Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - waelti_de

#1
General Development / General compiling problem
September 03, 2017, 07:21:21 PM
After the VM with 1.3 GB from 2013 has the same problem and the other VM doesn´t start, I tried to build mine with Debian 9. I think I found all packages I need to install after the minimal installation. The compiler is gcc-arm-none-eabi-4_8-2013q4
Now my problems:
If I do a "make", all cameras will be compiled with the exeption of the 7D:

[ SYMBOLS  ]   magiclantern.sym
[ CP       ]   7D_203.sym
make[1]: Leaving directory '/home/ml/magic-lantern/platform/7D.203'
make -C  /home/ml/magic-lantern/platform/7D_MASTER.203
make[1]: Entering directory '/home/ml/magic-lantern/platform/7D_MASTER.203'
[ VERSION  ]   ../../platform/7D_MASTER.203/version.bin
[ LD       ]   magiclantern
../../src/Makefile.src:196: recipe for target 'magiclantern' failed
make[1]: Leaving directory '/home/ml/magic-lantern/platform/7D_MASTER.203'
Makefile:18: recipe for target '7D_MASTER' failed

After disabling the 7D all is fine, but this can not be the solution.

When I do a "make zip", at first "make docs" is executed. It seems, that there is only executed the first line:
cd $(DOC_DIR) && RST2LATEX=$(RST2LATEX) $(PYTHON) mkdoc.py

then I get an error:

../../Makefile.inc:49: recipe for target 'docs' failed
make[1]: Leaving directory '/home/ml/magic-lantern/platform/all'
Makefile:105: recipe for target 'docs' failed

If I execute both lines in the console, all works fine with no error:
   cd doc && python2 mkdoc.py
   cd doc && python2 mkdoc-cam.py

Where can I raise the debuglevel to find the errors? Can anyone give me a hint, where these errors came from?

#2
In Beta4 there is no point to dump ROM, is there a release which can do it?
#3
General Development / make zip doesn´t work
May 27, 2014, 11:44:02 PM
Since a couple of days "make zip" doesn´t work anymore, because 600D and 6D have compiling errors (600D since 15th of May 2014 and 6D since 23th May 2014).
Does nobody check this ? Why isn´t a complete zipfile availabe for download ?

Kind regards
Walter Reis
#4
I don´t use any video feature of ML, I use trap focus, focus stacking, focus peak etc. , because my main interest is macro photograpy.
My biggest wish would be, to take a photo in RAW resolution without using the shutter. If I make pictures in a magnification of 5x and higher, the smallest vibration results often in a picture, which could be sharper without shutter movement.
As I read from the success to make movies in RAW format in the 5D MKIII, I got a new hope for me, that it could be possible for pictures too. Is my hope justified ? :-\
My camera is a 50D.
#5
Is it possible to display focus peak in live view with activated zoom (5x and 10x) ?
I use focus peak very often, mainly when I do macros. It would be great to display focus peak in zoom mode in liveview, because the sharp area in a macro is sometimes only 1/10 mm, and with focus peak it would be much more easier, to find the exact point of sharpness.
#6
Hello guys,
I have tried several descriptions to use focus stacking on a 50d, but it seems, that this is to difficult to me  :-[
Is there a step by step description how to set it up on a 50D ?
Descriptions on a 60D doesn´t work on a 50D.
Can anybody, who has a 50d, tell me, how to start it ?
If I push "Focus End Point" on the videos liveview appears again (at me too), but I can´t change the focus range and therefore the message is always "will take 0 pictures"

Firmware 1.09
ML 2.3

Kind regards
walter