Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Exile

#1
Coming from 1.1.3 Do you simply fomat card with ml on, then update firmware to 1.1.6 and then put ML for 1.1.6 on your card?

Thans in advance
#2
Hello, Ive been away for a wile and are still running tragic lantern.
If i want to update to magic lantern is it as simple as removing tl files and replacing them with ml files(like normal update)
or do I need to do something more?

Thanks in advance!

Gr, John
#3
BTW

In what situation would you use auto expo?

You always have the desire for a sertend aperture or shutterspeed, or am I missing something?
#4
Ah oke, thanks for clearing that up.

Sounds like that is what i'm looking for, i would like to have a set shutter speed a variable aperture and depending on those 2 an as low as possible iso.
Canon already does this if i put auto iso on and put a minimum shutterspeed and shoot in aperture priority, but for some reason most of the time i get (much) higher shutterspeeds
then my minimum setting what leads to high iso setting which is not what i want.

Gues i misunderstood auto expo, sorry for noob question and i will be looking out for auto iso!
#5
Oke that changes it, alhough its 2.8 4.0 or 10.0, why can't it be changed with main dial as it would normally do in m mode?
#6
I've been trying out autoexpo but i can't seem to get to change the aperture, it stays wide open(2.8 in my case) am i missing a setting? I read through this tread but can't find an answer.

Thanks in advance
#7
Duplicate Questions / MLV_Dump
November 12, 2013, 02:07:53 PM
Hey,

After reading alot of topics, I am stil confused is mlv dump a program
or is it a command line?

I have a couple of mlv files which won't be processed
by mlv2dng and I read that mlv dump can make the difference

Anyone who can educate me?

P.S. Sorry for bad English....
#8
Quote from: Aliiphotos on October 29, 2013, 02:15:06 AM
Hey, thanks for the tutorial. It worked out well but not perfectly for me  :-\ . I have a lot of the features of ML like HDR in photos but the HDR video is greyed out and not an option. Could anyone elaborate on how to fix this problem? Thanks so much!

Are you in video mode? do you have selected an ISO value? you cant select it if your in Auto ISO mode.
#9
Quote from: lbburnsy on October 28, 2013, 11:13:47 PM
So I successfully managed to install the software onto my camera, but once I attempted to shoot I could not record the raw video as it would stop automatically.  The card I'm using is a SanDisk Ultra 32 GB 30 mb/s 10 speed SDHC card.  I have no clue where to go from here...

I'm not sure, but I believe you need UHS-1 speed
#10
General Help Q&A / Re: ML Best Practices
October 28, 2013, 07:30:30 PM
Quote from: nanomad on September 14, 2013, 09:27:44 AM

Using the same card in two different camera models - possible?
It will work, but we do not recommend doing this. The settings which are camera-specific may not be preserved properly in the configuration file.

Hi, do you refer to same ML version for 2 cameras, because I was wondering if I could use 1 card for 2 cameras who both require a diffrent ML

in this case i'm talking about a 6d and a 6od, would it be possible to have 2 ML versions on 1 card so that the camera would load the ML version that is required for that camera?

Thanks in advance, John
#11
Share Your Videos / Canon 6d MOV vs RAW
September 22, 2013, 06:38:35 PM


The RAW file is oversaturated, still  messing around with the RAW grading
#12
Share Your Videos / 6d RAW video, Aqua
September 22, 2013, 06:35:48 PM
My first experience with RAW on the 6d

Shot in 720p 24fps, maybe a little to much noisereduction

#13
Thanks for the confirmation! I'm not quite used to this pre Alpha stuf, I have only ran
2.3 on 60d but now i'm kinda used to the extra's ML brings :)
#14
Quote from: noisyboy on August 18, 2013, 07:58:42 PM
Hey bud! You're welcome! Sorry but I've been so busy filming the last month or so that I still haven't tried any of the cool dual iso stuff out for myself yet so one of the other guys might have to answer this as I need to do lots of catching up :) In fact last time I checked it wasn't available for the 6D it's been that long! Does this work now 1%? Cheers man!

Filming is good :) Thanks for your reply. I was not sure if I had to downgrade the firmware or if I could run the dual iso version on 1.1.3
so now I simply leave it to1.1.3 and replace the ML folder and the bin file?
#15
Tragic Lantern / Re: Tragic Lantern for 6D
August 17, 2013, 12:16:46 PM
Hey,

I have ML(raw video version) installed (http://www.magiclantern.fm/forum/index.php?topic=5530.0) and now i want to try the dual iso version. Does anyone know if i can simply replace the ML folder and the autoexec.bin file? Or do I also have to delete the 6D000113.FIR file?
#16
Hey noisyboy thanks for this handy tutorial!

Q: if i wanted to test the new dual iso ML can i just simply follow your tutorial and replace the ML thats put on in step 13?