends. In fact the installation procedure sets the cam's bootflag *and* makes the card bootable.
To make a card bootable you may run the installation procedure once again or use EOScard/Macboot. Second option may be preferred by users running 550D, 600D or 5D3.113 because they don't have a 3-step easy install routine.
Quote from: Audionut on February 07, 2015, 07:58:34 AM
The installations instructions are 3 steps long, and they still cause problems!
I wrote a rant about people who cannot reproduce these steps sucessfully, but I decided not to post. Altough I still think that they shouldn't be using ML.
I posted this questions in another ML forum - reposting it here to hopefully get an answer sooner:
Just received my 5D Mark III back from Canon for an HDMI port repair and discovered that they updated my firmware to 1.3.3! For the past year I have been shooting RAW with the ML hack exclusively with this camera. Am I screwed? Is there any way to install an older firmware once the newer one has been installed? Does not appear that a ML build for 1.3.3 is happening any time soon. Please help. Thanks
@clapalm -- Just read this post..
Quote from: Aryan on January 30, 2015, 04:15:34 PM
Just Downgraded from 1.3.3 to 1.2.3 in EOS Utility with no trouble,Happy again
It is possible to do it with EOS Utility.
Good Luck!
I am not sure how someone was able to revert back to 1.2.3 from 1.3.3 using the EOS Utility. I am on a Mac running 10.10.1 and an older Mac running 9.2.1 and using various versions of EOS Utility I get the same results - I can see the firmware version within the settings tab, but it is greyed out and I can't access it. I would appreciate anyone who has a answer on how to dial the firmware back to reply.
Thanks
http://addedoptimization.com/5d-mark-iii-firmware-update-using-canon-eos-utility/
Quote from: clapalm on February 09, 2015, 08:46:19 PM
Just received my 5D Mark III back from Canon for an HDMI port repair and discovered that they updated my firmware to 1.3.3! For the past year I have been shooting RAW with the ML hack exclusively with this camera. Am I screwed? Is there any way to install an older firmware once the newer one has been installed? Does not appear that a ML build for 1.3.3 is happening any time soon. Please help. Thanks
I'm not sure about Mac but I've downgraded from 1.3.3 to 1.2.3 a whole bunch of times already on Windows. It worked fine every time, I just plugged in the USB cable with the camera on and in photo mode and the menu item becomes available.
If you do have trouble downgrading and want to live on the edge a little, you can try building the 1.3.3 port (https://bitbucket.org/hudson/magic-lantern/pull-request/605/support-for-5d3-firmware-133/diff (https://bitbucket.org/hudson/magic-lantern/pull-request/605/support-for-5d3-firmware-133/diff)). Don't forget to report back any bugs you might find.
Wow - thanks so much for posting the article on how to over ride the greyed out firmware upgrade function of the EOS Utility. Followed those instructions, dialed back the firmware to 1.2.3, reloaded ML to my SD card and I now am back in business. A thousand thanks.
Hi, sorry for asking but I need to be sure.
I have held off flashing ML 1.2.3 because the first page always said the bootflag is not reversible.
Today I read the firstpage and it says no longer says the bootflag is not reversible.
Can ML be removed completely now?
Yes. I have. And I've reinstalled it.
can i download firmware 1.1.3 from someplace?
i have 1.2.3 and want to run the 1.1.3 build.
i don't see an option to downgrade that far on the eos utility site.
http://pel.hu/eoscard
When recording standard h264 om mk3 123 and using my zacuto evf I get this black bar hiding a bit of the top of the frame. It disappears when recording raw and mlv. Anyone else experiencing this problem? I read that someone created a transperant cropmark bmp and got rid of it. Any other solutions?
So I used EOSCard on a PC to prepare the card. Put latest nightly on it and BOOM. Works exactly as it should. I'm running ML 1.1.3 dated 03 Jan.
Hooray.
I worked out what was causing the problem:
Deleting the contents of the ML card (not formatting, just deleting) using finder on mac was making the card non-bootable for ML 1.1.3.
I have NO IDEA why that would happen.
It was made even more confusing due to that process working fine for 1.2.3 whenever I reverted back to it...
Again - no idea why it would remain bootable for 1.2.3 but not for 1.1.3 using the same process (deleting and replacing contents.... NOT formatting).
Walter thank you so much for your continued help.
i did all of the above and it still didn't install. I also didn't reformat the card and still no install of 1.1.3 build. i did notice on the eoscard it still said 1.2.3 stable version with a drop menu next to it but no 1.1.3 option. i duno if that makes a difference or not but no matter how many times i tried, I wasn't able to install ML to my 5d3. can anyone offer any suggestions?
I'm taking the plunge.
Is 113 or 123 the one that most people prefer? I do use my 5D3 for commercial shots, which one of those do you find the most reliable? Does one of them have any certain advantages over the other? I record audio externally.
113. hands down. 123 for HDMI out (if needed) -- enough said!
i'm still trying to figure out how to put on 1.1.3 i followed all the instructions from an earlier thread to make the card bootable but still can't get the card to work. can anyone help?
Format card in cardreader, make card bootable (EOScard/Macboot) and copy extracted nightly contents (1.1.3) to card.
OS X: We had - at least - two incidents with OS X making a card non-bootable (on it's own). So check after copying and run Macboot again.
So I just got a 5D MIII and my firmware says it's 1.2.3, but when I try to add in the ML software it tells me "Memory card requires firmware update" with and without the ML SD card inside, but it won't let me update. I tried reinstalling 1.2.3, even though that's what I originally had, but nothing is working with the ML card. Any suggestions?
Sorry, unable to follow your description.
ML version used is?
You copied extracted nightly build contents to card?
QuoteWhen recording standard h264 om mk3 123 and using my zacuto evf I get this black bar hiding a bit of the top of the frame. It disappears when recording raw and mlv. Anyone else experiencing this problem? I read that someone created a transperant cropmark bmp and got rid of it. Any other solutions?
I have the same problem if I use an external monitor (hdmi out - no mirroring). Did you get rid of the problem?
On the other hand when I activate mirroring I noticed that the image is slidly cropped on the monitor in comparison to the lcd screen or the final recording. I remember that someone had the same problem but I can't find that post right now. Does anybody have the same issues?
I'm on 1.2.3.
[Long time lurker - first time poster.]
First, much respect and thanks to the talented ML team. I tried searching for a few keywords but couldn't find any hits.
With the 1.2.3 ML build, I am finding that camera operations work fine (no shock), but I have a very concerning issue with lens AF and IS noises. When using a 17-40L, a 24-105L and a 70-200L IS II, the AF operation is much louder and has a "sliding" noise, that sounds like pulse-width modulation (PWM) being applied to the AF drive. Also, the IS sounds are much louder when it engages/disengages. This is when operating through the viewfinder, with default settings in ML.
I have done several rollback tests to Stock firmware and ML, and it is 100% reproducible, and it is alarming that the motor drive sounds of the lenses is so different. Trust me, this is not me hearing phantom noises, I even had my family members confirm it and they remarked that it was "much noisier" using ML.
I have since gone back to stock firmware, but any ideas on what would cause this, and if there is any log data I can capture to provide the team? I can't imagine it's just me seeing this, unless most ML users are strict manual focusers.
Can you record a video showing the problem? (stock firmware vs ML).
If the difference is clear, do the following tests:
1) start the camera by holding the SET button pressed at startup (this loads ML, but it's inactive)
2) if noise is fine after doing 1), start ML normally and turn off everything you can find in ML menu
3) if noise is fine after doing 2), start enabling things until you find the culprit.
Hi there, i`m new to this ML , I just wanted to install the 5D Mark III 1.1.3 build but i can`t. What`s wrong with this ? Am i missing some files ?
In the builds download section i see this message :
Quote
You cannot use this package for first install.
To install ML, please upgrade to firmware 1.2.3.
The 1.1.3 firmware might be a little faster in RAW recording (not confirmed).
Now i`m confused , i`m suppose to upgrade firmaware or what ?
Files that i have from the latest build magiclantern-Nightly.2015Feb20.5D3113 are only the autoexec.bin and a ML folder. And i`m using the initiall 1.1.3 firmware that came with my camera.
Quote from: Ohim on February 27, 2015, 01:47:45 PM
Hi there, i`m new to this ML , I just wanted to install the 5D Mark III 1.1.3 build but i can`t. What`s wrong with this ? Am i missing some files ?
In the builds download section i see this message :
Now i`m confused , i`m suppose to upgrade firmaware or what ?
Really????????????????
I`m confused .. the build is there 1.1.3 and even has nightly from 2015 as opposed to 1.2.3 that has from 2014... but i can`t install it..
You may read the bit about installation. The fun part is: You can't install 1.1.3 without installing 1.2.3
EDIT: A bit of advice. Upgrade Canon firmware to 1.2.3, install ML for firmware 1.2.3 and play around a bit. Will do just fine. Or do you have some real fast cards? 1000x or up needed for top performance (=a little bit higher resolution for continuous recording) with 1.1.3.
EDITEDIT: And there is not that much difference between 1.1.3 and 1.2.3 code.
1.2.3 doesn't take part in standard build procedure. 1.1.3 does. If there are changes in code for another cam a new 1.1.3 build will be generated. And if you look into version history you will have a hard time finding changes for 5D3.
1.2.3 build is triggered only if there is a cause.
Thanks for the replies, i`ve figured it out in the end. Kinda weird that you can`t install 1.1.3 directly.
Hi
I'm trying to build 5D3 1.2.3 but I'm receiving this error:
../../src/debug.c: In function 'HijackFormatDialogBox':
../../src/debug.c:3546:68: error: expected ')' before 'FORMAT_BTN_NAME'
dialog_set_property_str(dialog, 4, "Format card, keep ML " FORMAT_BTN_NAME);
^
../../src/debug.c:3548:70: error: expected ')' before 'FORMAT_BTN_NAME'
dialog_set_property_str(dialog, 4, "Format card, remove ML " FORMAT_BTN_NAME);
^
../../src/debug.c: In function 'handle_keep_ml_after_format_toggle':
../../src/debug.c:3563:22: warning: comparison between pointer and integer [enabled by default]
if (event->param == FORMAT_BTN && MENU_MODE && MEM(DIALOG_MnCardFormatBegin))
^
../../src/debug.c:3563:22: warning: comparison with string literal results in unspecified behavior [-Waddress]
../../src/debug.c: In function 'CopyMLFilesBack_AfterFormat':
../../src/debug.c:3781:36: error: 'FORMAT_STR_LOC' undeclared (first use in this function)
HijackCurrentDialogBox(FORMAT_STR_LOC, msg);
^
../../src/debug.c:3781:36: note: each undeclared identifier is reported only once for each function it appears in
make: *** [debug.o] Error 1
My last successful build was at the beginning of January. I didn't change anything with my compilers. I've found one conflict with src/bootflags.c in 5d3-123 branch but it's not related to this error.. Is there something new in ML?.. I'm using gcc-arm-none-eabi-4_8-2013q4 . Should I upgrade something ?
FORMAT_BTN_NAME and FORMAT_STR_LOC are not defined (in consts.h). These were added when "restore after format" was fixed. I assume you can just use the same values as in 5D3.113.
Are you compiling a later build for 1.2.3? If so can you share it?
@marekk:
That would be delicate of you to do so!
:)
dmiligan - thanks for the hint
#define FORMAT_BTN "[Q]"
#define STR_LOC 13
should be replaced with
#define FORMAT_BTN_NAME "[Q]"
#define FORMAT_BTN BGMT_Q
#define FORMAT_STR_LOC 13
Fresh ML for 5D3.123 with changes from fullres-silent-pics branch
http://goo.gl/nZvk5J
Modules:
deflick.mo dual_iso.mo file_man.mo mlv_rec.mo pic_view.mo silent.mo
autoexpo.mo dot_tune.mo ettr.mo mlv_play.mo mlv_snd.mo raw_rec.mo
INSTALL AT YOUR OWN RISK
Thanks @marekk!
Has anyone tried this yet?
Just need to update my 5D3 first from 113 to 123 before attempting to try this fresh build.
Definitely tempting though...
[emoji12]
Seems to work but some text font issues seem to be their for some reason
It's only autoexec.bin with modules.. It's not a full ML package.
Full package is available here:
https://drive.google.com/file/d/0B-7nnVbwzGVkNkRwMTNCMXBXQlU/view?usp=sharing
INSTALL AT YOUR OWN RISK
Hi,
I don't understand something, that I guess you can answer in a second, so here goes:
Why are there a 1.1.3 and 1.2.3 version for the Canon EOS 5dmk3 Camera? They both require the 123 firmware version so I guess that is not the reason.
I would suspect that the 123 version is the newer one, but it seems that it is not being updates since the last nightly build is from August last year. I just installed the 123 version. Should I instead go with the 113 version?
Another think. Why is there no stable version anywhere?
Hope someone will take the time to answer my question.
/Brian
Quote from: Mnemonic on March 01, 2015, 06:47:52 PMAnother think. Why is there no stable version anywhere?
"Stable" is more than 2 years old and devs decided to switch to "Rolling Release" development model (Look it up in Wikipedia.) some time ago. 1.1.3 is supposed to deliver faster write rates (= higher resolutions). 1.2.3 supports all the fun stuff Canon decided to put in. f/8 with AF and some other things.
Walter/Alex
A related question if I may. As photographer I'm not interested in video, but, as I have a long lens I'm interested in focus at F/8, hence I changed to the 1.2.3 as soon as it came out.
However, as has been noted, only the 1.1.3 ML is getting refreshed.
Could someone please clarify if 1.2.3 will be brought up to date, or should I consider dropping back to 1.1.3?
Much appreciate any feedback.
It will be updated at some point, most likely after merging fullres silent pics, maybe faster if @marekk submits a pull request. For now, I've downgraded to 1.1.3.
Alex
Thanks for the very quick reply :-)
I'll keep my eyes open for the 1.2.3 version, but might downgrade 'for fun'.
Cheers
Garry
Hey everyone, quick question about external monitors.
I'm using 1.1.3 since ages and I've been following the 1.2.3 development since it's been released without feeling the need to upgrade.
I'm about to shoot a personal project using a DJI Ronin using RAW and the question of external monitoring comes. I know one of the benefits of 1.2.3 is clean HDMI out, but from your experiences, is it worth the upgrade ? I mean, is the 480p out from 1.1.3 really dirty and unstable ? And if I upgrade to 1.2.3, are there known issues with external monitoring, or will it work seamlessly ? Is there a thread dedicated to that (I've read the forum for hours).
Last observation about upgrading/downgrading firmware back and forth between 1.1.3 and 1.2.3. I've read that some of you guys do it on a regular basis ("happy swingers"), but I recall a1ex saying we might avoid doing that because each time it moves/removes/add code into the camera core and it can have consequences in the long run. Is that really critical or just a general guideline to avoid up/downgrading 5 times a day ?
Thank you so much for the work you guys have done and keep doing. I really hope to see a1ex getting back on it, and I hope I'll be able to contribute again to this fabulous project.
I didn't know there was a problem with switching from 1.1.3 to 1.2.3. I'm using fresh builds for 1.2.3 from the beginning without any issues. I'm using mlv_rec mostly..
I do got a sound question. Im using ML for my 550d and now got a 5dmk3. Is there any way that i can switch the Sound like in the 550d ? To left internal, and right External ? Since i also want to use it for vox pops its every essential for me
Cheers
Brechstange
@marekk
There are no problems with 1.2.3, I've been using ML on my 1.2.3 5DIII since the it was first made available.
However, at the moment, the 1.2.3 build version is not being automatically updated in the nightlies, ie it has to be handraulically done.
But, as a photographer, I'm content with the version I have and can wait until the 1.2.3 build is incorporate.
pardon my ignorance - i had a look at 1.1.3 alpha 3 release notes and 1.2.3 bleeding edge -
which one is better? so is 1.1.3 now superior to 1.2.3?
Others will add to my humble view I'm sure.
Because ML is now on a rolling update basis, all you need to look for is the latest release for your camera.
Many cameras are automatically updated.
The 1.2.3 on the 5DIII is not.
That is my understanding.
Regarding firmware 1.23 and clean HDMI out...
I shot a short last summer with 1.13 and lower res HDMI. It was challenging at times to focus. I shot most of it with a Canon 135mm and a Sigma 35mm Art. With the 1.13, at least, it was easier to recognize focus with the 135 because the fall off and bokah are very noticeable. With the 35 lens the lens softer so gradually, it could be hard to figure out when I had tack sharp focus.
After that short I upgraded to 1.23 and the focusing is way way easier. Still not always easy, but way better. The firmware has been very stable, too.
Us 5D filmmakers are relying on a beautiful challenging camera. A DP friend of mine, who shoots big TV shows, never uses a 5D cause the sensor makes focus a pain. When they throw a DSLR into the mix with the Alexa, they'd opt for a 7D. And nowadays he opts for the GH4.
Thank you for the feedback lostfeliz !
I think I will update to 1.2.3 to benefit from the clean HDMI out. As you explained, not easy to pull focus on a 480p stream.
Have you noticed any problem while using 1.2.3 ? I generally don't record for a long time (2min at most) so it shouldn't be a problem. But I'm more worried about interviews that tend to last for more than 15/20 minutes, where 1.1.3 seems more efficient.
Thanks !
I shoot with 64GB cards. When I shoot long take scripted, we can shoot an 11 minute long take in RAW at 1080/24. But if I'm shooting interviews, I shoot h264.
Not sure if there are issues shooting 20-22 minute 1080/24 clips with 128GB cards. There aren't any I know of.
Maybe if you shoot 720p you could shoot up to 30 minute RAW clips.
I'm not having any technical issues that are serious or cumbersome. Just the regular dreams for even more features, options and refinements from the incredible Magic Lantern team!
Downgrading to 1.1.3
If someone are interested, check the explanation of the advantages and what not work in this version (HDMI out, Dual Monitor and F8 focus).
http://www.magiclantern.fm/forum/index.php?topic=14704.0
Good to see A1ex is busy again with the new build uploaded yesterday. I'll load it today and give it a try!
Yesterday was my birthday! Literally :-)
So Far so good.
I have used both 113 and 123 and what I can say is this.. ::)
1.2.3 to me was MUCH more stable(I know pretty Ironic), much!
I'm sure there are a lot that will disagree
but the experience for me with the 1.2.3 was good. If I set a shoot on specific settings and shot it I would not get any weird shit happening and If I set the same settings the next day I would get the same results. It was consistent and reliable.
With the 1.1.3 the experience is hard to put in to words. Its like one leg in and one leg out, at times I will get really good results and at times I will not so what I'm trying to say is that 1.1.3 is not really consistent with its results. And for that reason I can't do any professional work because I'm terrified of either getting frame skipping or pink frames etc..
Since I've downgraded to 1.1.3 I have gotten more crashes(frozen and had to take battery out) than I can count but I never got a single crash on the 1.2.3, EVER.
At this point i'm contemplating between which one I should stick with and haven't made a decision yet but the constant crashes in 1.1.3 is making me lean more towards on 1.2.3
BTW whats going on with the 1.3.3?
How to reproduce those crashes?
Are you sure 1.2.3 doesn't crash if you repeat the same action that crashes on 1.1.3? Can you double-check and do a proper bug report?
With the newly released version I'm getting tearing and random colourful frames. KB64/1000x cards & 5d3. Anyone else? What do you need to troubleshoot?
1. Find a way to reproduce.
Most likely this will not be something fully deterministic. Look for things like "if I record 10 videos, each of them 10 seconds long, with settings XYZ, about 2 or 3 of them will have pink frames".
2. Check if the problem still happens on the previous version (last summer). If yes, stop here.
3. Downgrade to 1.1.3 and see if the problem persists. If no, stop here.
4. Do a binary search to find the exact nightly build where the issue appeared.
Once that build is identified, we will know where to look.
Sorry i am in a hurry, but I get those random colorful frames within a take with firmware 113 and the latest ml version. for me 123 seems also much more stable although 113 seems to record a little faster.
Hi,
I have on some tests shots, sometimes a bad frame, like a flash on the upper part of a frame using mlvrec from the last build from march 2015.
Raw Video / bad frames with using mlvrec from 2015Mar16.5D3123 build on 5d3
I did too test shots with rawrec recording: no problems
So i downgraded to 1.1.3, loaded the last build for 1.1.3 and make new mlv test shots and had same results, sometimes a bad frame.
Then i upgraded to 1.2.3 and used the last 2014 7 August version of the 1.2.3 ML firmware, and did mlv test shots again. No problem
I did a last test. i loaded again the 2015Mar16.5D3123 build but replace the mlvrec module by the one of the 2014 7 August version. Test shots. No problems, no bad frames.
It seems then related to the mlvrec module on the last build, for 1.2.3 and 1.1.3.
Any ideas?
I did too test shots with rawrec recording: no problems
To AL3X : Yes I have ran some tests, same tests to be exact on both firmwares and my results are the same.
I did tests on different res to different aspect ratio, to different fps.
I even did some tests with unloading module except for the raw rec just so I can get the best results when it comes to fps and res size.
As TWINXX said, 1.1.3 might be a lil faster but 1.2.3 is much more stable.
Hello everyone. I installed Magic Lantern on my 5DMK3 (1.2.3). Let me know if this is normal that in my Audio menu I have only two options? "speaker volume" and "beep, test tones."
Where are the other options?
Where can I find recent screenshots of magic lantern for 5DMK3?
And I want to know how to put the white balance to "auto"? Thank you !
Sorry for my English !
Yes, Audio menu looks like that. Use Canon's menu to tune audio settings. You will get more menu options in ML for MLV sound recording after MLV_SND.mo is loaded.
And setting WB to auto is done in Canon's menu, too.
Thank you very much, indeed I solved my problems. There are still fewer options for 5DMK3 than other models, right? Or you can find it in the options menus Canon?
There are cams which more options and there are cams with less.
See http://builds.magiclantern.fm/#/features
Thank you, is that we can hope for improvements for the 5D3 or arrested development?
Sorry, what are you talking about?
Things handled properly by Canon will not be ported to ML.
Hello :)
@ swinxx, bayard1965 and itsDPmikey
Can you tell me since when exactly the new bad frames problem started, were the march versions before okay (there were a lot)? I just need to start my final degree work next week and would like to stick with 1.1.3 because of 50p. But I want to minimize the risk of getting bad frames :) Which nightly to take?
And just of curiosity. Do you think, that it is okay to get the newest ML nightly, but exchange the older, more stable mlv_rec module? Or should I better leave it alone, because the module is connected to the Firmware and could produce version dependent errors.
Thanks a lot!
EDIT: Oh, one more question. I noticed, that in 1280 mode the pixel height for cinemascope is now 1920x490 rather than 1920x508 before. Is this supposed to be? If yes, what is the reason, because many people could get continuous 1920x508 50p. I thought maybe this way you can get continuous 1920x490 60p but no chance. Nightly 1.1.3 March 25 - sandisk extreme pro
Did everyone already installed new version 2015-03-16 for 1.2.3 fw? :D
I didn't notice any changes so far.
Quote from: johannsebastianbach on March 25, 2015, 08:49:48 PM
Hello :)
@ swinxx, bayard1965 and itsDPmikey
Can you tell me since when exactly the new bad frames problem started, were the march versions before okay (there were a lot)? I just need to start my final degree work next week and would like to stick with 1.1.3 because of 50p. But I want to minimize the risk of getting bad frames :) Which nightly to take?
And just of curiosity. Do you think, that it is okay to get the newest ML nightly, but exchange the older, more stable mlv_rec module? Or should I better leave it alone, because the module is connected to the Firmware and could produce version dependent errors.
Thanks a lot!
EDIT: Oh, one more question. I noticed, that in 1280 mode the pixel height for cinemascope is now 1920x490 rather than 1920x508 before. Is this supposed to be? If yes, what is the reason, because many people could get continuous 1920x508 50p. I thought maybe this way you can get continuous 1920x490 60p but no chance. Nightly 1.1.3 March 25 - sandisk extreme pro
I have the latest 5d3 build with the MLV_REC and SND from the August build and it works perfectly.
Quote from: dubzeebass on March 26, 2015, 12:32:34 AM
I have the latest 5d3 build with the MLV_REC and SND from the August build and it works perfectly.
Does the newest build include the full red silent pictures mode? Anxious to see how that is!
No, that's not in the nightlies yet.
I shoot with a SmallHD AC7 monitor on my 5D3 and I've seen that there is a significant crop happening on the AC7 while running ML. I've tried settings on the AC7 but i don't see anything in ML that seems to fix this. Anyone have any ideas?
to johannsebastianbach,
I have used the ML 1.2.3 since first day I got my 5DMIII and it was very stable/reliable. It was just recently last month I think, that I decided to try the 1.1.3 since there were so many people claiming that 1.1.3 was better or faster. I experienced the crashes and choppy flickery pink frames as early as the first day of installing 1.1.3.
I just want to say that this is not a rant or anything like that. I highly respect the geniuses behind ML and I thank them for their hard work. The fact that they have worked so hard to give us the option to choose between what works best for us is really great.
In my opinion...
-IF you are using a LEXAR 1066X or something as equivalent, AND you know you aren't going to push anything higher than 30fps with normal 1080 or lower, to do professional work without much worry and get consistency then I would recommend 1.2.3
BUT!
If you are someone who wants to push the limits(over 30fps x 2K or 60fps x 1080) understanding its consequences and want to find out whats the best results they can get(might not be consistent) then I would recommend 1.1.3
ALSO keep in mind that some modules and features are firmware specific.
Do you have "DSLR Scale" activated on the AC7? It crops the incoming signal because Canon DSLRs used to output the image with a black frame around the image. FW 1.2.3 changed the output to Fullscreen so You don't need the feature on a 5DIII.
Yes i have "DSLR Scale" off however it looks as tho the AC7 still recognizes that the signal is from the 5D3. If you look at the image.. may be a little hard to see but you can see all of the door handle and you can also see the wall thermostat on the camera LCD but is not in the AC7. I have a photo of it but I'm not used to how the HTML insert photo thing works.
I don't have a cropping issue with my Ikan 7" monitor and 1.2.3 firmware. Without it, I'm hopeless trying to get sharp focus with a 5D.
So i solved my own issue.. I updated the firmware on my AC7 and that fixed the issue :) Thanks ML guys for all your smart brains come up with!
I've ran some tests with MLV for about 45 minutes, trying to push it beyond limits (30/60fps, 3.5K, magic zoom or focus peaking while recording), but could not get a single pink frame or crash.
Tried on both 1.2.3 and 1.1.3.
Therefore, without proper feedback from those experiencing the issue, there's nothing I can do. I'm looking at you, itsDPmikey, bayard1965, swinxx, dubzeebass, and others who may have reported it in other threads.
I repeat the instructions:
Quote from: a1ex
1. Find a way to reproduce.
Most likely this will not be something fully deterministic. Look for things like "if I record 10 videos, each of them 10 seconds long, with settings XYZ, about 2 or 3 of them will have pink frames".
2. Check if the problem still happens on the previous version (last summer). If yes, stop here.
3. Downgrade to 1.1.3 and see if the problem persists. If no, stop here.
4. Do a binary search to find the exact nightly build where the issue appeared.
Once that build is identified, we will know where to look.
@a1ex Just got my 5D Mark III & tested the latest nightly build running on 1.1.3 all day yesterday and I haven't encountered any pink frames seems to be very stable for both slomotion shots and regular 1080p. Also one observation I'm getting more than 25 sec recording shooting full 1920x1080 48fps Slomotion, and about 18 sec shooting 60fps MLV format with audio using a Lexar 1066x 64GB card. Was reading other post and others were just getting 5 sec max. Thank you for all the developments of the Hacks..
Quote from: goldenchild9to5 on March 28, 2015, 04:48:25 PM
@a1ex Just got my 5D Mark III & tested the latest nightly build running on 1.1.3 all day yesterday and I haven't encountered any pink frames seems to be very stable for both slomotion shots and regular 1080p. Also one observation I'm getting more than 25 sec recording shooting full 1920x1080 48fps Slomotion, and about 18 sec shooting 60fps MLV format with audio using a Lexar 1066x 64GB card. Was reading other post and others were just getting 5 sec max. Thank you for all the developments of the Hacks..
What settings are you changing for the 48fps and 60fps, just the regular "desired fps option"? Are you still setting the Canon menu to 720p60?
@jordanwalkert What's sup Jordan here are my settings..
Canon Menu: Image Quality: RAW (No Jpeg) not sure if it makes a difference but that's what's working for me.
Auto Lighting Optimizer: OFF
Long exp. Noise Reduction: OFF
High ISO Speed NR: OFF
Highlight Tone Priority: OFF
Multiple exposure: Disable
HDR Mode: Disable HDR
Video Mode: 720p 60fps ALL-I
Magic Lantern: Overlay: Global Draw: On, all modes (When Global Draw off you get more seconds like 25+ Seconds I was able to get @ full HD)
Spotmeter: On
Histogram: On
Waveform: On
Movie: Raw Video (MLV) 1920x649 aspect ratio 16:9 (In Resolution submenu make sure you have Card Warm-up On, mines is set to 128MB - Extra Hacks ON - Use SRM Job ON
Files > 4GIB (exFat) On and you can mess around with the rest)
So far those are all the settings I'm currently using, still tweaking it to see how much more I can get out of the camera. One more thing before you shoot any Raw videos make sure you format your CF card to ExFAT for longer recordings. If you have any other questions feel free to ask take care.
Quote from: goldenchild9to5 on March 28, 2015, 09:40:51 PM
@jordanwalkert What's sup Jordan here are my settings..
Canon Menu: Image Quality: RAW (No Jpeg) not sure if it makes a difference but that's what's working for me.
Auto Lighting Optimizer: OFF
Long exp. Noise Reduction: OFF
High ISO Speed NR: OFF
Highlight Tone Priority: OFF
Multiple exposure: Disable
HDR Mode: Disable HDR
Video Mode: 720p 60fps ALL-I
Magic Lantern: Overlay: Global Draw: On, all modes (When Global Draw off you get more seconds like 25+ Seconds I was able to get @ full HD)
Spotmeter: On
Histogram: On
Waveform: On
Movie: Raw Video (MLV) 1920x649 aspect ratio 16:9 (In Resolution submenu make sure you have Card Warm-up On, mines is set to 128MB - Extra Hacks ON - Use SRM Job ON
Files > 4GIB (exFat) On and you can mess around with the rest)
So far those are all the settings I'm currently using, still tweaking it to see how much more I can get out of the camera. One more thing before you shoot any Raw videos make sure you format your CF card to ExFAT for longer recordings. If you have any other questions feel free to ask take care.
Thanks so much for the info! I appreciate it. I guess what confused me is that you said you were getting slow motion at 1920x1080, but in your settings you have your resolution as 1920x649. Are you stretching it in post??
Yep Stretching in post..
Thank you a lot for the answers :)
I noticed, that in 1280 mode the pixel height for cinemascope is now 1920x490 rather than 1920x508 before. Is this supposed to be?
@johannsebastianbach Don't really use the cinemascope function so I'm not sure about it's previous aspect ratio, plus I just got my 5D Mark III. Been using other cameras with magic lantern 7D, 5D2 & 50D..
With cinemascope I mean only the aspect ration 2.35:1
So if you choose 1280 mode for slow motion and choose aspect ratio 2.35,
Before it was 1920x504 (or508?), now it is 1920x490.
@johannsebastianbach I see.. I think it's because it's on 2:35 aspect ration try putting it on 16:9 and see what happens. I'll try it myself later today and report back.
1.1.3 march 25th nightly, but it was on march 16th too.
before I had the 1.2.3 august nightly and it was 504 (or508??)pixels high. Worked continuously too.
thanks :)
In 16:9 is shows me 1920x648 pixels resoluion.
@johannsebastianbach I just checked and it's 1920x490 in 2.35:1 aspect ratio. I think before it wasn't the right pixel ratio, all I know is Magic Lantern Team Knows Best :D.. it's only a few pixels less you won't really see any difference in the image.
AL3X what exactly are your settings to achieve 3k?
Try shooting RAW/MLV in crop-mode and see if you can gain higher resolutions... [emoji6]
Jm2c.
To clear up the confusion about 720p mode and vertical pixels in 2.35:1 ratio: The computation of the squeeze factor wasn't always correct and a patch I made submitted recently fixes that.
The correct vertical squeeze factor is 5/3 = ~1.666x before it was reported as 1.61x
So in current magic lantern one should get a resolution of 1920/(2.35*1.66) = 490.
Quick question:
I have a Canon 5D Mark III and want to try ML. As of now I only have a single SD card but will get a CF card in the nearest future. Can I save my pictures and video files to the same card as Magic Lantern is installed on or do I need to memory cards?
Thanks, Jakob
Short answer:
Yes.
Caveat:
Dont format the card once you have ML loaded on it if you use only one card. If you want to format the card I would uninstall ML, copy ML files to a temp folder on the computer, format the card, Reload ML files from the temp folder and re-install ML. However, the development gurus may give you a shorter process.
Best practice (mine):
Get a SD card for ML. They are dirt cheap. You can get by with a 1 GB card. I have a 4GB card.
Why that complicated? Default format option will keep ML on the card.
Thanks Walter. Could you elaborate for me?
Top of page -> User Guide -> FAQ -> Usage -> 4th question
@Greenduck, above is your answer. I told you the development gurus would give you a better solution.
:)
Thanks guys for the quick answers. I will definitely get another card for for ML and one for images/video.
Looking forward to try out ML. It seems it really opens up for the cameras video capabilities.
So I've installed ML on my SD card and as far as I know I'm recording to my Sandisk Extreme 64GB 120MB/s CF card. I have loaded the following modules: mlv_play, mlv_record and raw_rec. But when I record I get an error message about skipped frames after 8-15 second.
"Early stop (11) Didn't make it to estimated record time"
How do I solve this?
Your card only writes 60mb/s
http://www.bhphotovideo.com/c/product/1003356-REG/sandisk_sdcfxs_064g_a46_64gb_extreme_compact_flash.html
And loading MLV_REC.mo and RAW_REC.mo at the same time doesn't make much sense.
Will really hurt only after activating both record modes in movie tab.
I upgraded the firmware on my 5D MK III to 1.3.3 and now the ML on my SD flashes but will not allow the camera to boot and has to be reset by removing the card and battery. Also the Eye Fi card will not allow the camera to boot as well. Is there a fix for this? Please send any tutorial that will let me regain my camera funtions.
Format cards using your cardreader.
Magic Lantern builds are always for a specific version of the Canon firmware. In the case of the 5D3, there are nightly builds for 1.1.3 and 1.2.3 firmware only. There is experimental code that provides 1.3.3 support but it is not well tested and you would have to build it yourself.
If you still want to use Magic Lantern, I'd suggest you downgrade back to 1.2.3 or 1.1.3. If you no longer want to use Magic Lantern, you should disable the bootflag on your camera by flashing the ML installer .fir firmware and waiting a minute for the bootflag to be disabled (as per the on-screen instructions). You might need to downgrade to 1.2.3 for this to work.
Quote from: esphoto57 on April 08, 2015, 05:52:48 PM
I upgraded the firmware on my 5D MK III to 1.3.3 and now the ML on my SD flashes but will not allow the camera to boot and has to be reset by removing the card and battery. Also the Eye Fi card will not allow the camera to boot as well. Is there a fix for this? Please send any tutorial that will let me regain my camera funtions.
AL3X: I've ran some tests with MLV for about 45 minutes, trying to push it beyond limits (30/60fps, 3.5K, magic zoom or focus peaking while recording), but could not get a single pink frame or crash.
Tried on both 1.2.3 and 1.1.3.
Therefore, without proper feedback from those experiencing the issue, there's nothing I can do. I'm looking at you, itsDPmikey, bayard1965, swinxx, dubzeebass, and others who may have reported it in other threads.
Ok AL3X, I again did a few tests and had same issues.
23.976FPS
1920X1080 mlv
EVERYTHING normal default settings.
"Ok AL3X, I again did a few tests and had same issues.
"
I just watched the video. Boy those pink flashes are very reminiscent of digital dropout you used to get on digital video tape. Is it possible the write speed of the card is not fast enough? Have you low level reformatted the card so it is not fragmented? I'm curious if the card is fragmented, could it be trying to write to contiguous space and it causes dropout.
Quote from: unfilmde on April 11, 2015, 07:58:47 PM
"Ok AL3X, I again did a few tests and had same issues.
"
I just watched the video. Boy those pink flashes are very reminiscent of digital dropout you used to get on digital video tape. Is it possible the write speed of the card is not fast enough? Have you low level reformatted the card so it is not fragmented? I'm curious if the card is fragmented, could it be trying to write to contiguous space and it causes dropout.
Well I'm no expert and can't really be sure what the cause is but I don't think its the card because I have 3 of them and all 3 get the same results. I have 2x 32gb LEXAR 1066X UDMA7 65 and 1 128gb LEXAR 1066x
Also One more thing that makes me think its not the cards is that just last night I upgraded to 1.2.3 and used the latest 1.2.3 build and recorded bunch of diff FRAMERATES and resulutions up to 2.5k wide cinematic ratio and NOT 1 single drop of frame or pink frames or glitch effect(did not test on all cards, assuming would be same results)
Again this is my own personal experience and thoghts that 1.2.3 is more stable and reliable.
But I'd like to get more of your opinion on the defrag situation which I don't think I have ever done. I always format cards
IN THE CAMERA when I'm done offloading the files.
Instead of formatting as exFAT?
IMHO, I feel more confident when shooting in 113 versus 123* only because I like to be able to squeeze every ounce of speed as much as possible and I also don't really need the clean HDMI out nor the F8 autofocus fix....
*Unless I'm using it on paid gig when field monitors are required.
That's JM2C!
Quote from: DeafEyeJedi on April 12, 2015, 07:17:29 AM
Instead of formatting as exFAT?
IMHO, I feel more confident when shooting in 113 versus 123* only because I like to be able to squeeze every ounce of speed as much as possible and I also don't really need the clean HDMI out nor the F8 autofocus fix....
*Unless I'm using it on paid gig when field monitors are required.
That's JM2C!
Yeah I understand trust me I know its pretty ironic since everyone says
"1.1.3 is more stable", but what can I say this is my personal experience and I even provided some proof of it.
I'm having a frustrating problem with my 5D III ml 1.2.3. The intervalometer is not working constantly with CF Lexar 1066x 128g. Specially when used every 1, 2 or 3 seconds. ML is in a Sony SD class 10 16 gb.
¿Do anyone knows what is going on?
Im sorry if im not putting the post in the right place but I dont know how to do that. Any help is welcome too. ;)
Thanks.
Benchmark your CF-card first.
If results are ok (= not a faked card with inferior write rate) reset ML to defaults (backup ML\Settings).
Do not use Liveview. Disable "Image review". Just enable Intervalometer and start with 3 seconds interval. If running smooth you may try 2 and 1 seconds interval. Report results.
Just wanted to say, today i bought my brand spanking new 5D3 4 hours ago. It already has Magic Lantern on IT! :)
Thanks Walter, i run the card r/w benchmark test twice. The result in the first one was 98.64 average and the second one 100.25. I think is ok ¿am i right? the .ppm file apearded on my sd intead of my cf im not shure ir i did it ok but i think i did.
Then i made the CF+SD write speed test and results were: SD: 28.8 MB/s and CF:122.1 MB/s
(sd card is supposedly 94MB/s) ¿Does the issue could come from the sd instead of the CF?
I tried the intervalometer below 3 seconds and i'm still having the problem . I'm not using live view and image review is deactivated... ¿ any advices ?
Thanks a lot for your help.
Average tells nothing at all. Highest write rate for each card is interesting, however.
5D3's SD-card interface is limited to about 21 MByte/s write rate. You really got 28.8 written?
I run it again: SD 19.8 CF 121.4
i guess it was 18.8 MB/s i made a mistake ;)
I changed the sd to see if that was the problem but the problem still there. The weird thing is that burst in raw is working perfectly, the problem is only with the intervalometer.
Remove SD-card and run ML from CF-card only. Retry.
Quote from: itsDPmikey on April 12, 2015, 04:05:15 AM
Well I'm no expert and can't really be sure what the cause is but I don't think its the card because I have 3 of them and all 3 get the same results. I have 2x 32gb LEXAR 1066X UDMA7 65 and 1 128gb LEXAR 1066x
Also One more thing that makes me think its not the cards is that just last night I upgraded to 1.2.3 and used the latest 1.2.3 build and recorded bunch of diff FRAMERATES and resulutions up to 2.5k wide cinematic ratio and NOT 1 single drop of frame or pink frames or glitch effect(did not test on all cards, assuming would be same results)
Again this is my own personal experience and thoghts that 1.2.3 is more stable and reliable.
But I'd like to get more of your opinion on the defrag situation which I don't think I have ever done. I always format cards IN THE CAMERA when I'm done offloading the files.
Hey guys,
I had a couple of shooting dates and even, as it didn't make problems on the testing, I also got the bad frames problem. Interesting thing is, that it was not only on one frame, but even two frames.
Canon EOS 5D Mark III, EF 28mm f/1.8 USM
1/64 sec, f2.2, ISO 100
1920x490 60.003 fps
Bad frames on different 128 gb Sandisk 160mb/s cards
magiclantern-Nightly.2015Apr06.5D3113
Please I need help, I have more shooting days this week and need to know, if earlier versions were more stable in case of bad frames. Does anybody has experience? I would like to keep firmware 1.1.3 because I don't get contiguous 50p on 1.2.3
https://dl.dropboxusercontent.com/u/24873307/weird%20bad%20frame/M16-2120_000012.dng
https://dl.dropboxusercontent.com/u/24873307/weird%20bad%20frame/M16-2120_000013.dng
https://dl.dropboxusercontent.com/u/24873307/weird%20bad%20frame/M16-2120_000014.dng
https://dl.dropboxusercontent.com/u/24873307/weird%20bad%20frame/M16-2120_000015.dng
@johannsebastianbach All I can tell you right now is to check-out the 1.1.3 March 26th Nightly build been really really stable for & Zero Pink Frames in all shooting settings.
Quote from: johannsebastianbach on April 19, 2015, 07:10:44 PM
Hey guys,
I had a couple of shooting dates and even, as it didn't make problems on the testing, I also got the bad frames problem. Interesting thing is, that it was not only on one frame, but even two frames.
Canon EOS 5D Mark III, EF 28mm f/1.8 USM
1/64 sec, f2.2, ISO 100
1920x490 60.003 fps
Bad frames on different 128 gb Sandisk 160mb/s cards
magiclantern-Nightly.2015Apr06.5D3113
Please I need help, I have more shooting days this week and need to know, if earlier versions were more stable in case of bad frames. Does anybody has experience? I would like to keep firmware 1.1.3 because I don't get contiguous 50p on 1.2.3
https://dl.dropboxusercontent.com/u/24873307/weird%20bad%20frame/M16-2120_000012.dng
https://dl.dropboxusercontent.com/u/24873307/weird%20bad%20frame/M16-2120_000013.dng
https://dl.dropboxusercontent.com/u/24873307/weird%20bad%20frame/M16-2120_000014.dng
https://dl.dropboxusercontent.com/u/24873307/weird%20bad%20frame/M16-2120_000015.dng
Is the frame rate in your Canon menus set to 720p60? I've noticed if I have the Canon menu on 1080p24 or 1080p30 while setting ML to 48 or 60fps I get some corrupted frames.
Quote from: jordanwalkert on April 19, 2015, 07:30:18 PM
Is the frame rate in your Canon menus set to 720p60? I've noticed if I have the Canon menu on 1080p24 or 1080p30 while setting ML to 48 or 60fps I get some corrupted frames.
It's 720p, 60p. Squashed mode. - And btw, the bad frames are happening in about 20% of my clips. I recorded about 50 clips of 12 seconds (until the frame skips) and 10 of my MLV clips were compromised.
Here again, two frames in a row (which doesn't look like it's the cards:
Thanks goldenchild9to5, I will downgrade and write about the differences :)
QuoteHey guys,
I had a couple of shooting dates and even, as it didn't make problems on the testing, I also got the bad frames problem. Interesting thing is, that it was not only on one frame, but even two frames.
Canon EOS 5D Mark III, EF 28mm f/1.8 USM
1/64 sec, f2.2, ISO 100
1920x490 60.003 fps
Bad frames on different 128 gb Sandisk 160mb/s cards
magiclantern-Nightly.2015Apr06.5D3113
Please I need help, I have more shooting days this week and need to know, if earlier versions were more stable in case of bad frames. Does anybody has experience? I would like to keep firmware 1.1.3 because I don't get contiguous 50p on 1.2.3
Are you guys shooting MLVRaw or just RAW? If MLVRaw, try shooting in RAW and report if you get this problem. I haven't seen the pink frames with the latest build of 1.2.3 shooting RAW. I have MLVRaw turned off.
@johannsebastianbach No Prob.. I would also recommend that you set your Shutter Speed to 1/120 - 1/125 for 60p it's a great rule, but unless you want more motion blur than it's clearly a creative choice. Let me know how it goes Cheers..
Hello,
i am a new member here!
So first things first! Hi everybody and thanks for all the work on this wonderfull Firmware!
As a new owner of a used 5D Mark III wich I bought on eBay, I wanted to go for the Magic Lantern Installation
Actually I was on 1Ds Mark II before wich was not compatible with ML, so I am very exited to enjoy all the new Features ML will bring up!
I have one question due to the two Versions of ML for the 5D Mark III (5d.113 and and 5d.123).
The Download Page says the 5d.123 Version is supporting the new Autofocus Features of the 1.4x and 2x Televonverters from Canon.
Is there a major difference in the two ML Versions for the 5DM3? If yes, is there a side by side list of the differences, what is working and what isn't?
I have both Canon Converters and I work with both of them on my 70-200 2,8 IS USM Lens.
Is it good to go wit 5d.123 and have still all ML Features from 113?
Thanks for a quick guidance! I am new. :-)
BR,
derpuma
http://www.magiclantern.fm/forum/index.php?topic=14704
Thank you Walter... Looked everywhere on the Website but not in the Topic of the 5d.113 Thread... :-X
Hey Gyus,
Quick Question is it possible to downgrade from 1.2.3 to 1.1.3?
oh it is ( I searched ) :)
Hey johannsebastianbach,
Thanks for sharing your experience It helps others to see my point.
One of the major problems with this frame issue is that you can shoot a long video and as you cut and edit it ITS very possible that you can miss the pink frames because they are like 1 or 2 frames out of hundreds maybe thousands of frames depending on the length of your video. They are spread out so you have to go frame by frame to locate them and delete them.
In one instance I shot and edited an 8 min video. After finishing and rendering the video and getting ready to upload to internet I watched it and noticed the pink frames and I had to delete the rendered file and re-work on the project again.
So if some of you haven't already I would recommend that you go back and slowly check the frames and make sure a pink frame didn't sneak up on you.
IF YOU ARE USING ML FOR SERIOUS PROJECTS*(JOBS)
I highly recommend using 1.2.3 because it is more stable(reliable). I understand that you might not get the same recording length results but at least you will get usable footage.
I got the same problems too, with my 5D3, using the last ML firmware at 720/60fps but only happens when i magnify the image at 5x with the SET button
at 1920x1080, what i´m doing wrong? is very annoying :(
https://www.dropbox.com/s/ubiyw0pobld8duy/Comp%201_01345.jpg?dl=0
https://www.dropbox.com/s/ecqg0drfim9vrai/Comp%201_01408.jpg?dl=0
https://www.dropbox.com/s/4pdx9dtpz36gju9/Comp%201_01518.jpg?dl=0
That's because crop mode isn't suitable for slow mo's...
30fps is highest for crop mode otherwise you will get all kinds of crazy pink effects.
Is this what your referring to?
I guess you right dude, i´ll try it again, i got here a docen of pink, drop and other annoying raw frames :(
If you tend to use 3x crop mode for RAW/MLV recordings then best to shoot in anything up to 30fps.
Anything above 30fps is a no go.. shoot in regular mode.
UPDATE****
Today I had to do a shoot for baptism at the the river and it was that very beautiful sunny California weather that I'm so use to. Any who, I decided to downgrade to the latest 113(4/27/15 this morning) and try to tackle the issue with this pink/glitchy frame problem. I think I may have found the problem.
I always set my 5dm3 to 1080-30fps and in ML override fps to 23.976. This has been my personal settings and have always worked fine with no issues. The reason behind this method is because I do some shoots that require 30fps for tv and its easier to switch between 30 and 24 In ML instead of going into the canon menu everytime. Whenever I need 30 I turn off override and whenever I need 24 I turn in on simple as that.
Well Apparently FORME this has been the cause of the pink glitch frames. It just kinda came across my mind and I decided to test it out right what the heck why not.
I recorded 3 min with CANON 30FPS with override ON to 24fps and 3 min with 3 CANON 24fps with NO fps override.
As you may already have assumed, the one with override ON came out with pink glitching frames AND the one with no ovveride came out all 4320 Frames came out clean. I did the same test again and got same results. So I now have decided to keep the 113 and not use override in ML and just take an extra second or two and make the necessary changes in the CANON menu.
Well this was my personal experience. If this was helpful to ya I'm glad if not sorry.
Please try this out and see if you get the same results.
THANKS FOR READING!
I noticed, that I got extremely many (same kind of) bad frames, when used 67fps -override, so this could be a indication for it.
I shot for about five days over 350GB with different 113Nightlys, with bad frames almost every second/third MLV's. Now I have one last shooting day ahead this weekend and will test it. Thanks in advance, you will hear from me.
And by the way, for changing the fps in slow-motion. One could switch between NTSC 59,940fps and (in my case) continuous PAL 50.000fps very quickly trough MyMenu Settings.
Quote from: johannsebastianbach on May 06, 2015, 07:51:42 AM
I noticed, that I got extremely many (same kind of) bad frames, when used 67fps -override, so this could be a indication for it.
I shot for about five days over 350GB with different 113Nightlys, with bad frames almost every second/third MLV's. Now I have one last shooting day ahead this weekend and will test it. Thanks in advance, you will hear from me.
And by the way, for changing the fps in slow-motion. One could switch between NTSC 59,940fps and (in my case) continuous PAL 50.000fps very quickly trough MyMenu Settings.
I am going to keep that in mind for tomorrows shoot.
Sort of off-topic but I need to get an external viewfinder/monitor for my 5d. I work on a lot of CGI stuff and being in front of the computer isn't helping my eye condition out. I can't rely on my eyes and the
tiny 5d screen anymore. So before I go and spend some of my moms money, can anyone recommend me a Monitor that obviously has HDMI supports MagicL but also has
dci high end port options because I'm going to probably upgrade to
sf700 or
RedEpic or
C300MII. I don't want to buy a separate monitor If I can just buy one now that I can use later for other cameras.
IT MUST SUPPORT MAGIC LANTERNSo the real question is, Can I get any monitor as long as it has HDMI support? I'm looking at the
Atomos Shogun,
Video Devices PIX-E7,
Odyssey 7Q 4K, and
DP7-PRO OLEDALSO.. I know that some of these monitors also are recorders but I just need a monitor not necessarily looking for recording feature.
Knows someone if a version for 1.3.3. will be released?
Yes
Added support H.264.ini? There was an assembly?
<H.264.ini not found>
Quote from: woron310 on May 07, 2015, 05:34:43 PM
Added support H.264.ini? There was an assembly?
<H.264.ini not found>
This has been an issue with me since first day I got ML which was last year around March. In the video menu of ML, The H.264.ini has always displayed not found for me.
Where can I get H.264.ini for Canon 5D Mark III?
Quote from: itsDPmikey on May 03, 2015, 07:19:23 AM
UPDATE****
Bad news :-[
These are 170 GB of MLV's. I marked MLV's with pink frames red... Its interesting how they are clustered nearby together. Some of the clips even have six pink frames. I tried to figure out if it had something with the aperture or shutter changes but the conclusion is that the bug is very random.
FPS Override was turned of.
My GlobalDraw was turned on everytime I shot, so I will continue testing with GlobalDraw off next time. I think 4000 Frames is not enough for checking :D
I really would like to figure out where the problem comes from :)
btw, should we open another Thread for this problem?
Quote from: johannsebastianbach on May 14, 2015, 08:42:59 PM
btw, should we open another Thread for this problem?
Please do.
Quote from: johannsebastianbach on May 14, 2015, 08:42:59 PM
Bad news :-[
When I turned off FPSoverride out of the 10gb clips I only got 1 single pink frame. But at this point its more frustrating to find out that its really a "random" type of issue.
one more thing that I noticed: When you hit record you will either see a
RED,
YELLOW, or
GREEN camera status icon. I noticed that the clips that end up with the pink frames(other than high FPS) are clips that had either the YELLOW or RED status while recording. Ironically you get
YELLOW or
RED due to HIGH FPS settings.
itsDPmikey: What nightly are you running with 1.1.3?
I recently noticed some pink/bad frames in some clips a shot a while back and wondering which version you were running. Would also be interested in knowing which nightly you are running Alex, as you say you don't experience this issue?
itsDPmikey, I'm not sure that FPSoverride is the issue, as I was running 25fps Canon menu as well as in the ML settings. When I get a chance I'll run some tests and see what I find.
Is there another thread for this issue yet?
Hello all,
I'm just starting out with ML on my 5D3 (1.2.3. with most recent nightly build). My initial results have been great as far as obtaining a wider tonal range but on the downside, I've been getting lots more noise than when I shot simply in H.264 without ML. I've also been getting vertical lines in the shadow areas (as if I had underexposed a high ISO shot by 3-4 stops and brought it back in Cam Raw). My workflow is:
shoot MLV - convert with RawMagic - apply LUT in Davinci Resolve Lite 11 (followed most common workflows on the net) - export to ProRes 4444 - edit in FCPX. I know Davinci Lite has no noise reduction but I've tried the AE/ACR (with noise reduction) workflow and I still get lot's more noise than I'd expect (more than H.264). Any ideas? Thanks!
Dylan418,
I think the latest version of RawMagic fixed the vertical line issue.
Quote from: paisleybrew on May 23, 2015, 04:38:41 PM
itsDPmikey: What nightly are you running with 1.1.3?
I recently noticed some pink/bad frames in some clips a shot a while back and wondering which version you were running. Would also be interested in knowing which nightly you are running Alex, as you say you don't experience this issue?
itsDPmikey, I'm not sure that FPSoverride is the issue, as I was running 25fps Canon menu as well as in the ML settings. When I get a chance I'll run some tests and see what I find.
Is there another thread for this issue yet?
Honestly I always update whenever I see an update available. I will tell you that I have gotten the pink glitch frame on every release since march. Right now I'm on the latest May 2nd release.
I had accidentally deleted some files from my CF card and I used LEXAR Image Rescue 5 that came with it and recovered deleted files. I then had to format the card and decided to read up on the diff format options available and
Exfat is the best so I did an exFAT format on the computer and got the card in to the camera and shot a 17min non stop
1920x1080 24FPS video which
no pink frames. I had realized that I had formatted the cards originally in FAT32 which was limiting the cards to 4gb increments.
Please read more on exFAT and other formats. Also the recording status icon in
fat32 use to be yellow and red in 1920x1080 24fps
With
exFAT its just green! and I even shot over 2K at
2560x1024 24FPSoverride, and it was still green with no skips. This was AMAZING to say the least. So I recommend to get your cards formatted in exFAT
Try this and please let me know how it works out for you.
Running everything up to date. It's more like noise that you get when you try and push color correction too far...
exFAT is a lifesaver... As always!
Hi every one please i have a problem with my new camera and am badly in need of hlep.
I have a Canon EOS 5D Mark III and have never install magic lantern in it. That's becauase
i had installed a 1.3.3 firmware in it and have not been able to get the rite magic lantern for
it please will be very happy if any hleps me thanks.
Go back to the canon 1.2.3 firmware and install MagicLantern. Simple.
I've seen someone who went back to a 20th of Feb build and had no pink frames? I'm going to go with this. Anyone else done this?
Found some interesting behavior for ETTR using the latest nightly for 5D3 1.2.3. When Live View and ETTR are both enabled, and ETTR is set to always on, the camera will push the exposure WAY right after taking a photo. I had the longest shutter speed set to 10" in the settings; after taking a picture the shutter speed had been set to 10" and the ISO had been set to 12,800. This doesn't happen when using the viewfinder.
Any ideas?
Quote from: DeafEyeJedi on May 26, 2015, 06:52:48 PM
exFAT is a lifesaver... As always!
right exactly. I recommend everyone to do so if they have not already.
Talking about pink frames. I am using magiclantern-Nightly.2014Aug07.5D3123 Recently on a Shoot i had to record roughly 4 mins of footage (6000+ frames) was recording at a resolution of 1920x768 (aspect ratio 2.50:1) FPS 23.927 NO FPS Override.
not a single Pink Frame.
So far this nightly build works a treat. I would suggest users who are experiencing Pink Frames to try using that version.
Does anyone have the Canon 5d Mark iii mac firmware files 1.1.3 or 1.2.3? I currently have 1.2.1 and cannot install ML. If I update to 1.3.3 I still cannot install ML. Any help would be appreciated!!!!
Sorry for the dumb questions but I still have some:
- Do I install ML on an SD card and put the extra fast CF card in the second slot? Or do I forget about the SD slot and everything goes in the CF?
- Is the uninstallable bootflag modification still present in both 1.1.3 and 1.2.3? Or is it possible to completely and cleanly uninstall ML in both firmwares?
I'm mainly trying to decide whether to go with 1.1.3 or 1.2.3. I won't need the official Canon things in 1.2.3 but there's some extra info in the 1.2.3 thread that isn't present here and I just want to make sure the 1.1.3 also have these options (clean uninstall, optional EosCard, ML restores itself after format etc).
Quote from: italobrito on June 09, 2015, 07:20:37 PM
Sorry for the dumb questions but I still have some:
- Do I install ML on an SD card and put the extra fast CF card in the second slot? Or do I forget about the SD slot and everything goes in the CF?
- Is the uninstallable bootflag modification still present in both 1.1.3 and 1.2.3? Or is it possible to completely and cleanly uninstall ML in both firmwares?
I'm mainly trying to decide whether to go with 1.1.3 or 1.2.3. I won't need the official Canon things in 1.2.3 but there's some extra info in the 1.2.3 thread that isn't present here and I just want to make sure the 1.1.3 also have these options (clean uninstall, optional EosCard, ML restores itself after format etc).
You can either split the process like so
. Put ML on SD card and use the CF card for recording files (this is highly recommended and easy to set up in the ML menu).
or
. If your SD card is fast enough with enough space you can put both the ML and set to record files on the SD as well. (not recommended. Only if you have no CF option and only have SD card)
*Yes its possible to completely and cleanly uninstall ML in both firmwares. Whether you are on 113 or 123, when you enter in canon menu to update firmware(while firmware card is in the camera) Install ML and when it installs and says "done", At that point it will start to count down. IF you want to uninstall let it count down all the way and that will uninstall it. THAT'S IT.
currently there are some issues with the 113 with pink frames and whatnot, but this wasn't always the case its only been happening in the most recent builds(have not tested the June build yet)
123 is steady but lacks some options so it depends on what you are doing.
I have formatted my CF card in exFAT and I'm using 1.1.3 again, everything is good for me so far.
itsDPmikey, thanks a lot, you really helped. I was mainly thinking about 113 because it's said to have slightly faster write times but I already have a sufficiently fast CF card so I guess I'll stick with 123.
Just one last thing, should I format both the SD and the CF in exFAT or do I leave the SD card with ML in FAT32?
Thank you very much.
Quote from: italobrito on June 12, 2015, 06:52:48 AM
itsDPmikey, thanks a lot, you really helped. I was mainly thinking about 113 because it's said to have slightly faster write times but I already have a sufficiently fast CF card so I guess I'll stick with 123.
Just one last thing, should I format both the SD and the CF in exFAT or do I leave the SD card with ML in FAT32?
Thank you very much.
Yes but it is not necessary due to the fact that
ML FIRMWARE files don't take much space at all and don't require very high speeds. It's more the CF(or the card that is being recorded on) that really improves when you format to exFAT.
The maximum file size for FAT32 is 4gb, which if you record in raw and depending the FPS and resolution size, you will pass 4gb very quickly like around 5min or less. This is why FAT32 is not recommended.
exFAT allows a
maximum file size of 16eb. That's 16 EXABYTES! As in 16
QUINTILLION, As in
16,000000000000000000...so as you can obviously do the math that's an incredible amount of difference.
So theoretically if you have a card that is 4gb or less, it's not really necessary. But
OBVIOSULY if it's a card with more than 4gb space then yes exFAT that lil sucker!
New 5D3 firmware on June 9th. Change log seems to be blank. Anyone who about this release?
lostfeliz:
Just download and test it for yourself -- that's what we all do for a living, right? [emoji6]
If not happy with it then simply go back to whatever nightly you prefer.
Hi i'm stuck with the same problem it seems you were but I cannot see that it was answered. Please can you advise how you overcame the problem of not beiiing able to download the modules for RAW recording etc. I do not have the 'M' tab just a triangle.
Your assistance would be greatly appreciated.
YBB
There is no tab labeled "M". Browse tabs until "Modules" is displayed.
Modules tab will not be seen after crash. It's there after restart following clean cam shutdown.
June 9th firmware for 5D3 1.2 3 seems to have been removed!
Quote from: tron on June 18, 2015, 03:21:53 AM
June 9th firmware for 5D3 1.2 3 seems to have been removed!
This is Correct. But I did download it before it was removed
Quote from: itsDPmikey on June 19, 2015, 08:14:33 AM
This is Correct. But I did download it before it was removed
I'm going to correct myself. I misread the comment, I do not have 1.2.3, I for some reason saw 1.1.3. sorry for the confusion
Please, looking for firmware 1.2.3! does any one can tell me where to download it anymore? (I've looked everywhere, but I did'nt find it. I looked also at webarchive...)
First page, first post. Or top of page -> Downloads -> Download nightly builds -> 5D3.123 and read instructions.
Question... what does the yellow camera icon mean before it turns green?.. is that just it waiting for start frame?
Green = continuous recording possible at current rate
Red = continuous recording not possible at current rate
Yellow = borderline situation
Thanks Frank
It would be nice if it showed when it actually starts recording instead of red/yellow/green stuff.
Quote from: 5Djp on June 22, 2015, 06:12:36 AM
Thanks Frank
It would be nice if it showed when it actually starts recording instead of red/yellow/green stuff.
It starts recording when the countdown or count-up starts. When the timer starts then it starts recording.
Will ML run on 1.3.3 yet?
Since there's a thread for firmware version 1.1.3, and firmware version 1.2.3, but no thread for firmware version 1.3.3, I'm going to go out on a limb, take a rough guess at no.
Quote from: actingnurse on June 22, 2015, 11:07:04 PM
Will ML run on 1.3.3 yet?
NOThe 1.3.3 firmware [b]also known as the[/b] AMLF(Anti-MagicLantern Firmware) by CANON, was produced in efforts to [b]STOP [/b]people from using MagicLantern.
What does AMLF 1.3.3 actually fix/do? Well lets take a look at what CANON has to say.
[b]Details http://www.usa.canon.com/cusa/support/consumer?pageKeyCode=prdAdvDetail&docId=0901e02480e37761
Firmware Version 1.3.3 incorporates the following improvement and fix:[/b]
"[i]Improves the AF controllability when shooting in Live View mode with a wide-angle lens (fixed focal length or zoom).
Corrects some incorrect indications on the "English" and "Russian" menu screens.[/i]"
...thats it? Yes that's it.
In other words, this firmware update is absolutely useless. [b]BUT[/b]! What CANON did not include in this release details was that they wrote this firmware strictly for MagicLantern users to stop us and you don't have to be a "brain surgeon" to understand this.
One of the things CANON [b]DID NOT[/b] [s]disclose [/s]is that with this new firmware you can't downgrade, at least not as easily as you could before, now you need to be on the computer and have it connected to the Camera. In reality this is not too different from what Microsoft was trying to do with Xbox One, taking the rights away from the people.
One of the most Obvious things about CANON is that they [b]OVERPRICE [/b]their products. Primarily their cameras.
You can [b]accomplish [/b]just about [b]anything [/b]with 5D if not more than lets say the c100 and some of the CANON'S other high priced cameras.
For this primary reason, CANON has tried to find a way to stop the MagicLantern use on their cameras.
Consider what you can do with some of the lower end EOS cameras with MagicLantern installed, some INCREDIBLY WONDERFUL things. So you may just ask yourself.. why spend thousands when you can spend hundreds for the same thing if not BETTER! this obviously isn't something that CANON finds favorable.
Instead of lowering the prices of their cameras to reasonable prices, they continue with their foolishness by taking away from the people what BELONGS to the people.
If I paid for it and now its mine, I should be able to do whatever I want do with it. Right? I guess CANON doesn't think so.
I've blabbered on enough about this.
All in all, you are [b]NOT[/b]! missing out on anything by not installing a useless update like 1.3.3
Using EOS Utility will allow downgrading from 1.3.3.
You can download EOS Digital Solution Disk 29.1A from Canon's support site and install EOS Utility.
Please keep Canon rants in the general chat section, or preferably some other site.
Can anyone tell me why even though I have 'Frame Skipping' turned off, once I convert my MLVs do cDNGs and import them to After Effects, I occasionally get a message telling me there's a missing frame in my footage?
So far it's only one single frame per video and when I look for it, the actual file isn't there (it goes from something like M25-151800026.dng to M25-151800028.dng).
That's weird because when recording, the camera/recording icon often shifts from Green to Yellow but it absolutely never becomes Red and the camera never stops recording.
I'm having a hard time figuring out if that's my card having issues to keep up or something else. I also wonder why ML isn't stopping the recording once it skips a frame.
@italobrito:
Which converter did you use?
@DeafEyeJedi:
It was raw2cdng.1.7.4, using the default setting of 'CNDG 12bit maximized' and no other option.
Not sure if that converter can spit out DNG's instead of CDNG's? Or try an earlier version of raw2cdng?
I'm mainly a Mac user here and perhaps you can wait until @chmee gets back to you.
Have you tried the windows version of 'MLVFS'?
@DeafEyeJedi:
Thanks for the help. I googled a bit more and found out some other people having the same issues with the 1.7.4 version of raw2cdng, they said the 1.6.5 version works well, apparently. Hopefully everything will be fine now. Cheers.
Anyone know why magiclantern-Nightly.2015Jun09.5D3123 (Nightly build 2015 Jun09 5D3123) was pulled for the 5D MKIII with 1.23 firmware? It's seems to have worked. I still have it loaded on my camera.
Does anyone know why?
This is not specifically about that build but all I could find on this site was a "Reply" button and not a "Post"! My question though is that suddenly my screen does not show any of the ML control overlays! Nothing, nada, zilcho! Not even the red recording indicator! I haven't touched a thing and suddenly it's all gone, any suggestions on how to get it back?
and pressing 'info' didn't help? Is ML still on the card?
Can someone provide a link to the 1.2.3 firmware? The link on the ML 5D3 1.2.3 download page seems to be broken.
Thanks!
Retry. Pelican's site is online again.
why in the hell is davinci resolve crashing upon selecting magic lantern raw files.
https://youtu.be/A-giOSQH2Fc
Hi All,
Forgive me not being exactly on topic, but I want to gather the ML users in Burbank, Ca Oct. 3, 2015 for a symposium about ML, workflows, successes and challenges.
I've had great success with it and want to spread the word of how ML makes the most of 2k. Today I named it ULTRA 2k.
(in daylight, low ISO)
https://vimeo.com/74455311
(blonde in black silk, hi ISO)
https://vimeo.com/77717260
Please advise where I should post this. I really just want to see Magic Lantern is a success.
Nice work fletch_cinebootcamps.
It's be nice to see what you are doing. I did some projects years ago with Randy at the Association.
You may post this under "Share Your Videos (http://www.magiclantern.fm/forum/index.php?board=19.0Share%20Your%20Videos)" section for future references but Thanks for sharing anyways.
I also like to see someone not being afraid to push the blacks down... It's so nice and which ISO did you use for the 2nd clip?
Please kit regarding symposium updates and would definitely love to attend.
Quote from: itsDPmikey on August 08, 2015, 07:38:02 AM
why in the hell is davinci resolve crashing upon selecting magic lantern raw file?
That's probably due to the Hollywood Gods preventing us from a breakthrough with the colorgrades from MLV RAW that DR produces....
Kidding but I am experiencing the same exact issues on both of my Mac's which doesn't have a decent graphic card installed in order to hold up with the GPU hungry app in DR.
Though admittedly I haven't tried the newly released Beta DR 12 version yet.
However, I'm happy with how AE (ACR) gives nice debayering results regardless of its slow process in the workflow.
"That's probably due to the Hollywood Gods preventing us from a breakthrough with the colorgrades from MLV RAW that DR produces...."
Try processing the MLV Raw with RAWMagic first. This will make a folder of RAW CinemaDNG files (all RAW). Bring into Resolve and voila. Works here!
Off topic:
Is there a reason why you rather use RAWMagic besides the other decent converters that give proper required tags unlike this one?
Even if it's not supported by ML?
http://www.magiclantern.fm/forum/index.php?topic=11879.0
Resolve 12 beta works fine for me with raw2cdng.1.6.5 CinemaDNG. That guy need a proper videocard, or quicktime installed, maybe windows 10 is the problem, or, finally, straighten hands... And why this discussion here?
RawMagic works for me without issue. I shoot Raw not MLVRaw.
About RawMagic -> Official statement about ML's GPL license and its violation (http://www.magiclantern.fm/forum/index.php?topic=13335.0)
I am getting latency when shooting on the 5d Mk3 using a SmallHD external monitor (HDMI connection). Is there a way to eliminate this?
Canon had removed 5D3 firmware 1.2.3 on their website. where can I get/download firmware 1.2.3? do anybody here having it and can I get it from you?
Read first post.
I read the first post and the link is to canon's site. They don't have 1.2.3 available for download there anymore just 1.3.3. If anyone has a working link they can share it would be greatly appreciated. I've been searching as well.
Top of page -> Downloads -> Download Nightly Builds -> 5D.123
Go to downloads > download nightly builds > 5D3 1.2.3 > now scroll down to bottom where it says "Installation" and under there should be a highlighted link to the actual firmware 1.2.3.
Please read thoroughly!
Thanks! Sorry I was a little confused.
Hi everybody,
Is anyone able to provide for me the firmware 1.2.3 (5D300123.FIR) for my EOS Canon 5D mark III cuz i upgrade my camera with the last firmware 1.3.3 (5D300133.FIR) that don't allow the ML installation.
Thank you in advance for your help.
Best regards.
Greg.
Seriously?
Perhaps read a few post above this and maybe you'll find your answer?
Hi Guys,
I've read this entire thread. I currently have a 5D II with ML installed (thank you!) and will be getting a 5D III soon to put ML on it. As far as I can discern the general consensus in this thread is to go with the v1.1.3 firmware and ML build over v1.2.3 but both nightly builds have been updated quite a lot since a1ex posted this thread back in March 2015:
http://www.magiclantern.fm/forum/index.php?topic=14704.0
May I just ask, is it still the general consensus to go with v1.1.3 over v1.2.3? I won't be doing much (if any) slow-mo shooting and will be predominantly shooting 23.976 the whole time. If I do need slow-mo then it'll be subtle so I'll probably just use a higher shutter and Twixtorize it in post.
My prime concern is stability and having no pink / corrupted frames (something I've experienced on the 5D II but have overcome by turning off Global Draw when recording and using a mask on my Viltrox DC-70 HDMI field monitor to frame the shot) but unfortunately this thread seems split between which is more stable. Some citing v1.1.3 as the most stable, others the opposite.
Obviously, my other prerequisite is to be able to use my HDMI field monitor without issue. I take it that's nothing to do with v1.2.3's ability to output "clean" HDMI and v1.1.3 will still output to a field monitor with no problems?
So, what's the general consensus now, at this moment in time, with regards to which build and firmware to go with?
Cheers,
Mark.
Quote from: markodarko on September 22, 2015, 07:32:26 PM
Hi Guys,
...
My prime concern is stability and having no pink / corrupted frames (something I've experienced on the 5D II but have overcome by turning off Global Draw when recording and using a mask on my Viltrox DC-70 HDMI field monitor to frame the shot) but unfortunately this thread seems split between which is more stable. Some citing v1.1.3 as the most stable, others the opposite.
Obviously, my other prerequisite is to be able to use my HDMI field monitor without issue. I take it that's nothing to do with v1.2.3's ability to output "clean" HDMI and v1.1.3 will still output to a field monitor with no problems?
So, what's the general consensus now, at this moment in time, with regards to which build and firmware to go with?
...
According to this page, http://builds.magiclantern.fm/#/ (... and selecting the "5D3.123" option)
You should use the Canon v1.2.3 firmware and compatible Magic Lantern software overlay if you need:
"1) Clean HDMI out (ziggy note: This means if you want clean HDMI Out for the purpose of recording the HDMI output onto an external HDMI recorder.*)
2) Dual monitor support
3) AF at f/8 with teleconverters"
If you don't need those things, stay with Canon firmware version 1.1.3 and compatible Magic Lantern overlay. Yes, Canon firmware version 1.1.3 will output to the HDMI port a viewable signal with an external monitor, but the monitor will also display additional camera information.* It will not generally be a preferable video signal to record for editing and color grading purposes.
-------------------------------------------
*OK, the Clean HDMI signal is also a better video quality, as well as not having any additional camera information. For an explanation of the differences:
http://alikgriffin.com/blog/may/04/what-does-clean-hdmi-really-mean-5dmkiii
with my 5D3 plus the 1.2.3 firmware from august 2014 I never had one single corrupted frame! With my cam, is working perfectly
Hi,
I am very new to ML, infact I have not loaded it at all, anywhere.
I have a Canon 5d Mk111 that has ver 1.3.3. firmware, the latest.
The latest that ML supports is ver 1.2.3, I think.....
If I am on the right track is there a ML version for canons newest firmware, as I can't go back to an older version of firmware (Can I?)
Unfortunately I am crap at programming, never got my head around BBC basic, how dumb is that...
But this Magic Lantern by all accounts is not something to be ignored.
So if anyone knows if there will be a version coming sometime I would be very interested.
Thanks for reading
Geoff
You need EOS Utility v2.x. If you have v3.x installed you may want to get rid of it and download EOS Digital Solution Disk v29.0A or v29.1A from Canon's support site. Download Firmware v1.2.3 or 1.1.3 (both versions are supported and have their pros and cons) using the links provided in Downloads -> Download Nightly Builds.
Connect your cam (photo mode M preferred) to your computer and downgrade via EOS Utility.
Hi guys !
i'm tryin to install ML on my 5DIII which is in 1.2.3 version.
downloaded 5D3.123 ML version.
and when i try to update firmware i got an error message that says i have to go back to 1.1.3...
why ?
Looks like you downloaded ML for 5D3.113 and this version is dedicated to firmware version 1.1.3. You need ML for 5D3.123.
Please check file name.
i just check it.... and no, it's ML5D3123.fir
Format card in cam, download and extract Canon's original firmware file v1.2.3 to card (use link in download page) and run firmware update.
Wipe file from card, copy extracted nightly build contents to card and run firmware update.
Results?
Is there a clean list of what features this build of ML has over the stock Firmware? In respect to the 5d Mark3.
I have a T3i, and I know for that camera it opens up many features, but the 5d has many more builtin features over the T3i that fill in the gap of what ML offers.
Thank you in advance.
Maybe this will help you?
http://ultraview.ru/sites/default/files/imce_files/raw_dlya_canon_magic_lantern.png]http://ultraview.ru/sites/default/files/imce_files/raw_dlya_canon_magic_lantern.png]http://ultraview.ru/sites/default/files/imce_files/raw_dlya_canon_magic_lantern.png (http://ultraview.ru/sites/default/files/imce_files/raw_dlya_canon_magic_lantern.png)
Hi everyone, I'm new here.
It's my first day with Magic Lantern into my 5D3, and I had a movie recording stopped automagically message (when I tried to shoot in crop mode).
This is my set:
-firmware downgraded to 1.2.3;
-2015Apr28 Nightly Built;
-SanDisk Extreme Pro CF 256GB (ExFAT formatted via OSX Utility Disc - NOT in camera) and this is the UNIQUE card in the camera (ML files are stored in the root directory) so the card is in SLOT 1 (so no Low Level Format option possible);
-Canon Menu: Movie rec. size 1920x1080 24p ALL-I;
-Magnification: x5 (ISO and STOPS change into red on the screen);
-ML Menu: Movie > RAW video ON, 3584x1320;
-lens: 35mm f/2.0 IS USM (in ManualFocus mode, but with stabilizer ON).
I press Start button (camera icon on the screen is red) and immediately arrives the message: movie recording stopped automagically.
I tried other resolutions (always with x5 magnification): 2048x1152 gives me 8 or 9 seconds, then again the stopping message (ISO, STOPS and Camera icons always red).
I tried also 1920*1080 in crop mode: 30 seconds with Camera icon yellow, after that icon becomes red, and at 40 seconds again the stopping message.
In FullFrame mode (simply without magnification activated) the Camera icon is green and all works fine.
What could be the issue in crop mode? Perhaps the CF card is not fast enough? (But it declares 150MB/s writing.) Could it be the NOT-in-camera formatting method I used? Perhaps 256GB is too much for the CF card? Could it be something I didn't set correclty in ML menu? Something else?
Please, I hope you want to help me. Thanks.
I thought I read somewhere that the larger cards have inconsistent results. I have been using and old 1000x komputerbay 64 gb. Works great. Need to stock on those if there still recommended. Also lexar has so good 64gb cards too. One other thing that will help is on the 5d3, its best to run ML off and SD card. Oh yeah and with 3k, you wont get many frames. Maybe this will help.
Does someone has a copy of Canon's 5D Mark III original 1.2.3 firmware? I just can't find it on the internet anymore not even on ftp servers - seems like Canon wiped it everywhere. The only links I've found are scam. I can only find 1.3.3 Thank you!
Btw. this site seems like it's down: http://pel.hu/eoscard/
Hi,
I've just installed the ML in my canon 5d mark iii, And at the beginning it's all right, but when I want to put the second card in the second slot, the camera doesn't works.
I read that you have to introduce the compact flash when the camera say please restart your camera in green color, so turn it off and put the memory card. But in this moment I did and it doesn't turn it on.
The camera never turn it on with 2 memory cards.
Do you know what can I do?
Thanks for all.
@danielschweinert -- Please read thoroughly...
http://www.magiclantern.fm/forum/index.php?topic=11017.msg153950#msg153950
Pel.hu is down and this is the very location (and the only one) where ML instructions have links to "older" firmware files.
Quote from: unfilmdeAnyone know why magiclantern-Nightly.2015Jun09.5D3123 (Nightly build 2015 Jun09 5D3123) was pulled for the 5D MKIII with 1.23 firmware? It's seems to have worked. I still have it loaded on my camera.
Does anyone know why?
I was actually wondering the same thing. I went to check the 5D3.123 nightlies and noticed not only has the June 09 build been pulled from the menu, the last available 5D3.123 build is from April. unfilmde's post was the only one I could find that mentioned that build being pulled. I also still have the June 09 2015 build for 5D3.123 running on my camera.
I apologize if I've missed something, but has anyone said why that build was pulled or why the 5D3.123 build hasn't been updated since?
http://pel.hu/
seems OK now...
I needed to update my camera from 1.1.3 to 1.2.3 (need AF with F8).
But I'm missing some features from 1.1.3 ML builds, unless I missed them in the menu - can't find the fine tune for the live view image, like contrast and saturation boost. Was very helpful when shooting flat (Cinestyle pic profile).
That's one of the reasons I still keep the 1.1.3 build as well (I'm missing them too, which is why I'm running 1.1.3).
I've updated the 1.2.3 source code, but I'm too tired to test it. Can anyone with compiling skills take a look at it, before enabling the next nightly build?
Things that might require attention:
- Canon bottom bar should not conflict with ML's (behavior should not change from past builds)
- changing picture style settings from ML, including the "Auto" picture style
Other things worth mentioning, since last build:
- Diffraction-aware DOF info (http://magiclantern.fm/forum/index.php?topic=15092.0) (garry23)
- Fine resolution control in mlv_rec (https://bitbucket.org/hudson/magic-lantern/pull-request/627/added-fine-control-on-top-of-x-resolution/diff) (rbrune)
- AF/MF warning (http://www.magiclantern.fm/forum/index.php?topic=15258.0) (Andreasb242)
- New installer (https://bitbucket.org/hudson/magic-lantern/pull-request/631/new-installers)
Most other changes were either small fixes, refactorings, or things concerning other cameras.
Thanks a1ex!
Everything seem to works like a charm! :)
I need to test all picture style and sync them with LR but to tired to try it now!
Thanks for all!
Maybe I forget to merge something, but no full-res for silent picture. An idea ? I forget something, no double level and more, too long that I've not compiling ML :o
Just because I'm not clear on the terminology, does "- no full-screen magic zoom (I never used it anyway, but was nice)"
mean that when you press the 5x or 10x zoom button (for critical focus) that you can no-longer record in that mode? Just asking because I was looking to try it out and rather than dig around trying to find a post somewhere on this huge forum, I just thought I'd ask if that's okay?
Cheers, MP
@Mysticpuma:
No, it doesn't. "Magic zoom" is something that popups on screen when you rotate focus ring in manual focus mode and in crop mode is pretty useless, imho.
Thanks for the reply, very much appreciate it.
In that case, is there a way to record video when in the 5x/10x zoom mode? If there is can someone post a link on a "how to"?
Cheers, MP
How to record: -- RAW Digital Cropped Video 30/24fps on 5D3 & others (http://www.magiclantern.fm/forum/index.php?topic=5441.0)
Hi MagicLantern 5D Mark III users,
I just got a hand on a 5D Mark III. I checked the firmware one board and it says 1.3.3... Can I still load MagicLantern 5D3.113 from this link? https://builds.magiclantern.fm/#/
Please let me know here or via PM. Thank you!
You have to use EOS Utility v2.x to downgrade Canon's firmware to v1.1.3
Oh? I heard that people say that it does not work. I can give it a try though...
Says who?
Sean, you will find tons of BS about this in the web. No use to talk about it.
Yes, I know but I just was implying that it is possible. Not trying to be difficult.
Why there is no port for 1.3.3 yet?
I saw some old threads about it's port, but are date in march or so, and besides the date, those threads were quite positive about it's portability, but suddenly I can't find any information about it and there is no port.
Also, why the latest compilation of the 1.2.3 is from April? I woudl like to acquire an external monitor/recorder to have a backup of all the footage (I record in RAW but I would like to record also in the monitor through HDMI) but it seems there is no up to date build for the 1.2.3.
Just asking because I can't find all this information in here while looking for it.
Cheers and thanks in advance!
BTW my 5D mkIII is a new one that came with 1.3.3 an d I was able to downgrade without any problem to 1.1.3 using EOS utility, just FYI :)
It's not perfect and I'm always wanting improvements too, but I use the April software with 1.2.3 so I can use an external monitor (focusing without it is to hard) and rarely have an issue.
I assume the lack up updates is because they are working on some big new things, which may or may not have anything to do with the 5Diii.
Hey Guys, i am searching for a whole bunch of time now. Like a big bunch of people i have this Pink Frame issue. Can someone tell me if there is a fix?
i read about turning of focus peaking. is there maybe another solution? Did someone find something out jet?
Hi monky.
I'm not having this problem at all, I just saw it in one shot while using mlv, I use the hardware focus peaking (the one that uses extra sharpness in the focused area) and I disable any drawing in the live view, plus right now I'm recording in RAW instead of MLV and without sound, I use an external audio recorder, and from what I can see in the screen I achieve a sustained writing rate of 101Mb/s more or less.
So maybe if you do all that you may get rid of the pink frames :)
@lostfeliz what things are not working correctly with 1.2.3? I'm planning in acquiring an external monitor as a review/backup system and I assume I'm gonna need to upgrade to 1.2.3
Also, let me ask for a newer build for 1.2.3 please :) (to anyone with the ability to do that reading this)
Cheers!
Hello,
i kinda searched everywhere for the answere but i can't find anything about it. Is there any possible way to use audio remote shot on the 5d mark III? It's a feature that i want to use for an experiment and i really loved ML since i installed it. It would be awesome for me. Maybe this question and the answer is already on this forum but don't hate me, i searched alot with no success.
Top of page -> Downloads -> Download Nightly Builds -> Features -> Shoot.
New build. I've only tested the changes on 1.1.3, so you may want to wait for some feedback before upgrading.
What's new, since last 1.2.3 build:
- Histogram tweaks (https://bitbucket.org/hudson/magic-lantern/pull-requests/667/histogram-tweaks)
- Diffraction-aware DOF info (http://magiclantern.fm/forum/index.php?topic=15092.0) (garry23)
- Fine resolution control in mlv_rec (https://bitbucket.org/hudson/magic-lantern/pull-request/627/added-fine-control-on-top-of-x-resolution/diff) (rbrune)
- AF/MF warning (http://www.magiclantern.fm/forum/index.php?topic=15258.0) (Andreasb242)
- New installer (https://bitbucket.org/hudson/magic-lantern/pull-request/631/new-installers)
- a few minor fixes
Too early to say Merry Christmas? :P
A very nice gift for Christmas, A1ex. Thanks - again. And - No. It's not too early in Denmark, so I wish you and your family a very good Christmas - and of course the greetings of the season expand to everybody in the ML community.
THank You @a1ex, you are Santa Clauss... ;)
Yaaaaaaaaaay!
Alex, you da man! I am leaving for work now but will download and use it on my camera this week.
Ooooooo the new installer dumps rom and has you save it somewhere! I don't know all the under the hood details but would that make it easier to recover if someone messes up the install?
Yes, that's the idea. I hope we'll never have to use them, but... just in case. Before, the ROMs were saved silently under ML/LOGS (and it's still done whenever the ROMs are not found there, for example, after you format the card).
So far I've reflashed my 550D and 60D with ROMs from other users, and then back with my original ROM, so there are some chances for this to work, if anything goes wrong.
Great.. thank you for all your work @a1ex
Thank you very much for everything. Season greetings to everyone and happy ML 2016
a1ex! I just learned something new! That's amazing! Thank you!
Alex thank you very much and Merry Christmas too. It was a nice surprise :)
I might be misunderstanding what Alex originally posted but is bootflag solved for 1.2.3 AND 1.1.3? Or just 1.2.3?
Yes for both 113 as well as 123.
Does some one has the plan to make a port for Firmware 1.3.3?
Yes.
Is it foreseeable when it will be there?
No.
Is there an essential feature in 1.3.3 you will be missing working with 1.2.3?
So is there any reason one would choose 1.1.3 over 1.2.3 now?
I see it's still recommended when you choose to download 1.2.3
http://www.magiclantern.fm/forum/index.php?topic=14704.msg142089#msg142089
Quote from: lutz-w on December 26, 2015, 06:05:10 PM
Does some one has the plan to make a port for Firmware 1.3.3?
https://bitbucket.org/hudson/magic-lantern/pull-requests/605/support-for-5d3-firmware-133/diff
Awesome thanks!
QuoteIs there an essential feature in 1.3.3 you will be missing working with 1.2.3?
My 5d came with 1.3.3 and i don't want to make a backdate
Will be hard to motivate anyone to port it to 1.3.3 when 1.2.3 are so stable and 1.3.3 doesn't include any new features. Downgrade if you want ML...
Thanks a lot!
I have a 5dIII-113 and a 5dIII-133, downgraded to 123 without any problems. Hey, you can always upgrade to 133, once (if) ML becomes available. The reason it's not here yet may be, that 123 is good enough. I have one of both, just for comparison, and when I feel, that I know enough, I might downgrade all the way to 113. The up/downgrade doesn't disturb me, since I'm convinced it won't interfere with product warranty.
I just turned 63, and when I can do it, you must accept, that the process is very much foolproof.
Rofl! About your last sentence. :)
After being a very satisfied user of ML on my 7D, I would like to install it on my 5DIII, but because of warranty I was wondering if there is a possibility to disable the bootflag.
Is simply updating to the normal Canon firmware enough and if not, does some of you guys have experiences with warrenty-issues and ML?
THNX! :)
@Peatsmoke Yes you can.. I have Magic Lantern running on my 5D mark III Recording RAW Video for 6+ months now no problems not even one Pink Frame yet. I know for ver 1.1.3 it's soo.. easy to install, and very easy to uninstall I've done it a couple times Ver 1.2.3 is a bit different. From my understanding & from what I've read you should be fine with Warranty because Magic Lantern Runs on the SD Card.
http://wiki.magiclantern.fm/faq#does_it_void_my_warranty
There had been some cams sent to official support sites with bootflag set and none made legal trouble.
Updating/downgrading with original firmware won't change cam's bootflag. You can test it on your 7D.
For uninstallation follow instructions in first post.
I'm just so happy with my two lanterns 113 and 123 - thanks, A1ex once again, you sure know how to give Christmas gifts - and I just want to wish all of you a very happy New Year.
The awards having ML far outweighs any warranty issues. I have been through all the threads on this site, and never once heard or read about somebody losing their camera warranty because of a set bootflag.
Once more: Happy New Year to everyone; I'm very much looking forward to visit ML Universe come 2016.
@goldenchild9to5 I might hope I'll be able to run ML from my CF-card, because CF cards have much higher writing-speeds as the SD.
That makes no sense ... Just simply run ML off a decent SD card and that way you can get the most out of recording onto CF (w speeds of at least 1066x) card separately.
My cams are set up so that JPEG go to SD (where ML resides), RAW + Video go to CF card. P119 in the Canon User Guide. Happy New Year all of you.
@Peatsmoke Just like @DeafEyeJedi said best to run ML on a decent SD so the RAW Files can be recorded separately on the CF Card. Trust me DeafEyeJedi knows what his talking about he has helped me out soo much. @axelcine Happy New Years to all & ML Lantern team @A1ex thank you for all your work making RAW a reality for all, I really appreciate that. All my ML users Let's create beautiful images with the 5D3 for the new year 8) If you are down reply with a big "Yes"
I just read through 5 or 6 pages on this thread and couldn't find any information. I also tried searching and oddly, couldn't find the info either.
I currently have 1.1.3 running a Feb 2014 build of magic lantern. I'm shooting a live event coming up, so I will need Canon firmware 1.2.3. What's the best way to update to Canons new firmware? Can I simply overwrite the ML firmware currently installed with Canons 1.2.3 and then reinstall ML after? Or do I need to reload Canon 1.1.3, then upgrade to 1.2.3, then install magic lantern again?
Quote from: ckrieg on January 02, 2016, 08:31:04 PMI'm shooting a live event coming up, so I will need Canon firmware 1.2.3.
How exactly does an upcoming live event force you to update to Canon firmware 1.2.3?
Quote from: ckrieg on January 02, 2016, 08:31:04 PM
What's the best way to update to Canons new firmware? Can I simply overwrite the ML firmware currently installed with Canons 1.2.3 and then reinstall ML after? Or do I need to reload Canon 1.1.3, then upgrade to 1.2.3, then install magic lantern again?
You can not overwrite ML with Canon firmware because ML does not change original firmware and does not replace Canon's stuff.
If you have to upgrade Canon firmware there are several ways to do it. Do you have a spare card (< 32 GByte)?
Quote from: Walter Schulz on January 02, 2016, 08:40:52 PM
How exactly does an upcoming live event force you to update to Canon firmware 1.2.3?
I question this as well...
Quote from: Walter Schulz on January 02, 2016, 08:40:52 PM
How exactly does an upcoming live event force you to update to Canon firmware 1.2.3?
Sorry, I didn't make that very clear. It is live streamed to projectors and monitors for the audience to watch. I will need a clean output while still being able to see what I'm shooting on the back of the camera. This requires 1.2.3, doesn't it? Or am I missing something?
Quote from: Walter Schulz on January 02, 2016, 08:40:52 PM
If you have to upgrade Canon firmware there are several ways to do it. Do you have a spare card (< 32 GByte)?
I have a 32GB SD card that I run ML lantern on. and I have old CF cards that are really small. 4, 8, and 16 GB.
Thanks for the help!
Take one of the "old" cards.
Format card using your cardreader.
Format card using your cam.
Insert card into cardreader and copy Canon's original firmware file 5D300123.FIR to card.
Insert card into cam and run firmware upgrade.
Remove card.
Take your 32 GB card, insert into cardreader and backup ML directory and autoexec.bin and *.FIR.
Remove ML directory, Autoexec.bin and *.FIR from card.
Copy extracted nightly build contents (ML for 5D.123!) to card.
Insert card into cam and startup. Done.
Fantastic! Thank you!!
@Walter:
Today it's gonna happen... Maybe you could give me the right workflow for me?
I have a formated 8GB SD-card for the ML files and bought 2 fast 32 GB CF-cards (by urbex I will be able to change CF-cards when I'm catched by ownes/security).
What is the right way to install ML for me?
Danke für deine hilfe. ;)
Read first post on first page.
Dear All,
I am going to install first time Magic Lantern on my Canon 5D Mark iii . I have firmware 1.2.3 on canon. I just download the Nightly Builds (5D M3. 123). In my Magic Lantern folder I have only two files and one folder, ML Folder, autoexec.bin and ML.SETUP.FIR
My question is i need only these three things or any things else. It will be highly appreciated some one can help me for this regards.
Ali
ML is not for the faint of heart ...
Those reading the first post in threads have a slightly higher chance to prevail!
Dear Walter Schulz,
Thank you for your reply appreciated. Dear my Canon 5D Mark iii came with firmware 123.
so i have format one sd card from camera and should i copy all the files and folder from Naight builds and then run the setup some thing like that. sorry for inconvenience.
Good evening everyone,
I know its been a while since I've posted on here... I have a question... My 5D3 has firmware 1.3.3 on it... Do you guys plan on doing an ML upgrade for this firmware? I would truly appreciate it...
Thx in advance,
Jerry
Downgrade to 1.2.3 or 1.1.3.
Got one of both. The ML/113 is so smooth and glitchless to work with. The 123 is almost exactly the same, but...
When updating firmware to 123 Canon more or less redesigned some of the internals in the 5D3 to allow for direct HDMI, correct an AFMA issue and a lot of other stuff. So when ML was updated to 123, some of the functions had to be changed, not a lot and thankfully not the most important. I use both 113 and 123 every day. 5D3 is a cam. ML makes it my friend.
If you don't need direct HDMI or very precise AFMA, install the 113, or else the 123 firmware with EOS Utility - you may get the firmware here:
http://pel.hu/down/eos5d3-v113-win.zip
http://pel.hu/down/eos5d3-v123-win.zip
Read about the different firmwares and ML's here:
http://www.magiclantern.fm/forum/index.php?topic=14704.0
http://www.magiclantern.fm/forum/index.php?topic=11017.0
Just upgraded to 1.2.3 with December 21, 2015 build as part of experimenting with external monitoring. I quickly realized that as long as i don't need to record "clean HDMI output" but just see everything on big screen, there is no difference. My hope was to get ML screen on 11' in Full HD with 1.2.3. :) Record time slightly less - let's say, 13 sec average versus 16 sec non crop Full HD 30 FPS. And Level indicator is not working!!! Downgrading again :(
When doing regular videos (no ML) with my 5DIII I have been told to set the shutter at twice the frame rate. So for 30 FPS I would set the shutter to 1/60.
My question is -- Now that I have ML do I need to or should keep doing this? I tried other settings and it doesn't seem to have any impact.
I would like the freedom to set shutter faster so that I can open the lens more without the need for a ND filter. At a shutter speed of 1/50 (for 24 fps) and in shutter priority mode, the camera set the aperture to f11. I shot some video. I then changed to aperture priority mode and set the aperture to f5.6, which is more so where I wanted it. I recall the shutter going to 1/320 or so. I shot more video. It didn't seem to make a difference in the final product, and the final video was properly exposed.
I would love to hear comments on this. Thanks.
With a faster the shutter speed you capture less of the motion. The result is less motion blur. During playback it might not be too noticeable. It depends on the action in the shot. If there are quick motions of subjects and you are shooting at 1/240 or faster it could give you a jittery look. Even at 1/120 it can sometimes change the feel. Some filmmakers use a faster shutter for specific effect, but the reason 1/48 or 1/60 has become the norm is because of the natural feeling the motion has to the eye. There are no rules, but just be aware of the effect it gives in the context of what you're trying to achieve.
I like that you try a more "filmic" look with 24fps and a 1/50s shutter (eq. just about 180 degrees shutter rotation "from the good old celluloid days"...). Higher shutter speeds do like in stills: freeze movement - in movies movements become somewhat staggering, which can be useful on rare occasions - see Saving Private Ryan.
With very low ISO you may be able to avoid ND's, but on the other hand: Once you get used to your ND it becomes a friend, and those apertures below 4 are just wonderful for intimacy and drama; big landscapes and wide angle work aren't so critical with higher apertures. Looking forward to see the results.
See Po Chan's / Shane Hurlbut's Canon 5DII iconic short movie The Last Three Minutes, one of the movies that got Canon started with DSLR video in earnest; https://vimeo.com/10570139
Thanks for everything axelcine I truly appreciate the info...
I have been using ML successfully on a 5D2 for some time and have just upgraded to the 5D3. This comes with the V. 1.3.3 firmware and the Canon firmware 'upgrade' notes state the following (pasted from their website):
- 'Once the EOS 5D Mark III camera is updated to Version 1.3.3 (or later), it cannot be restored to a previous firmware Version (Version 1.0.7 through 1.2.3). ' (My italics).
In order to add ML I know that I will however need to do just that. Do I therefore ignore the Canon statement and just proceed with the V. 1.2.3 downgrade anyway? Of course, technically I have not upgraded to 1.3.3 in the first place, as it is the original firmware as supplied with the body.
Sorry if I am being a nuisance - I don't want to cause unnecessary problems with my new acquisition, but would like to continue to have the invaluable extras that I enjoyed on the 5D2. Many thanks for the excellent work of all your software wizards.
Tom
The part about "cannot downgrade after this firmware is installed" (wording may differ) is not new but still incorrect.
Only in 5D3 1.3.3 Canon made an effort to disable downgrading. In-camera downgrade is actually blocked and you have to use EOS Utility v2.x to downgrade from 1.3.3.
Thank you very much for your help.
Tom
i have a 5dmk3 running on fw 1.2.3. i installed ml nightly build 2015dec205d3123.
everything seems successful and i was able to bring up the ml menu by pressing the delete button. however, i can't seem to find the function for afma/dottune.
anyone can point me to the right direction? thanks!
Sounds like you didn't turn on their respective modules yet (check under Modules section within ML menu) and once you do don't forget to restart your 5D3.
FWIW I was able to downgrade to 1.2.3 on my new 5DIII using canon utility 3.x, I didn't have to use 2.x as stated above.
thanks DeafEyeJedi. that solved it!
Anyone knows if there's gonna be a nightly built release for the 5D mark3 firmware 1.3.3 coming out anytime soon ?
I sent my 5D to canon for service and they updated the firmware on me so i can't run ML no more : (
Downgrade. EOS Utility v2.x needed.
Pretty much every clip I shoot with ML has some sort of dead frame in it like you see above. Am I doing something wrong? I am useing magiclantern-Nightly.2015Dec20.5D3123.zip
Try latest nightly based upon fw 1.1.3 and downgrade before to check if that happens over there too.
Need some help with Motion Detection.
I am running Nightly.2015Dec20.5D3123 and unable to get my camera to fire in Frame Difference mode of Motion Detection feature. The other 2 options of Exposure Difference and Steady Hands are working as expected. The left hand top corner constantly shows Motion level: 0. I tried all sensitivity levels and detection area options, but all in vein. Can somebody please help? Intended use is photographing water drops.
Regards,
Guru
Already answered in another thread:
Quote
- motion detection in "frame difference" mode does not work on 1.2.3 or later
Thanks for clarifying. Will downgrade to 1.1.3 and try my luck with it.
Video on how to Install / Uninstall Magic lantern on 5D mark III 2016 + download link : https://www.youtube.com/watch?v=smQ7BwKEO60
Hey guys, I have a quick question for ML.
Do you think is it possible to have an "AUTOMATIC " level correction function in ML?
I know ML already has a green level meter function in LiveView mode and Canon has it's own level meter in viewfinder mode.
What I mean is, with the AUTOMATIC level correction, you don't need to correct to rotate pictures when taking pictures at first.
With a G sensor, canon DSLR can rotate portrait image automatically.
Moreover, with the function, you can always take a picture not askew. (You can ON/OFF on the menu, for sure.)
I think this function would be possible fixing firmware, what do you guy's think on this?
http://www.magiclantern.fm/forum/index.php?topic=15426
Dear a1ex, thank you for the info.
But I don't mean a post-processing after taking photos, I mean a correcting level processing from the beginning when taking pictures.
Even though I try to take a skewed picture, it corrects automatically.
Plus 1) if it's possible, it would be better to process without rotating and cropping.
Plus 2) The reason why I ask you for this is I saw a small device attachment to 6mm DV camcorder with the same function. (REAL-TIME auto level correction device.)
Having sorta similar problem as previous poster with latest build (magiclantern-Nightly.2015Dec20.5D3123.zip). Getting dead/distorted frames within my clips using this version. Will hopefully try 1.1.3 version at some point, but need Canon's 1.2.3 firmware for my work.
In the meantime, any thoughts or ideas on what could be causing it or how to fix it, would be appreciated!
For people out there getting corrupt frames. The earliest 1.2.3 build I can find that doesn't produce corrupt frames is August 7th 2014.
In this build, debug logging had not yet been implemented in mlv_rec. Since, then corrupt frames are fairly rife in my experience, especially when shooting 50/60p.
The latest versions of 1.1.3 are clean as debug logging was disabled again since April 10th 2016.
I've done loads of testing to indicate debug logging is the primary cause of this issue.
I'm wondering if we can see a new 1.2.3 build with debug logging disabled in mlv_rec?
Thanks beauchampy! I actually just upgraded from the "magiclantern-Nightly.2014Aug07.5D3123" build" directly to the latest one and never noticed the problem before.
Guess I'll just go back to that one. Would be great to have the debug logging disabled in the newest one also, but until then I guess I'll stick with 2014Aug07 or try 1.1.3 at some point.
Hey guys, I have a question:
I want to use the dual audio channel recording, but i cant find in the audio menu. only have two things:
- speaker volume
- beep, test tones
What should I do? (5dm3)
thanks!
This is almost certainly not the right topic but will there be a ML release for the 1.3.3 5d iii firmware update?
Will the ML release for 1.2.3 work on the 1.3.3 firmware?
Thanks.
http://wiki.magiclantern.fm/faq#when_will_you_implement_xyz
You should also try and become friends with the search function, because you're not the first person to have asked. ;)
hi. ı am using an april 02 2016 build for 1.2.3 since april.
I shot 2 short films in raw with this build and it works flawlessly. but the build is not listed anymore.
why is that? am I taking a risk by using that?
thanks.
I'm missing almost all features in Audio Tab. Only Speaker Volume and Beep, test tone is left.
Is it normal or I'm doing something wrong?
Quote from: dalifen on July 06, 2016, 03:48:32 AM
Is it normal or I'm doing something wrong?
https://builds.magiclantern.fm/#/features
Hi Audionut,
thanx for reply, but unfortunately list of features is not the right answer. All the audio features suppose to be there for 5D3 (as one can see in list of features), but they does not show up. I'm mainly interested in Input source option.
BTW, modules are another problemfor me. Neither 5D3 nor 5D2 I have on the desk here is able to load mlv_snd (sound module). Both results in err while loading it.
Quote from: dalifen on July 06, 2016, 09:32:58 AM
All the audio features suppose to be there for 5D3 (as one can see in list of features), but they does not show up.
Sorry?
Quote from: dalifen on July 06, 2016, 09:32:58 AM
BTW, modules are another problemfor me. Neither 5D3 nor 5D2 I have on the desk here is able to load mlv_snd (sound module). Both results in err while loading it.
MLV_SND.mo depends on MLV_REC.mo
Man, yes, You right!
But I can see the audio features present right on the pic of 5D3 at the ML homepage???
http://www.magiclantern.fm/index.html
But loading mlv_snd, after mlv_rec was the solution, thanx for that.
Quote from: dalifen on July 06, 2016, 10:06:14 AM
But I can see the audio features present right on the pic of 5D3 at the ML homepage???
http://www.magiclantern.fm/index.html
Feature list is generated by robot parsing ML source code for each cam supported.
Homepage is not.
I see that, thanks again Walter,
so shall I realise it, the audio features were included in older builds of ML for 5D3, but not the present build?
Or maybe the ML for 1.1.3, but not the version for 1.2.3 firmware?
5D3 and all other DIGIC 5 cams never had the full set of ML audio features implemented for DIGIC 4 (50D excluded).
Well yes, it's pity for me, I'd appreciated it a lot, but unlike the homepage picture, perfectly clear info from you. Thanx.
Btw. I've got another question, should be in 5D2 forum correctly, but I believe You know the answer. When monitoring sound during live view on 5D2 I only hear left channel, is it a problem of my very camera, or it's normal and I mis a cable with some special wiring? (rca to phone jack adapter or a sesscom cable - don't have clu what is it)
Sorry, please switch to 5D2 thread after consulting search function.
OK, I see.
Anyway thanks to everybody behind this sweet piece of software, I appreciate it a lot.
Synced the source code to main builds, so a new nightly should appear soon.
Please note the build is untested, so you should probably wait for feedback from early testers before upgrading.
Looking forward to it. Thanks @a1ex!
Quote from: a1ex on August 23, 2016, 10:38:01 PM
Please note the build is untested, so you should probably wait for feedback from early testers before upgrading.
Thanks a1ex. So far so good with this build. ML menus all work fine, and I haven't noticed any problems with what I've tried (briefly) so far: dual-ISO, auto ETTR, advanced bracketing, silent pictures, various global draw features. I haven't tried any video features.
Just wondering in the newest 1.2.3 nightly (8-23-2016) if debug logging is disabled in mlv_rec again?
Reason I ask, is in reference to reply #1386 (http://www.magiclantern.fm/forum/index.php?topic=11017.msg167362#msg167362), it seems that may have been the problem for corrupt frames.
https://builds.magiclantern.fm/jenkins/job/5D3.123/45/
See #304
BIG thanks to a1ex and everyone else who made this new 123 build happen :)
Clean HDMI is really important to some of us, so this is gratefully received!
Dear All,
Does Magic Lantern offer a possibility to record voice tags? I tried to find such a functionality but was not successful.
Thx in advance,
WGT
http://www.magiclantern.fm/forum/index.php?topic=16377.0
Many thanks to a1ex and everyone who contributed on this :)
And now the 5D Mark IV. What would ML do with 4K - non-cropped video RAW ;
there is already 5d4 discussion in the general chat...as for the new build many thanks...recorded 1T at 1080/ 24&25 fps and everything looks good. Ill do my tests at higher fps and cropped modes later
Quote from: unfilmde on August 26, 2016, 11:06:06 PM
And now the 5D Mark IV. What would ML do with 4K - non-cropped video RAW ;
I think Canon is giving Jpegs. And we need RAW, I hope Team ML will stand and deliver again to the challenge.
Quotethere is already 5d4 discussion in the general chat...as for the new build many thanks...recorded 1T at 1080/ 24&25 fps and everything looks good. Ill do my tests at higher fps and cropped modes later
Direct link for the 5Dmk4 discussions, please? I can't find it.
http://magiclantern.fm/forum/index.php?topic=17695.0
With the Nightly.2016Aug24.5D3123 build, rec.led.off = 1 doesn't work any more?
Adding this line to magic.cfg doesn't work, red LED still blinks when recording.
Anything I'm missing?
whoops just saw #48 in https://builds.magiclantern.fm/jenkins/job/5D3.123/45/
It says old hackish implementation, doesn't seem to work anyway. Well, it worked fine for me on the previous 2015Dec20.5D3123 build anyway.. what gives?
Last time I tried it, I could barely notice any difference.
If there is still interest in this feature, I can look into it again.
Quote from: a1ex on September 14, 2016, 08:25:24 AM
Last time I tried it, I could barely notice any difference.
If there is still interest in this feature, I can look into it again.
Yup it worked flawlessly for me, both normal h.264 and raw/mlv won't have the red LED blinkin'. So yea,
rec.led.off is worth a look i guess.
Quote from: a1ex on September 14, 2016, 08:25:24 AM
If there is still interest in this feature, I can look into it again.
+1
With Nightly.2016Oct09.5D3123 build, rec.led.off is still disabled?
Anyone can confirm?
not sure if this is the right topic, but here we go:
specs:
5d3 1.2.3 With Nightly.2016Oct09.5D3123
FeelWorld 760 (1080p native 7 inch). I tested the monitor and it can display 1080p from my laptop. According the specs it can display @ 50/60//24 fps
camera settings:
I set the camera settings to mirror HDMI, PAL, 1920@24fps video
magic lantern settings to default.
But even what I try it always seems to output 1080i (50/60hz) over hdmi instead of 1080p @ 24
tried:
I tried ntsc, 25 fps, 24fps hdmi output as options, but it's not helping.
is it even possible or am I missing something?
@savale
I think thats normal, when I use the atomos ninja blade I can select in the ninja menu if I want to do pulldown to 25p when the camera outputs 1080i.
By the way if you only use it for monitoring 1080i should be fine, the camera will record to 24/25p internally.
Thank you Lars, recording is fine, but for focus pulling it's a bit easier when having 1080p instead of 1080i.
I finally found a solution for the monitor: When I put it to oversan full it seems to understand the 1080p signal inside the 50hz signal. (I set the camera to output 24p)
Hey I've got the mark III. I Recently ordered the ATOMOS Shogun Inferno for my future RED Scarlet-W. for now I wanted to know if anyone knows if magic lantern works with atomos monitors. I don't necessarily want to record on to the Inferno just use it as a monitor but still get RAW plus I don't think it's even possible to record raw through hdmi.
I have purchased my 5D Mark iii couple of days back.
I'm trying to downgrade to Firmware 1.23 and I'm using Mac osX 10.11
I'm not able to find Firmware 1.23 version for Mac osX 10.11
Could anyone please help me?
Please sent a link for osX 10.11, really appreciate the help.
I have also noticed a change in canon Utility Software...
Now the firmware update is under
Camera Settings > Firmware update
Please confirm if it is the correct way to update than going into remote shooting
in fact, I don't see firmware in that section
Thanks,
Jowish Simon
Quote from: jowish77 on December 04, 2016, 12:07:50 AM
I have purchased my 5D Mark iii couple of days back.
I'm trying to downgrade to Firmware 1.23 and I'm using Mac osX 10.11
I'm not able to find Firmware 1.23 version for Mac osX 10.11
Could anyone please help me?
Please sent a link for osX 10.11, really appreciate the help.
I have also noticed a change in canon Utility Software...
Now the firmware update is under
Camera Settings > Firmware update
Please confirm if it is the correct way to update than going into remote shooting
in fact, I don't see firmware in that section
Thanks,
Jowish Simon
Just FYI it's the same as the Windows version. They both come with 5D300123.FIR and you just need to use EOS Utility to downgrade.
Hi Everyone,
Oops, I have a new Canon 5D MKIII on the way and didn't know about all these firmware issues with the Canon 1.3.3 firmware. Having purchaed a T2i 550D years ago, I've been looking forward to the opportunity to shoot RAW (even if the workflow is somewhat tedious), but have considered returning it due to the firmware issues. From reading some threads on this topic, it seems obvious that I need to downgrade to an earlier firmware (either 1.1.3 or 1.2.3). My questions are therefore:
Where can I find a very discriptive tutorial on how to downgrade to 1.1.3 or 1.2.3 using Windows 10.
I want to have "Clean HDMI Out" and "Dual Monitor Support" so which version should i downgrade to?
After downgrading to earlier camera firmware, I understand I need to install basic ML, then set up for RAW recording, correct?
This being the case, how do you also set the 5DMKIII up for RAW after basic ML is loaded?
Is ML RAW set up using settings within basic ML firmware, or does RAW require another download?
Thanks guys.
Use EOS Utility 2.x to downgrade. If unable to locate this utility:
http://pel.hu/down/solution-disk29.1a.dmg.zip
After installing ML you have to go to Modules tab and activate MLV_REC.mo
Walter.
I assume version 1.2.3 is the best one to use if I wish to use "clean HDMI out" and to have dual monitors, correct?
Is v 1.2.3 also the best version for shooting RAW, or does it matter?
If so, where can I download the Canon 5D MK III 1.2.3 Firmware?
Thanks again
If you need to AF at f/8 while shooting stills, then stay at 1.2.3 else go back to 1.1.3. I am at 1.2.3 for the AF at f/8.
Quote from: IndyP on December 09, 2016, 01:07:00 AM
I assume version 1.2.3 is the best one to use if I wish to use "clean HDMI out" and to have dual monitors, correct?
Is v 1.2.3 also the best version for shooting RAW, or does it matter?
http://www.magiclantern.fm/forum/index.php?topic=14704.0
Quote from: IndyP on December 09, 2016, 01:07:00 AM
If so, where can I download the Canon 5D MK III 1.2.3 Firmware?
Read first post of this thread.
Sorry for my newbie question but this my problem:
I have installed ML on my 5D Mark III 1.2.3 (magiclantern-Nightly) to solve my hissing audio problem with an external mike (RODE)
Specifically I was looking for a way to disactivate the AGC filter... (Auto Gain Filter)
Couldn't find an option on the menu and I tried to activate the MLV_SND.MO module, but this is the answer I get in the console
tic: error: undefined Symbol 'mlv_record_get_free_slot'
plus more lines like this one
SCREENSHOT
https://www.dropbox.com/sh/571y1gbgit8fv6n/AACsaXcJG-ArIffi2zlHi1Dna?dl=0 (https://www.dropbox.com/sh/571y1gbgit8fv6n/AACsaXcJG-ArIffi2zlHi1Dna?dl=0)
Any help highly appreciated!!
thanks
a
Quote from: avator on December 09, 2016, 07:44:31 PM
Sorry for my newbie question but this my problem:
I have installed ML on my 5D Mark III 1.2.3 (magiclantern-Nightly) to solve my hissing audio problem with an external mike (RODE)
Specifically I was looking for a way to disactivate the AGC filter... (Auto Gain Filter)
Couldn't find an option on the menu and I tried to activate the MLV_SND.MO module, but this is the answer I get in the console
tic: error: undefined Symbol 'mlv_record_get_free_slot'
plus more lines like this one
SCREENSHOT
https://www.dropbox.com/sh/571y1gbgit8fv6n/AACsaXcJG-ArIffi2zlHi1Dna?dl=0 (https://www.dropbox.com/sh/571y1gbgit8fv6n/AACsaXcJG-ArIffi2zlHi1Dna?dl=0)
Any help highly appreciated!!
thanks
a
You deactivate the auto gain in the canon menu, not the ML menu.
Why is 1.1.3 recommended? When 1.2.3 has more posts in this thread then for 1.1.3? I just got 5d mark iii and I'm wondering which one I should go with.
Quote from: king718 on December 10, 2016, 06:22:58 AM
Why is 1.1.3 recommended?
You should read first post in 1.1.3. and make up your mind about which version you want to use for your projects.
I've just received my 5D MK III and am ready to downgrade to 1.2.3. Does anyone know where I can get the correct EOS Utility version for Windows 10 to perform the downgrade? I'm told that the EOS Utility version 2x is what I need, which means the most recent version offered by Canon with the 5D MKIII will not work (though I haven't tried it).
Thanks
"EOS Digital Solution Disk Software 29.1A" for Windows or OS X available via Canon Support USA web site.
Thanks Walter, I saw that but was looking for a 2x. I guess that should do it.
Update: I installed EOS Utility Disk 29-1a for Windows, and downloaded the Canon 5D MKIII Firmware v1.2.3 file from the Magic Lantern
Downloads page. Using the above utility, all went well and I downgraded from 1.3.3 to v1.2.3.
OK, I installed Magic Lantern without any problems, and now I'm ready to activate a RAW_REC.MO or MLV_REC.MO module. My question now is; what are the main differences between each of these modules for shooting RAW?
Apparently some individuals were experiencing problems with external monitoring, i.e. (dropped frames and monitor freezing after a minute or so) when using mlv_rec.mo and advised to go with raw_rec.mo instead, as it was less problematic. These problems apparently went away after they began using a faster card.
In any case, (not sure if it's relevant), but I will also be using an external monitor, so which module would it be best to go with?
Oops, this is a continuation of my original question, but I'm now talking about RAW. Perhaps I should now move my discussion to the RAW thread?
@IndyP
You should really looking for that answers on google.
It's one of the most common questions.
hope to see a new nightly for 1.2.3 soon..
@IndyP
"If you don't have anything good to say, don't say anything."
Google it.
Hello everyone,
Wanted to share my latest findings with the latest 5d Mk3 nightly build for 123. I recorded ML RAW and ML Sound and sent the signal to my Atomos Ninja Blade via Pro Res HQ. I didn't get a signal for sound in my Ninja Blade via HDMI, anyone know why?
https://youtu.be/e5ZDA6uJ5bo
OS 10.10.5
CF card Lexas 1066x 64GB
MLFVS to convert ML files to cDNG (.45 seconds equals about 4 Gigs. WOW!)
Imported cDNG to Resolve
Exported Pro Res 4444
Imported ProRes 4444 and Ninja Blade ProRes HQ into Premiere Pro CC.
Export H.264 - Vimeo 1080p preset
Thanks again to the Magic Lantern team for their work. Where is the donate button through Paypal? I only see the one for BitCoin. What if you can't sign up for Bitcoin?
I'll be doing some more testing, trying to find out how to send ML Sound into Ninja Blade. Any suggestions?
@CineRAW
No sound because canon does not output sound on the 5D Mark 3 over HDMI
@lars
thanks for the info on sound over HDMI. Next i'll try running the headphone jack output into the ninja blade sound input and see what I get.
the headphone to atomos will work, just test how many frames offset you need to add in the atomos. when you have the correct value for the offset the sound will be sync.
Quote from: Lars Steenhoff on December 20, 2016, 10:46:13 PM
the headphone to atomos will work, just test how many frames offset you need to add in the atomos. when you have the correct value for the offset the sound will be sync.
I use 5 frames on mine.
It seems that there is a large section of the ML community that is hungry to get 5D.123 updated with the latest features. Every time I put up a new 123 test build the downloads exceed that of the 113 builds. I may be wrong but my opinion is if you want to help Magic Lantern move forward and you already have a 5D3 the best place to start isn't with getting a new camera that hasn't been ported yet and bugging developers when it will happen but by getting your camera working smoothly with 123.
I don't have a 5D3 but if I did I'd be all over getting it working with 123 or even trying to update it to the latest (134) firmware.
Why? Well one reason would be because there is some exciting work being discussed on the Programmatic focus control and absolute/relative focus position (http://www.magiclantern.fm/forum/index.php?topic=4997.0) topic and it seems that some of the issues that are being encountered might have been fixed by Canon.
Driver / Software Details:
QuoteChanges in Version 1.3.3:
1. Improves the AF controllability when shooting in Live View mode with a wide-angle lens (fixed focal length or zoom).
If you have the skills, porting 123 to 134 probably isn't as big of a jump as porting a new camera. The porting of new cameras will happen in time by developers who are happier working on the hard stuff than the little things like searching for stubs on a firmware update.
@dfort
I'm with you.
As you know I'm keen to help, but I'm not up and running in 'compiling mode' yet.
Having said that, with a 5D3 I'm keen to support user testing...and of course Lua scripting developments :)
Cheers
Garry
Just merged 5D3 1.2.3 in unified, along with 1.1.3.
That means, from now on, they will both follow the regular nightly builds and also the experimental builds just like all other platforms, without requiring special attention.
:)
Thank you
Thanks so much for making this happen @a1ex!
wohoooo! I love it.. full support for 5D3123..
Thanks my man! :)
A1ex - I commented on this in the crop branch, but allow me to say it again here: What an achievement. From what you guys told me some time ago, the technical challenge was almost overwhelming, but you masterminded it. Thanks, A1ex and your staff of competent and enthusiastic testers, developers and programmers. You're taking engineering to a new level.
Amazing news, thank you very much! :)
I just got 5d mark 111 and installed magic lantern. I also have a scandisk CP 128 in the camera but the recording keeps shutting of after every 14 secs or so. I made sure to format the card as ExFAT. Could it be a setting I am missing somewhere?
Modules tab -> Load Bench.mo
Restart cam
Debug tab -> Benchmarks -> Card Benchmarks -> Quick R/W benchmark (1 min)
After completion you get a PPM file on card's root directory. Convert file to JPEG or PNG and use a free filehoster to share it here.
There is no ppm file in the root. The file I see in the 100EOS5D mlv_rec.tmp. By the way how do i get filehoster and how do I use it to upload stuff to here
I'll jump in here, as I've never used a free filehosting approach.
Can someone recommend a stable and 'safe' one?
@bineyboy: Check cam's root.
Run benchmark in cam.
Check cam's root again after benchmark terminates.
Process file created after benchmark run and link it here.
No use to try it with mlv_rec.tmp.
Thank you so much Walter. Please be patient with me. Very new at all this. Actually first time with even DSLR. How do I check Cam's root? and how do I process it. I really appreciate your help. If it won't be too much trouble for you I can give you my number so or I can call you so you can help me over the phone.
Please take into consideration ML was and is designed by and for people missing some features in Canon DSLRs.
I don't know which path (with photo gear) you took before getting a 5D3. Even people located on the geek side of photography may become overwhelmed by the plethora of new things to learn about the cam they thought to know so well. I cannot recommend ML for beginners. I strongly suggest to get to know the cam first without it.
If you insist using ML anyway:
Be prepared to use search engines a lot: "Root of card" can be googled.
PPM = Portable Pixel Map = A format to store pixel data aka pictures. More often used file formats for pics (at least on the internet) are PNG, JPG. Some image viewers are able to convert. So is Photoshop. Which programs will do for the OS your PC is running can be googled, too.
Thank you for your advice. I am determined to learn so I will google and follow your instructions. Performing the module a second time right now to see if it creates a file at the root directory of the card. If it does I will upload the file here.
I completed the process and I just saw that the ppm File you are talking about is being put on the SD card not the CF card and I was constantly checking the CF card.
Walter here is a link to the file. Let me know if you are able to see it.
https://www.dropbox.com/scl/fi/cwk4d5fqpvs2w5o0dq9j3/BENCH3.jpg?oref=e&r=AAQizIbpX0kxocibYYoqk2C13i3LUJjzQTim9Yae_Ykel-osWYSN3de2M_xoWcRaPMTHStCttnU3WmKgbC2_2wsWN9nrsQpehz2w-i2JEKUBLX17EhsnJIMNk5-t9H-czKjs-X-4NB_Uamp-Y-DYxVh5c8iA4AAZ6_TaVqbTpsJoOGE03c-ie9c0u-jP_UWDvx4&sm=1
Nope, wants me to login to dropbox. Hoster like picload, imgur would be easier to access by link.
But take a look at the numbers you got for benchmark first. If they are all (without exception) well below 25 MByte/s you benchmarked your SD-card instead. I can't tell if 5D3 is able to run benchmark for CF-card if run from SD-card. If unable: Copy nightly build contents to card and run installation without SD-card once again. Then run benchmark from CF-card.
Walter, I finally was able to use pic load to upload the image. Here is the link. https://pl.vc/tkpha OR https://picload.org/image/rodpgcrr/bench4.jpg Let me know what you think
Looks like a Sandisk Extreme 120 MByte/s card. Write speeds for this card will not reach 70 MByte/s.
Adjust bandwidth demand for chosen resolution/frame rate (visible in ML menu) to about 65 MByte/s (or less) or use a faster card.
OK will do and let you know
In the mean time what will you recommend as a faster card.
Do you think a 128GB scandisk extreme pro speed up to 160m/s (1067X), UDMA 7 enabled, 65 is a good one. It saids 4k on it. Can I still use it to record 1080p?
Yes the sansdik 128 (160 mb)is good, im using them without any broblems for 1080 raw
Woah, thank you to all that made this happen!
Anyway, With Nightly.2017Jan13.5D3123 build, rec.led.off is still disabled? How can i manually enable this?
Hi all, after using ML on a 60D, I got myself a 5D3 and am interesting using ML, obviously its always good to get the unit in the latest software and unless I am missing something the latest firmware on canons site is 1.3.4.
I read though a bunch of posts here which are 'currently' quoting older versions, is it better to leave the camera on an older firmware to use current ML versions or, am I ok to upgrade to 1.3.4 first then use ML?
Version 1.3.4 is not currently supported by Magic Lantern so if you want to enjoy Magic lantern, use 1.2.3 firmware..
I download and installed the last beta night , for 5d3 (fw 1.2.3)
magiclantern-Nightly.2017Jan27.5D3123
but there are no depth bit function , to test here ? no builds for fw 1.2.3 ?
Quote from: jimiz on February 02, 2017, 12:31:57 PM
I download and installed the last beta night , for 5d3 (fw 1.2.3)
magiclantern-Nightly.2017Jan27.5D3123
Nightly Builds are not Beta!
Quote from: jimiz on February 02, 2017, 12:31:57 PM
but there are no depth bit function , to test here ? no builds for fw 1.2.3 ?
There is an experimental build for 1.1.3 -> Top of page -> Downloads -> Experimental -> 10/12-bit RAW video
Crop mode recording for 5D3.123 in the Experimentals download page (https://builds.magiclantern.fm/experiments.html) includes 10/12-bit raw recording.
thanks Walter.
little confusion.....
So You confirm that for 5d3 fw 1.2.3 there are not any beta/experim. with Depth bit option, but only for fw 1.1.3 ?! right ?
Did you look at my post?
Sent from my iPhone using Tapatalk
;) sorry...I'v read now...and I go to try ! THX.
I tested (1920x1080 25p) 10, 12, 14 bit
i try to convert the MLV with raw2dng MLV Mystic and anothers but only the 14 bit work, the anothers not open or are incomprensibles DNG.
there are a special software for convert the 10 and 12 bit MLV ?!
Mlv_dump
Raw2cdng
Cr2hdr.app
Mlvfs
Raw2cdng last version 1.7.9 seem to work now...;)
I have a the firsts frames black on any clip but the rest of frames and clip seem good.
1920 25p 10bit - 61,7MB/s
1920 25p 12bit - 74,1MB/s
1920 25p 14bit - 86,4MB/s
I'm running the latest experimental build 10bit_12bit. (Feb_11)
Somehow I'm getting the "busy" status after recording raw with mlv_rec. I thought that was fixed long ago, at least this topic states so http://www.magiclantern.fm/forum/index.php?topic=13706.0
I've just got a 5D3 again, so playing with it - has anyone got the same issue?
P.S.
I've shot some clips today with mlv_rec (1920*1080@24fps), all the videos turned out with the green cast to them (wrong black level), is there a way to fix them (other than tuning the black levels in post?)
I have a question. I spent an hour looking for the answer on these forums, but haven't been able to find one.
Note: This may be an ML issue, or possibly just a Canon issue. Or maybe even Atomos? I'm not sure.
I recently went to firmware f1.2.3 and everything has been good so far, except for one thing. I have a monitor (in my case, an Atomos Ninja Blade -- used only as a monitor) plugged into the camera via HDMI. Mirroring is off.
When I turn the camera and monitor on, I get a blank screen on the monitor. Unplugging the monitor brings up a prompt on the camera's LCD to hit "Start/Stop" to enter recording mode. ML does not seem to load. Hitting that button does nothing and I have to restart the camera.
Whether I turn the monitor on first, then the camera, or if I do it the other way around, I get the same result. The only workaround has been to let the shutter go up and ML to load, and then plug in my camera. It's kind of a nuisance, especially since I plan to run both camera and monitor off of the same battery.
Any ideas?
So with the nightly build of -03-06-2017 for 5D MKIII RAW shooting has been removed and it's just RAW MLV?
MLV_Lite, not MLV.
http://www.magiclantern.fm/forum/index.php?topic=16650.msg179879#msg179879
and first message. According to a1ex performance should not drop significantly (compared to native/old raw_rec.mo).
I gave the Lite a try. Interesting with 2017-03-06, if you don't turn RAW-MLV on RAW Video and Magic Lantern won't load and give Err codes.
Quote from: unfilmde on March 08, 2017, 07:58:01 PM
Interesting with 2017-03-06, if you don't turn RAW-MLV on RAW Video and Magic Lantern won't load and give Err codes.
Sorry, I have trouble understanding what you did and what happened (not native English speaker).
This may help too: http://www.chiark.greenend.org.uk/~sgtatham/bugs.html
a1ex, here's what I did. I deactivated RAW.REC in the modules setting and power cycled the 5D. I activated RAW.MLV in modules settings and shot some footage and power cycled the 5D. I deactivated RAW.MLV and activated RAW.REC again and power cycled the 5D. I got errors Err codes, modules won't load. I power cycled the 5D. I activated RAW.Rec and RAW.MLV and power cycled the 5D. I then turned off RAW.MLV without deactivating it and I can shoot RAW.REC (MLV-Lite).
There's nothing in ML called "RAW.REC" or "RAW.MLV". It sounds like you might be talking about modules. You are probably getting the error because you left one of the modules that depends on mlv_rec.mo turned on (probably mlv_snd.mo).
We could clear this up if you would be more precise. Don't just say "I got Err code", say what they were or post a screenshot. Don't make up you own names for modules, use the actual names. State every module you have enabled/disabled, not just the ones you think are important.
Hello, do you know if I can run Magic lantern on CF card and record to and SD card simultaneously? I dont want to download ML to all my separate sd cards and would rather just download it once. I do not plan on recording raw at the moment and simply want ML for some of its other features. Do you know how much space ML usually occupies on a CF card?
I plan on using it on a Canon 5d Mark 3.
Thank You...
Quote from: vancitybud on March 20, 2017, 07:13:57 PM
Hello, do you know if I can run Magic lantern on CF card and record to and SD card simultaneously? I dont want to download ML to all my separate sd cards and would rather just download it once. I do not plan on recording raw at the moment and simply want ML for some of its other features. Do you know how much space ML usually occupies on a CF card?
I plan on using it on a Canon 5d Mark 3.
Thank You...
ML will just occupy some MBs on the card, you do not need to worry about that; and it only has to be installed in the card that the camera boots from, not on both of them.
Hello and thanks for this amazing software!
Is there any introduction how to turn on 50fps in 1920px? I managed to install ML on my card and the options are there, however, even when I turn it ON it is still in 25fps...
Is there any other option I need to turn on perhaps...Please help if you know how to tweak this :D Thanks a lot.
To use 1080 with 50fps you need to be using the latest experimental firmware. Activate mlv_lite and crop_rec module. Set crop rec to 1080 50 then set the resolution in mlv lite.
I am using magiclantern-Nightly.2017Mar30.5D3123. My previous version would have been 1-1.5 years old.
I use it for timelapse and it always works great. I just updated to the new version and did 15 timelapses on a job. About half of them go out of focus from the 3rd photo onwards. Looks like it goes to the minimal focus of the lens. It happened on 2 different lens both switched to manual focus. I thought it might have been because of the half-shutter press used to activate the timelapse but I've always done it that way and never had trouble.
Anyone else come across this?
Did anyone know is this a feature or a bug?.
When the "Zoom on HalfShutter" option is enabled, it also affect the SET button.
Pressing SET button also zooms.
Or maybe I just missed some setting?
Just got a 5d3 and wanting to explore ML. Current firmware is 1.3.4. Is there a stable release for it right now?
Question: how to record sound with this build?
Only with external sound recorder?
If so then how to mix it with footage? Are there any time codes options?
Please share how you guys handle with this.
I'm hoping that we'll get MLV Sound module working with the new experimental builds soon. It'd be very helpful for synching a day's worth of footage (and for back up sound). It sounds like for now they have other priorities.
One possible option for timecode with external sound recording would be the Sound Devices MixPre-3 that was recently announced. It accepts HDMI to get timecode. Not sure if it works with the 5Diii's HDMI output though.
I agree about the sound. In my opinion the lack of sound integration is the most significant short-coming of magic lantern. I record the h264 proxies but they require syncing to the mlvs in post and it is exhausting.
Maybe a funding situation can be organized or something to basically achieve synced sound asap. Then plural eyes can do the rest for external recorders.
Quote from: erikbaldwinson on May 24, 2017, 10:04:43 AM
Maybe a funding situation can be organized
AWGTHTGTTA?
You will most likely kill the project doing so.
Ceterum censeo experimental build downloads esse delendam.
I am having problems updating to fir 123 from 113
I followed canon instructions, but i keep hitting a wall.
I am obviously doing something wrong but i dont know what. Iremove ML from SD card, place fir 123 file on the SD card and insert the card in camera. The camera is completely dead after this, on/off does nothing, photo mode or liveview aswell. Also when inserting the sd card not even a LED blink. Also without any cards in camera, it remains dead. I have to reinstate the apr 29 build for 113 on the sd card and that brings back the camera to life and everything works as before.
I reseted canon and ml settings (lost my PP's :( ) same thing, camera dies.
Any advice on what i am doing wrong?
I have never used 113 ver of ML. I use 123. When I updated from 121 to 123, I uninstalled the 121 version and then installed the 123 version. From your description I am not sure if you uninstalled the 113 version prior to removing the card.
How do i go about uninstalling firmware? Sounds a bit wrong.
I am sure i've read that people just updated from 113 to 123. But removing ML properly from the camera might be my issue, which i am not sure how to perform.
I used to use ML over two years ago, but removed it as it was quite buggy, especially when filming, so I would not dare using it on the job. I know these types of questions are usually frowned upon but just want to check if it is more stable today?
Have been following the thread on and off but not read every message the past two years. Really want to give it a shot again as the features are amazing and just want to see what has happened in the stability department since before.
So stupid, should have read the ML User Guide.
I didn't format the Card before putting the 123 fir file on. That's why it didn't work.
i am new here, is there a ML for 5D3 Firmware 1.3.3?
Quote from: Sundaramkm on July 11, 2017, 12:29:11 PM
i am new here, is there a ML for 5D3 Firmware 1.3.3?
No. You have to downgrade with the EOS Utility to 1.2.3 or 1.1.3.
Quote from: Sundaramkm on July 11, 2017, 12:29:11 PM
i am new here, is there a ML for 5D3 Firmware 1.3.3?
Actually, there is. @chris_overseas did one and it is still available on his bitbucket repository (https://bitbucket.org/chris_miller/ml-5d3-133/branch/5D3-133). I used it as a reference for a 5D3.134 update. Note that these are experimental and have issues. If you can't compile and help debug then it would be best to downgrade your Canon firmware to 123 or 113. You need to use EOS Utility. I wrote a tutorial on how to do it (http://www.magiclantern.fm/forum/index.php?topic=18941.msg179783#msg179783).
HI...actualy last nightly build x 5d3 (123) is of 1 August
Latest Build (2017-08-01 00:12)
any body know IF this version fo ML have inside also the Crop mode recording (crop_rec)
from the last (old) experimental Latest Build (2017-03-21 00:22)??
Why I don't have focus patterns option? I really love to have horizontal control.
(https://postimg.org/image/cggt237c9/)
(https://postimg.org/image/f5bls4ctl/)
(https://postimg.org/image/4jrqg46i1/)
(https://postimg.org/image/8itjcokix/)
(https://postimg.org/image/48aa3cq21/)
Hi Guys,
I am trying to install ML for the first time.
I am on a mac and it won't let me unzip the Autoexec.bin file. It just keeps giving me an new file to unzip
Any suggestions?
Cheers
Hi, when i start to record my cropmark and eveything is disappeared from my canon LCD. Why, can someone help me?
Quote from: Fraserm3 on September 13, 2017, 07:44:12 AM
Hi Guys,
I am trying to install ML for the first time.
I am on a mac and it won't let me unzip the Autoexec.bin file. It just keeps giving me an new file to unzip
Any suggestions?
Cheers
Don't unzip that file. It should live as is at the root of the card.
Hello, I just in installed Magic Lantern for the first time on my 5D Mark III.
Everything's ok, but I can't find the RAW_Rec modules. Any help?
Thank you!!
RAW_REC.mo no longer supported in nightly builds. Replaced by MLV_lite.mo.
See linked threads in Downloads -> Download Nightly Builds -> Features -> Modules
Hello!!
Does anybody knows where i can find the 1.2.3 firmware? this link doesn't work! http://pel.hu/down/eos5d3-v123-win.zip
Looks like Pelican's website is down. I've got several Canon firmware updaters in my Bitbucket downloads page (https://bitbucket.org/daniel_fort/magic-lantern/downloads/) -- look for the one named "5D3 Canon Firmware for Testers.zip"
Help, my HD broke and now I am searching for 5d3 firmware 1.2.3.
Can anybody help me with a link?
Thx to community and unknown friendships.
Archie
Hey Archie -- read the posts just above your post and you'll get your answer.
:) ouu Christmas THX
Just purchased a 5D3, an upgrade from my 60D running ML. I see dforts post about downgrading from 1.3.4 so I can install ML on my 5D3.
I clicked on his tutorial, and the last post from 2/13/17 mentions trying to get a ML version for 1.3.4....before I downgraded, it just makes sense to ask what the progress of that is.
Thanks!
JIM
There's a whole topic dedicated to it:
Canon 5D Mark III / 5D3 / Firmware 1.3.4 (https://www.magiclantern.fm/forum/index.php?topic=18966.0)
Skip to the end and you'll see that just when it seemed like the bugs were ironed out Canon introduced 1.3.5 so it was back to square 1. If you want to try 1.3.4, a test build is on my downloads page (https://bitbucket.org/daniel_fort/magic-lantern/downloads/). This is very experimental and doesn't have a ML-SETUP.FIR which is needed to install ML so you'll have to install ML on 1.1.3 or 1.2.3 before running the Canon firmware updater. In your case you'll have to downgrade, install ML then upgrade back to 1.3.4.
Just a tip--you'll have the best experience with the 5D3.113 crop_rec_4k build.
Thanks for the reply dfort. Just want to thank you and all the others who have the brain power to figure this all out and then share it with the rest of us. It kills me that a camera like the 5DIII doesn't have the basics that I've grown to take for granted on my 60D rocking ML. Having a histogram on the screen while filming and peaking should be standard in any camera that takes video. I'll check out the thread you posted.
JIM
I'm not 100% where to post so I'm hoping someone can help me with this I have been using magic lantern for a couple weeks now and as of recently have been playing with the RAW footage that I see people posting about my only issue Is I am not sure how to make it 4k I see the option but when I go to it says camera cant support this with this mode I have seen tons of people give tutorials on youtube and have followed along and they dont have this issue they also have an option for crop video which I dont see. Thanks for any help?
Enter crop mode by pressing loupe button (5x).
When I turn on/off crop mode, screen FeelWorld F570 is black for 2 seconds (same effect when I press Menu button). But next hdmi resolution is still 1080p without change...
Is it possible reduce downtime?
Probably, but it's not trivial. Best guess: this might work if one can somehow prevent Canon code from turning the display off during video mode changes (or from actually sending the "display off/on" sequences to the HDMI chip).
Starting points:
https://www.magiclantern.fm/forum/index.php?topic=21573
https://a1ex.bitbucket.io/ML/states/5D3-123-alt/sm72.htm
Unable to look into this in the near future, sorry.
What does the green dots and the number indicate? I have a battery grip attached.
Sent from my Pixel 2 XL using Tapatalk
Why does Canon Utility not recognize videos in my MK III when trying to transfer to a computer via USB?
Why does the CF card in the camera not show up in the file menu on my computer when the camera is connected via USB cable?
Are these thing possible to fix? I don´t want to take out the delicate and expensive CF card after every photosession and put it into a cardreader with a possible risk to damage it in the end...
/olof
I use a mac - Yosemite
-----------------------------------------
Thank you Walter :D, 18 MByte/s is slow....
CF-card connectors are specified for 5000 mating cycles. Same number for USB mini connectors.
AFAIK Canon code does support "official" file formats only. You may be forced to rename DNG/MLV if you insist on stressing USB-mini at about 18 MByte/s. Plus stressing battery (limited recharge cycles...).
Quote from: Pimmen on June 02, 2018, 07:39:59 PM
What does the green dots and the number indicate? I have a battery grip attached.
https://davidmilligan.github.io/ml-lua/modules/battery.html#performance (https://davidmilligan.github.io/ml-lua/modules/battery.html#performance)
Performance - Get how many "green dots" (3 for a new battery, less for a used battery)
Quote from: a1ex on March 16, 2014, 03:26:45 PM
What's not:
- no full-screen magic zoom (I never used it anyway, but was nice)
That's the only reason why I have to switch between 1.1.3 and 1.2.3.
How do I set up my mk III to succeed in filming with 48 fps continuos at 1920x1080 without a break (AND what not to set up...) - I tried everything 😟
Please give me a recipe how and where to fill in what in the Magic Lantern menus...
I will be forever grateful!!!
Quote from: olofen on July 12, 2018, 10:29:58 PM
How do I set up my mk III to succeed in filming with 48 fps continuos at 1920x1080 without a break (AND what not to set up...) - I tried everything 😟
Continous: "1920x1080 @ 45p"
NOT 48p.
Quote from: domasa on July 12, 2018, 10:36:48 PM
Continous: "1920x1080 @ 45p"
NOT 48p.
Tried this but stopped after 4 seconds...
Optimize for?
Special set-ups for avoiding crashes?
Hello.
I did not found how to create a new POST... sorry...
I have a question to developers of Magic Lantern:
I need some function for my Canon 5d mk3.
Is it possible to capturing video with maximal width of matrix, minimum height, and maximum fps?
For example 3840 X 20 px, 480 fps
Or 5760 X 20 px, 480 fps (or more)
Who can programming this option? Can I order it? Are here some specialists, who can do it?
Help me please.
Quote from: Shimbarovsky on August 13, 2018, 04:34:03 PM
Can I order it?
https://wiki.magiclantern.fm/faq#when_will_we_be_able_to_shoot_in_our_canon_100_fps_200_fps_1000_fps
I installed the July 2018.3 build and having an issue when recording 1080p RAW footage.
If while recording i press the SET button, the camera freezes and i need to pull out the battery.
Is there something i can check to avoid this?
The loaded modules are mlv_rec, mlv_play and mlv_snd.
Thank you!
Umberto
Does it work using lower resolutions?
Does it work in 1080p and lower resolutions with older builds?
It works in 1080 and records correctly for as long as I wish.
But if, for error or distraction, I press the set button while recording, everything hangs.
I know, just don't press it but I'm wondering what the set button is supposed to do while recording? Should it zoom the display like when not in record mode? Is it possible to disable it?
I didn't check with older versions, if it's worth it I'll give it a go.
Thanks!
It was funny, but You did not read it carefully!
If You change video resolution, the amount of information will decrease, and You can process it faster.
Or is everyone able to reason ONLY in a standart way???
Hello, I made some tests recently 1920x800 - 60 ips - 14-bit lossless with 1920 50/60 3x3 crop mode.
Here is the problem, no clue if it comes from the crop mode or other ML parameters.
Any clue? I speak about the banding effect on the shot. I have it on lots of shots but never experienced that before.
I use the last Switch version to go from .mlv to .dng.
Thanks,
S/.
(https://ibb.co/nRAbcp)
@Shimbarovsky: if your reply was addressed to my post, sorry I don't get it. I wrote that the recording is working ok until I press the Set button, and I was wondering what purpose the Set button has in recording mode.
Sure I must try to record at lower resolution to double check this and report here. Will do ASAP.
Cheers!
Quote from: uuderzo on September 03, 2018, 10:58:22 AM
@Shimbarovsky: if your reply was addressed to my post,
It was not.
Is it possible to use DualIso in conjunction with the experimental set-up with 45 fps and 1920x1080? How do you go about? How do you set it all up in the camera?
Hello,
i'm new here from france (sorry for my english...)
I'm really interested to install magik lantern on my 5d mark iii but i've got some problems...
I've got the firmware 1.3.5 and i cannot downgrade to 1.3.4 or 1.2.3 (wich i need for ML)
I tried with SD card, i tried with EOS utility 3 but it doesnt work.
Finally i saw on the net that i need EOS utility 2 but impossible to install on my windows or mac computers.... Don't know why...
Who could help me please ?
KR
I finally succeed to downgrade until 1.3.3 but cannot go to the 1.2.3 for Magik lantern ... Any ideas ?
https://www.magiclantern.fm/forum/index.php?topic=18941
Sorry if this question seems ignorant, but what is the highest widescreen resolution (16:9, 2:35, 2:39) one can achieve with the crop_rec module in 14-bit lossless, continuous 24fps, while having the LiveView fully functioning during recording?
Just testing my new 5D3 with the 4K / lossless compression Experimental build Jul22.2018
I'm trying to get 45fps as described in the build notes: "1920x1080 @ 45p and 48p (3x3 binning)...Continuous:...1920x1080 @ 45p"
Closest I can get (15ish seconds run) is 1920 x 818 (2.35:1) or 1456 x 820 (16:9) on a Lexar 1066x 128gb. Have tried various combinations of Global draw on/off; Video Previews; Sound off. Nothing seems to hit the stats in the notes.
Could someone suggest some tweaks please?
Many thanks
Tim
Are you recording into SD or CF card @timbytheriver?
@DeafEyeJedi
Hiya! :) Record into CF card. (Lexar 1066x 128gb) I have ML on SD card.
You could test this build:
https://bitbucket.org/Dannephoto/magic-lantern/downloads/crop_rec_4k_mlv_snd_isogain_1x3_presets_2019Feb14.5D3113.zip
version 1.2.3
https://bitbucket.org/Dannephoto/magic-lantern/downloads/crop_rec_4k_mlv_snd_isogain_1x3_presets_2019Feb15.5D3123.zip
It gives 48fps in 1920x1080p. For continuous you do following:
1 - In RAW video keep 14bit lossless
2 - Head over to Crop mode sub menu and change bitdepth to 10bit. (Preview will probably look a bit greenish but files recorded will look good)
@Danne
Many thanks! :) Does that build include all the other modules from the build Jul22.2018 from the 'Experimental' page?
@Danne
That build was for 1.1.3! I got a message warning me about it as soon as I put it in the camera! :( Is there one for 1.2.3?
Updated my post with both versions
@Danne
Great stuff - many thanks! Will test... :P
@Danne
Not sure I'm setting this up correctly. I'm getting about 8 secs (red box from the start) @ 45fps 1920x1080 (Canon menu 1280x720 50fps PAL)
Am I missing something?
(https://ibb.co/YZ4jW1x)
(https://ibb.co/DKHNx4X)
Set to ntsc for 48fps I think.
I think I got contnuous this way. You might have a bad card. You can check your card against benchmark.mo. Just get that module from any other build.
@Danne NTSC/60fps produced lots of code errors and stopped immediately. Set back to PAL.
Are these benchmarks ok?
(https://ibb.co/FKtdJgj)
Do you have a decent cardreader connected with USB 3.x? Use CrystalDiskMark (Windows) or BlackMagic Disk Speed Test (macOS) to verify card speed. Seems a bit slow ...
BTW: Benchmark run writes a BENCHx.PPM file to card's root. You may convert it to PNG to avoid second cam.
Which numbers do you get with plain nightly build in photo mode?
@Walter Schulz Thanks!
Fast card reader/usb 3.0 using Benchmark app gave these results:
Results 55.41
System Info
Xbench Version 1.3
System Version 10.11.6
Physical RAM 8192 MB
Model iMac17,1
Drive Type Multi-Reader -0
Disk Test 55.41
Sequential 99.17
Uncached Write 95.75 58.79 MB/sec [4K blocks]
Uncached Write 92.23 52.19 MB/sec [256K blocks]
Uncached Read 66.23 19.38 MB/sec [4K blocks]
Uncached Read 253.11 127.21 MB/sec [256K blocks]
Random 38.44
Uncached Write 11.05 1.17 MB/sec [4K blocks]
Uncached Write 88.99 28.49 MB/sec [256K blocks]
Uncached Read 1366.83 9.69 MB/sec [4K blocks]
Uncached Read 632.02 117.28 MB/sec [256K blocks]
Do these look suspect?
Can't see the BENCHx.ppm file anywhere on CF or SD card.
That's a bit slow for a 1066x card. Sequential write should be between 115 and 156 MByte/s with a cardreader supporting UDMA-7. Maybe it's you mac/cardreader combination...
The file you are looking for is named BENCH0.PPM or BENCH1.PPM or Bench2.PPM ...
Run another benchmark with plain nightly build in photo mode and report back.
@ Walter Schulz Thanks for looking that over. I guess I'd better contact the seller (Amazon) for a replacement.
https://www.cameramemoryspeed.com/reviews/cf-cards/lexar-professional-1066x-128gb-cf-card/
"The Lexar Professional 1066x 128GB CompactFlash card offers high performance and large capacity. It supports UDMA-7 and it rated at 160MB/s read and 155MB/s write speeds according to Lexar. The large capacity is ideal for video recording, and it carries the Video Performance Guarantee rating of VPG-65, meaning the card will sustain at least 65MB/s continuous write speed."
Is that figure of 65MB/s quoted the one the ML bench test is giving (61MB/s in my case)?.
No .ppm files anywhere to be seen!
Is it to much asked for another benchmark run in photo mode with plain nightly build instead of jumping to conclusions?
@Walter
I don't quite understand "run in photo mode". What's the correct procedure for running the ML benchmark test?
I've been testing the card for some days; in various builds using 45/48fps and am getting nowhere near what others are achieving in record times. I wouldn't say I'm jumping to conclusions...
Your cam has two modes: Photo/stills and movie/video and there is a switch right to the eye-piece with respective symbols. Do not enter liveview in photo mode for this benchmark run.
Is mv720p or mv1080p also affecting benchmark results? If so set it to mv1080p when testing as well.
@Walter Thanks! Do these look more healthy? Now I have the .ppm files... :P
(https://ibb.co/bKNKFS5)
@Danne Thanks!
And now do it again with plain nightly build.
Plain vanilla nightly:
(https://ibb.co/mh6ptZ4)
Just to be sure:
@5D3.123 owners in possession of a 1066x card: Do a benchmark run in photo mode outside liveview and post results (best convert BENCHx.PPM to PNG and link it here).
I really don't know what 'plain vanilla' means (not English native speaker) but using Danne's last page's Feb Build 1.2.3 with an extra bench module I got this:
KOMPUTERBAY 64GB 1066x
(https://ibb.co/TBmvz9B)
LEXAR 128GB 1066x
(https://ibb.co/YbKK6yq)
TRANSCEND 128GB 1066x
(https://ibb.co/RBrNWKz)
Quote from: Sganzerla on March 09, 2019, 05:56:55 AM
I really don't know what 'plain vanilla' means...
"Plain vanilla" in this case means a Nightly or "unified branch" build. In other words, something basic that is not experimental or modified in any way. One of Danne's builds would go beyond experimental into what is know as a "bleeding edge" build.
@Sganzerla: Thanks for testing!
@timbytheriver: There is one test left. I'm guessing you have ML installed on your SD-card and use your CF for storing data. If so: Run ML with CF only and redo benchmark test. Don't expect the numbers to change. It's just the final test before replacing the card.
@Sganzerla Thank you!
@Walter Righto. Do you mean install ML on the CF card alone – and leave out the SD card? Will try...
Interesting to note the difference in the reported names of my Lexar card (SMI Silicon Corporation) Vs @Sganzerla's (Lexar ATA Flash Card). I suspect mine's a fake...
CF card install alone:
(https://ibb.co/2tRdKF9)
Still very poor... >:(
Write speed seems not what advertised. Bad card maybe.
@Danne Yes! Or a fake one... Just noticed mine says 'Made in Vietnam' in tiny printed letters. ???
Doesn't have to mean anything. We live in a global economy and production sites may be spread all over the world.
IMO the whole "Made in ..." thingy is worthless today.
And Lexar Brand is owned by chinese company Longsys since 2017.
No way (yet) to tell if there is a difference between cards made in different locations.
@Walter I guess. I will certainly contact the seller with the evidence.
Ah, memory flash-back ... (SCNR):
We had this issue before, see https://www.magiclantern.fm/forum/index.php?topic=12630.msg135713#msg135713
Some manufacturer, same ID line and long before transfer of brand to China.
May I ask for a favour? Can you share (= for common use) some high-res photos of the card (CR2 preferred) showing label and front side? I might come up with a tutorial/primer about cards for ML and might be able to use such pics.
@Walter Very interesting! Same controller ID. Here's link for requested pics: https://we.tl/t-jy6S1romfu
@Walter Edge pic as requested: https://we.tl/t-TWX3A9hLCM
Just received new KomputerBay 1066x 128gb from Amazon. Benchmark much more respectable. Test @45fps continuous (green) 1080p fine. :) Strange that is shows the same ID line as the Lexar though... Odd. :-\
(https://ibb.co/1Jbw97w)
Are IRND filters recommended for the 5Diii? Or is it effective with IR cut?
In Europe should the camera setting be on PAL even though I'm shooting at 24 FPS?
I just ordered a Lexar 1667x SD card in order to test recording MLV to that instead of the slower CF card. However for some reason I'm unable to get ML to record to the SD card. I can record to the SD card fine if I shoot with the Canon software but not from ML regardless whether I have the SD card set as the preferred card or not. I'm using build: magiclantern-crop_rec_4k.2018Jul22.5D3123.
Would appreciate any advice! Thank you!
Without overclocking 5D3's SD-card interface is limited to about 25 MByte/s.
5D3's card slot has UHS-I interface. Your card hosts UHS-II interface but has to run in UHS-I mode with this camera.
You have to use fast CF-cards (supporting UDMA 7) for maximum bandwidth.
That's too bad but understood. Thank you!
Is there any way for me to get the 5diii to keep from powering off? It will go about 30min and then auto power off.
Application: I'm using this as a broadcast camera for a live production and would prefer it just remain powered on until I turn it off (manually).
Set it to "Disable"
Just benchmarked a KomputerBay 128gb 1066x, this must be the slowest copy ever...
Is this card defective or am I using the wrong settings?
Use a decent UDMA-7 compatible cardreader and CrystalDiskMark (Windows) or Blackmagic Disk Speed Test (macOS) to verify your results.
Quote from: Hydrazine on October 25, 2019, 06:03:23 PM
Is this card defective or am I using the wrong settings?
Had the same issue with Komputerbay 64GB 1000x. Solved by properly formating in a UDMA-7 capable reader (with USB 3.0). You can also try to low-level format inside the camera, might work.
If this doesn't work, I would assume you probably have a broken card.
Tried formatting multiple times, using both ExFAT and FAT32. Similar results each time. Low level format in camera doesn't help unfortunately. Strangely, in crystaldiskmark, the benchmark results are significantly higher, (read and write 65-70MB/s) but still not to spec. I suspect a compatibility issue with the controller is making the 5D3 not use UDMA 7 and instead some slower mode. In any case, it's going back!
I put it here ...
Found it via SLRlounge (https://www.slrlounge.com/why-you-should-not-use-an-sd-card-in-the-canon-5d-mkiii) and the original blog post is linked:
https://blog.jeffcable.com/2012/06/why-you-should-not-put-sd-card-in-your.html
Maybe a1ex can give a word or two. Minor error: 5D3 works with 166x (theoretical) as in UHS-I SDR25 mode (AFAIK).
Don't know if it's worth the effort to comment his blog entry ...
Short answer: the two card slots are independent; there are two different controllers. The presence or speed of a SD/CF card does not affect the speed of the other card. You have bench.mo, feel free to prove me wrong ;)
Of course, if you enable the option to save each image to both cards (in Canon menu), the slowest card (SD) will be the bottleneck. That's expected.
Or, if you attempt to write to both cards
at the same time, the memory bus appears to be the bottleneck. Can be worked around, to some extent, e.g. by disabling "unnecessary" LiveView image streams.
Quote
One more thing. Most of the time, this is a hardware limitation and can not be solved with a firmware upgrade.
It can (with sd_uhs), as the hardware appears to be the same as in other DIGIC 5 models. Maximum speed is still an open question, if you ask me, but further investigation will probably require a good logic analyzer, rather than "blind" trial and error.
HELP
hey all
hope someone can help
i have a 5d mark 3 with 1.3.6 firmware.
Is there any way i can downgrade the firmware to 1.2.3
Quote
Is there any way i can downgrade the firmware to 1.2.3
Contact Canon service
Thanks
Quote from: Walter Schulz on December 16, 2019, 03:18:53 AM
Contact Canon service
No... I asked to the CPS of my city (Rome) and they told me they can't do the downgrade...
:'(
Other CPSs can and did.
hi , I'm new to this forum and not yet Install the magic lantern, i have 2 5diii and i will Like to know please What's the best Recommended firmware And where I can download it And if it's possible steps By Steps and If it's on YouTube It's better, The main reason As of now That I would like to install the program is for the Slow motion And I hope it can do that, Any response would be appreciated,
While ago I research If This program Can do the autofocus in video mode And I find out That it cannot,However I'm sure there's a lot of advantage To this program Besides that
Top of page -> Downloads -> Download nightly builds -> 5D Mark III 1.1.3 -> Installation (for installation instructions) -> Notes (for which one is "better")
I have Canon 5Dm3 1.2.3 i want to use CF for videos and SD for photos. can i use CF and SD in the camera at the same time? I need to install ML to CF or SD card? How to boot from CF card, not sd?
also if i install ML to CF can i take it out and put in a CF or SD with no ML installed?
thank you for answers)) 8)
Top of page -> Downloads -> Download Nightly Builds -> 5D Mark III 1.1.3 -> Installation -> Recommended card setup.
Applies to 5D3 1.2.3, too.
What's the main difference between 1.1.3 and 1.2.3?
I'm about to buy a 5d with this stimulus check since my 7D sensor is just bad.
I still want Magic Lantern and Canon photo quality.
So I'm looking really heavily into 5d mk iii.
Quote from: domo94 on May 03, 2020, 03:17:12 AM
What's the main difference between 1.1.3 and 1.2.3?
Top of page -> Downloads -> Download Nightly Builds -> 5D Mark III 1.1.3 -> Installation -> Notes -> Link to feature list and forum thread.
Ah, redundant compared to last comments.
Thanks for that.
Now a better question would be, what are the significant differences?
I do need HDMI out so I would be looking at the 1.2.3 firmware.
Is the 1.1.3 build just more robust and reliable?
Are recording performances the same between each build?
1.1.3 recommends to use this build if you consistently record with ML, which I do and intend to do if I get the 5d mk iii
Sorry, haven't you read "Notes" and first post of linked forum thread?
Yes
But it doesn't really answer my question.
I have many more.
I'm more concerned about its consistency with 60fps raw shooting.
I don't want to frame skip, I want to have true full continuous recording with sound in 10bit. I've scouted the forum before as I was very keen on seeking the very limited info on my 7D.
I'm juggling the canon rp as an option and would possibly even try to port that if possible.
I can't keep working the way I do, especially with the limitations I've done my very best to get around.
I seriously am having a very hard time breaking up with magic lantern.
Quote from: berechiah on December 15, 2019, 10:16:30 PM
HELP
hey all
hope someone can help
i have a 5d mark 3 with 1.3.6 firmware.
Is there any way i can downgrade the firmware to 1.2.3
Yes, this is from the ML 5D MKIII nightly Build page and it works:
Downgrading from 1.3.6 is possible, but tricky.
Whatever you do, do not remove the battery in the middle of a firmware update!
____________________________________________________________
One single card required, either SD or CF, source, discussion):
copy firmware 1.3.6 (5D300136.FIR) to the card
launch Update Firmware from Canon menu, click OK
open the battery door ASAP, but don't remove the battery!
if you did it right, the camera will turn off (wait for a few seconds to make sure it's really off)
if you see the Firmware Update Program Loading screen, it means you have opened the battery door a bit too late; wait until the camera turns off and try again!
open the card door and remove the card from the camera (do not close the battery door; also leave the power switch on; the camera should stay off)
copy firmware 1.2.3 (5D300123.FIR) to the card
put the card back into the camera, close the card door
you may leave the original 1.3.6 FIR on the card, or you may delete it; doesn't matter
close the battery door; you should see the Firmware Update Program Loading screen
if you get an error message at this step, remove the battery and reboot
confirm the firmware downgrade from 1.3.6 to 1.2.3
a successful downgrade should take about 4 minutes.
______________________________________________________________
I have done this so I know it works.
This is the most important step: open the battery door ASAP, but don't remove the battery! - ASAP means immediately. ANY delay and this will not work. But it does not do damage, just means you have to try again but faster!
Hello, just got the Mk3 and the latest build (7-3-2018). I haven't had any issues but how does one record higher than 1920x 1080 with raw? Also are there any new builds in development?
Thanks and happy Memorial Day weekend!
Quote from: DaRealTurbo on May 23, 2020, 06:48:34 PM
how does one record higher than 1920x 1080 with raw?
Press magnify/loupe/zoom button.
Quote from: DaRealTurbo on May 23, 2020, 06:48:34 PMAlso are there any new builds in development?
Top of page -> Downloads -> Downloads (drop down menu) -> Experiments -> 4k crop builds.
I have1.3.6. thanx to canon repair. Having the worst time. This is to clarify previous post.
attempting to downgrade, frankly to anything, have tried 1.1.3 and 1.2.4 on two sd cards, but regardless what FIR i download, my 5d3 only reads as 1.3.3??? and does not load ML nor ever downgrades.
Ive spent weeks searching and trying to no avail. just cannot get rid of 1.3.6
Thank You again
Follow instructions described as "Method B" to the letter!
https://builds.magiclantern.fm/5D3-123.html -> Installation
If you still have troubles: Record your steps with another cam (smartphone is ok) and link video here.
PS: No idea why you are trying 1.2.4. There is no ML for this version and it is not part of the installation instructions!
Hello all
Please help me choose
I decided to buy 5Diii or 6D
I am interested in the video more than the pictures
6D has a continuous focus while 5D iii does not have a continuous focus
Does the continuous focus work on ML
I ask those with knowledge and experience to help me make a decision because I do not know how these cameras handle ML
I apologize if the place is wrong
I just wanted the owners of the camera to help me so I wrote here
Please do not crosspost!
Quote from: shhd on August 01, 2020, 04:45:36 PM
Please help me choose
I decided to buy 5Diii or 6D
Can I have a try giving an advice? In my opinion, the best buy is 5D3, because it is the best camera for ML and especially for shooting an uncompressed video (losslessly compressed, more like zip, rar or whatever). You can use the fastest SD and CF cards, overclock the SD controller with sd_uhs module and use the card spanning mode, when 5D3 writes on both cards simultaneously. Thus you'd be able to shoot in the highest definition possible. Non-anamorphic 1-1 mode is 3K and anamorphic full frame mode is 5.7K if I'm not mistake, all 25fps, thanks to Danne. You can also shoot in 1080p full frame binned mode. You cannot shoot 5.7K or even 3K with 6D continuously. I can do that with 5D3 with SD Sandisk Extreme Pro 64 GB 170 MB/s and CF Sandisk Extreme Pro 128 GB 160 MB/s installed.
So, I'd like to advice you to buy 5D3.
The key point is that you have to choose the 5D3 with the Canon firmware version 1.2.4 or less, to be successfully downgraded to 1.1.3 or 1.2.3. I was a lucky because I've bought the cam with 1.0.4 firmware, so I had to
upgrade it.
I've had ML on this camera before, sent to Canon, now it's got 1.3.6 and I've spent endless weeks doing endless tweaks to no avail. Have tried every firmware version, can't get rid of 1.3.6 camera reads all fir's as 1.3.3 and does not load
, 1.3.6 won't go away
IM GOING MAD
First step: Format card in cardreader. Second: Format card in cam.
Proceed from here with
Top of page -> Downloads -> Download nightly builds -> 5D Mark III 1.2.3 -> Installation -> Installation -> Method B.
Follow instructions to the letter.
If unable or an undocumented error occurs: Make a video of your installation steps and link it here.
Does this camera do 10 bit raw, 60fps, AND sound at the same time?
Thank you Walter S.
I will attempt, and notify this thread
Actaully was able to download 1.3.6 to 1.3.3. Not sure why 133!
Now im attempting to downgrade from 1.3.3 to 1.1.3, but having issues. will continue tweaking and update here.
Use EOS Utility to downgrade from 1.3.3.
Quote from: miatch on August 04, 2020, 01:05:04 AM
I've had ML on this camera before, sent to Canon, now it's got 1.3.6 and I've spent endless weeks doing endless tweaks to no avail. Have tried every firmware version, can't get rid of 1.3.6 camera reads all fir's as 1.3.3 and does not load
, 1.3.6 won't go away
IM GOING MAD
The following explanation was given
I made it back from 1.3.5 to 1.2.3
You need an official version of the Canon website that is higher than 1.3.6 on the camera so that you move to the next step after the camera reads that the version in the memory is higher than the version in the camera and as soon as the light turns off, open the door and insert a new card containing version 1.2.3.
Your problem is that the camera version 1.3.6 needs an official version higher than 1.3.6 in order to be able to trick the camera
I suggest all users to ignore advice above and strictly follow procedures explained by a1ex in the installation instructions.
https://builds.magiclantern.fm/5D3-113.html#install
https://builds.magiclantern.fm/5D3-123.html#install
Quote from: Walter Schulz on August 12, 2020, 02:31:18 AM
I suggest all users to ignore advice above and strictly follow procedures explained by a1ex in the installation instructions.
https://builds.magiclantern.fm/5D3-113.html#install
https://builds.magiclantern.fm/5D3-123.html#install
Suggest that you thank the efforts of the members who are trying to help
Myself I made it back from 1.3.5 to 1.2.3
It first failed because the card was inside
1.3.5 and camera 1.3.5 The camera is rejected and a higher version is required
I downloaded 1.3.6 from the official website
And I applied the rest of the steps, and it succeeded
The camera rejects any version equal or less
When I read the camera in memory, version 1.3.6, higher than the installed version, the camera continued and when the red light stopped, it opened the door and placed a memory containing 1.2.3 and 1.3.6.
I chose 1.2.3 and it worked
http://www.catb.org/~esr/faqs/smart-questions.html#not_losing
hello guys need help
can we get clean HDMI output using 5DM3 firmware 1.2.3 with crop_rec_4k_mlv_snd_isogain_1x3_presets_2020Sep14.5D3123 recording 3K 1:1 , 14 Bit , 23.976
and is there any setting in the menu canon to improve the performance
thank you
Try Display tab -> Clear overlays
thanks Walter Schulz but still same not working
Support staff really love that reply "not working".
Maybe you want to show the setting you are using and a screenshot showing HDMI output.
Sorry I'm not really familiar with the interface I don't know how to upload screenshots I will try now
I didn't find the how upload screenshots really sorry
Please if you can explain me
Thank you
Magic Lantern Forum »General Discussion »Magic Lantern Forum and Site Discussion »Sticky thread "How to add images to posts on the forum?"
ok walter thank you for your help i did put the picture on my google drive i dontknow if it wil working but i will try
this is a test
Wrong screenshot.
I want to look at
- Display tab
- HDMI screen output
And set Kill global draw ON, too.
i use ftp link as i use my ggogle drive i hope its working
and im not understand (And set Kill global draw ON, too.) do you mean global draw set live view
ok this is the 5D3https://drive.google.com/file/d/1V5WLFwEb36-aIJA5mOdG319Ngjrg97ai/view?usp=sharing (ftp://drive.google.com/file/d/1V5WLFwEb36-aIJA5mOdG319Ngjrg97ai/view?usp=sharing)
and this is the ninja https://drive.google.com/file/d/1pYmDcAQvLpaLGrAukrrhQ8hH36SSHulp/view?usp=sharing (ftp://drive.google.com/file/d/1pYmDcAQvLpaLGrAukrrhQ8hH36SSHulp/view?usp=sharing)
if i use the setting with crop mode its working the hdmi screen output its working but when i use setting 3K 1:1 i got this weird screen i hope you cansee the sreen shoot
thank you Walter trying to help me
sorry this the link https://drive.google.com/file/d/1V5WLFwEb36-aIJA5mOdG319Ngjrg97ai/view?usp=sharing
https://drive.google.com/file/d/1pYmDcAQvLpaLGrAukrrhQ8hH36SSHulp/view?usp=sharing
Almost there.
I want to see this screen:
https://drive.google.com/file/d/1wKU_0-J9gQN1CTAsRkHx7pR_671s96xw/view?usp=sharing
yes idid try everything in display tap and still same weird screen
Unable to open file. Requires google account ...
Support staff hearing "tried everything" tend to moan and regretting to be born.
https://drive.google.com/file/d/1kDj6v-O1KI27XwbglMtt9YYZsZzf7ebn/view?usp=sharing
https://drive.google.com/file/d/1VLWBLRXbfY5qt9hOoQnPZnlBdHDgtFSs/view?usp=sharing
https://drive.google.com/file/d/16dgcALMzQ31H2mimIyi5wU5dfAqD61c4/view?usp=sharing
this is my actual setting with still same weird screen
I will not use anything requiring authorisation. Try any pic hoster. Imgur or anything else not asking for user and password.
ah sorry ok so how to do if you dont have google account i didnt know about that
i mean i did try all your suggestion
i wil try with youtube
can not on youtube so i dont know how to do
thanks for your help Walter
are you on facebook group magicl lanter
i have 3 groupe on facebook with magic lantern MLV RAW ON EOS M,MAGIC LANTERN FRANCE , MAGIC LANTERN CANON
i can do a post in one of them or all of them
For starters: Try https://imgbb.com
or any other image hoster. There are dozens.
And i do not use Facebook and none of these groups is supported by ML staff.
BTW: What are you trying to do? It looks like you are RAW/MLV recording and HDMI streaming/recording at the same time?
Thank you for keeping help me
this is the link
https://ibb.co/NNbZJ3b
https://ibb.co/8skHZXG
https://ibb.co/ZSbyYwL
https://ibb.co/tB8v45K
https://ibb.co/gDnQkhH
You haven't answered what you are trying to achieve. Simultaneous MLV and HDMI recording?
Just to humour me: Remove ML card(s) and startup cam. Play around with menu setting "HDMI output + LCD" to get clean HDMI out. Now insert ML card and retry. Report back.
no i dont look for recording in both of them i just want have a monitor control and keep recording MLV in my intenal memory card
i just bought a gimble zhiyun crane 3S Pro with transmitter and receiver i want to send video to an other monitor
the hdmi output its working perfectly when i take of the mlv card
its working also very good when i use mlv but the crope mode X5
its not working when i use the setting 3K 1:1 even the inside the camera without external monitor i dont have clean have clean screen screen i can not get realtime clean on my screen camera
It's not easy to follow your post. Punctuation marks might help a bit. Please move discussion to proper thread
https://www.magiclantern.fm/forum/index.php?topic=23041.0
so sorry for my english
thank you for your help
If this is the wrong place to post this let me know!
So I have been trying out recording 1080p60 with MLV Lite 1.1 on Firmware 1.2.3. I am recording with no FPS overide and it SEEMS to be doing well but I am confused by something? Is it dropping frames if it is not green? What does orange neat with numbers beside it? Is it how many frames are still left in the buffer while the card is catching up?
Also, I posted this question elsewhere but is there any way to display how much time I left on the card at the current bitrate/format? I have REC Indicator set as Remaining Time but nothing seems to be showing that still anywhere on the screen?
THANK YOU everyone who is working so hard to make my $800 camera do things that only 3000-4000 cameras can do. Still so blown away by this!
Hi, anyone still have a copy of the Firmware 1.2.3 ?
Top of page -> Downloads -> Download nightly builds -> 5D Mark III 1.2.3
Firmware linked in "Installation" and "Useful Links"
Solved...another browser let me download it.
HDMI Problem.
I never had to problem before. But when i want a signal from the HDMI out, there is no signal at several devices like BMD Video Assist, external display etc. But when i plug it to a TV then there is no problem.
What could it be?
Please clarify:
Build used?
LCD display is working while external HDMI is connected?
Have you tried with/without ML active? Just bypass ML start by pressing SET at startup.
I think the external monitor settings
I had the same problem there is a setting I don't remember now but I will turn the screen back on and let you know soon if I find time
I had an external recording screen and in the main menu there is an option related to the degree, strength or method of receiving the signal and the options were two options made up of numbers, one of which was working with 5Diii
and the other works with 5D iv
Try searching the screen settings in the signal capture
Hello guys, does anyone know how to get a signal from the camera about the beginning and end of the recording. It is necessary that the start / stop video is synchronized with external equipment. Essentially analogous to timecode. Connector c3 only works for signal reception?
you should probe c3 with a multimeter, you may find that shutter half-press pulls one of the pins on this port low. In this case use the "shutter half-press start record" feature and when you trigger recording via this feature you can detect the logic from C3 with a microcontroller and use it to start/stop your audio or whatever device you are attempting to sync to
The post you answered is from more than 11 months ago and user dream951 last online date: June, 2022.
Quote from: Walter Schulz on January 23, 2023, 08:32:03 PM
The post you answered is from more than 11 months ago and user dream951 last online date: June, 2022.
You're right
[MOD intervention)
Crosspost/spam deleted